NanaWall Matching Windows and Doors Table of Contents

NanaWall Matching Windows and Doors Table of Contents Matching Windows and Doors Cross Sections and Maximum Frame Charts Introduction.............................................................. 1 NanaWall French Doors....................................................2 Performance and Testing Results............................................3 Maximum Frame Height Chart Fixed Panel.........................................................7 Tilt Turn Window / Door................................................8 NanaWall WA68 - Aluminum Clad Wood Fixed Panel and Tilt Turn Window / Door...9 NanaWall WD68 - Wood Framed Fixed Panel and Tilt Turn Window / Door.........11 NanaWall SL48 - Aluminum Framed Fixed Panel and Tilt Turn Window / Door......13 NanaWall SL88 - Thermally Broken Aluminum Framed Fixed Panel and Tilt Turn Window / Door with HVHZ Option....................................15 NanaWall SL68 - Thermally Broken Aluminum Framed Fixed Panel and Tilt Turn Window / Door....................................................17 Specifications............................................................19 SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com i

NanaWall Matching Windows and Doors Introduction Coordinated Walls Available are matching systems in aluminum-clad wood, wood, standard aluminum and thermally broken aluminum. Depending on sizes and wind load requirements, matching systems can be mulled (with appropriate structural support) with folding and individual panel sliding system. Fixed Windows and Storefront Fixed units are available for transoms above a folding or individual panel sliding unit. Center lines can be lined up. Sidelites are available with frame extenders so that horizontal glass lines are approximately the same. Complete storefronts are also available with a combination of mulled units. NanaWall Tilt Windows and Doors Available are tilt-turn windows, tilt-turn doors and tilt-only hopper windows. These systems are engineered to provide high weather resistance and structural performance, suitable for many high-rise structures and buildings in hurricane and other areas. Florida Approval SL88 thermally broken aluminum framed tilt turn window with frame size of 48" wide x 72" high is Florida state wide approved with Product Approval number FL16047. It is also approved for use in the high velocity hurricane zone (HVHZ) with impact glass. This information with limitations can be viewed at www. floridabuilding.org. Performance Testing The tested sample unit of the SL 68 thermally broken aluminum framed tilt turn window met the performance requirements of AAMA DAW-C90 1219 x 1829 (48x72) /DA-C100 48x72 rating. The tested sample unit of the SL 88 thermally broken aluminum framed tilt turn window met the performance requirements of AAMA DAW-C70 1219 x 1829 (48x72)/DA-C70 48x72 rating. The tested sample unit of the WA68 aluminum-clad wood framed tilt turn window met the performance requirements of AAMA DAW-C50 1122x1822 (48x72). The tested sample unit of the WD 68 wood framed tilt turn window met the performance requirements of AAMA DAW-C70 1220x1828 (48x72). See Performance pages for details. Benefits of NanaWall Tilt Systems With tilt-turn hardware, large size operable openings are possible. Tilts Inward for Safe Ventilation. The tilt position opens up from the top, tilting in a few inches, for safe ventilation. Turns Inward for Easy Cleaning. With the turn position, the window swings in on its hinges to make cleaning the outside surface easy. For units used as transoms, tilt-only hopper windows can be supplied with operators so that high units can be easily opened and closed. NOTICE For mulled fixed or tilt turn units or a combination of different units, please consult with a qualified structural engineer to determine, based on project design wind loads and other requirements, if any structural stiffeners are needed between units. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 1

NanaWall Matching Windows and Doors Introduction NanaWall French Doors NanaWall French doors are available as single doors or pairs. Very narrow stiles and rails are possible. NanaWall French doors use exactly the same profiles and hardware as the matching NanaWall folding system. Hence, the same size charts, glazing options, wood/finish options and finish hardware options as the matching NanaWall folding system are applicable. The same testing performance results also apply (within a folding system, with an odd number of panels stacking to one side, the last panel is a swing door). For aluminum-clad, wood framed French doors, see WA67. For wood framed French doors, see WD66 and WD65. For standard aluminum framed French doors, see SL45. For thermally broken aluminum framed French doors, see SL60 and SL70. For Miami Dade / AAMA hurricane thermally broken aluminum framed French doors, see SL73. For structurally glazed aluminum framed French doors, see SL82. Technical Description The corresponding closest system match to NanaWall folding/sliding systems are as follows: Folding/sliding system WA67 WD65, WD66, HSW66 SL45, HSW45 SL60, HSW60 SL70 Corresponding matching fixed/tilt turn system WA68 WD68 SL48 SL68 SL88 Profile and Finish Options For WD 68 and WA 68 systems, standard woods available are Douglas Fir, Pine, or Meranti. Other woods are also available. Frames and panels have a sanding sealer or a base coat applied or for WA 68 system only, with one additional clear coat; see Wood Finish Options in the General Introduction. Standard aluminum finishes for the WA68, SL48 and SL88 systems are clear anodized and the 50 finishes shown in the NanaWall Powder Coating Finish Chart in the front of this binder. Powder coated finishes can be chosen from a range of over two hundred RAL colors; see Aluminum Finish Options in the General Introduction. Glazing Units are supplied glazed with double clear insulating safety, insulating Low-E safety glass, single (for SL48 and WD 68 systems only), other high performing safety glass such as triple glazing, Heat Mirror, special tint, etc., or other glass on request. Hinge Cover Options Covers for hinges can be white, brown or silver. Handle Options Standard: Stainless steel in brushed satin or black titanium finishes. Optional: Nylon available in white, dark brown or gray color or solid brass available in white, oil rubbed brass or satin nickel finishes. See "Hardware" in the General Introduction for other options. 2 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

