This stock catalog contains the sizes, weights and descriptions of all standard Steel, Brass, Bronze and Dura-Bar Cast Iron items that are available from stock for immediate delivery. However, new items are continually being added. It is our intent to always maintain the highest level of quality metals obtainable from our mill sources. Call PETERSON STEEL first for your requirements on the following items: CDA 932 BEARING BRONZE OILITE BRONZE FLAT GROUND STOCK THREADED ROD CARBON STEEL STRESSPROOF STEEL ALLOY STEEL TG&P SHAFTING METRIC TG&P SHAFTING DRILL ROD HOT ROLLED ANGLES & CHANNELS BRASS TOOL STEEL STRIPPER PLATE STAINLESS STEEL CDA 954 ALUMINUM BRONZE EXCLUSIVE NEW ENGLAND DISTRIBUTOR FOR DURA-BAR CONTINUOUS CAST IRON BAR PRODUCTS AUTOMATIC SAW CUTTING FACILITIES UP TO 32" DIAMETER Your inquiries on standard as well as non-standard items are invited. PETERSON STEEL CORPORATION P.O. Box 60328, Greendale Station, 61 West Mountain St., Worcester, MA 01606-0328 (508) 853-3630 (800) 325-3245 fax (508) 853-7485 www.petersonsteel.com 5/09
Table of Contents Carbon Steel Cold Finished Flats...1 Cold Finished Rounds...9 Stressproof...13 Cold Finished Hexagons...14 Cold Finished Squares...16 T G & P Shafting...18 D G & P Accuracy Stock...19 Metric T G & P Shafting...19 Forged & Rough Turned Rounds...20 Hot Rolled Rounds...21 Hot Rolled Angles...22 Hot Rolled Channels...23 Threaded Rod...24 Alloy Steel Cold Finished Rounds...24 T G & P Shafting...25 Cold Finished Squares & Hexagons...26 Hot Rolled Rounds...27 Forged & Rough Turned Rounds...30 Stainless Steel Rounds...31 Squares...32 Flats...33 Brass Rounds...34 Flats...35 Hexagons...36 Squares...37
Table of Contents Dura-Bar Cast Iron Product Data...39 Gray Iron Rounds...45 Gray Iron Tubes...46 Gray Iron Flats...48 Gray Iron Squares...49 Stress Relieved Plate...50 Ductile Iron Rounds...51 Bearing Bronze CDA 932 Tubes...53 CDA 932 Rounds...56 CDA 932 Plate...57 Aluminum Bronze CDA 954 Rounds...58 CDA 954 Flats & Squares...59 Drill Rod...60 S/R Stripper Plate...61 Color Codes...63
Decimal Equivalents Chart 1/64.015625 1/32.03125 3/64.046875 1/16.0625 5/64.078125 3/32.09375 7/64.109375 1/8.125 9/64.140625 5/32.15625 11/64.171875 3/16.1875 13/64.203125 7/32.21875 15/64.234375 1/4.25 17/64.265625 9/32.28125 19/64.296875 5/16.3125 21/64.328125 11/32.34375 23/64.359375 3/8.375 25/64.390625 13/32.40625 27/64.421875 7/16.4375 29/64.453125 15/32.46875 31/64.484375 1/2.5 33/64.515625 17/32.53125 35/64.546875 9/16.5625 37/64.578125 19/32.59375 39/64.609375 5/8.625 41/64.640625 21/32.65625 43/64.671875 11/16.6875 45/64.703125 23/32.71875 47/64.734375 3/4.75 49/64.765625 25/32.78125 51/64.796875 13/16.8125 53/64.828125 27/32.84375 55/64.859375 7/8.875 57/64.890625 29/32.90625 59/64.921875 15/16.9375 61/64.953125 31/32.96875 63/64.984375 1 1. i
C-1018 Cold Finished Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 1/16 x 1/4.0531 3/8.0797 1/2.1063 5/8.1328 3/4.1594 7/8.1859 1-0/0.2125 1-1/4.2656 1-1/2.3188 2-0/0.4250 1/8 x 3/16.0797 1/4.1063 5/16.1328 3/8.1594 7/16.1859 1/2.2125 9/16.2391 5/8.2656 3/4.3188 7/8.3719 1-0/0.4250 1-1/8.4781 1-1/4.5313 1-3/8.5843 1-1/2.6375 1-3/4.7438 2-0/0.8500 2-1/4.9563 2-1/2 1.063 2-3/4 1.169 3-0/0 1.275 3-1/4 1.381 3-1/2 1.488 4-0/0 1.700 4-1/2 1.913 5-0/0 2.125 6-0/0 2.550 3/16 x 1/4.1594 5/16.1992 3/8.2391 7/16.2789 1/2.3188 9/16.3586 5/8.3984 3/4.4781 7/8.5578 1-0/0.6375 1-1/8.7172 1-1/4.7969 1-3/8.8766 1-1/2.9563 1-3/4 1.116 1-7/8 1.195 2-0/0 1.275 2-1/4 1.434 2-1/2 1.594 2-3/4 1.753 3-0/0 1.913 3-1/4 2.072 3-1/2 2.231 4-0/0 2.550 4-1/2 2.869 5-0/0 3.188 6-0/0 3.825 7-0/0 4.462 8-0/0 5.100 10-0/0 6.375 12-0/0 7.650 1/4 x 5/16.2656 3/8.3188 All material will conform to ASTM A 108. 1
C-1018 Cold Finished Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 1/4 x 7/16.3719 1/2.4250 9/16.4781 5/8.5313 3/4.6375 7/8.7438 1-0/0.8500 1-1/8.9563 1-1/4 1.063 1-3/8 1.169 1-1/2 1.275 1-5/8 1.381 1-3/4 1.488 1-7/8 1.594 2-0/0 1.700 2-1/4 1.913 2-1/2 2.125 2-3/4 2.338 3-0/0 2.550 3-1/4 2.763 3-1/2 2.975 3-3/4 3.188 4-0/0 3.400 4-1/4 3.613 4-1/2 3.825 5-0/0 4.250 5-1/2 4.675 6-0/0 5.100 7-0/0 5.950 8-0/0 6.800 9-0/0 7.650 10-0/0 8.500 11-0/0 9.350 12-0/0 10.20 14-0/0 11.89 5/16 x 3/8.3984 7/16.4648 1/2.5313 5/8.6641 3/4.7969 7/8.9297 1-0/0 1.063 1-1/8 1.195 1-1/4 1.328 1-3/8 1.461 1-1/2 1.594 1-3/4 1.859 2-0/0 2.125 2-1/4 2.391 2-1/2 2.656 2-3/4 2.922 3-0/0 3.188 3-1/2 3.719 4-0/0 4.250 4-1/2 4.781 5-0/0 5.313 6-0/0 6.375 8-0/0 8.500 10-0/0 10.63 12-0/0 12.75 3/8 x 7/16.5578 1/2.6375 9/16.7172 5/8.7969 3/4.9563 7/8 1.116 1-0/0 1.275 1-1/8 1.434 1-1/4 1.594 All material will conform to ASTM A 108. 2
C-1018 Cold Finished Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 3/8 x 1-3/8 1.753 1-1/2 1.913 1-5/8 2.072 1-3/4 2.231 1-7/8 2.391 2-0/0 2.550 2-1/4 2.869 2-1/2 3.188 2-3/4 3.506 3-0/0 3.825 3-1/4 4.144 3-1/2 4.463 3-3/4 4.781 4-0/0 5.100 4-1/2 5.738 5-0/0 6.375 5-1/2 7.013 6-0/0 7.650 6-1/2 8.287 7-0/0 8.925 8-0/0 10.20 9-0/0 11.48 10-0/0 12.75 11-0/0 14.03 12-0/0 15.30 14-0/0 17.85 7/16 x 1/2.7437 5/8.9296 3/4 1.116 7/8 1.302 1-0/0 1.488 1-1/4 1.859 1-1/2 2.231 1-3/4 2.603 7/16 x 2-0/0 2.975 2-1/4 3.347 2-1/2 3.719 3-0/0 4.462 3-1/2 5.206 4-0/0 5.950 4-1/2 6.693 5-0/0 7.437 6-0/0 8.925 1/2 x 9/16.9562 5/8 1.063 11/16 1.169 3/4 1.275 7/8 1.486 1-0/0 1.700 1-1/8 1.913 1-1/4 2.125 1-3/8 2.338 1-1/2 2.550 1-5/8 2.763 1-3/4 2.975 2-0/0 3.400 2-1/4 3.825 2-1/2 4.250 2-3/4 4.675 3-0/0 5.100 3-1/4 5.525 3-1/2 5.950 3-3/4 6.375 4-0/0 6.800 4-1/4 7.225 4-1/2 7.650 4-3/4 8.075 5-0/0 8.500 5-1/2 9.350 5-3/4 9.775 All material will conform to ASTM A 108. 3
C-1018 Cold Finished Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 1/2 x 6-0/0 10.20 6-1/2 11.05 7-0/0 11.90 8-0/0 13.60 9-0/0 15.30 10-0/0 17.00 11-0/0 18.70 12-0/0 20.40 14-0/0 23.80 9/16 x 5/8 1.195 3/4 1.434 7/8 1.673 1-0/0 1.912 1-1/4 2.391 1-1/2 2.869 2-0/0 3.825 2-1/2 4.781 5/8 x 3/4 1.594 7/8 1.859 1-0/0 2.125 1-1/8 2.391 1-1/4 2.656 1-3/8 2.922 1-1/2 3.187 1-5/8 3.453 1-3/4 3.719 2-0/0 4.250 2-1/4 4.781 2-1/2 5.313 2-3/4 5.844 3-0/0 6.375 3-1/4 6.906 3-1/2 7.438 3-3/4 7.968 4-0/0 8.500 5/8 x 4-1/2 9.563 5-0/0 10.63 5-1/2 11.69 6-0/0 12.75 7-0/0 14.88 8-0/0 17.00 9-0/0 19.13 10-0/0 21.25 12-0/0 25.50 14-0/0 29.75 3/4 x 7/8 2.231 1-0/0 2.550 1-1/8 2.869 1-1/4 3.188 1-3/8 3.506 1-1/2 3.825 1-5/8 4.144 1-3/4 4.463 2-0/0 5.100 2-1/4 5.738 2-1/2 6.375 2-3/4 7.013 3-0/0 7.650 3-1/4 8.288 3-1/2 8.925 3-3/4 9.562 4-0/0 10.20 4-1/2 11.48 5-0/0 12.75 5-1/2 14.03 All material will conform to ASTM A 108. 4
