Name of Parts 1. Drone Blade Guard Drone Body Blade Motor Body Light Camera Landing Gear Blade Guard Installation Diagram U8 TF Card Installation Diagram
. Transmitter Power Switch Throttle/ Up and Down Stick Rudder Trim Instruction of Screen Content 1 3 4 Video 180 Flip in Four Directions High/Medium/Low Speed Mode (Press Down) Indication Direction of Power Switch 11 5 6 10 9 Display Screen 7 Power Indicator Light Forward/Backward/ Left/Right Stick Left/Right Trim Forward/Backward Trim Notice: 1. Important Statement: (1) This product is not an ordinary toy but a piece of complicated equipment which is integrated with professional knowledge by mechanic, electronic, air mechanics, high-frequency emission etc., so it should be installed and adjusted correctly to avoid accidents. The user must always operate in a safe manner. We undertakes no liability for human injury or property damage caused by improper operation as we could not control the procedure of installation, use and operation of this drone. 8 Headless Mode (Press Down) Photo 360 Flip in Four Directions Indication Direction of Trim 1. Strong/Weak Emission Signal. Low Speed 3. Medium Speed (By Default) 4. High Speed 5. Video 6. Photo 7. Battery Indicator 8. Forward/Backward Trim Grid 9. Left/Right Trim Grid 10. Throttle Digital Display 11. Left/Right Rotation Trim Grid () This drone is suitable for experienced drone user aged 14 years or above. (3) The flying field must be legally approved by your local government. (4) We undertakes no liability for those accidents caused by improper operation, use and control of the drone after sale of the product. (5) We entrust the distributor to provide technology support and after-sale service. If you have any questions about use, operation, repair etc., please contact your local distributor.. Safety Precautions: Keep away from crowd when flying because a flying RC drone is very dangerous. Improper assembly, broken main frame, defective electronic equipment or unskilled operation all may cause unpredictable accidents such as drone damage or human injury. Please pay special attention to safety operation and have good knowledge of accident responsibility that the user may cause. (1) Keep away from obstacles and crowd The speed and status of a flying RC drone is uncertain and it may cause potential danger. So the user must keep away from crowd, tall building, power lines etc. when operating a flying RC drone. Do not fly a RC drone in rainy, storm, thunder and lighting weather for the safety of user, around people and their property. () Keep away from humid environment The drone inside is consisted of precise electronic components. Humidity or water vapor may damage electronic components and cause accident. (3) Safe operation Please operate the RC drone in accordance with your physical status and flying skill. Fatigue, listlessness and improper operation may increase the rate of accident. (4)Keep away from rotating parts Rotating Parts can cause serious injury and damage. Keep face and body away from rotating motors. (5) Keep away from heat The RC drone is made of metal, fiber, plastic, electronic components etc. Keep away from heat and sunshine to avoid distortion and damage. (6) Please do not touch the hot motor to avoid being burnt. 3. Check List Before Flight (1) Flying field must spacious enough and we suggest at least 8M (length)*8m (width)*5m (height). () Make sure the battery of the drone and its transmitter are fully charged. (3) Make sure the Throttle Control Stick of the transmitter in the lowest position. (4) Please strictly obey the order of turn on and turn off before operation. Turn on the transmitter power first and then turn on the drone power before flying; turn off the drone power first and then turn off the transmitter power when finish flying. Improper turn on and turn off order may cause the drone out of control and threaten people s safety. Please cultivate a correct habit of turn on and turn off. (5) Make sure the connection is solid between battery and motor etc. The ongoing vibration may cause bad connection of power terminal make the drone out of control. (6) Improper operation may cause drone crash, which may arouse motor defective and noise, and then effect the flying status or even stop flying. Please go to the local distributor to buy new parts for replacement so that the drone will return to its best status. 3 4
- - 1. Turn on the transmitter switch and the LED indicator begins to flash rapidly. Push the Throttle Stick all the way up then all the way down. The LED becomes flash slowly, which indicates the transmitter enters code pairing. - Frequency Pairing: Battery installation: open the battery cover on the back side of the transmitter and put 4 alkaline batteries (not included) into the box in accordance with electrode instructions. Transmitter Installation: 4*1.5V Alkaline Batteries. Install the battery to the mounted box and power on the drone. Notice: 1. Make sure the electrodes are correct.. Do not mixed use new and old batteries. 3. Do not mixed use new and old batteries. 4. Do not charge the non rechargeable battery. 