NanaWall Matching Windows and Doors Performance SL68 Thermally Broken Aluminum Framed Tilt Turn Window/Door Performance Testing Results Type of Test Result *Air Infiltration: ASTM E-283, cfm/ft 2 @1.6 psf (75 Pa): 0.04 (.20 L/s/m 2 ) @6.20 psf (300 Pa): 0.11 (.56 L/s/m 2 ) *Water Penetration: ASTM E547 and E331 * Structural Load Deflection ASTM E-330: Pass Note that the structural test pressures were 50% higher than the design pressures. No uncontrolled water entry @ 13.5 psf (645 Pa) Design Pressure Positive: @100 psf (4800 Pa) Design Pressure Negative: @110 psf (5270 Pa) *Forced Entry Resistance In accordance with ASTM F 588 * Excerpts of results of a 4 0 W x 6 0 H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory in August 2006, in accordance with AAMA/WDMA/CSA 101/I.S.2/A440-05 and AAMA/NWWDA 101/I.S.2-97 standards. The sample tested met the performance requirements for a DAW-C90 1219 x 1829 (48 x 72)/DA-C100 48x72 rating. Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4 0 W x 6 0 H Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for restrictions. Positive Design Pressure Negative Design Pressure 250 250 245 245 240 240 235 235 230 230 225 225 220 220 215 215 210 210 205 205 Allowable Design Wind Loading - PSF 200 195 190 185 180 175 170 165 160 155 150 145 140 135 130 1 11 2 3 Frame Width Allowable Design Wind Loading - PSF 200 195 190 185 180 175 170 165 160 155 150 145 140 135 130 1 11 2 3 2 7 Frame Width 125 125 120 2 7 120 2 11 115 115 110 2 11 110 3 3 105 105 3 7 100 95 90 3 3 3 7 3 11 100 95 90 3 11 4 3 85 4 3 3 0 3 6 4 0 4 6 5 0 5 6 6 0 6 6 7 0 7 6 8 0 8 6 85 3 0 3 6 4 0 4 6 5 0 5 6 6 0 6 6 7 0 7 6 8 0 8 6 Frame Height See Maximum Frame Size Chart for Possible Sizes Frame Height See Maximum Frame Size Chart for Possible Sizes Please also note that chart is only applicable for units with referenced NanaWall supplied locking. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 3

NanaWall Matching Windows and Doors Performance SL88 Thermally Broken Aluminum Framed Tilt Turn Window/Door High Velocity Hurricane Zone (HVHZ) rated with Impact Glass with FL Product Approval # 16047 Type of Test Performance Testing Results Result *Air Infiltration: Protocol TAS 202 and ASTM E-283, cfm/ft 2 @1.60 psf (75 Pa): 0.09 @6.20 psf (300 Pa): 0.25 *Water Penetration: Protocol TAS 202, ASTM E547 and E331 * Structural Load Deflection Protocol TAS 202 and ASTM E-330: Pass Note that the structural test pressures were 50% higher than the design pressures. Missile Impact & Cycling: Protocols TAS 201 & 203, ASTM E 1886 and E 1996 No uncontrolled water entry @ 13.5 psf (645 Pa) Design Pressure Positive: @70 psf (3350 Pa) Design Pressure Negative: @100 psf (4785 Pa) WITH 1 1/8" INSULATED IMPACT GLASS Design Pressure Positive: @ 90 psf (4300 Pa) Design Pressure Negative: @ 120 psf (5260 Pa) *Forced Entry Resistance In accordance with ASTM F 588 * Excerpts of results of three separate units with sizes of 4 0 W x 6 0 H tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory, in October 2010. Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4 0 W x 6 0 H Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for restrictions. Allowable Design Wind Loading - PSF 90 88 86 84 82 80 78 76 74 72 70 68 66 64 62 Positive Design Pressure 60 58 3 0 3 6 4 0 4 6 5 0 5 6 6 0 6 6 7 0 7 6 8 0 4 3 8 6 Frame Height See Maximum Frame Size Chart for Possible Sizes Max. limited to cycling pressure 2 7 2 11 3 3 3 7 3 11 Frame Width Allowable Design Wind Loading - PSF 120 118 116 114 112 110 108 106 104 102 100 98 96 94 92 90 88 86 84 Negative Design Pressure 82 3 0 3 6 4 0 4 6 5 0 5 6 6 0 6 6 7 0 7 6 8 0 8 6 Frame Height See Maximum Frame Size Chart for Possible Sizes Max. limited to cycling pressure 2 11 3 3 3 7 3 11 4 3 Frame Width Please also note that chart is only applicable for units with referenced NanaWall supplied locking. 4 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

