News TECHNOLOGY RAPI-tec innovation Repair and reconstruction of concrete pavements Very fast opening to traffic (3-6 hours) Maximal durability in time. Your internal or external floors have deteriorated and need Fast, Economical and Durable Repair? May 2013 Contact us for an inspection. Our specialists are at your disposal to propose : a personalised proposal for a time-certain and fast applied and re-usable pavement.. Logistic Platforms Freight areas - Deposits - Airports Helicopter platforms - Hangar - Port Areas Parkings - Factories - Shops - Shopping Malls - Aprons - Floors in Concrete, roofs and between levels RAPI-tec Faster, Stronger, Durable, No Shrinkage RAPI-tec aeroslab (screed/concrete) RAPI-tec pav (mortar) RAPI-tec self injection (slurry) RAPI-tec ramp 1 (ramps) RAPI-tec stone (exposed aggregate) Advantages of the RAPI-tec system: - Maximum Efficiency in Technology of Installation without interruption in Commercial and Industrial Activities - Total Package Product Management + Installation - Rapid Execution associated with a rapid hardening and opening to traffic - Resistance, No shrinkage, Durability
- Maximal saving in cost en time!!! - Economic advantages on short and long term!!! Which are the RAPI-tec systems? Pre-mix with innovative nano-technology with very high performance belonging to the family of : HPC High Performance Concretes HPFRC High Performance Fibre Reinforced Concretes Almost all the floors have phenomena: superficial or deep damage - Flaking of quartz particles or 'dusting' - cracks after a few months - Contraction Joints Opening and gaping - uncertain coplanarity between the frames... often as consequence the awkward and precarious driving safety for both the driver and the handling and storage of goods. Systems RAPI-tec, Specially Formulated for Rapid Hardening and taking in service in the reconstruction, repair and finishing of concrete floors, allow: Fast Safe Durable Repair - Volumetric Stability with Technology SHRINKO-tec anti-cracking - Quick opening to Pedestrians (1 hours) and the general traffic (3-6 hours) - Maximum wear Resistance - Resistance to shock - Diversification of Functional Solutions, Aesthetic, Colours. RAPI-tec systems allow optimal intervention thickness of 6-10 mm minimum up to 10 cm and more. RAPI-tec aeroslab, for rapid hardening screeds and concretes,allow almost each thickness of application up 40 cm. The correct diagnostic approach on the quality of support, resulting in the proper preparation of the substrate itself and application of RAPI-tec, the prestigious successes have led to: Elimination of Cracks - Total and Partial Elimination of dilatation Joints Restoration of the planarity - no Delaminations - Elimination of dusting - wear reduced by 80% - Excellent Durability.
Tecnochem RAPI-tec : Logistic Platforms Freight areas - Deposits - Airports Helicopter platforms - Hangar - Port Areas-Parkings - Factories - Shops - Shopping Malls - Aprons - Floors in Concrete, roofs and between levels Repair of a industrial and commercial floors RAPI-tec pav 2 RA
Repair of a concrete floorslab on the roof of commercial center and warehouse RAPI-tec pva/pav R1 ST-HS Joint reconstruction of degraded concrete Airport or Industrial pavements. RAPI-tec pva/pav MC or RAPI-tec pva/pav R1 ST-HS Reconstruction of concrete runway slabs, opening to air-traffic only 3 hours after the casting (25 MPa) Airport of Zurich RAPI-tec aeroslab
Fixating or the runway lights with RAPI-tec self injection Concrete floor degraded by thermal shock by the heat of the reactors tested + frost /thaw damage. RAPI-tec pva/pav R1 ST-HS
Tecnochem RAPI-tec : Possible different types of finishing and coloring Multi-story garage floor with RAPI-tec pav + Finish with epoxy coating TECNOEPO FLOORING SYSTEM 185 Tecnochem RAPI-tec ramp 1: formulated for trafficed ramps open for foot traffic after 1-2 hours light traffic after 6 hours
Tecnochem RAPI-tec stone: Surfaces with aggregate exposed - quickly polished surfaces
RAPI-tec : Resistance to different types of traffic and stresses.