3. Put the drone on the flat surface, the indicator light of the drone turns from flashing to solid bright. The drone is ready to be controlled. Important Notice: Please make sure the gyro of the receiving board is placed on the horizontal position after powering on the drone, so that the drone is ready for controlling. Charging Instruction 1. Connect the drone battery with USB charger first and then choose one of the methods in the below picture to connect with USB charger. (prior to choose A, 5V charger). Two red USB indicator lights keeps bright when charging. The charging time is about 45 minutes. The indicator lights turn to green when fully charged. (If the two indicator lights color become different, please do not use it to charge in case of the battery damage) 3. Li-Po battery is included in spare parts and please pay attention on below safe notice. * Never put the battery on a high temperature surface, or close to fire or heating devices to avoid damage or explosions. * Never use the battery to crash or hit hard surface. * Never put the battery in water and keep it in dry place. * Never open the battery. * Never leave the battery unsupervised during charging. * Make sure that there is no short circuit of the power wire. * Please use the recommended charger only. * Check the charger s wire, plug, surface regularly. Do not use any broken charger. Calibration Instruction Please follow below steps to calibrate the drone if the drone becomes imbalance after crashing during the flight, and can not be adjusted by trim button and cause difficult operation. 1. Turn off the drone switch, then turn off the transmitter power switch.. Turn on the transmitter switch, push the Throttle Stick all the way up then all the way down, and the transmitter enters pairing mode. 3. Power on the drone and put it on a flat surface in a horizontal position. You will hear di, di, di beeping noise three seconds later, which indicates successful code pairing. The drone body lights will turn solid. 4. Do not move the Throttle Stick before successful calibration. Push the Forward/Backward/ Left/Right Stick as shown below (See Picture 1). The drone body lights flash, which indicates that the drone is calibrating. When the drone body lights remain solid, turn over the drone and put it on the flat surface, repeat the operation to push the Forward/ Backward/Left/Right Stick as shown below (See Picture ). The drone body lights flash, which indicates that the drone is calibrating. When the drone body lights remain solid, your drone is ready to fly. Drone Battery LiPo Battery Disposal & Recycling Wasted Lithium-Polymer batteries must not be placed with household trash. Please contact local environmental or waste agency or the supplier of your model or your nearest LiPo battery recycling center. 5 Picture 1 Picture 6
Pre-Flight Operation: 7. If the drone rotates to the left or right 1. The camera is the drone front.. Power on the drone and check the direction of the rotating blades. The left front and right rear A blades rotating clockwise while the right front and left rear B blades rotating counterclockwise. 3. Adjust relative transmitter Trim button to adjust the rudder if the drone tilts to one side when flying. Press the Right Rotation Trim till balance if the drone rotates to the left, and press the Left Rotation Trim till balance if the the drone rotates to the right. Front A Blade Clockwise B Blade Counterclockwise Left Right B Blade Counterclockwise A Blade Clockwise Rear Flying Control High/Medium/Low Speed Mode By default, the drone is in Medium Speed Mode (M). Press the Throttle Stick and the transmitter issues sounds of dididi, which indicates that the drone enters High Speed Mode (H); Press the Throttle Stick again and the transmitter issues sounds of di, which indicates that the drone enters Low Speed Mode (L); Press the Throttle Stick one more time and the transmitter issues sounds of didi, which indicates that the drone enters Medium Speed Mode (M). High/Medium/Low Speed Mode Button (Press Down) Headless Mode 1. Push the Throttle Stick up to fly the drone up, and pull the Stick down to fly the drone down.. Push the Forward/Backward/Left/Right Stick to the left to fly the drone to the left, and pull the Stick to the right to fly the drone to ther right. Drones generally have a front and rear indicated by LED lights or colored blades. By default, the users are required to tell the front and the rear of the drone when flying. Under headless mode, the users can operate the drone without worrying about the orientation left is left and right is right all the time, regardless of where your drone is pointing at. Headless mode is designed for beginners and users who fly the drone in daylight or at a far distance. When the drone in Headless Mode, push the Right Stick to forward/backward/left/right, and the drone will fly to forward/backward/left/right accordingly. Forward Prerequisite: Position the drone in such a way that its front is your front (see Picture 1). Tip: Do not change the orientation of the transmitter (see Picture ) after entering headless mode. Backward 3. Push the Forward/Backward/Left/Right Stick up to fly the drone forward, and pull the Stick down to fly the drone backward. Front 4. Push the Throttle Stick to the left to rotate the drone to the left, and pull the Stick to the right to rotate the drone to the right. 