NanaWall Matching Windows and Doors Performance WA68 Aluminum Clad Wood Framed Tilt Turn Window/Door Performance Testing Results Type of Test Result *Air Infiltration: ASTM E-283, cfm/ft 2 @1.6 psf (75 Pa): 0.01 (.1 L/s/m 2 ) @6.20 psf (300 Pa): 0.15 (.8 L/s/m 2 ) *Water Penetration: ASTM E547 and E331 * Structural Load Deflection ASTM E-330: Pass Note that the structural test pressures were 50% higher than the design pressures. *Forced Entry Resistance No uncontrolled water entry @ 12 psf ( 580 Pa) Design Pressure Positive: @50 psf (2400 Pa) Design Pressure Negative: @70 psf (3360 Pa) In accordance with ASTM F 588 - Grade 20 & CAWM 301 * Excerpts of results of a 4 0 W x 6 0 H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory in January 2008, in accordance with AAMA/WDMA/CSA 101/I.S.2/A440-05 standard. The sample tested met the performance requirements for a DAW-C50 1220 x 1822 (48 x 72) rating. Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4 0 W x 6 0 H Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for restrictions. Positive Design Pressure Negative Design Pressure 105 145 100 140 95 135 Allowable Design Wind Loading - PSF 90 85 80 75 70 65 60 55 50 45 40 35 30 25 20 15 1 11 2 3 2 7 2 11 3 3 3 7 3 11 4 3 Frame Width Allowable Design Wind Loading - PSF 130 125 120 115 110 105 100 95 90 85 80 75 70 65 60 55 1 11 2 3 2 7 2 11 3 3 3 7 3 11 4 3 Frame Width 50 3 0 3 6 4 0 4 6 5 0 5 6 6 0 6 6 7 0 7 6 8 0 8 6 3 0 3 6 4 0 4 6 5 0 5 6 6 0 6 6 7 0 7 6 8 0 8 6 Frame Height See Maximum Frame Size Chart for Possible Sizes Frame Height See Maximum Frame Size Chart for Possible Sizes Please also note that chart is only applicable for units with referenced NanaWall supplied locking. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 5

NanaWall Matching Windows and Doors Performance WD68 Wood Framed Tilt Turn Window/Door Performance Testing Results Type of Test Result *Air Infiltration: ASTM E-283, cfm/ft 2 @1.60 psf (75 Pa): 0.01 (.1 L/s/m 2 ) @6.20 psf (300 Pa): 0.01 (.1 L/s/m 2 ) *Water Penetration: ASTM E547 and E331 No uncontrolled water entry @ 13.5 psf (645 Pa) * Structural Load Deflection ASTM E-330: Pass Note that the structural test pressures were 50% higher than the design pressures. *Forced Entry Resistance Design Pressure Positive: @70 psf (3360 Pa) Design Pressure Negative: @120 psf (5745 Pa) In accordance with ASTM F 588 - Grade 20 & CAWM 301 * Excerpts of results of a 4 0 W x 6 0 H standard unit tested by Architectural Testing, Inc., Fresno, CA, an independent testing laboratory in January 2008, in accordance with AAMA/WDMA/CSA 101/I.S.2/A440-05 standard. The sample tested met the performance requirements for a DAW-C70 1220 x 1828 (48 x 72) rating. Design Windload Charts (Derived from Comparative Analysis) Test unit size: 4 0 W x 6 0 H Please note that some jurisdictions may limit the use of these charts or may not accept them at all. Design pressures and/ or sizes may be restricted to what was tested. For Florida approved products, please see detailed FL Evaluation Report for restrictions. Positive Design Pressure Negative Design Pressure 145 250 140 245 135 240 Allowable Design Wind Loading - PSF 130 125 120 115 110 105 100 95 90 85 80 75 70 65 60 55 50 3 0 3 6 4 0 4 6 5 0 5 6 6 0 6 6 7 0 7 6 8 0 8 6 Frame Height See Maximum Frame Size Chart for Possible Sizes 1 11 2 3 2 7 2 11 3 3 3 7 3 11 4 3 Frame Width Allowable Design Wind Loading - PSF 235 230 225 220 215 210 205 200 195 190 185 180 175 170 165 160 155 150 145 140 135 130 1 11 2 3 2 7 2 11 Frame Width 125 120 3 3 115 3 7 Please also note that chart is only applicable for units with referenced NanaWall supplied locking. 110 105 100 95 90 3 11 4 3 85 3 0 3 6 4 0 4 6 5 0 5 6 6 0 6 6 7 0 7 6 8 0 8 6 Frame Height See Maximum Frame Size Chart for Possible Sizes 6 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