RAPI-tec pav : Tools for mixing and application 1) MIXING (alternatives) Vertical axes Paddle Pan Mixer Bigger mixer with incorporated pump (RAPI-tec pav 2 RA)
2) TRANSPORT (alternatives) Wheelbarrow Extension tubes 3) TOOLS Rake, Trowel, Shovels
Vibrating rule Levelling tool bull floating Helicopter (RAPI-tec pav 2 RA)
Extracts from technical data sheets RAPI-tec PAV Technical Characteristics (typical values) RAPI-tec pav 2/RA RAPI-tec pva/pav R1/ST-HS Maximum grain size 2 mm 2 mm Initial setting time (20 C) DPU 100 minutes 60 minutes Final setting time (20 C) 90-120 minutes 90 minutes Density 2,3 Kg/litre 2,3 Kg/litre Consumption 2,3 Kg/ m 2 /mm 2,1 Kg/ m 2 /mm Compressive strength 5 hours 24 hours 7 days 28 days Flexural strength 5 hours 24 hours 7 days 28 days 12 MPa 22 MPa 53 MPa 71 MPa 3.9 MPa 5.1 MPa 8.9 MPa 12.2 MPa 20 MPa 40 MPa 78 MPa 96 MPa 3.9 MPa 11 MPa 20 MPa 24 MPa Elasticity Modulus (28 days) 30 GPa 36 GPa. Fracture Energy (28 days) 150 N/m 10.000 N/m Water permeability EN 12390-8 5 bar x 3 days Resistance to frost/thaw in presence of chlorides according to SIA 162 (Suisse Standard) : after 28 cycles 600gr/m 2 corresponds to optimal resistance Shrinkage/expansion (free) (T = 20 C R.H. = 50%) (UNI EN 12617-4 / UNI 6687-73) Adhesion to the substrate ( EN 1504 3 ) < 3 mm < 3 mm 180 gr/m 2 180 gr/m 2-190µ a t90 days 3 MPa at 28 days (substrate failure) ± 10 µ/m at 90 days 3 MPa at 28 days (substrate failure) Impact resistance (CSTB 3232) No cracks after 25 impacts No cracks after 25 impacts Surface hardness (EN 13892-6) 150 N/mm 2 150 N/mm 2 Shore hardness (ISO 868) D 75 D 75 Penetration test (EN 12697-21) I < 0,1 mm I < 0,1 mm Wear resistance (to rolling wheel) (XP P 11-101) v r 2 cm 3 v r 2 cm 3 Resistance to deep abrasion (EN 102) 20 mm 3 20 mm 3 Sulphate resistant UNI EN 196/1 and ASTM C 88 (sequence of 15 immersions and curing in a solution of magnesium sulphate) Resistance to chemical agents (contact time : 24 hours) No damage Loss of weight < 0,20% No change in the substrate with caustic soda, amines, methanol, trichloroethylene, gasoline, motor oil, brake fluid. No damage Loss of weight < 0,20% No change in the substrate with caustic soda, amines, methanol, trichloroethylene, gasoline, motor oil, brake fluid.. Extract from technical data sheet RAPI-tec aeroslab/conc components concrete Kg/m 3 screed Kg/m 3 RAPI-tec aeroslab/conc 500 550 Aggregates 0,1-16 mm 1790 0 Aggregates 0,1-10 mm (can be also supplied by us) 0 1750 FIBRE-tec EST 7 7 Ratio of active W/C 0,35 0,35 Consistency S4-S5 S4-S5 Pot life a 20 C 25 min. Initial setting at 20 C 30 min. Specific weight 2.430 kg/m 3 Compressive strength after 3 hours 24 MPa Compressive strength after 28 days 75 MPa Flexural strength after 28 days 8 MPa Elasticity Modulus after 28 days 38 GPa Fracture Energy after 28 days ~ 500 N/m Spalling after 28 cycles of frost/thaw with chlorides 80 g/m 2 Extract from technical data sheet RAPI-tec self/injection Mixing water 32% Wet density 2.004 gr/lt Fluidity Marsh (Ø opening=12 mm / 1 litre) 15 40 sec. Initial spreading 406% Spreading after 20 minutes 393% End of setting 35 minutes Compressive strength after 3 hours 31 MPa Flexural strength after 3 hours 6 MPa Compressive strength after 24 hours 45 MPa Flexural strength after 24 hours 8 MPa Compressive strength after 28 days 58 MPa Flexural strength after 28 days 13 MPa Dynamic elasticity modulus after 28 days 26.500 MPa Static elasticity modulus after 28 days 16.500 MPa Adhesion to concrete > 2 MPa Freeze/thaw resistance in presence of chlorides according to SIA 162 specification of the Swiss Motorway Authorities - after 28 cycles 600 g/m² 190 gr/m 2 corresponds to excellent frost resistance with salts Free shrinkage/expansion : substrate saturated with water, protected after 24 h after 90 d +100 µ/m +150 µ/m (UNI EN 12617-4 / UNI 6687-73) Consumption : approx. 1,4 Kg/lt
Tecnochem RAPI-tec : When each minutes counts! Sequence of operation : - Preparation of the surface with scarification - Remove debris and dust extraction - High pressure water jetting and water saturation - Extraction of stagnant water - Mixing minimum 7 minutes! until homogeneous - Application direct by barrows or pump - Leveling with bull float or vibrating rule - Finishing with "bull floating" or, alternatively depending on the applications, with helicopter - Anti-evaporation Protection in function of environmental conditions and exposure - Light foot traffic after 1-2 hours - Open to traffic after 3-6 hours for light traffic Tecnochem: - Assistance from Project to Jobsite - Engineering and Product Management + Application Consult also the Technical datasheets of the products in: www.edilportale.com Requests for information and/or assistance : Send e-mail to the Office for Project Promotion and Assistance uapp@tecnochem.it Pls consult our web-site www.tecnochem.it TECNOCHEM ITALIANA SPA - Via Sorte 2/4-24030 Barzana (BG) www.tecnochem.it - uapp@tecnochem.it