C-1018 Cold Finished Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 3/4 x 6-0/0 15.30 6-1/2 16.57 7-0/0 17.85 8-0/0 20.40 9-0/0 22.95 10-0/0 25.50 11-0/0 28.04 12-0/0 30.60 14-0/0 35.70 7/8 x 1-0/0 2.975 1-1/8 3.347 1-1/4 3.719 1-3/8 4.091 1-1/2 4.463 1-3/4 5.206 2-0/0 5.950 2-1/4 6.694 2-1/2 7.438 2-3/4 8.181 3-0/0 8.925 3-1/2 10.41 4-0/0 11.90 4-1/2 13.39 5-0/0 14.88 6-0/0 17.85 8-0/0 23.80 10-0/0 29.75 12-0/0 35.70 1 x 1-1/8 3.825 1-1/4 4.250 1-3/8 4.675 1-1/2 5.100 1-5/8 5.525 1-3/4 5.950 2-0/0 6.800 2-1/4 7.650 2-1/2 8.500 2-3/4 9.350 All material will conform to ASTM A 108. 1 x 3-0/0 10.20 3-1/4 11.05 3-1/2 11.90 3-3/4 12.75 4-0/0 13.60 4-1/2 15.30 5-0/0 17.00 5-1/2 18.70 6-0/0 20.40 6-1/2 22.10 7-0/0 23.80 8-0/0 27.20 9-0/0 30.60 10-0/0 34.00 12-0/0 40.80 14-0/0 47.60 1-1/8 x 1-1/4 4.781 1-3/8 5.259 1-1/2 5.737 1-5/8 6.215 1-3/4 6.693 2-0/0 7.650 2-1/4 8.606 2-1/2 9.563 3-0/0 11.48 4-0/0 15.30 6-0/0 22.95 1-1/4 x 1-3/8 5.844 1-1/2 6.375 1-5/8 6.906 1-3/4 7.438 2-0/0 8.500 2-1/4 9.563 2-1/2 10.63 2-3/4 11.69 3-0/0 12.75 3-1/4 13.81 3-1/2 14.88 3-3/4 15.94 5
C-1018 Cold Finished Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 1-1/4 x 4-0/0 17.00 4-1/2 19.13 5-0/0 21.25 5-1/2 23.38 6-0/0 25.50 7-0/0 29.75 8-0/0 34.00 10-0/0 42.50 12-0/0 51.00 14-0/0 59.50 1-3/8 x 1-1/2 7.013 2-0/0 9.350 3-0/0 14.03 1-1/2 x 1-5/8 8.288 1-3/4 8.925 2-0/0 10.20 2-1/4 11.48 2-1/2 12.75 2-3/4 14.03 3-0/0 15.30 3-1/4 16.58 3-1/2 17.85 4-0/0 20.40 4-1/2 22.95 5-0/0 25.50 5-1/2 28.05 6-0/0 30.60 7-0/0 35.70 8-0/0 40.80 10-0/0 51.00 12-0/0 61.20 14-0/0 71.40 All material will conform to ASTM A 108. 1-5/8 x 2-0/0 11.05 2-1/2 13.81 3-0/0 16.58 4-0/0 22.10 1-3/4 x 2-0/0 11.90 2-1/4 13.39 2-1/2 14.88 2-3/4 16.36 3-0/0 17.85 3-1/2 20.83 3-3/4 22.31 4-0/0 23.80 4-1/2 26.78 5-0/0 29.75 6-0/0 35.70 8-0/0 47.60 10-0/0 59.50 12-0/0 71.40 2 x 2-1/4 15.30 2-1/2 17.00 2-3/4 18.70 3-0/0 20.40 3-1/4 22.10 3-1/2 23.80 4-0/0 27.20 4-1/2 30.60 5-0/0 34.00 6-0/0 40.80 7-0/0 47.60 8-0/0 54.40 9-0/0 61.20 10-0/0 68.00 12-0/0 81.60 14-0/0 95.20 6
C-1018 Cold Finished Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 2-1/4 x 2-1/2 19.13 3-0/0 22.95 3-1/4 24.86 3-1/2 26.78 4-0/0 30.60 4-1/2 34.43 5-0/0 38.25 6-0/0 45.90 8-0/0 61.20 10-0/0 76.50 12-0/0 91.80 2-1/2 x 2-3/4 23.38 3-0/0 25.50 3-1/2 29.75 4-0/0 34.00 4-1/2 38.25 5-0/0 42.50 6-0/0 51.00 7-0/0 59.50 8-0/0 68.00 10-0/0 85.00 12-0/0 102.0 3 x 3-1/2 35.70 4-0/0 40.80 4-1/2 45.90 5-0/0 51.00 6-0/0 61.20 8-0/0 81.60 10-0/0 102.0 12-0/0 122.4 3-1/2 x 4-0/0 47.60 6-0/0 71.40 7-0/0 85.10 8-0/0 97.16 10-0/0 121.3 12-0/0 145.4 4 x 4-1/2 61.20 5-0/0 68.00 6-0/0 81.60 8-0/0 108.8 10-0/0 138.4 12-0/0 166.0 4-1/2 x 5-0/0 76.50 5 x 5-1/2 93.50 6-0/0 102.0 8-0/0 136.0 10-0/0 173.2 12-0/0 206.0 6 x 8-0/0 163.2 10-0/0 206.7 12-0/0 247.0 All material will conform to ASTM A 108. Some of the larger sizes are milled from plate and could be.015" to.050" OVERSIZE. 7
C-1018 Cold Finished Flats 10/12' Lengths PRODUCT DATA Tolerances C-1018 Cold Finished Steel Flats (Tolerances apply to thickness as well as width) Width in inches Undersize variation To 3/4 incl..003 Over 3/4 to 1-1/2 incl..004 Over 1-1/2 to 3 incl..005 Over 3 to 4 incl.006 Over 4 to 6 incl..008 Over 6.013 All material will conform to ASTM A 108. 8
Carbon Steel Cold Finished Rounds 10/12' Lengths Size Wt/Ft Wt/12' 1018 1214L 1144SP Other 1/8.042.500 S S... 1008 5/32.065.782... S...... 3/16.094 1.13 S S...... 7/32.128 1.53... S...... 1/4.167 2.00 S S... 1215 9/32.211 2.54... S...... 5/16.261 3.13 S S... 1215 11/32.316 3.79... S...... 3/8.376 4.51 S S S... 13/32.441 5.29... S...... 7/16.511 6.13 S S...... 15/32.587 7.04... S...... 1/2.668 8.01 S S S 1215 9/16.845 10.1 S S S... 5/8 1.04 12.5 S* S S... 11/16 1.26 15.1 S S S... 3/4 1.50 18.0 S* S S 1215 13/16 1.76 21.2 S S S... 7/8 2.05 24.5 S* S S... 29/32 2.19 26.3... S...... 15/16 2.35 28.2 S* S S... 31/32 2.51 30.1... S...... 1 2.67 32.0 S* S S 1215 1-1/16 3.02 36.2 S S S 1117L 1-1/8 3.38 40.6 S* S S 1215 1-3/16 3.77 45.2 S* S S 1215 1-1/4 4.17 50.1 S* S S... 1-5/16 4.60 55.2... S...... 1-3/8 5.05 60.6 S* S S 1215 & 1141 1-7/16 5.52 66.2 S* S...... S* = stocked in 20'/24' lengths. All material will conform to ASTM A 108. 9
Carbon Steel Cold Finished Rounds 10/12' Lengths Size Wt/Ft Wt/12' 1018 1214L 1144SP Other 1-1/2 6.01 72.1 S* S S... 1-9/16 6.52 78.2... S S... 1-5/8 7.05 84.6 S* S S 1117 1-11/16 7.60 91.3 S* S... 1215 1-3/4 8.18 98.1 S* S S... 1-13/16 8.77 105... S S... 1-7/8 9.39 113 S* S S 1117L & 1141 1-15/16 10.0 120 S* S...... 2 10.7 128 S* S S... 2-1/16 11.4 136... S...... 2-1/8 12.1 145 S* S S 1117L & 1215 2-3/16 12.8 153 S* S... 1117L 2-1/4 13.5 162 S* S S 1215 2-5/16 14.3 171... S...... 2-3/8 15.1 181 S* S S 1215 2-7/16 15.9 190 S* S...... 2-1/2 16.7 200 S* S S 1215 2-5/8 18.4 221 S* S S 1215 2-11/16 19.3 232 S*......... 2-3/4 20.2 242 S* S S 1215 2-7/8 22.1 265 S* S... 1215 & 1117L 2-15/16 23.0 277 S* S...... 3 24.0 288 S* S S 1215 3-1/16 25.1 301... S... 1215 3-1/8 26.1 313 S* S... 1215 3-1/4 28.2 339 S* S... 1215 3-3/8 30.4 365 S* S S 1215 3-1/2 32.7 393 S* S S 1141 3-5/8 35.1 421... S S... 3-3/4 37.6 451 S* S... 1117L S* = stocked in 20'/24' lengths. All material will conform to ASTM A 108. 10
Carbon Steel Cold Finished Rounds 10/12' Lengths Size Wt/Ft Wt/12' 1018 1214L 1144SP Other 3-7/8 40.1 481......... 1215 4 42.7 513 S* S S 1117 4-1/8 45.4 545... S...... 4-1/4 48.2 579 S* S...... 4-3/8 51.1 613......... 1215 4-1/2 54.1 649 S* S S 1215 4-3/4 60.3 723 S* S N/A... 5 66.8 801 S* S N/A... 5-1/4 73.6 883 S* S N/A... 5-1/2 80.8 969 S* S N/A... 5-3/4 88.3 1060 S* S N/A 1117L 6 96.1 1154 S* S N/A 1215 & 1117L 6-1/4 104 1252 S* S N/A... 6-1/2 113 1354 S* S N/A... 6-3/4 122 1460 S* S N/A... 7 131 1570 S* S N/A 1117L 7-1/4 141 1685 S* S N/A... 7-1/2 150 1802 S* S N/A... 7-3/4 160 1925 S* S N/A... 8 171 2052 S* S N/A... 8-1/2 193 2317 S* S N/A... 9 216 2596 S S N/A... 9-1/2 241 2892 S S N/A... 10 268 3216 S S N/A... 11 323 3876 S S N/A... 12 385 4620 S S N/A... S* = stocked in 20'/24' lengths. All material will conform to ASTM A 108. 11
Carbon Steel Cold Finished Rounds 10/12' Lengths PRODUCT DATA Tolerances Round Cold Drawn or Turned & Polished Carbon Steel Bars (Minus tolerances in inches) Maximum Maximum Carbon Range Carbon Range of over.28% Specified Size in Inches.28% or less to.55% incl Up to 1-1/2 incl. 0.002 0.003 Over 1-1/2 to 2-1/2 incl. 0.003 0.004 Over 2-1/2 to 4 incl. 0.004 0.005 Over 4 to 6 incl. 0.005 0.006 Over 6 to 8 incl. 0.006 0.007 Over 8 to 9 incl. 0.007 0.008 Over 9 to 12 incl. 0.008 0.009 All material will conform to ASTM A 108. 12