NanaWall Matching Windows and Doors Size Chart NanaWall Maximum Frame Size Chart Fixed Panel WA68, WD68, SL48, SL68, SL88 9 10 (3000) Any custom size is possible up to the maximum size shown. NOTE: English dimensions are approximate. Dimensions in parenthesis are in millimeters 9 2 (2800) 8 6 (2600) Frame Height of Unit 7 10 (2400) 7 2 (2200) 6 6 (2000) 5 11 (1800) 5 3 (1600) 4 7 (1400) 3 11 (1200) 3 3 (1000) 1 11 2 7 3 3 3 11 4 7 5 3 5 11 6 6 7 2 (600) (800) (1000) (1200) (1400) (1600) (1800) (2000) (2200) Frame Width of Unit Solid dark line on chart indicates maximum frame height possible for a given maximum frame width. The maximum size limits shown are based on the weight of a unit that has a net glass thickness of 5/16 (8mm). The composition of standard insulated glass is 5/32 glass/air space/ 5/32 glass. For other net glass thicknesses, this maximum size chart may not apply. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 7

NanaWall Matching Windows and Doors Size Chart NanaWall Maximum Frame Size Chart Tilt Turn Window/Door WA68, WD68, SL48, SL68, SL88 Any custom size is possible up to the maximum size shown. NOTE: English dimensions are approximate. Dimensions in parenthesis are in millimeters 8 2 (2500) 7 10 (2400) 7 7 (2300) 7 3 (2200) 6 11 (2100) 6 7 (2000) Frame Height of Unit 6 3 (1900) 5 11 (1800) 5 7 (1700) 5 3 (1600) 4 11 (1500) 4 7 (1400) 4 3 (1300) 3 11 (1200) 3 7 (1100) 3 3 (1000) 1 11 2 3 2 7 2 11 3 3 3 7 3 11 4 3 4 7 4 11 5 3 (600) (700) (800) (900) (1000) (1100) (1200) (1300) (1400) (1500) (1600) Frame Width of Unit Solid dark line on chart indicates maximum frame height possible for a given maximum frame width. The maximum size limits shown are based on the weight of a unit that has a net glass thickness of 5/16 (8mm). The composition of standard insulated glass is 5/32 glass/ air space/ 5/32 glass. For other net glass thicknesses, this maximum size chart may not apply. 8 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

NanaWall Matching Windows and Doors NanaWall WA68 Fixed Panel All Cross-Sectional Views Are Half Size Vertical Cross-Section Wood frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 9

NanaWall Matching Windows and Doors NanaWall WA68 Tilt Turn Window (Available as a single window or as a pair. In a pair, only one panel can tilt). All Cross-Sectional Views Are Half Size. Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR 10 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

NanaWall Matching Windows and Doors NanaWall WD68 Fixed Panel All Cross-Sectional Views Are Half Size Vertical Cross-Section Wood frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 11

NanaWall Matching Windows and Doors NanaWall WD68 Tilt Turn Window (Available as a single window or multiple unit). All Cross- Sectional Views Are Half Size Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR 12 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

NanaWall Matching Windows and Doors NanaWall SL48 Fixed Panel All Cross-Sectional Views Are Half Size Vertical Cross-Section Aluminum frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 13

NanaWall Matching Windows and Doors NanaWall SL48 Tilt Turn Window All Cross-Sectional Views Are Half Size. (Available as a single window or as a pair. In a pair, only one panel can tilt.) Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR 14 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

NanaWall Matching Windows and Doors NanaWall SL88 Thermally Broken Fixed Panel All Cross-Sectional Views Are Half Size. Vertical Cross-Section Aluminum frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 15

NanaWall Matching Windows and Doors NanaWall SL88 Thermally Broken Tilt Turn Window (Available as a single window or as a pair. In a pair, only one panel can tilt.) All Cross-Sectional Views Are Half Size. High Velocity Hurricane Zone (HVHZ) rated with Impact Glass with FL Product Approval # 16047 Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR 16 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

NanaWall Matching Windows and Doors NanaWall SL68 Thermally Broken Fixed Panel All Cross-Sectional Views Are Half Size. Vertical Cross-Section Aluminum frame extenders are available to approximately align glass sight lines to adjacent folding or sliding systems. EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 17

