HydraPressed Slabs Yorkstone Tan Wherefunctionmeetsstyle
Texada This series is named after the rugged and beautiful Gulf Islands of the Pacific Northwest. Texada HydraPressed Slabs have a light shot-blast architectural finish producing subtle colors with a distinctive elegant appearance. Unsealed Sealed Natural Charcoal Desert Sand Tan Green Red Brown HydraPressedslabsarehydraulicallypressedgivingadense,durable,non-slipsurface.
Saturna "Saturna" HydraPressed Slabs receive a deep shot-blast architectural finish exposing the natural hues of the aggregates, creating rich color accents. Unsealed Sealed Natural Charcoal Desert Sand Tan Green Red Brown Thisprocessensuresprecisionsizeswithsquare,trueedgesthatfittogetherperfectly.
Yorkstone "Yorkstone" HydraPressed Slabs receive the Abbotsford Concrete Products' distinctive Pacific Slate finish for the look of natural stone. "Yorkstone" slabs are perfect for pool surrounds, patios or any application that requires a little something extra. Unsealed Sealed courtesy of Five Star Paving Natural Charcoal Desert Sand Tan Green Withthisadvancedmethodofproducingconcretepaving,themixissubjectedto400tonnes
Sandstone "Sandstone" HydraPressed Slabs are created in the same manner as Texada by applying a light shot-blast architectural finish to our Yorkstone. Create unique and beautiful patterns by using a combination of Yorkstone and any of our other HydraPressed Slab Series. The possibilities are yours to imagine. Unsealed Sealed Natural Charcoal Desert Sand Tan Green ofhydraulicpressuregivingstrength,densityanddurabilitycomparabletonaturalstone.
Abbotsford Concrete's On-Site Stormwater Source Control System Abbotsford Concrete Products introduces AquaSlab, paving units for use over full, partial, or no exfiltration base designs. AquaSlabs support pedestrian applications only. AquaSlabs provide drainage through openings in the surface created by vertical slots on the sides of the units. These allow water to enter and flow at rates as high as 354 in./hour (9000 mm/m 2 /hr or 9000 litres/m 2 /hr). 457 mm 254 178 25 25 178 457 mm 254 254 178 25 457 mm available in 42, 50 or 60 mm FindmoredetailsaboutAbbotsfordConcrete'sAquaSlabandAquaPaveOn-
Benefits Lower Construction Costs In conventional drainage design, infiltration and detention facilities are separate from impervious paved areas. AquaSlab On-Site Stormwater Source Control System combines the pavement area, infiltration and detention facilities into one location, allowing more space on the site for incomegenerating buildings. For some designs there can be savings from decreasing or eliminating drain pipes and appurtenances such as inlets and utility structures. AquaSlabs can give you a superior surface at a lower cost than traditional paving methods. With its flat continuous surface, AquaSlabs accept pavement marking materials such as paint and thermal plastic tapes. Reduction of Runoff With an open surface area of about 2%, the openings can infiltrate as much as 354 in./hr (9000 mm/m 2 /hour or 9000 litres/m 2 /hr). The infiltration rate of the crushed stone used for the bedding and base is similar. For design purposes, a conservative 90% reduction in efficiency is generally assumed for infiltration facility design, due to the build-up of sediment over years of service. When considering a 90% reduction of initial infiltration as a typical design assumption, the AquaSlab On-Site Stormwater Source Control System will still capture, treat, infiltrate, and filter rainstorms over 35.4 in./hour (900 mm/m 2 /hr or 900 litres/m 2 /hr). This includes the commonly recurring storms, which generate the most pollution. Roof Water Roof water can be discharged into the sub-base. With gravity fed drainage it is recommended that the water is introduced into the sub-base by means of a sump with a manhole cover adjacent to the paved area. Any debris can be easily caught and cleared. The water is then dispersed within the system via a permavoid distribution tank or perforated outlet pipe. With siphonic drainage, a special