STRESSPROOF Steel Bars STRESSPROOF steel bars are produced from a medium carbon manganese resulphurized steel that meets the AISI designation 1144. STRESSPROOF is made by a patented special process which consists of drawing the bar through a specially designed die under heavy draft. The bars are then stress relieved in a precisely controlled furnace. This special process produces material that is uniform from end-to-end, center to surface, and bar-to-bar. STRESSPROOF steel bars offer wearability without case hardening, strength without heat treating, plus excellent machinability and tool life. Other benefits include resistance to fatigue and stress, balanced working, and minimum warpage and distortion. SPECIFICATIONS CHEMISTRY MECHANICAL PROPERTIES Carbon.........0.40/0.48% Tensile Strength............115,000 psi (min) Manganese......1.35/1.65% Yield Strength..............100,000 psi (min) Phosphorus.....1.040% max Machining Characteristics.......83% of C-1212 Sulfur..........0.24/0.33% Elongation.............................** Silicon..........0.15/0.30% Reduction of Area.......................**........................ Rockwell Hardness.................24-26 Rc........................ **Will meet ASTM A311 Class B.............................. **Value varies with size. MICROSTRUCTURE Pearlite and Ferrite SIZE RANGE Rounds 1/4" through 4-1/2" LENGTH 11-13 ft. or cut-to-length pieces FINISH as drawn smooth, accurate and dark in color APPLICATIONS All kinds of shafts, arbors, gears, pinions, bushings, mandrels, pins, lead screws, collets, spindles and many more applications. TOLERANCES Rounds 1/4" to 1-1/2" incl..........0.004" Over 1-1/2" to 2-1/2" incl....0.005" Over 2-1/2" to 4" incl.......0.006" Over 4" to 4-1/2" incl.......0.007" COLOR CODE Pink Tolerances, in decimals of an inch, provide for undersize variation only. Stressproof is a registered trademark of Niagara LaSalle Corporation. 13
Carbon Steel Cold Finished Hexagons 10/12' Lengths Size Wt/Ft Wt/12' 1214L Other 3/16.104 1.24 S... 1/4.184 2.21 S... 5/16.288 3.45 S... 3/8.414 4.97 S... 7/16.564 6.76 S... 1/2.736 8.83 S... 9/16.932 11.2 S... 5/8 1.15 13.8 S 1018 11/16 1.39 16.7 S... 3/4 1.66 19.9 S... 13/16 1.94 23.3 S... 7/8 2.25 27.1 S... 15/16 2.59 31.1 S... 1 2.94 35.3 S 1018 1-1/16 3.32 39.9 S... 1-1/8 3.73 44.7 S... 1-3/16 4.15 49.8 S... 1-1/4 4.60 55.2 S 1018 1-5/16 5.07 60.9 S... 1-3/8 5.57 66.8 S... 1-1/2 6.63 79.5 S... 1-5/8 7.78 93.3 S... 1-3/4 9.02 108 S... 1-7/8 10.4 124 S... 2 11.8 141 S... All material will conform to ASTM A 108. 14
Carbon Steel Cold Finished Hexagons 10/12' Lengths Size Wt/Ft Wt/12' 1214L Other 2-1/4 14.9 179 S... 2-3/8 16.6 199 S... 2-1/2 18.4 221 S... 2-3/4 22.3 267... 1117 3 26.5 318 S... 3-1/4 31.1 373... 1018 3-1/2 36.1 433... 1018 3-3/4 41.4 497... 1018 4 47.1 565... 1018 Tolerances Cold Drawn Hexagons (Minus tolerances in inches) Maximum Maximum Carbon Range Carbon Range of over.28% Specified Size in Inches of.28% or less to.55% incl Up to 3/4 incl..002.003 Over 3/4 to 1-1/2 incl..003.004 Over 1-1/2 to 2-1/2 incl..004.005 Over 2-1/2 to 3-1/8 incl..005.006 Over 3-1/8 to 4 incl..005.006 All material will conform to ASTM A 108. 15
Carbon Steel Cold Finished Squares 10/12' Lengths Size Wt/Ft Wt/12' 1018 Other 1/8 0.053 0.637 S... 3/16.120 1.44 S... 1/4.213 2.55 S 12L14 5/16.332 3.98 S 12L14 3/8.478 5.74 S 12L14 7/16.651 7.81 S 12L14 1/2.850 10.2 S 12L14 9/16 1.08 12.9 S... 5/8 1.33 15.9 S 1215 11/16 1.61 19.3 S... 3/4 1.91 23.0 S 12L14 13/16 2.25 26.9 S... 7/8 2.60 31.2 S 1215 15/16 2.99 35.9 S... 1 3.40 40.8 S 1215 1-1/8 4.30 51.6 S... 1-3/16 4.80 57.5 S... 1-1/4 5.31 63.8 S 12L14 1-5/16 5.86 70.3 S... 1-3/8 6.43 77.1 S... 1-1/2 7.65 91.8 S 12L14 1-5/8 8.98 108 S 12L14 1-3/4 10.4 125 S 12L14 1-7/8 12.0 143 S... 2 13.6 163 S 12L14 2-1/4 17.2 207 S... 2-3/8 19.2 230 S... 2-1/2 21.3 255 S 12L14 2-3/4 25.7 309 S... 3 30.6 367 S... All material will conform to ASTM A 108. 16
Carbon Steel Cold Finished Squares 10/12' Lengths Size Wt/Ft Wt/12' 1018 Other 3-1/4 35.9 431 S... 3-1/2 41.7 500 S... 3-3/4 47.8 574 S... 4 54.4 653 S... 4-1/2 68.9 826 S... 5 85.0 1020 S... 6 122 1469 S... Tolerances Cold Drawn Squares (Minus tolerances in inches) Maximum Maximum Carbon Range Carbon Range of over.28% Specified Size in Inches of.28% or less to.55% incl Up to 3/4 incl..002.004 Over 3/4 to 1-1/2 incl..003.005 Over 1-1/2 to 2-1/2 incl..004.006 Over 2-1/2 to 4 incl..006.008 Over 4 to 5 incl..010 Over 5 to 6 incl..014 All material will conform to ASTM A 108. 17
Turned Ground & Polished C-1141 Shafting 20/24' Lengths Size Wt/Ft Wt/Bar Size Wt/Ft Wt/Bar * 3/4 1.50 18 * 7/8 2.05 25 * 1 2.67 32 1-1/8 3.38 81 1-3/16 3.77 91 2-7/16 15.9 381 2-1/2 16.7 401 2-11/16 19.3 463 2-3/4 20.2 485 2-15/16 23.0 553 1-1/4 4.17 100 1-5/16 4.60 110 1-3/8 5.05 121 1-7/16 5.52 132 1-1/2 6.01 144 1-9/16 6.52 157 1-5/8 7.05 169 1-11/16 7.60 183 1-3/4 8.18 196 1-7/8 9.39 226 1-15/16 10.0 241 2 10.7 257 2-3/16 12.8 307 2-1/4 13.5 325 2-3/8 15.1 362 3 24.0 577 3-3/16 27.1 652 3-1/4 28.2 677 3-7/16 31.6 758 3-1/2 32.7 785 3-15/16 41.4 994 4 42.7 1026 4-1/4 48.2 1158 4-7/16 52.6 1262 4-1/2 54.1 1298 4-15/16 65.1 1562 5 66.8 1602 6 96.1 2307 * Size stocked in 12' lengths Tolerance in inches for TG&P Shafting 1-1/2" and under -.0005" / -.0015" Over 1-1/2" to under 2-1/2" -.0005" / -.0020" 2-1/2" to 3" -.0005" / -.0025" Over 3" to 4" -.0005" / -.0035" Over 4" to 6" -.0005" / -.0040" 18
Drawn, Ground & Polished Accuracy stock 10/12' Lengths Size Wt/Ft Wt/12' C-1215 C-1141 3/16.094 1.13 S... 1/4.167 2.00... S 5/16.261 3.13... S 3/8.376 4.51... S 7/16.511 6.13 S S 1/2.668 8.01 S S 9/16.845 10.1 S... 5/8 1.04 12.5 S S 11/16 1.26 15.1... S 3/4 1.50 18.0 S... 13/16 1.76 21.2... S 7/8 2.05 24.5 S... 15/16 2.35 28.2 S... 1 2.67 32.0 S... C-1045 METRIC Ground & Polished Shafting 12 Lengths Size Size EST. LBS EST. LBS MM INCHES PER FT. PER/12 12mm.4724.60 7.20 15mm.5906.93 11.16 16mm.6299 1.06 12.72 17mm.6693 1.20 14.40 18mm.7087 1.34 16.08 19mm.7480 1.49 17.88 20mm.7874 1.66 19.92 22mm.8661 2.00 24.00 24mm.9449 2.38 28.56 25mm.9843 2.59 31.08 30mm 1.1811 3.72 44.64 35mm 1.3780 5.07 60.84 40mm 1.5748 6.62 79.44 45mm 1.7717 8.38 100.56 50mm 1.9685 10.35 124.20 60mm 2.3622 14.90 178.80 80mm 3.1496 26.49 317.88 19
Low & Medium Carbon Rough Turned Steel Forgings 10/12' Lengths Size Wt/Ft C-1117 C-1141 8 178 S S 8-1/4 189 S S 8-1/2 200 S S 8-3/4 212 S S 9 224 S S 9-1/4 236 S S 9-1/2 249 S S 9-3/4 262 S... 10 277 S S 10-1/4 289 S S 10-1/2 303 S S 11 333 S S 11-1/2 364 S... 12 397 S S 12-1/2 430 S... 13 464 S S 14 537 S S 15 616 S... 16 700 S S 18 883 S S 20 1088 S S 21 1199 S... 22 1314 S... 23 1436 S... 24 1562 S... 25 1694 S... C-1117 Typical Chemical Analysis C Mn P S Si Ni Cr Mo.14/.20 1.00/1.30.040 max.08/.13.35 max.25 max.25 max.10 max C-1141 Typical Chemical Analysis C Mn P S Si Ni Cr Mo.37/.45 1.35/1.65.040 max.08/.13.35 max.25 max.25 max.10 max Diameter Tolerance plus.125/.188" (Will finish to nominal size) 500 RMS Finish Meets ASTM A-576 20