NanaWall Matching Windows and Doors NanaWall SL68 Thermally Broken Tilt Turn Window (Available as a single window or as a pair. In a pair, only one panel can tilt.) All Cross-Sectional Views Are Half Size. Vertical Cross-Section EXTERIOR INTERIOR Horizontal Cross-Section EXTERIOR INTERIOR 18 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

Guide Specifications NanaWall Matching Windows and Doors Guide Specifications - Section 085200: NanaWall SL88 Thermally Broken Aluminum Framed Dual Action Tilt Turn Window PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping, glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown on drawings and specifi ed herein, with NanaWall SL88, the Thermally Broken Aluminum Framed Dual Action Tilt Turn Window as supplied by NANA WALL SYSTEMS, INC. 1.02 REFERENCES A. FL Building Code Compliance Offi ce Protocol: 1. TAS 201, Impact Test Procedures 2. TAS 202, Criteria for Testing Impact and Non Impact Resistant Building Envelope Components Using Uniform Static Air Pressure 3. TAS 203, Criteria for Testing Products Subject to Cyclic Wind Pressure Loading. B. A. American Architectural Manufacturers Association (AAMA): 1. 4. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights. 2. 5. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum. 3. 6. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels.. C. B. American National Standards Institute (ANSI): 1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Buildings. D. C. American Society for Testing and Materials (ASTM): 1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 3. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference. 4. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential. 5. ASTM F 588, Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies. E. D. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials. 1.03 SUBMITTALS A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and handle height. B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 19

NanaWall Matching Windows and Doors Guide Specifications completion date, type and size of unit installed. 1.04 QUALITY ASSURANCE A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufacturer with at least 25 years experience in providing fenestration systems in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. 2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005 standard. B. Performance Requirements: Provide from manufacturer that has independently tested typical units per AAMA/ WDMA/CSA 101/I.S.2/A440 Testing results to include air infi ltration in accordance with ASTM E 283, water penetration in accordance with ASTM E 331 and ASTM E 547, structural loading in accordance with ASTM E 330 and forced entry in accordance with ASTM F 588. C. Performance Criteria with Impact Glass: The SL88 is approved for High Velocity Hurricane Zone (HVHZ) with Impact Glass with FL Product Approval # 16047 ** SPECIFIER NOTE: Structural load testing results are only applicable for the test unit size. (Comparative analysis charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures specifi cally required for the project. Check for limitations on the use of these charts in the jurisdiction of the project). See manufacturer's latest published data. D. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestration products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers of General Contractor and Owner's contact person. 1.05 WARRANTY A. Provide manufacturer's standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer. 1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the following: 1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. B. Do not use forced heat to dry out building. C. Store fl at in dry, well ventilated area out of direct sunlight. PART 2 PRODUCTS 2.01 SUPPLIER A. NANA WALL SYSTEMS, INC. - SL88 100 Meadow Creek Drive, Corte Madera, CA 94925 Toll Free: (800) 873-5673 Telephone: (415) 383-3148 Fax: (415) 383-0312 Website: www.nanawall.com Email: info@nanawall.com 20 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

Guide Specifications NanaWall Matching Windows and Doors B. Other suppliers equal to the specifi ed product must submit substitution request two weeks before bid for prior approval. 2.02 MATERIALS A. Frame and Sash: From manufacturer s standard profi les, provide frame, sash and glazing stops with dimensions shown on drawings. 1. Provide Sash with: Standard one lite [OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 2. Aluminum Extrusion: Extrusions with nominal thickness of.078 (2.0 mm). Alloy specifi ed as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611 or powder coated conforming to AAMA 2604 3. Thermally broken with ¾ -15/16 (20-24 mm) polyamide plastic reinforced with glass fi bers with additional insulating foam. 4. Aluminum Finish: B. Glass: Select from NanaWall Powder Coating Finish Chart [OR clear anodized] [OR dark bronze anodized] [OR select from range of RAL high gloss powder coated fi nishes available from manufacturer] [OR select from range of RAL matte powder coated fi nishes available from manufacturer] [OR select from range of Wood Grain powder coated fi nish] [OR custom fi nish]. Same [OR different] fi nishes on inside and outside. 1. Provide manufacturer s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 120 15/16 (24 mm) insulating clear safety [OR 15/16 (24 mm) double glazed insulating argon fi lled Low-E safety] [OR 1 ½ (38 mm triple glazed insulating argon fi lled Low-E safety] [OR other glass available from manufacturer]. 2. Provide manufacturer s standard glass spacers. Provide without capillary tubes [OR with capillary tubes]. C. Tilt Turn Hardware 1. Provide manufacturer s standard cam type multipoint locking mechanism. a. The concealed multipoint locking mechanism shall be driven by a single locking handle. 2. Provide manufacturer s standard hinges, pins, strikes, and limit stays. 3. Handles: Stainless steel window handles in a titanium black fi nish [OR stainless steel window handles in a brushed satin fi nish] SPECIFIER S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other suppliers. Provide handle height centered [OR at 41 3/8 from bottom of panel] [OR as specifi ed from bottom of SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 21

