Unlock Your Potential solutions for continuous improvement
solutions for continuous improvement STEP 1: Discovery OUR GOAL: TO UNCOVER CONTINUOUS IMPROVEMENT P O T E N T I A L STEP 2: Identify Key Drivers THROUGH IDENTIFICATION OF KEY VALUE A N D NON-VALUE ACTIVITIES IN THE FABRICATION PROCESS. STEP 3: Documentation Review & Proposal MEASUREABLE BENEFITS TO THE CUSTOMER: INCREASED OUTPUT OVERALL WELDING COST REDUCTIONS IMPROVED QUALITY STEP 4: Implementation STEP 5: Monitoring & Verification
solutions for continuous improvement In-depth analysis by industry experts shows that labor is the major cost driver in most fabrication operations. Our goal at Hobart Brothers is to help you reduce labor for non-value-added activities those tasks that don t contribute to your overall productivity or bottom line. And we can lower your overall costs along the way. How? With our exclusive Improvement Potential (IP) Methodology that looks at: PRE-WELD ACTIVITIES WELD ACTIVITIES POST-WELD ACTIVITIES This approach helps you identify the potential for productivity improvements and cost savings in your fabrication operation, specifically where most non-value-added labor occurs: in the pre- and post-weld areas.
solutions for continuous improvement Consider the cost breakdown of a typical welding process: Labor 85% Electrode 10% Power 2% Gas 3% In many welding operations, a large percentage of the labor (as shown here) is non-value-added. It is used for costly activities like grinding, sandblasting or chipping that may not be necessary and that could be lowering your potential for greater productivity. We can help you determine if these activities exist in your welding operation.
The technical support we received throughout the conversion process can t be touched. Our Hobart representative showed how we could improve our weld quality and productivity with a new wire, plus reduce our clean up. These benefits were the real selling point. MILT SIESKY, SENIOR INDUSTRIAL ENGINEER/WELDING, JLG MCCONNELLSBURG, PA
solutions for continuous improvement Step 1: Discovery Hobart Brothers Improvement Potential (IP) Methodology focuses first and foremost on developing a long-term, mutually beneficial partnership between our company and yours. It s an approach we believe in and it begins by listening to your needs. We first engage in a sharing discussion and a brief walk though your facility. Our objective is to identify areas of your welding operation that can be enhanced. We also look for non-value-added activities that may be hindering your productivity and/or unnecessarily increasing your costs.
The Hobart team helped us get the right parameters for our metal-cored wire and provided more technical support than I ve gotten from any other company. It was phenomenal. Plus, with the metal-cored wire, we ve gotten nearly a 30 percent increase in productivity with our robots. CARL BAATZ, PLANT MANGER, SQUARE DEAL MACHINING MARATHON, NY
solutions for continuous improvement Step 2: Identify Key Drivers Hobart Brothers has highly trained experts that work directly on the shop floor to identify key problems that you and your team can then prioritize. Depending on your particular welding operation, we can even provide robotic or process support to help in the assessment. Some of the areas of the welding operation we examine during the IP Methodology process are: Part Movement/ loading Part Movement/ Indexing Part Movement/ Unloading Pre- Cambering Sand Blasting Arc-on Time (Welding) Air Movement Weld Repair Reject Sand Blasting Fill-up & Tack Antispatter Application Pre-weld Activities Blending Grinding/ Blending Antispatter Application Weld Activities Grind/ Blend Fill-up & Tack Part Cleaning/ Rinsing Post-weld Activities Chipping/ Scraping Grinding/ Blending
Our IP (Improvement Potential) Methodology helps us help our customers. It s exciting to provide the tools they need to uncover productivity increases and cost reductions in their welding process. DOUG KREBS, HOBART BROTHERS BUSINESS UNIT MANAGER
solutions for continuous improvement Step 3: Documentation Review & Proposal After compiling data into a final report, Hobart Brothers experts review their findings with you in an open forum. Depending on the data collected, the report may include suggestions for alternative methods, materials and/or processes, or we may conclude that additional information or verification is necessary. It s then your decision whether to implement some, all or none of the suggestions we ve provided.