Carbon Steel Hot Rolled Rounds 20' Lengths Size Wt/Ft C-1117 C-1141 C-1018 2 10.7 S S... 2-1/4 13.5 S S... 2-1/2 16.7... S... 2-3/4 20.2... S... 3 24.0 S S... 3-1/4 28.2 S S... 3-1/2 32.7 S S... 3-3/4 37.6 S S... 4 42.7 S S... 4-1/4 48.2 S S... 4-1/2 54.1 S S... 4-3/4 60.3 S S... 5 66.8 S S... 5-1/4 73.6 S S... 5-1/2 80.8 S S... 5-3/4 88.4 S S... 6 96.1 S S... 6-1/4 104 S S S 6-1/2 113 S S... 6-3/4 122 S S... 7 131 S S... 7-1/4 140 S S... 7-1/2 150 S S... 7-3/4 160 S...... 8 171 S...... 9 216 RT S S 9-1/2 241 RT RT S 10 267 RT RT S RT=Stocked in Rough Turned 21
Carbon Steel Hot Rolled Angles 20' Lengths Size Wt/Ft Wt/20' 3/4 x 3/4 x 1/8.6 12 1 x 1 x 1/8.8 16 1 x 1 x 3/16 1.2 23 1 x 1 x 1/4 1.5 30 1-1/4 x 1-1/4 x 1/8 1.0 20 1-1/4 x 1-1/4 x 1/4 1.9 38 1-1/2 x 1-1/2 x 1/8 1.2 25 1-1/2 x 1-1/2 x 3/16 1.8 36 1-1/2 x 1-1/2 x 1/4 2.3 47 2 x 2 x 1/8 1.7 33 2 x 2 x 3/16 2.4 49 2 x 2 x 1/4 3.2 64 2 x 2 x 3/8 4.7 94 2-1/2 x 2-1/2 x 1/4 4.1 82 3 x 3 x 1/4 4.9 98 3 x 3 x 3/8 7.2 144 3 x 3 x 1/2 9.4 188 4 x 4 x 1/4 6.6 132 4 x 4 x 3/8 9.8 196 4 x 4 x 1/2 12.8 256 4 x 4 x 3/4 18.5 370 5 x 5 x 1/2 16.2 324 6 x 6 x 3/8 14.9 298 6 x 6 x 1/2 19.6 392 6 x 6 x 3/4 28.7 574 8 x 8 x 1/2 26.4 528 8 x 8 x 1 51.0 1020 Will conform to ASTM A 36. Other sizes available upon request. 22
Carbon Steel Hot Rolled Channels 20' Lengths Size Wt/Ft Wt/20' 2 x 1 x 3/16 2.3 47 3 x 4.1 4.1 82 4 x 5.4 5.4 108 5 x 6.7 6.7 134 6 x 8.2 8.2 164 8 x 11.5 11.5 230 Will conform to ASTM A 36. Other sizes available upon request. 23
Carbon Steel Threaded Rod 6' Lengths Size Wt/6' Size Wt/6' 8-32.180 10-32.420 1/4-20.750 1/4-28.780 5/16-18 1.17 3/8-16 1.73 3/8-24 1.92 1/2-13 3.20 1/2-20 3.40 5/8-11 5.07 3/4-10 7.38 7/8-9 10.2 1-8 13.5 Alloy Steel 4140 Annealed Cold Drawn Rounds 12' Lengths Size Wt/Ft Size Wt/Ft 1/4.167 3/8.376 1/2.668 5/8 1.04 3/4 1.50 7/8 2.05 1-0/0 2.67 1-1/16 3.02 1-1/4 4.17 1-5/16 4.60 1-1/2 6.01 1-5/8 7.05 1-3/4 8.18 2-0/0 10.7 2-1/4 13.5 2-1/2 16.7 2-3/4 20.2 3-0/0 24.0 3-1/4 28.2 3-1/2 32.7 4-0/0 42.7 24
Alloy Steel 4140 Quenched and Tempered Ground & Polished Shafting 20' Lengths Size Wt/Ft Wt/24' Size Wt/Ft Wt/24' * 1/2.668 * 8.02 9/16.845 20.3 5/8 1.04 25.0 3/4 1.50 36.0 7/8 2.045 49.1 1 2.67 64.1 1-1/8 3.38 81.1 1-3/16 3.77 90.4 1-1/4 4.17 100 1-3/8 5.05 121 1-7/16 5.52 132 1-1/2 6.01 144 1-5/8 7.05 169 1-11/16 7.60 182 1-3/4 8.18 196 1-7/8 9.39 225 1-15/16 10.0 240 50mm (1.969) 10.4 250 2 10.7 256 2-1/8 12.1 289 2-3/16 12.8 307 2-1/4 13.5 324 60mm (2.3622) 14.9 358 *Stocked in 12' lengths. 2-3/8 15.1 361 2-7/16 15.9 382 2-1/2 16.7 401 2-5/8 18.4 442 2-11/16 19.3 463 2-3/4 20.2 485 2-7/8 22.1 530 2-15/16 23.0 553 3 24.0 577 80mm (3.1496) 26.5 636 3-3/16 27.1 651 3-1/4 28.2 677 3-7/16 31.6 757 3-1/2 32.7 785 90mm (3.5433) 33.5 805 100mm (3.9370) 41.38 993 3-15/16 41.4 994 4 42.7 1025 4-1/4 48.2 1158 4-7/16 52.6 1262 4-1/2 54.1 1298 4-15/16 65.1 1562 Typical Chemical Analysis C Mn P S Si Cr Mo.38/.43.75/1.00.035 max.040 max.15/.35.80/1.10.15/.25 Tolerances 1-1/2" and under -.0005" / -.0015" Over 1-1/2" to under 2-1/2" -.0005" / -.0020" 2-1/2" to 3" -.0005" / -.0025" Over 3" to 4" -.0005" / -.0035" Over 4" to 6" -.0005" / -.0040" Hardness 28/32 Rc ASTM A193 Gr B7 * Sizes are DG&P 12' Long ASTM A434 Gr BC 25
Alloy Steel 4140 Annealed Cold Drawn Squares 12' Lengths Size Wt/Ft Size Wt/Ft 1/4.213 3/8.478 1/2.850 3/4 1.91 7/8 2.60 1-0/0 3.40 1-1/4 5.31 1-3/8 6.43 1-1/2 7.65 2-0/0 13.6 2-1/2 21.3 3-0/0 30.6 Alloy Steel 4140 Annealed Cold Drawn Hexagons 12' Lengths Size Wt/Ft Size Wt/Ft 1/4.184 3/8.414 1/2.740 5/8 1.15 3/4 1.66 7/8 2.25 1-0/0 2.94 1-1/8 3.73 1-1/4 4.60 1-1/2 6.63 2-0/0 11.8 3-0/0 26.5 26
Alloy Steel 4140/50 RS Hot Rolled Rounds 20/24' Lengths Size Wt/Ft Annealed Heat Treated * 1/2.667 S S * 5/8 1.04 S S * 3/4 1.50 S S * 7/8 2.05 S S * 1 2.67 S S * 1-1/8 3.38 S S * 1-1/4 4.17 S S * 1-3/8 5.05 S S * 1-1/2 6.01 S S * 1-5/8 7.05 S S * 1-3/4 8.18 S S * 1-7/8 9.39 S S * 2 10.7 S S * 2-1/8 12.1 S S * 2-1/4 13.5 S S * 2-3/8 15.1 S S * 2-1/2 16.7 S S * 2-5/8 18.4 S S * 2-3/4 20.2 S S * 2-7/8 22.1 S S 3 24.0 S S 3-1/4 28.2 S S 3-1/2 32.7 S S 3-3/4 37.6 S S 4 42.7 S S 4-1/4 48.2 S S 4-1/2 54.1 S S 4-3/4 60.3 S S 5 66.8 S S 5-1/4 73.6 S S *Stocked as 4140. 27
Alloy Steel 4140/50 RS Hot Rolled Rounds 20/24' Lengths Size Wt/Ft Annealed Heat Treated 5-1/2 80.8 S S 5-3/4 88.4 S S 6 96.1 S S 6-1/4 104 S S 6-1/2 113 S S 6-3/4 122 S S 7 131 S S 7-1/4 140 S S 7-1/2 150 S S 7-3/4 160 S S 8 171 S S 8-1/4 182 S S 8-1/2 193 S S 8-3/4 205 S S 9 222 S S 9-1/2 248 S S 10 274 S S Alloy Steel E52100 H.R. Annealed Rounds 20' Lengths Size Wt/Ft 1 2.67 1-1/2 6.01 2 10.7 2-1/2 16.7 3 24.0 3-1/2 32.7 4 42.7 4-1/2 54.1 5 66.8 6 96.1 28
Alloy Steel 8620 Hot Rolled Rounds 20' Lengths Size Wt/Ft Wt/20 3/4 1.50 30 1 2.67 53 1-1/4 4.17 83 1-1/2 6.01 120 1-3/4 8.18 164 2 10.7 214 2-1/4 13.5 270 2-1/2 16.7 334 2-3/4 20.2 404 3 24.0 481 3-1/4 28.2 564 3-1/2 32.7 654 3-3/4 37.6 752 4 42.7 855 4-1/4 48.2 965 4-1/2 54.1 1081 5 66.8 1335 5-1/2 80.8 1616 6 96.1 1923 6-1/2 113 2256 7 131 2616 7-1/2 150 3000 8 171 3418 8-1/2 193 3860 9 216 4320 10 267 5340 11 323 6461 *12 393 *13 460 *14 533 *16 700 Typical Chemical Analysis C Mn P S Si Ni Cr Mo.18/.23.70/.90.035 max.040 max.15/.35.40/.70.40/.60.15/.25 Meets ASTM A-29, A-322, A-304 *Size is rough turned 29
Alloy Steel 4150 Modified Resulphurized Rough Turned Forgings 12' Lengths Size Wt/Ft Annealed Heat Treated 9 223 S *HR 9-1/2 248 S S 10 274 S S 10-1/2 302 S S 11 331 S S 11-1/2 361 S S 12 393 S S 12-1/2 426 S S 13 460 S S 14 533 S S 15 611 S S 16 698 S S 17 789 S S 18 884 S S 19 984 S S 20 1090 S S 21 1199 S... 22 1314 S... 23 1436 S... 24 1562 S... 25 1694 S... Typical Chemical Analysis C Mn P S Si Ni Cr Mo.48/.53.95/1.30.035 max.06/.10.20/.30.25 max.60/.90.15/.25 Diameter Tolerance Plus.125/.188" Brinell Hardness on Heat Treated 277/311 500 RMS Finish Meets ASTM A-322 *HR = Size is Hot Rolled. 30