NanaWall Matching Windows and Doors Guide Specifications panel]. D. Weather stripping: Provide manufacturer s standard double layer EPDM 2.03 FABRICATION A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles, glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right] 2.04 ACCESSORIES (Edit for project requirements.) A. Provide insect screen. Mesh in gray [Or black] Provide screen frame in aluminum: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR powder coated select from range of RAL powder coated fi nishes available from manufacturer]. B. Provide other side lites, transoms as per drawings provided. PART 3 EXECUTION 3.01 ERECTION A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity of the header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span. B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no unevenness, bowing, or bumps on the fl oor. C. Installation of units constitutes acceptance of existing conditions. 3.02 INSTALLATION A. Install frame in accordance with manufacturer s recommendations and installation instructions. Properly fl ash and waterproof around the perimeter of the opening. B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work. C. Install sash and handles in accordance with manufacturer s recommendations and installation instructions. D. If necessary, adjust hardware for proper operation. E. Accessories: Screens; install in accordance with screen manufacturer s recommendations and installation instructions. END OF SECTION DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not intended to be verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the particular requirements of a specifi c construction project. 22 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

Guide Specifications NanaWall Matching Windows and Doors Guide Specifications - Section 085200 NanaWall SL48 Aluminum Framed Dual Action Tilt Turn Window PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping, glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown on drawings and specifi ed herein, with NanaWall SL48, the Aluminum Framed Dual Action Tilt Turn Window as supplied by NANA WALL SYSTEMS, INC. 1.02 REFERENCES A. American Architectural Manufacturers Association (AAMA): 1. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights. 2. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum. 3. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels. B. American National Standards Institute (ANSI): 1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Buildings. C. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials. 1.03 SUBMITTALS A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and handle height. B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and completion date, type and size of unit installed. 1.04 QUALITY ASSURANCE A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufacturer with at least 25 years experience in providing fenestration systems in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. 2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005 standard. B. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestration products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers of General Contractor and Owner's contact person. 1.05 WARRANTY A. Provide manufacturer's standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer. 1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the following: SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 23

NanaWall Matching Windows and Doors Guide Specifications 1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. B. Do not use forced heat to dry out building. C. Store fl at in dry, well ventilated area out of direct sunlight. PART 2 PRODUCTS 2.01 SUPPLIER A. NANA WALL SYSTEMS, INC. - SL48 100 Meadow Creek Drive, Corte Madera, CA 94925 Toll Free: (800) 873-5673 Telephone: (415) 383-3148 Fax: (415) 383-0312 Website: www.nanawall.com Email: info@nanawall.com B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior approval. 2.02 MATERIALS A. Frame and Sash: From manufacturer s standard profi les, provide frame, sash and glazing stops with dimensions shown on drawings. 1. Provide Sash with: Standard one lite [OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 2. Aluminum Extrusion: Extrusions with nominal thickness of.078 (2.0 mm). Alloy specifi ed as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611.98 or powder coated conforming to AAMA 2604 3. Aluminum Finish: B. Glass: Select from NanaWall Powder Coating Finish Chart [OR dark bronze anodized] [OR clear anodized] [OR select from range of RAL high gloss powder coated fi nishes available from manufacturer] [OR select from range of RAL matte powder coated fi nishes available from manufacturer] [OR custom fi nish]. 1. Provide manufacturer s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 120 1/4 (6 mm) tempered [OR ¼ (6 mm) laminated] [OR ¾ (20 mm) insulating clear safety] [OR ¾ (20 mm) double glazed insulating argon fi lled Low-E safety] [OR other glass available from manufacturer]. 2. For insulated units, provide manufacturer s standard glass spacers. Provide without capillary tubes [OR with capillary tubes]. C. Tilt Turn Hardware 1. Provide manufacturer s standard cam type multipoint locking mechanism. 24 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