5. If the drone tilts forward or backward Left Left Picture 1 Press the Right Trim till balance if the drone drifts to the left, and press the Left Trim till balance if the drone drifts to the right. Drift Right 7 Right Rear Tilt backward 6. If the drone tilts to the left or right Drift left Right Rear Press the Backward Trim till balance if the drone drifts forward, and press the Forward Trim if the drone drifts backward. Tilt forward Front Picture To turn on headless mode, press the headless mode button and the drone LED lights flashes, which indicates the headless mode is ready. To turn off headless mode, press the headless mode button again and the drone LED lights turns solid, which indicates the headless mode is off. 8
180 and 360 Flip How to view the data saved in TF card 180 Flip (Standard Flight or Inverted Flight) Turn off the drone switch first when finish aerial photography. Take out TF card and insert the card to a card reader. Connect the card reader with computer USB port. After a while, view the aerial photography data from my computer - mobile disk. When the drone is flying, press the right button on the back side of the transmitte, the transmitter will issue sound of dididi..., and then push the Forward/Backward/Left/Right Stick to Forward/Backward/Left/Right. The drone will do 180 flipping to forward or backward or left or right synchronously. 180 Flip Button Tip: Please play the video or photo after coping all aerial photography data to computer and make sure the play software can support its format. Basic parameter for aerial camera: Video DPI 180*70P/30FPS; Image Size 180*70P. Spare Parts For convenience, the spare parts are listed for you to choose, which can be purchased from the local distributor. (The circled icon please refer to the exploded view below) 360 Flip Press the left button on the back side of the transmitter when the drone is flying, and the transmitter will issue sounds of dididi..., and then push the Forward/Backward/Left/Right Stick to Forward/Backward/Left/Right. The drone will do 360 flipping to forward or backward or left or right synchronously. 360 Flip Button Installation and Replacement for Blade 1. Put the attached spanner between the motor and the blade like Picture 1 as below, and then press the spanner to lift up and remove the blade as Picture. Picture 1 Picture Picture 3 Picture 4. Press the blade to the motor axis as Picture 3. Keep the blade perpendicular to the motor axis as Picture 4. (choose the correct blade--counterclockwise or clockwise) 9 U8-01 Upper Cover U8-0 Lower Cover U8-03 Blade U8-04 Blade Guard U8-05 Landing Gear U8-06 Camera Cover U8-07 U8-08 Battery Holder U8-09 USB Cable U8-10 Li-Po Battery U8-11 Clockwise Motor (Red and Blue Wire) U8-1 Counterclockwise Motor (Black and White Wire) U8-13 Receiving Board U8-14 Circuit Board for Camera U8-15 Transmitter U8-16 TF card U8-17 Card Reader U8-18 Camera Acrylic U8-19 Iron Axis for U8-0 Spanner 10
Exploded View Troubleshooting Guide No. Problem Problem Cause Solution 1. The transmitter battery is too low. 1. Replace battery. 1 The transmitter indicator light is off. The battery positive pole and negative pole are in reverse order. 3. Poor Contact.. Install the battery in accordance with the user manual. 3. Clean the dirt between the battery and the battery alice. 1. Indicator light is off. 1. The same as above 1..3. Fail to pair the drone with transmitter. There is interfering signal nearby. 3. Misoperation.. Restart the drone and power on the transmitter. 3. Operate the drone step by step in accordance with the user manual. 4. The electronic component is damaged for frequent crash. 4. To buy spare parts from local seller and replace damaged parts. 3 The drone is underpowered or can not fly. 1. The blade deformed seriously. 1. Replace blade.. The drone battery is too low.. Recharge the drone battery. 3. Incorrect installation of blade. 3. Install the blade in accordance with the user manual instruction. 1. The blade deformed seriously. 1. Replace blade. 4 The drone can not hover and tilts to one side. The motor holder deformed and out of verticality. 3. The gyro did not reset after violent crash.. Replace the motor holder. 3. Put the drone on the flat ground for about 10s or restart the the drone to calibrate again. 4. The motor is damaged. 4. Replace motor. 1. The drone battery is too low. 1. Recharge the drone battery. No. 1 Name A Blade (Colockwise) Clockwise Motor No. 11 1 Name Lower Cover Right Landing Gear 5 The drone indicator light is off. The battery is expired or overdischarge protection. 3. Poor contact.. Buy a new battery from local seller to replace or recharge the battery. 3. Disconnect the battery and then connect it with the plug again. 3 Tail Light (Red) 13 Camera Cover 4 Upper Cover 14 Camera Acrylic 5 B Blade (Counterclockwise) 15 Circuit Board for Camera 6 Right Blade Guard 16 Left Blade Guard 7 Counterclockwise Motor 17 8 Front Light (Green) 18 Battery Holder 9 Receiving Board 19 TF Card 10 Battery 0 Left Landing Gear 11 1