Stainless Steel Rounds 10/12' Lengths Size Wt/Ft Wt/12 T-303 T-304 T-316 T-416 1/8.042.500 S...... S 5/32.065.782............ 3/16.094 1.13 S S S... 1/4.167 2.00 S S S S 5/16.261 3.13 S...... S 3/8.376 4.51 S S S S 7/16.511 6.13 S......... 1/2.668 8.01 S S S S 9/16.845 10.1 S S S... 5/8 1.04 12.5 S S S S 11/16 1.26 15.1 S......... 3/4 1.50 18.0 S S S S 13/16 1.76 21.2 S......... 7/8 2.05 24.5 S S S S 15/16 2.35 28.2 S......... 1 2.67 32.0 S S S S 1-1/16 3.02 36.2 S......... 1-1/8 3.38 40.6 S...... S 1-3/16 3.77 45.2 S......... 1-1/4 4.17 50.1 S S S S 1-5/16 4.60 55.2 S......... 1-3/8 5.05 60.6 S... S S 1-7/16 5.52 66.2 S...... S 1-1/2 6.01 72.1 S S S S 1-5/8 7.05 84.6 S...... S 1-3/4 8.18 98.1 S S S S 1-7/8 9.39 113 S......... 2 10.7 128 S S S S 2-1/8 12.1 145 S......... 2-1/4 13.5 162 S S S... Other sizes & grades available on request. 31
Stainless Steel Rounds 10/12' Lengths Size Wt/Ft Wt/12' T-303 T-304 T-316 T-416 2-3/8 15.1 181 S......... 2-1/2 16.7 200 S S S... 2-5/8 18.4 221 S......... 2-3/4 20.2 242 S S S... 2-7/8 22.1 265 S......... 3 24.0 288 S S S S 3-1/4 28.2 339 S......... 3-1/2 32.7 393 S S S S 3-3/4 37.6 451 S......... 4 42.7 513 S S S... 4-1/2 54.1 649 S... S... 5 66.8 801 S... S S 5-1/2 80.8...... S...... 6 96.1 1154 S S...... 6-1/2 115 1380... S...... 7 131 1570 S S...... 8 171 2052 S......... Other sizes & grades available on request. Type 304 C.D.A. Stainless Steel Squares 10/12' Lengths Size Wt/Ft Size Wt/Ft 3/16.1200 7/8 2.606 1/4.2127 1 3.403 3/8.4786 1-1/4 5.318 1/2.8508 1-1/2 7.657 5/8 1.329 2 13.61 3/4 1.914 Other sizes & grades available on request. 32
Type 304 Stainless Steel H.R.A.P. Flats 12' Lengths Size Wt/Ft Size Wt/Ft 1/8 x 1/2.2127 3/4.3191 1-0/0.4254 1-1/2.6381 2-0/0.8508 2-1/2 1.064 3-0/0 1.276 3/16 x 1/2.3191 3/4.4786 1-0/0.6381 1-1/2.9572 2-0/0 1.276 2-1/2 1.595 1/4 x 1/2.4254 5/8.5318 3/4.6381 1-0/0.8508 1-1/4 1.064 1-1/2 1.276 2-0/0 1.702 2-1/2 2.127 3-0/0 2.552 4-0/0 3.403 3/8 x 1/2.6381 3/4.9572 1-0/0 1.276 1-1/4 1.595 1-1/2 1.914 2-0/0 2.552 2-1/2 3.191 3-0/0 3.829 4-0/0 5.105 1/2 x 3/4 1.276 1-0/0 1.702 1-1/4 2.127 1/2 x 1-1/2 2.552 2-0/0 3.403 2-1/2 4.254 3-0/0 5.105 4-0/0 6.806 6-0/0 10.21 5/8 x 3/4 1.594 1-0/0 2.127 1-1/2 3.191 2-0/0 4.254 2-1/2 5.318 3-0/0 6.381 4-0/0 8.508 3/4 x 1-0/0 2.552 1-1/4 3.191 1-1/2 3.829 2-0/0 5.105 2-1/2 6.381 3-0/0 7.657 4-0/0 10.21 6-0/0 15.30 1 x 1-1/4 4.254 1-1/2 5.105 2-0/0 6.806 2-1/2 8.508 3-0/0 10.21 4-0/0 13.61 6-0/0 20.40 1-1/2 x 6-0/0 30.60 2 x 6-0/0 40.80 Other sizes & grades available on request. 33
CDA 360 H.H. Brass Rounds 10/12' Length Size Wt/Ft Size Wt/Ft -1/16.011-3/32.025-1/8.045-5/32.071-3/16.102-7/32.138-1/4.181-17/64.204-9/32.229-5/16.283-21/64.312-3/8.407-25/64.441-7/16.554-1/2.723-9/16.920-5/8 1.13-11/16 1.37-3/4 1.63-25/32 1.77-13/16 1.91-27/32 2.06-7/8 2.22-15/16 2.54 1-0/0 2.89 1-1/16 3.27 1-1/8 3.66 1-3/16 4.08 1-1/4 4.52 1-5/16 4.98 1-3/8 5.47 1-1/2 6.51 1-9/16 7.06 1-5/8 7.64 1-3/4 8.86 1-13/16 9.51 1-7/8 10.2 2 11.6 2-1/8 13.1 2-1/4 14.6 2-3/8 16.2 2-1/2 18.1 2-5/8 19.9 2-3/4 21.9 3 26.0 3-1/4 30.6 3-1/2 35.4 3-3/4 40.7 4 46.3 4-1/4 52.3 4-1/2 58.6 5 72.3 5-1/2 87.5 5-3/4 96 6 104 7 142 8 185 Will conform to ASTM B 16 and SAE 72. 34
CDA 360 H.H. Brass Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 1/8 x 3/8.173 1/2.230 5/8.288 3/4.345 7/8.403 1-0/0.461 1-1/4.576 1-1/2.691 1-3/4.806 2-0/0.921 2-1/2 1.15 3-0/0 1.38 4-0/0 1.84 3/16 x 1/2.345 5/8.430 3/4.518 7/8.604 1-0/0.691 1-1/4.863 1-1/2 1.04 2-0/0 1.38 3-0/0 2.07 4-0/0 2.76 1/4 x 3/8.345 1/2.461 5/8.576 3/4.691 7/8.806 1-0/0.921 1-1/4 1.15 1-1/2 1.38 1-3/4 1.61 2-0/0 1.84 2-1/2 2.30 3-0/0 2.76 4-0/0 3.68 6-0/0 5.53 5/16 x 1/2.576 5/8.720 3/4.863 1-0/0 1.15 1-1/2 1.73 1-3/4 2.02 2-0/0 2.30 3/8 x 1/2.691 3/4 1.04 1-0/0 1.38 1-1/4 1.73 1-1/2 2.07 2-0/0 2.76 2-1/2 3.45 3-0/0 4.15 3-1/2 4.84 4-0/0 5.53 6 8.29 1/2 x 5/8 1.15 3/4 1.38 7/8 1.61 1-0/0 1.84 1-1/4 2.30 1-1/2 2.76 1-3/4 3.22 2-0/0 3.68 2-1/2 4.61 3 5.53 4 7.37 6-1/2 11.2 5/8 x 3/4 1.73 7/8 2.02 1-0/0 2.30 1-1/4 2.88 1-1/2 3.45 2-0/0 4.61 35
CDA 360 H.H. Brass Flats 10/12' Lengths Size Wt/Ft Size Wt/Ft 5/8 x 3-0/0 6.91 4-0/0 9.21 3/4 x 1-0/0 2.76 1-1/4 3.45 1-1/2 4.15 1-3/4 4.84 2-0/0 5.53 2-1/2 6.91 3-0/0 8.29 4-1/20 011.1 6 1 x 1-1/4 4.61 1-1/2 5.53 2-0/0 7.37 2-1/2 9.21 3-0/0 11.1 4-0/0 14.7 6-1/2 22.2 1-1/2 x 2-0/0 11.1 2-1/2 13.8 3-0/0 16.6 2 x 3-0/0 22.2 4 29.5 CDA 360 H.H. Brass Hexagons 10/12' Length Size Wt/Ft Size Wt/Ft 3/16.112 1/4.199 5/16.312 3/8.449 7/16.611 1/2.798 9/16 1.01 5/8 1.25 11/16 1.51 3/4 1.80 7/8 2.44 15/16 2.80 1-0/0 3.19 1-1/16 3.60 1-1/8 4.04 1-1/4 4.99 1-3/8 6.03 1-1/2 7.18 1-5/8 8.43 1-3/4 9.77 2-0/0 12.8 2-1/2 19.9 Will conform to ASTM B 16 and SAE 72. 36
CDA 360 H.H. Brass Squares 10/12' Length Size Wt/Ft Size Wt/Ft 1/8.058 3/16.130 1/4.230 5/16.360 3/8.518 7/16.705 1/2.921 5/8 1.44 3/4 2.07 7/8 2.82 1-0/0 3.68 1-1/8 4.66 1-1/4 5.76 1-1/2 8.29 1-3/4 11.3 2-0/0 14.7 2-1/2 23.0 2-3/4 27.9 3-0/0 33.2 Will conform to ASTM B 16 and SAE 72. Other sizes available on request. 37
38
Continuous CAST IRON Bar Stock for high quality parts GRAY IRON The close grain, dense iron permits precision machining at optimum speeds. Uniform hardness helps produce a consistent end product. Mechanical Properties Type G1A* G1 G2 Tensile strength psi (min)** 25,000 30,000 40,000 Compressive strength psi (min)** n/a 120,000 150,000 Transverse strength average n/a 3,600 4,000 (lbs load on 1.2 bar 18 span) Deflection (inches) n/a 0.20-0.34 0.25-0.34 Type A size 4 or smaller Graphite Type D Type D size 6 or smaller Modulus of elasticity (million psi)** n/a 17.0 18.0 min Heat-treat response (quench hardness) n/a Rc 40 min Rc 50 min Hardness (BHN) 3/4" - 1-1/2" 159-229 179-235 229-285 1-1/2" - 3" 156-201 163-229 207-277 3" - 6" 143-201 151-229 197-269 6" - 20" 143-201 143-201 183-269 Microstructure Highly Partially Highly ferritic ferritic pearlitic * Designed for dimensional stability when subjected to repeated heating and cooling cycles. ** Determined as prescribed by ASTM standards. 39
Continuous CAST IRON Bar Stock for high quality parts DUCTILE IRON Ductile iron combines high strength, ductility, toughness and hardenability with the processing advantages of cast iron. Mechanical Properties Type 65-45-12 80-55-06 100-70-02 Tensile strength psi (min)* 65,000 80,000 100,000 Yield strength psi (min)* 45,000 55,000 70,000 Elongation % psi (min)* 12 6 2 Hardness (BHN) 131-207 207-269 241-302 Modulus of elasticity (million psi)* 23-26 23-26 23-26 Heat-treat response (quench hardness) n/a Rc 55 min Rc 55 min Microstructure Ferritic Partially Pearlitic (min 75% pearlitic (min 75% ferrite) (approx 50% pearlite) pearlite) * Determined as prescribed by ASTM standards. 40