chamber is used to disperse the water within the sub-base. Filtering and Treatment of Pollutants Studies of permeable interlocking concrete pavement and its sister practice, infiltration trenches, have shown substantial reduction of non-point source pollutants in runoff. The open-graded crushed stone base has an approximate storage volume of at least 30%. This storage capacity enables a decrease in peak flows and treatment of pollutants, especially nutrients and total suspended solids prior to drainage of the water from the base through drain pipes. Substantial reductions of metals can occur in full or partial base exfiltration designs where the water enters silt and clay soils. Typical AquaSlab Construction Detail Curb/edge restraint with cut-outs for overflow drainage 50mm 150mm AquaSlab 42, 50 or 60 mm Bedding course 5mm clear crush ACP-SC Inbitex Geotextile Sub base 20-5mm aggregate ACP-SC1000 or 2000 Woven Geotextile on bottom and sides of open graded base Soil subgrade-sloped to drain SiteStormwaterSourceControlSysytemat1-800-663-4091oratwww.pavingstones.com
Specialties Abbotsford Concrete Products prides itself in being able to customize to your unique requirements. Our HydraPressed Slabs are available in the following: Standard Sizes: 24" x 24" x 2" 610mm x 610mm x 50mm 18" x 18" x 1-5/8" 457mm x 457mm x 40mm Cut to Sizes: 24" x 12" x 2" 610mm x 305mm x 50mm 18" x 9" x 1-5/8" 457mm x 229mm x 40mm 12" x 12" x 2" 305mm x 305mm x 50mm 9" x 9" x 1-5/8" 229mm x 229mm x 40mm Custom Inlays For those projects that require something a little out of the ordinary, such as special sizing or custom coloring, please contact your Abbotsford Concrete representative for assistance. HydraPressed Drains ADA* HydraPressed Slab *(American Disabilities Act) Interior Application Specialsizing,customcolors,decorativeshot-blastpatternsareavailabletomakeyourprojectunique.
HydraPressed Slab Installation Details: - Mortar Set HydraPressed Paving Slabs Thinset Zero Slump Mortar Bed w/reinforcing Mesh Waterproofing System (by others) Structural Concrete Sand Set HydraPressed Paving Slabs 3/4-1 Sand Setting Bed (Washed Concrete Sand) 6-8 Compacted Aggregate Base (3/4 Minus Roadbase Material )
HydraPressed Slab Roof Installation using pedestals with HydraPressed Paving Slabs are used for pedestrian traffic or in areas where light maintenance vehicles (ie. golf carts) operate. HydraPressed Paving Slabs are installed on sand, mortar, or pedestal systems, for patios, plaza decks, roof tops, or any other type of pedestrian walking surface. Overview HydraPressed Paving Slabs Pedestals Extruded Polystyrene Insulation Protection Board and/or Drain Mat Waterproofing Membrane Structural Concrete Pedestal systems are designed for use over pitched surfaces. These systems ensure precise HydraPressed Slab alignment and even spacing to allow for drainage and air circulation which are critical to the health of any deck installed over a waterproof membrane. This type of segmental system allows for ease of access for repairs or annual maintenance to the subsurface without damage to the HydraPressed Slabs. Note: When specifying these types of built-up roof systems, be sure to consult the waterproofing manufacturers design details and specifications. Forplazaorrooftopinstallations,cautionshouldbeexercisedwithrespect
various waterproofing systems Modified Bitumen HydraPressed Paving Slabs Pedestals Extruded Polystyrene Insulation (Optional) Protection Board and/or Drain Mat Waterproofing Membrane (ie, peel & stick, BUR, APP or SBS) Primer Structural Concrete Hot Rubber HydraPressed Paving Slabs Pedestals Extruded Polystyrene Insulation (Optional) Protection Board and/or Drain Mat Hot Applied Membrane Reinforcing Fabric Hot Applied Membrane Primer Structural Concrete Single Ply Sheet Membrane HydraPressed Paving Slabs Pedestals Extruded Polystyrene Insulation (Optional) Protection Board and/or Drain Mat Waterproofing Membrane (ie, EPDM, PVC, TPO or CSPE) Structural Concrete totheweightoftheproductaswellasthewindvelocitiesintheareasofuse.