It s rewarding to know that we can analyze a customer s fabrication process and then offer them a real solution to increase their productivity. It s even better to see what a difference it can make on their bottom line. PETER CORTINA, HOBART BROTHERS BUSINESS DEVELOPMENT MANAGER
solutions for continuous improvement Step 4: Implementation We recognize that your time is valuable. Should you proceed with the improvement proposal Hobart Brothers provides, we will be with you every step of the way. Our goal is to provide seamless and prudent transitions and also to offer the resources you need to be successful. These include: ~ WELDER TRAINING ~ CLASSROOM TRAINING ~ MACHINE SET-UP ~ ROBOTIC SUPPORT ~ PART RUN-OFFS ~ METALLURGICAL ANALYSIS ~ ETCHED CROSS-SECTIONS
There are so many factors that affect a customer s total weld cost. That s why our IP Methodology analyses the entire fabrication process, not just the welding process. It especially let s us look at ways to eliminate pre- and post-weld activities and lower our customer s overall costs in those areas. RICK CONRAD, HOBART BROTHERS BUSINESS DEVELOPMENT MANAGER
solutions for continuous improvement Step 5: Monitoring & Verification Hobart Brothers support doesn t end after implementing your improvement proposal. Our representatives follow-up regularly to monitor all areas of your operation, including your pre- and post-weld areas. We want to verify that your welding process is reaching it s productivity and cost-savings potential.
Hobart Brothers Key Account Management (KAM) Summary Report
Code Welding Procedure Detail Current Procedure Total # of Weld Passes Procedure Variables Information Number of Weld Passes 1 Welding Process [00] GMAW (Man) Operator Factor [%] 65 Electrode Brand Name Esab S-6 Solid Wire Electrode Classification AWS E70S-6 Type of Gas / Flux [G] Ar / 8-10% CO2 Deposition Efficiency [%] 91 Gas Flow or Flux Ratio [cfh or flux/wire] 40 Electrode Diameter [in] 0.045 Welding Voltage [volts] 30.0 Wire Feed Speed [in/min] 425 Electrode Stick-out [in] 0.75 Welding Current [amps] 300 Welding Travel Speed [in/min] 10.44 11.48 6.79 Theoretical Deposition Rate [lbs/hr] Actual Deposition Rate [lbs/hr] Consumable Cost Information Electrode Cost [$/lbs] Gas / Flux Cost [$/ft3 or $/lbs] Additional Information Pre-weld Time [min] Post-weld Time [min] Additional Variable Costs [$] New Procedure Total # of Weld Passes 1.33 0.03 17.00 45.00 3.00 Note : Numbers shown on this report are estimates only, any changes will modify the results 1 Process 1 1 Process 1 Procedure Variables Information Number of Weld Passes 1 Welding Process [30] MCAW (Man) Operator Factor [%] 65 Electrode Brand Name [3] Corex 6XC (Canada) Electrode Classification CSA E4801C-6-CH Type of Gas / Flux [G] Ar / 8-10% CO2 Deposition Efficiency [%] 97 Gas Flow or Flux Ratio [cfh or flux/wire] 40 Electrode Diameter [in] 0.062 Welding Voltage [volts] 28.0 Wire Feed Speed [in/min] 300 Electrode Stick-out [in] 1.00 Welding Current [amps] 310 Welding Travel Speed [in/min] 14.02 14.46 9. 1 1 Consumable Cost Information Electrode Cost [$/lbs] 1.67 Gas / Flux Cost [$/ft3 or $/lbs] Theoretical Deposition Rate [lbs/hr] Actual Deposition Rate [lbs/hr] 17.00 45.00 3.00 9.00 1.00 Additional Information Pre-weld Time [min] Post-weld Time [min] 9.00 Additional Variable Costs [$] 1.00 Substantial Savings! Weld Metal Deposition Summary Current Procedure Weld Consumable Usage Summary Electrode Consumed [lbs] Gas / Flux Consumed [ft3] Power Consumed [kwh] Procedure Cost New Procedure Cycle Time Joint Information Cycle Time Heat Input Summary Heat Input Summary Joint Type Total length of weld joint Weld Metal Deposited [lbs] Weld Metal Required by Weld Joint [lbs] Overweld (Underweld) Pre-weld Time [min] Total Welding Time [min] Post-weld Time [min] Cycle Time [min] Heat Input [kj/in] Pre & Post Weld Labor [$] Welding Labor [$] Total Electrode [$] Total Gas / Flux [$] Power [$] Additional Variable Expense(s) [$] Procedure / Process Total Cost Weld Metal Deposited [lbs] 14.60 Weld Metal Required by Weld Joint [lbs] 14.60 Overweld (Underweld) 0.0% Pre-weld Time [min] Post-weld Time [min] 9.00 Total Welding Time [min] 96.13 Cycle Time [min] 105.13 Heat Input [kj/in] 37.1 Weld Consumable Usage Summary Electrode Consumed [lbs] 15.05 Gas / Flux Consumed [ft3] 41.65 Power Consumed [kwh] 12.05 Procedure Cost Pre & Post Weld Labor [$] 11.25 Welding Labor [$] 120.16 Total Electrode [$] 25.14 Total Gas / Flux [$] Power [$] 0.96 Additional Variable Expense(s) [$] 1.00 Procedure / Process Total Cost $158.51 Note : Numbers shown on this report are estimates only, any changes will modify the results 96 Inch Loader Bucket : C Fillet - Flat 73 ft 77.50 161.36 21.35 1.68 1.34 3.00 $266.23 T o t a l 191.09 51.7 16.05 55.94 16.78 T o t a l 14.61 14.60 0.0% 17.00 129.09 45.00 $266.23 $158.51
Hobart Distributors To locate your nearest Hobart distributor call 1-937-332-4000 or 1-937-332-5188 or visit our Web site www.hobartbrothers.com Headquarters Hobart Brothers Company 101 Trade Square East Troy, OH 45373 Phone: 937-332-4000 Fax: 937-332-5700 International Headquarters Phone: 937-332-5188 FAX: 937-332-5064 Regional Office - Canada Canadian Welding Products Group Phone: (519)-537-6291 Fax: (519)-421-0480 Regional Office - Middle East Phone: +971-4299-6621 FAX: +971-4299-6681 E-mail: itwme@emirates.net.ae Regional Office - India Phone: +91-222520-7388 FAX: +91-222520-7389 E-mail: itwweldi@satyam.net.in Regional Office - Asia Phone: 65-6552-1223 FAX: 65-6552-1929 E-mail: vmarta@millerwelds.com Beijing Miller Electric Phone: +86-10-8739-7900 FAX: +86-10-8739-7600 E-mail: lisa.li@millerchina.com Regional Office - Brazil Phone: +55-11-5514-3366 FAX: +55-11-5891-7679 E-mail: itwsoldagem@osite.com.br Web site: www.itwsoldagem.com.br Regional Office - France Phone: +33-1-6004-1166 FAX : +33-1-6004-8860 E-mail: miller@itw-welding.fr Web site: www.miller-france.com Regional Office - Italy Phone: +39-02-9829-0218 FAX : +39-02-9828-1552 E-mail: millerit@itw-welding.it Regional Office - Netherlands Phone: +311-866-41456 FAX : +311-866-49020 E-mail: info@itw-welding.nl Web site: www.itw-welding.com Regional Office - Mexico Phone: +52-55-5366-7370 FAX : +52-55-5366-7376 E-mail: jflore@millerwelds.com Web site: www.itwweldingmexico.com Welding Industries of Australia Phone: +61-1300-300-884 FAX: +61-8-827-66327 E-mail: intc@welding.com.au Web site: www.welding.com.au Weldwell New Zealand Phone: +64-6-834-1600 FAX: +64-6-835-4568 E-mail: admin@weldwell.co.nz Web site: www.weldwell.co.nz Regional Office - Northern Europe Phone: 46-031-726-4600 FAX: 46-031-726-4700 E-mail: per.gelang@itw-welding.se Web site: www.elga.se Regional Office - Russia Phone: +7-812-961-5481 E-mail: infosvarka@itw-welding.ru Web site: www.itw-welding.ru Regional Office - Spain Phone: 34-963935398 FAX: 34-963629516 E-mail: vcubero@itw-welding.es Regional Office - Africa Phone: +44-7770562799 FAX: +44-1204-473039 E-mail: Andy.Foster@itw-welding.co.uk Web site: www.itw-welding.co.uk Regional Office for: Colombia, Venezuela, Trinidad & Tobago, Panama Phone: 920-968-7508 FAX: 920-735-4125 E-mail: mferna@millerwelds.com Ecuador, Peru, Bolivia, Chile, Argentina, Uruguay, Paraguay Phone: 920-968-7508 E-mail: mferna@millerwelds.com Guatemala, El Salvador, Honduras, Nicaragua, Costa Rica, Belize Phone: 525553667370 FAX: 525553667388 E-mail: ventas@itwwelding.com.mx Bahamas, Barbados, Dominican Republic, Jamaica, Puerto Rico, Virgin Islands Phone: 937-332-5188 FAX: 937-332-5064 E-mail: quafile@hobartbrothers.com Manufacturers: Tien Tai Electrode Co., LTD Phone: 886-6-2663721 Fax: 886-6-2664301 Web site: www.tientai.com Tien Tai Electrode (Kun Shan) Co. Phone: 86-51257446669 FAX: 86-51257448416 E-mail fuhu.chen@tientai.com.cn Web site: www.tientai.com Elga AB Phone: +46-31-726-46 00 FAX: +46-31-726-47-00 Web site: www.elgawelding.com
Hobart Brothers Company 101 Trade Square East Troy, OH 45373 www.hobartbrothers.com