Continuous CAST IRON Bar Stock for high quality parts Ni-RESIST This austenitic material resists corrosion, erosion, oxidation and operational wear. It has low temperature stability and is heat resistant. Mechanical Properties Type 1 2 Tensile strength psi (min)* 25,000 25,000 Compressive strength psi (min)* 100,000 100,000 Hardness (BHN) 131-183 118-174 Modulus of elasticity (psi x 10 6 at 25% of tensile) 12-14 15-16.2 Thermal exp. (70º-400ºF millionths per ºF) 10.7 10.4 Magnetic response non-magnetic non-magnetic * Determined as prescribed by ASTM standards. 41
Continuous CAST IRON Bar Stock for high quality parts HTN (Heat Treatable Nodular Iron) HTN is a ductile iron. This high hardenability material is designed for austempering or conventional heat treatment to produce properties possessing high strength and excellent wear resistance. Properties of HTN Ductile Iron In the as-cast condition, depending on section size and cooling rate, HTN alloyed ductile iron parts produced for austempering can meet 80-55-06* grade, or even 100-70-02 grade. In certain cases, however, the as-cast parts could be ferritic (as they certainly would be after a ferritizing anneal), and will have a hardness in the range of 160-180 HB, ensuring the lowest possible machining costs. The table below contains the expected minimum and/or typical properties of HTN and an austempering schedule for achieving these properties. *T.S.=80 ksi; Y.S.=55 ksi; Elong=6% Minimum Mechanical Properties After Austempering Treatment Grade Suggested Tensile 0.2% Offset Elongation Typical Unnotched Treatment Strength Yield % Hardness Charpy Bar Temperature Time MPa (ksi) Strength HB Energy at C (F) h MPa (ksi) Room Temperature J (ft-lb) 1 400 (750)** 0.5-2 860 (125) 585 (85) 10 269-331 110 (80) 2 355 (675) 1.25-8 1035 (150) 690 (100) 7 302-363 90 (65) 3 315 (600) 1.25-8 1200 (175) 830 (120) 4 341-415 60 (45) 4 260 (500) 1.0-8 1380 (200) 965 (140) 2 375-461 40 (30) ** Austenitized at 845 C (1550 F); all other grades austenitized at 900 C (1650 F); elongation and toughness tend to be improved by lowering the austenitizing temperature. 42
How Dura-Bar and Dura-Tube Save You Money Thousands of diverse components can be made more efficiently and profitably with Dura- Bar or Dura-Tube. The fine grain structure and uniform hardness of Dura-Bar products permit precision machining at optimum speeds for efficient, cost effective operation. Dura-Bar products help extend tool life and reduce tool maintenance because they are free of inclusions and hard spots. Dura-Bar products reduce scrap loss to less than 0.5% to virtually eliminate remake and downtime. Dura-Bar products guarantee internal soundness. The trepanned bore in Dura-Tube eliminates the time-consuming machining operation of drilling. The wide range of sizes and immediate availability of Dura-Bar products eliminate the need for expensive patterns and costly inventories. Dura-Bar and Dura-Tube Sizes and Shapes Dura-Bar and Dura-Tube are produced in a wide range of sizes, shapes and lengths. Dura-Bar Dura-Tube Nominal Increment Inside Outside diameter* available diameter diameter 1/2" - 4" 1/8" 4-1/4" - 11" 1/4" 1-1/2" - 7" 2-1/2" - 16" 11-1/2" - 15" 1/2" 16" - 20" 1" Other sizes available on request. * As-cast Dura-Bar will finish at the size specified with minimum stock removal. Centerless turned bars are available up to 6" in diameter. Rectangles and Squares Rectangular sizes up to 14" thick and 21" wide are available. Standard square sizes range from 1-1/4" to 12-1/4". Also available, custom saw cut plate to your specifications. Special Profiles Half rounds, quarter rounds, and other shapes are quoted on request. 43
Dura-Bar and Dura-Tube Typical Applications Bearings Rotors Bushings Seal rings Cams Shafts Conveyor guide rollers Sprockets Couplings Valve bodies Cylinders Valve guides Dies Gibs Gears Ways Pistons Collets Pulleys Sleeves Rams Rolls Immediate Shipment Dura-Bar is more than just a product it s a service. We will cut bars and tubes to any specifications or lengths, and ship them immediately. We maintain a large inventory of bars and tubes in a wide range of sizes and shapes, eliminating the need for you to hold a costly inventory of parts or castings. Call us for more information on how Dura-Bar products will increase your machining productivity. 44
G-2 Dura-Bar Class 40 Gray Iron Rounds 6' Lengths Size Wt/Ft Wt/Bar Size Wt/Ft Wt/Bar 1-2.625 4 5/8.973 6 3/4 1.40 9 7/8 1.90 12 1 2.48 15 1-1/8 3.13 19 1-1/4 3.86 24 1-3/8 4.67 29 1-1/2 5.55 34 1-5/8 6.51 40 1-3/4 7.55 47 1-7/8 8.66 53 2 9.85 61 2-1/8 11.1 69 2-1/4 12.5 77 2-3/8 13.9 86 2-1/2 15.4 95 2-5/8 17.0 105 2-3/4 18.6 115 2-7/8 20.3 125 5 61.5 384 5-1/4 67.7 423 5-1/2 74.3 465 5-3/4 81.2 508 6 88.4 553 6-1/4 101 631 6-1/2 109 681 6-3/4 117 733 7 126 787 7-1/4 136 848 7-1/2 145 906 7-3/4 155 966 8 165 1027 8-1/4 176 1098 8-1/2 186 1164 8-3/4 197 1231 9 208 1301 9-1/2 233 1457 10 258 1621 10-1/4 278 1738 * 3 22.1 136 3-1/8 24.0 148 3-1/4 26.0 160 3-3/8 28.0 173 3-1/2 30.1 186 3-5/8 32.3 199 3-3/4 34.6 213 4 39.3 246 4-1/4 44.4 278 4-1/2 49.8 311 4-3/4 55.5 347 ** ** 10-1/2 291 1832 11 319 2004 12 388 2441 12-1/2 419 2621 13 452 2844 14 521 3278 15 595 3743 16 674 4239 17 773 4864 18 863 5427 19 957 4825 20 1057 5061 22 1187 2968 23 1297 3242 * Sizes under 3" are CENTERLESS TURNED to size. * Sizes 3" and up are AS-CAST OVERSIZE and will finish to nominal size. ** Stocked in 30" lengths. 45
Dura-Tube Cast Iron 6 Lengths OD ID Wt/Ft G-2 80-55-06 3-1/4 1-1/2 24.1 S... 3-1/2 28.9 S... 4-1/2 49.9 S... 3-1/2 2 24.7 S... 4 34.9 S... 5 58.3 S... 6 87.0 S... 4-1/4 2-1/2 35.1 S S 4-1/2 41.1 S... 5 52.3 S... 5-1/2 67.2 S... 6 80.4 S S 6-1/4 89.0 S... 6-1/2 98.4 S... 7-1/2 135.0 S... 4 3 23.1 S... 4-1/2 34.0... S 4-3/4 41.0... S 5 47.0 S S 5-1/4 55.7... S 6 75.7 S S 7 110.0 S... 8 149.0 S... 4-3/4 3-1/4 38.0... S 6-1/2 86.9... S 5 3-1/2 39.0 S... 5-1/2 53.4 S... 6 66.9... S 6-1/2 84.7 S S 7-1/2 122.0 S... 8-1/2 163.0 S... Other sizes and grades available upon request. ID and OD will finish to nominal size. 46
Dura-Tube Cast Iron 6 Lengths OD ID Wt/Ft G-2 80-55-06 5-3/4 3-3/4 55.9 S S 6 4 59.4 S... 6-1/4 67.0 S... 7 93.2 S S 8 132.0 S... 9 177.0 S... 7-1/4 4-1/4 96.3... S 6-1/2 4-1/2 65.9 S... 7-1/2 103.0 S... 8 120.0 S... 8-1/2 145.0 S... 7 5 71.9 S S 8 111.0 S... 9 156.0 S... 7-1/2 5-1/2 78.7 S... 8-1/2 121.0 S... 9 140.0 S... 8 6 84.8 S... 9 129.0 S... 9 7 96.0 S... Other sizes and grades available upon request. ID and OD will finish to nominal size. 47