Guide Specifications NanaWall Matching Windows and Doors a. The concealed multipoint locking mechanism shall be driven by a single locking handle. 2. Provide manufacturer s standard hinges, pins, strikes, and limit stays. 3. Handles: Stainless steel window handles in a titanium black fi nish [OR stainless steel window handles in a brushed satin fi nish] SPECIFIER S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other suppliers. D. Provide handle height centered [OR at 41 3/8 from bottom of panel] [OR as specifi ed from bottom of panel]. E. Weather stripping: Provide manufacturer s standard double layer EPDM 2.03 FABRICATION A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles, glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right] 2.04 ACCESSORIES (Edit for project requirements.) A. Provide insect screen. Mesh in gray [Or black] Provide screen frame in aluminum: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR powder coated select from range of RAL powder coated fi nishes available from manufacturer]. B. Provide other side lites, transoms as per drawings provided. PART 3 EXECUTION 3.01 ERECTION A. Because of the large dimensions involved and the weight and movement of the sash, verify the structural integrity of the header such that the maximum defl ection with live and dead loads is limited to be the L/720 of the span. B. Examine surfaces of openings and verify dimensions; verify rough openings are level, plumb, and square, with no unevenness, bowing, or bumps on the fl oor. C. Installation of units constitutes acceptance of existing conditions. 3.02 INSTALLATION A. Install frame in accordance with manufacturer s recommendations and installation instructions. Properly fl ash and waterproof around the perimeter of the opening. B. Installer to provide appropriate anchorage devices and to securely and rigidly fi t frame in place, absolutely level, straight, plumb and square. Install frame in proper elevation, plane and location, and in proper alignment with other work. C. Install sash and handles in accordance with manufacturer s recommendations and installation instructions. D. If necessary, adjust hardware for proper operation. E. Accessories: Screens; install in accordance with screen manufacturer s recommendations and installation instructions. END OF SECTION SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 25

NanaWall Matching Windows and Doors Guide Specifications DISCLAIMER: Nana Wall Systems, Inc. takes no responsibility for product selection or application, including, but not limited to, compliance with building codes, safety codes, laws, or fi tness for a particular purpose. The guide specifi cations is not intended to be verbatim as a project specifi cation without appropriate modifi cations for the specifi c use intended and the particular requirements of a specifi c construction project. THIS PAGE BLANK 26 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

Guide Specifications NanaWall Matching Windows and Doors Guide Specifications - Section 085200 NanaWall SL68 Thermally Broken Aluminum Framed Dual Action Tilt Turn Window PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Inswing casement, tilt turn in frame and sash, tilt turn hardware, handles, weather stripping, glass and glazing; designed to provide a dual action tilt turn window/door, with sizes and confi gurations as shown on drawings and specifi ed herein, with NanaWall SL68, the Thermally Broken Aluminum Framed Dual Action Tilt Turn Window as supplied by NANA WALL SYSTEMS, INC. 1.02 REFERENCES A. American Architectural Manufacturers Association (AAMA): 1. AAMA/WDMA/CSA 101/I.S.2/A440-05, Standard Specifi cation for Windows, Doors, and Unit Skylights. 2. AAMA 611, Voluntary Specifi cation for Anodized Architectural Aluminum. 3. AAMA 2604, Voluntary Specifi cations, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels.. B. American National Standards Institute (ANSI): 1. ANSI Z97.1, Safety Performance Specifi cations and Methods of Test for Safety Glazing Material Used In Buildings. C. American Society for Testing and Materials (ASTM): 1. ASTM E 283, Test Method for Rate of Air Leakage through Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 2. ASTM E 330, Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. 3. ASTM E 331, Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference. 4. ASTM E 547, Test Method for Water Penetration of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential. 5. ASTM F 588, Standard Test Methods for Measuring the Forced Entry Resistance of Window Assemblies. D. Consumer Product Safety Commission (CPSC): 1. CPSC 16CFR-1201, Safety Standard for Architectural Glazing Materials. 1.03 SUBMITTALS A. Detail Drawings: Indicate dimensioning, direction of swing, frame and sash details, type of glazing material and handle height. B. Product Data: Manufacturer's literature including independently tested data listing performance criteria and Owner's Manual with installation instructions. C. Contract Closeout Submittal: Submit Owner's Manual from manufacturer. Identify with project name, location and completion date, type and size of unit installed. 1.04 QUALITY ASSURANCE A. Manufacturer: Provide complete, precision built, engineered, pre-fi tted unit by a single source manufacturer with at least 25 years experience in providing fenestration systems in the North American market. 1. The manufacturer must have a quality management system registration to the ISO 9001: 2008 standard. 2. The manufacturer must have an environmental management system registration to the ISO 14001: 2005 standard. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 27