HydraPressed Paving Slab Specifications 1.0 Qualifications: The manufacturer is to be prequalified by the specifier, with the manufacturer having a minimum of 5 years experience in precast concrete pavers, and specialty products. 2.0 References: Materials must conform to the following ASTM and CSA Standards: A) ASTM 150, CSA A5 : Specification for Portland Cement B) ASTM C33, CSA A23.1 : Specification for Normal Weight Aggregates C) ASTM C979 : Specification for Pigments D) ASTM C140, CSA A231.1-99 : Specification for Compressive Strength E) CSA A231.1-99 : Specification for Flexural Strength F) ASTM C140, CSA A231.1-99 : Specification for Water Absorption G) CSA A231.1-99 : Specification Freeze/Thaw 3.0 Technical Specifications: Compressive Strength: Average compressive strength shall not be less than 8000 PSI (55 MPA) with no individual unit less than 7300 PSI (50 MPA) when tested not less than 28 days from the date of production in accordance with ASTM C140, or CSA A231.1-99. Flexural Strength: Average flexural (transverse) strength of the concrete paving slabs shall be at least 655 PSI (4.5 MPA) with no individual unit below 582 PSI (4.0 MPA) when tested in accordance with CSA A231.1 99. Water Absorption: Average water absorption shall not be greater than five percent (5%) with no individual unit greater than seven percent (7%), when tested in accordance with ASTM C140. CSA A231.1 99. Scaling Resistance: Specimens shall not have an average loss of mass greater than 300 g/m2 of the total inundated surface area of the individual paving slab after 28 cycles of freezing and thawing, 800 g/m2 after 49 cycles. Specimens with an architectural finish shall not have an average loss of mass greater than 500 g/m2 of the total inundated surface area of the individual paving slab after 28 cycles of freezing and thawing, or 1200 g/m2 after 49 cycles. When tested in accordance with CSA A231.1 99. Dimensions: Dimensions of paving slabs and concave or convex warpage shall not differ from those agreed upon by the manufacturer by more than the following amounts: a) Length and width: -1.0 mm to + 2.0 mm b) Height +_ 3.0 mm c) Concave or convex warpage in one dimension by the following amounts: i) up to 450 mm, 2.0 mm; or ii) over 450 mm, 3.0 mm. Dimensions are based on manufacturer s standard drawings for the particular shape identified. Center Point Load Test of Pedestal-supported Slabs: 1,800 lbs. 3.1 Test Results: Documentation for the test results is on file and available upon request. 3.2 Technical Services: Technical service representatives are available to assist with project design, paver selection, installation recommendations, or any other technical concerns you may have. Contact: ABBOTSFORD CONCRETE PRODUCTS Toll free at 1-800-663-4091. 4.0 Submittals: Two matched samples shall be used to determine the color and texture, one to be retained by the specifier, and the other by the manufacturer, to ensure the correct paver is provided to the project. 5.0 Installation: Qualified installers must show successful completion of three (3) similar sized project applications within the last three (3) years. The installer shall assign mechanics from these earlier applications, one of whom shall serve as lead mechanic. Installers not meeting this criteria shall require approval from the specifier or manufacturer prior to installation. 6.0 Maintenance: This product requires low maintenance. As the product is removable, it allows for easy maintenance to substrate as well as easy replacement of damaged pavers. A high-pressure wash is recommended from time to time, with drains being cleaned regularly. 7.0 Warranty: Abbotsford Concrete Products provides a manufacturer s warranty ensuring material specification compliance. Manufactured by Toll Free: 1-800-663-4091 Visit our website at www.pavingstones.com for complete design details and photo gallery