G-2 Dura-Bar Class 40 Gray Iron Flats 6 Lengths Size Wt/Ft Size Wt/Ft 3/4 x 1-1/2 3.51 3-0/0 7.02 1 x 1-1/2 4.68 2-1/2 x 2-3/4 21.5 3-1/4 25.4 4-1/4 33.2 6-1/4 48.8 8-1/4 64.4 1-1/4 x 2-1/4 8.78 3-0/0 11.7 3-1/4 12.7 4-1/4 16.6 5-1/4 20.5 6-1/4 24.4 10-1/4 40.0 1-1/2 x 2-1/4 10.5 3-0/0 14.0 4-1/4 19.9 5-1/4 24.6 6-1/4 29.3 10-1/4 48.0 1-3/4 x 3-0/0 16.4 4-1/4 23.2 6-1/4 34.1 2-3/4 x 3-1/2 30.0 4-1/4 36.5 3-1/4 x 4-1/4 43.1 6-1/4 63.4 7-1/4 73.5 4-1/4 x 4-1/2 59.7 5-1/4 69.6 6-1/4 82.9 4-3/4 x 5-1/4 80.0 5-1/4 x 6-1/4 102.0 2 x 2-1/2 15.6 4-1/2 28.1 6 x 7-0/0 131.0 2-1/4 x 3-1/4 22.8 4-1/4 29.8 5-1/4 36.9 6-1/4 43.9 Sizes are As-Cast to nominal size. 48
G-2 Dura-Bar Class 40 Gray Iron Squares 6' Lengths Size Wt/Ft Size Wt/Ft 1-1/2 7.02 1-3/4 9.56 2-1/4 15.8 2-1/2 19.5 3-0/0 28.1 3-1/4 33.0 4-1/4 56.4 5-1/4 86.0 6-1/4 122.0 7-1/4 164.0 8-1/4 212.0 9-1/4 267.0 10-1/4 328.0 12-1/4 468.0 Sizes are As-Cast to nominal size. 49
We Specialize In Custom Saw Cut Plate! Available in the following grades: Class 40 Gray Iron 65-45-12 Ductile Iron 80-55-06 Ductile Iron Saw cutting allows you to order the raw material for your parts in a semi-finished form, dramatically reducing machining time in your plant. Only 1/16" Stock Allowance per Side Required for Finish Machining Purchase Less Weight No Minimum Quantity Material is Stress Relieved for Dimensional Stability Continuous Cast for Consistent Quality Available to your specifications up to 14" x 21" x 90" long 50
* Dura-Bar Ductile Iron Rounds 6' Lengths Size Wt/Ft Wt/Bar 80-55-06 65-45-12 1-1/2 5.55 34 S... 1-3/4 7.55 47 S... 1-7/8 8.66 53 S... 2-0/0 9.85 61 S S 2-1/4 12.5 77 S... 2-3/8 13.9 86 S... 2-1/2 15.4 95 S... 2-3/4 18.6 115 S... 3-0/0 22.1 136 S S 3-1/4 26.0 160 S... 3-1/2 30.1 186 S... 3-3/4 34.6 213 S... 4-0/0 39.3 246 S S 4-1/4 44.4 278 S... 4-1/2 49.8 311 S S 4-3/4 55.5 347 S... 5-0/0 61.5 384 S S 5-1/2 74.3 465 S S 5-3/4 81.2 508 S... 6-0/0 88.4 553 S S 6-1/4 102 635 S... 6-1/2 110 685 S S 7-0/0 127 792 S S 7-1/2 146 911 S S 8-0/0 165 1033 S S * Sizes 1/2" to under 3" are CENTERLESS TURNED to size. * Sizes 3" and up are AS-CAST OVERSIZE and will finish to nominal size. 51
Dura-Bar Ductile Iron Rounds 6' Lengths Size Wt/Ft Wt/Bar 80-55-06 65-45-12 8-1/2 187 1170 S S 9 209 1308 S S 9-1/2 235 1466 S... 10 259 1630 S S 10-1/2 293 1843 S... 11 320 2015 S S 12 391 2457 S S 13 455 2861 S... 14 524 3297 S S 15 598 3763 S... 16 677 4260 S S 17 778 4893 S... 18 868 5458 S... 20 1062 6682 S... ** 25 1696 4240... S * Sizes 1/2" to under 3" are CENTERLESS TURNED to size. * Sizes 3" and up are AS-CAST OVERSIZE and will finish to nominal size. ** Stocked in 30" lengths. 52
CDA 932 Bearing Bronze Hollow Bar 105" Lengths ID OD Wt/Ft ID OD Wt/Ft 1/2 1-0/0 2.6 1-1/4 4.4 1-1/2 6.7 2-0/0 12.2 1 2-3/4 21.4 3-0/0 25.8 3-1/2 36.1 4-0/0 48.7 5/8 1-0/0 2.3 1-1/8 3.1 1-1/4 4.1 1-1/2 6.2 1-5/8 7.6 1-3/4 8.9 2-0/0 11.8 3/4 1-1/4 3.6 1-3/8 4.7 1-1/2 5.8 1-3/4 8.4 2-0/0 11.4 2-1/2 18.5 7/8 1-1/8 2.1 1-3/8 4.1 1-1/2 5.2 1-5/8 6.5 1-3/4 7.8 2-0/0 10.8 1 1-1/4 2.3 1-1/2 4.6 1-3/4 7.1 2-0/0 10.1 2-1/4 13.4 2-1/2 17.2 1-1/8 1-3/8 2.6 1-5/8 4.9 2-0/0 9.2 1-1/4 1-1/2 2.9 1-3/4 5.4 2-0/0 8.4 2-1/4 11.8 2-1/2 15.5 2-3/4 19.7 3-0/0 24.1 3-1/4 29.0 3-1/2 34.4 4-0/0 47.3 1-3/8 2-0/0 7.4 2-1/8 9.0 2-1/4 10.8 2-1/2 14.5 3-0/0 23.2 1-1/2 1-3/4 3.4 2-0/0 6.4 2-1/4 9.7 2-1/2 13.4 2-3/4 17.6 3-0/0 22.1 3-1/4 27.0 3-1/2 32.3 Material will conform to SAE 660. Other sizes available upon request. 53
CDA 932 Bearing Bronze Hollow Bar 105" Lengths ID OD Wt/Ft ID OD Wt/Ft 1-1/2 3-3/4 38.0 4-0/0 45.4 4-1/2 58.8 1-5/8 2-1/8 6.8 2-3/4 16.4 3-0/0 20.9 1-3/4 2-1/2 10.5 2-3/4 15.1 3-0/0 19.7 3-1/4 24.6 3-1/2 29.9 3-3/4 35.5 4-0/0 43.0 1-7/8 2-3/8 7.7 2-5/8 11.6 3-0/0 18.2 2 2-1/2 8.2 2-5/8 10.2 2-3/4 12.2 3-0/0 16.8 3-1/4 21.7 3-1/2 27.0 4-0/0 40.2 4-1/2 53.6 5-0/0 70.0 6-0/0 105.0 2-1/4 2-3/4 9.1 3-0/0 13.6 3-1/4 18.5 3-1/2 23.8 3-3/4 29.5 4-0/0 37.0 4-1/4 43.6 2-1/2 3-0/0 10.0 3-1/8 12.4 3-1/4 14.9 3-1/2 20.2 3-3/4 26.0 4-0/0 33.5 4-1/2 47.0 5-0/0 63.2 5-1/2 80.3 2-5/8 4-0/0 31.6 2-3/4 3-1/2 16.2 3-3/4 21.8 4-0/0 29.5 4-1/4 36.0 4-1/2 43.0 4-3/4 50.3 3 3-1/2 11.8 3-3/4 17.5 4-0/0 25.2 4-1/4 31.7 4-1/2 38.6 5-0/0 55.1 5-1/2 72.1 3 6-0/0 90.4 6-1/2 110.0 3-1/4 4-1/4 27.0 4-1/2 33.8 5-0/0 50.4 3-1/2 4-0/0 15.4 4-1/2 28.8 5-0/0 45.4 5-1/2 62.4 6-0/0 80.6 6-1/2 100.0 54
CDA 932 Bearing Bronze Hollow Bar 105" Lengths ID OD Wt/Ft ID OD Wt/Ft 3-3/4 5-1/2 57.0 6-0/0 75.1 4 5-0/0 34.1 5-1/2 51.1 6-0/0 69.4 6-1/2 89.2 7-0/0 110.0 5 6-0/0 42.1 6-1/2 61.9 7-0/0 83.3 7-1/2 106.0 8-0/0 131.0 5-1/2 7-0/0 67.3 7-1/2 90.2 4-1/4 5-0/0 27.8 6-0/0 63.1 4-1/2 5-0/0 21.2 5-1/2 38.3 6-0/0 56.5 7-0/0 97.6 Material will conform to SAE 660. Other sizes available upon request. 6 7-0/0 49.8 8-0/0 97.1 6-1/2 7-1/2 53.6 7 8-0/0 57.5 9-0/0 111.0 9-1/2 10-1/2 73.8 55
CDA 932 Bearing Bronze Rounds 105" Lengths Size Wt/Ft Size Wt/Ft 1/2.891 5/8 1.30 3/4 1.90 7/8 2.50 1-0/0 3.20 1-1/8 4.00 1-1/4 5.00 1-3/8 6.10 1-1/2 7.20 1-5/8 8.40 1-3/4 9.96 1-7/8 11.4 2-0/0 13.0 2-1/8 14.5 2-1/4 16.3 2-3/8 18.1 2-1/2 20.0 2-3/4 24.1 3-0/0 28.7 3-1/4 33.6 3-1/2 38.9 3-3/4 44.6 4-0/0 51.6 4-1/4 58.1 4-1/2 65.0 4-3/4 72.2 5-0/0 81.0 5-1/2 98.0 6-0/0 116.0 6-1/2 136.0 7-0/0 157.0 7-1/2 180.0 8-0/0 205.0 9-0/0 258.0 10-0/0 318.0 12-0/0 446.0 Material will also conform to SAE 660. Other sizes available upon request. 56
CDA 932 Bearing Bronze Plate From our Bronze Billet Inventory Saw Cut to Your Specifications The general character of a bronze alloy can be determined by considering the basic constituents, tin and lead. The physical properties increase with an increase in tin content, the anti-friction or self-lubricating qualities increase with an increase in lead content. The relatively equal amounts of tin and lead added to this copper base alloy are designed to achieve an acceptable compromise between strength and machinability. In addition to these qualities, this leaded tin bronze is also well known for its excellent load capacity and resistance to wear. PRECISION SAW CUT FLAT STOCK We can custom saw cut to order any size SAE 660 Bronze plate, square or rectangle up to 10" x 12" x 72" Typical Chemistry Cu Pb Sn Zn 83.0 7.0 7.0 3.0 Conforms to the following specifications: SAE 660 ASTM B 505 QQ-C-390 UNS 93200 Product Data Physical Properties Tensile Strength...............44,000 Yield Strength................27,000 Elongation.....................16% Density........................322 Hardness.......75 BHN (500 kg load) Machinability.....70% (FC Brass=100%) Stress Relieved for Dimensional Stability Only 1/16" Stock Allowance per side required for finish machining Purchase Less Weight No Minimum Quantity 57