NanaWall Matching Windows and Doors Guide Specifications B. Performance Requirements: Provide from manufacturer that has independently tested typical units per AAMA/ WDMA/CSA 101/I.S.2/A440-0 Testing results to include air infi ltration in accordance with ASTM E 283, water penetration in accordance with ASTM E 331 and ASTM E 547, structural loading in accordance with ASTM E 330 and forced entry in accordance with ASTM F 588. ** SPECIFIER NOTE: Structural load testing results are only applicable for the test unit size. (Comparative analysis charts published by manufacturer show which panel sizes (if any) would meet structural loading design pressures specifi cally required for the project. Check for limitations on the use of these charts in the jurisdiction of the project). See manufacturer's latest published data. C. Installer Qualifi cations: Installer experienced in the installation of manufacturer's products or other similar fenestration products. Installer to provide reference list of at least 3 projects of similar scale and complexity successfully completed in the last 3 years. Provide project names, locations, completion dates, names and telephone numbers of General Contractor and Owner's contact person. 1.05 WARRANTY A. Provide manufacturer's standard warranty against defects in materials and workmanship. B. Warranty Period: Ten years for seal failure of insulated glass supplied. For all other components, one year (two years if unit is installed by manufacturer's certifi ed trained installer) from date of delivery by manufacturer. 1.06 SITE CONDITIONS, DELIVERY, STORAGE AND HANDLING A. In addition to general delivery, storage and handling requirements specifi ed in Section 01600, comply with the following: 1. Deliver materials to job site in sealed, unopened cartons or crates. Protect units from damage. Store material under cover, protected from weather and construction activities. PART 2 PRODUCTS 2.01 SUPPLIER A. NANA WALL SYSTEMS, INC. - SL68 100 Meadow Creek Drive, Corte Madera, CA 94925 Toll Free: (800) 873-5673 Telephone: (415) 383-3148 Fax: (415) 383-0312 Website: www.nanawall.com Email: info@nanawall.com B. Other suppliers equal to the specified product must submit substitution request two weeks before bid for prior approval. 2.02 MATERIALS A. Frame and Sash: From manufacturer s standard profi les, provide frame, sash and glazing stops with dimensions shown on drawings. 1. Provide Sash with: Standard one lite [OR with horizontal mullion(s) at specifi ed height(s) from the bottom of the panel] [OR with simulated divided lites in pattern as shown on drawings]. 2. Aluminum Extrusion: Extrusions with nominal thickness of.078 (2.0 mm). Alloy specifi ed as AIMgSi0.5 with strength rated as 6063-T5 or F-22 (European standard). Anodized conforming to AAMA 611 or powder coated conforming to AAMA 2604 3. Thermally broken with ¾ -15/16 (20-24 mm) polyamide plastic reinforced with glass fi bers with additional insulating foam. 4. Aluminum Finish: Select from NanaWall Powder Coating Finish Chart 28 2013 NanaWall Systems www.nanawall.com SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE.

Guide Specifications NanaWall Matching Windows and Doors B. Glass: [OR dark bronze anodized] [OR clear anodized] [OR select from range of RAL high gloss powder coated fi nishes available from manufacturer] [OR select from range of RAL matte powder coated fi nishes available from manufacturer] [OR Wood Grain Finish] Same [OR different] fi nishes on inside and outside. [OR custom fi nish]. 1. Provide manufacturer s standard glass and dry glazing with EPDM gaskets and glass stops on the inside only. Glass to comply with safety glazing requirements of ANSI Z97.1 and CPSC 16CFR 120 15/16 (24 mm) insulating clear safety [OR 15/16 (24 mm) double glazed insulating argon fi lled Low-E safety] [OR 1 ½ (38 mm triple glazed insulating argon fi lled Low-E safety] [OR other glass available from manufacturer]. 2. For insulated units, provide manufacturer s standard glass spacers. Provide without capillary tubes [OR with capillary tubes]. C. Tilt Turn Hardware 1. Provide manufacturer s standard cam type multipoint locking mechanism. a. The concealed multipoint locking mechanism shall be driven by a single locking handle. 2. Provide manufacturer s standard hinges, hinges pins, strikes, and limit stays. 3. Handles: Stainless steel window handles in a titanium black fi nish [OR stainless steel window handles in a brushed satin fi nish] SPECIFIER S NOTE: Note that other compatible lever, handle styles and fi nishes are available from other suppliers. D. Provide handle height centered [OR at 41 3/8 from bottom of panel] [OR as specifi ed from bottom of panel]. E. Weather stripping: Provide manufacturer s standard double layer EPDM 2.03 FABRICATION A. Use extruded aluminum frame and panel profi les, corner connectors and hinges, tilt turn hardware and handles, glass and glazing and weather stripping as specifi ed herein to make a Dual Action Tilt Turn window. Factory pre-assemble as is standard for manufacturer and ship with all components and installation instructions. B. Sizes and Confi gurations: See drawings for dimensions, swing and number of single tilt turns, double sash tilt turns and double tilt turns with mullion. On double sash tilt turn, looking from inside, tilt turn panel on the left [OR right] 2.04 ACCESSORIES (Edit for project requirements.) A. Provide insect screen. Mesh in gray [Or black] Provide screen frame in aluminum: White powder coated [OR clear anodized] [OR dark bronze anodized] [OR powder coated select from range of RAL powder coated fi nishes available from manufacturer]. SPECIFICATIONS AND DETAILS SUBJECT TO CHANGE WITHOUT NOTICE 2013 NanaWall Systems www.nanawall.com 29