CDA 954 Aluminum Bronze Rounds 12' Lengths Size Wt/Ft Size Wt/Ft 1/2.808 3/4 1.70 1-0/0 2.92 1-1/4 4.46 1-1/2 6.32 1-5/8 7.37 1-3/4 8.50 2-0/0 11.0 2-1/4 13.8 2-1/2 17.2 2-3/4 20.7 3-0/0 24.6 3-1/4 28.7 3-1/2 33.5 4-0/0 43.5 4-1/4 49.0 4-1/2 54.8 5-0/0 67.3 5-1/2 81.1 6-0/0 96.3 7-0/0 128.0 8-0/0 167.0 9-0/0 214.0 Other sizes available upon request. This product will meet or exceed all specifications for the following trade name Aluminum Bronze products: Ampco 18, Wearite 224-11, WCI 175. 58
CDA 954 Aluminum Bronze Flats and Squares 12' Lengths Size Wt/Ft Size Wt/Ft 1/4 x 1-0/0 1.27 1-1/4 1.55 1-1/2 1.83 2-0/0 2.41 2-1/2 2.98 3-0/0 3.56 4-0/0 4.71 6 7.06 3/8 x 1-0/0 1.71 1-1/2 2.48 2-0/0 3.26 2-1/2 4.03 3-0/0 4.81 4-0/0 6.37 5-0/0 7.92 1/2 x 1-0/0 2.15 1-1/4 2.64 1-1/2 3.13 1-3/4 3.62 2-0/0 4.11 2-1/2 5.08 3-0/0 6.07 3-1/2 7.04 4-0/0 8.03 6-0/0 12.1 5/8 x 1-0/0 2.60 1-1/2 3.78 2-0/0 4.96 3-0/0 7.32 Other sizes available on request. This product will meet or exceed all specifications for the following trade name Aluminum Bronze products: Ampco 18, Wearite 224-11, WCI 175. 3/4 x 1-0/0 3.04 1-1/2 4.43 2-0/0 5.81 2-1/2 7.19 3-0/0 8.57 4-0/0 11.3 6-0/0 16.9 1 x 1-0/0 3.83 1-1/4 4.83 1-1/2 5.72 1-3/4 6.61 2-0/0 7.50 2-1/2 9.29 3-0/0 11.1 3-1/2 12.9 4-0/0 14.7 6-0/0 21.8 8-0/0 29.0 1-1/4 x 2-0/0 9.20 6-0/0 25.3 1-1/2 x 1-1/2 8.25 2-0/0 10.9 3-0/0 16.1 4-0/0 20.6 5-0/0 26.5 6-0/0 31.7 2 x 2-0/0 14.3 3-0/0 21.1 4-0/0 28.2 6-0/0 41.0 2-1/2 x 3-0/0 26.0 4-0/0 34.7 5-0/0 44.0 3 x 3-0/0 31.7 4- /2 40.5 59
Drill Rod Ground & Polished 3' Lengths Size Wt/3' O-1 W-1 Size Wt/3' O-1 W-1 1/16.031 S S 3/32.070 S S 1/8.125 S S 9/64.158... S 5/32.196 S S 3/8 1.13 S S 13/32 1.33... S 7/16 1.53 S S 1/2 2.00 S S 17/32 2.26... S 11/64.237... S 3/16.282 S S 13/64.331... S 7/32.383 S S 1/4.501 S S 17/64.565... S 9/32.634... S 5/16.782 S S 21/64.863... S 11/32.947... S 9/16 2.54 S S 19/32 2.82... S 5/8 3.13 S S 11/16 3.79 S S 3/4 4.51 S S 7/8 6.13 S S 1 8.01 S S 1-1/4 12.5 S S Other sizes & grades available upon request. 60
Low Carbon Stress Relieved Stripper Plate 6' Lengths Size Wt/Ft Size Wt/Ft 1/4 x 6 5.10 8 6.80 10 8.50 12 10.2 14 11.9 3/8 x 4 5.10 5 6.38 6 7.65 8 10.2 10 12.8 12 15.3 14 17.9 1/2 x 4 6.80 5 8.50 6 10.2 7 11.9 8 13.6 10 17.0 12 20.4 14 23.8 16 27.2 5/8 x 4 8.50 6 12.8 8 17.0 10 21.3 12 25.5 14 29.8 3/4 x 4 10.2 6 15.3 3/4 x 8 20.4 10 25.5 12 30.6 14 35.7 16 40.8 1 x 4 13.6 5 17.0 6 20.4 8 27.2 10 34.0 12 40.8 14 47.6 1-1/4 x 4 17.0 6 25.5 8 34.0 10 42.5 12 51.0 14 59.5 1-1/2 x 4 20.4 6 30.6 8 40.8 10 51.0 12 61.2 14 71.4 2 x 4 27.2 6 40.8 8 54.4 Other sizes available upon request. See Product Date next page. 61
Low Carbon Stress Relieved Stripper Plate 6' Lengths PRODUCT DATA Material Grade: H.R. A-36 Stress Relieved and Flattened Blanchard Ground Top, Bottom and Edges Thickness Tolerance: +/-.003" Width Tolerance: +.005" -.000" Length: 72" Finish: 50/75 Ra typical Typical Chemical Analysis C Mn P S Si.25 max.80/1.20.040 max.05 max.040 max 62
Peterson Steel Corporation COLOR CODES Material............Color C-1018........................Black C-1117.......................Brown C-1215.......................Orange C-1214 Leaded..................Silver C-1117 Leaded..................Gold C-1045.....................Dark Blue C-1141........................White C-1141 Leaded.................Yellow C-1144 Stressproof...............Pink 4150 Annealed..................Green 4150 Heat Treated...............Purple 8620....................Silver & Red 52100.........................Silver Stainless Type 303................Black Stainless Type 304.................Red Stainless Type 316...............Yellow Stainless Type 416...............Green CDA 932 Bearing Bronze.......No Color CDA 954 Aluminum Bronze.......Yellow 0-1 Tool Steel....................Red A-2 Tool Steel...............Light Blue 0-1 Drill Rod.....................Red W-1 Drill Rod..................Yellow Dura-Bar Cast Iron G-1........................Dark Blue G-1A...........................Pink G-2...........................Green 65-45-12......................Yellow 80-55-06...................Light Blue 100-70-02.......................Red H.T.N........................Orange 63
Inches Converted to Decimal Parts of a Foot Inches Decimal of a foot Inches Decimal of a foot Inches Decimal of a foot Inches Decimal of a foot 0....0000 1/16....0052 1/8....0104 3/16....0156 1/4....0208 5/16....0260 3/8....0313 7/16....0365 1/2....0417 9/16....0469 5/8....0521 11/16....0573 3/4....0625 13/16....0677 7/8....0729 15/16....0781 1....0833 1/16....0885 1/8....0937 3/16....0990 1/4....1042 5/16....1094 3/8....1146 7/16....1198 1/2....1250 9/16....1302 5/8....1354 11/16....1406 3/4....1458 13/16....1510 7/8....1562 15/16....1615 2....1667 1/16....1719 1/8....1771 3/16....1823 1/4....1875 5/16....1927 3/8....1979 7/16....2031 1/2....2083 9/16....2135 5/8....2188 11/16....2240 3/4....2292 13/16....2344 7/8....2396 15/16....2448 3....2500 1/16....2552 1/8....2604 3/16....2656 1/4....2708 5/16....2760 3/8....2813 7/16....2865 1/2....2917 9/16....2969 5/8....3021 11/16....3073 3/4....3125 13/16....3177 7/8....3229 15/16....3281 4....3333 1/16....3385 1/8....3437 3/16....3490 1/4....3542 5/16....3594 3/8....3646 7/16....3698 1/2....3750 9/16....3802 5/8....3854 11/16....3906 3/4....3958 13/16....4010 7/8....4062 15/16....4115 5....4167 1/16....4219 1/8....4271 3/16....4323 1/4....4375 5/16....4427 3/8....4479 7/16....4531 1/2....4583 9/16....4635 5/8....4688 11/16....4740 3/4....4792 13/16....4844 7/8....4896 15/16....4948 6....5000 1/16....5052 1/8....5104 3/16....5156 1/4....5208 5/16....5260 3/8....5313 7/16....5365 1/2....5417 9/16....5469 5/8....5521 11/16....5573 3/4....5625 13/16....5677 7/8....5729 15/16....5781 7....5833 1/16....5885 1/8....5937 3/16....5990 1/4....6042 5/16....6094 3/8....6146 7/16....6198 1/2....6250 9/16....6302 5/8....6354 11/16....6406 3/4....6458 13/16....6510 7/8....6562 15/16....6615 8....6667 1/16....6719 1/8....6771 3/16....6823 1/4....6875 5/16....6927 3/8....6979 7/16....7031 1/2....7083 9/16....7135 5/8....7188 11/16....7240 3/4....7292 13/16....7344 7/8....7396 15/16....7448 9....7500 1/16....7552 1/8....7604 3/16....7656 1/4....7708 5/16....7760 3/8....7813 7/16....7865 1/2....7917 9/16....7969 5/8....8021 11/16....8073 3/4....8125 13/16....8177 7/8....8229 15/16....8281 10....8333 1/16....8385 1/8....8437 3/16....8490 1/4....8542 5/16....8594 3/8....8646 7/16....8698 1/2....8750 9/16....8802 5/8....8854 11/16....8906 3/4....8958 13/16....9010 7/8....9062 15/16....9115 11....9167 1/16....9219 1/8....9271 3/16....9323 1/4....9375 5/16....9427 3/8....9479 7/16....9531 1/2....9583 9/16....9635 5/8....9688 11/16....9740 3/4....9792 13/16....9844 7/8....9896 15/16....9948 12... 1.000 64
Notes 65
Notes 66
Notes 67
Notes 68