0 Most Widely Accepted and Trusted ICC ES Listing Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESL 1004 Reissued 03/2017 This listing is subject to renewal 03/2018. DIVISION: 13 00 00 SPECIAL CONSTRUCTION SECTION: 13 48 53 MANUFACTURED SEISMIC CONTROL COMPONENTS SECTION: 13 48 63 FABRICATED SEISMIC CONTROL ASSEMBLIES DIVISION: 21 00 00 FIRE SUPPRESSION SECTION: 21 05 48 VIBRATION AND SEISMIC CONTROLS FOR FIRE SUPPRESSION PIPING AND EQUIPMENT DIVISION: 22 00 00 PLUMBING SECTION: 22 05 48 VIBRATION AND SEISMIC CONTROLS FOR PLUMBING PIPING AND EQUIPMENT REPORT HOLDER: LOOS & CO., INC. 901 INDUSTRIAL BOULEVARD NAPLES, FLORIDA 34104 EVALUATION SUBJECT: SEISMIC WIRE ROPE/CABLE BRACING SYSTEM COMPONENTS (SEE TABLES 1 THROUGH 4) Look for the trusted marks of Conformity! 2014 Recipient of Prestigious Western States Seismic Policy Council (WSSPC) Award in Excellence A Subsidiary of ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this report, or as to any product covered by the report. Copyright 2017 ICC Evaluation Service, LLC. All rights reserved.
ICC-ES Listing Report ESL-1004 Reissued March 2017 Revised April 2017 This listing is subject to renewal March 2018. www.icc-es.org (800) 423-6587 (562) 699-0543 A Subsidiary of the International Council CSI: DIVISION: 13 00 00 SPECIAL CONSTRUCTION Section: 13 48 53 Manufactured Seismic Control Components Section: 13 48 63 Fabricated Seismic Control Assemblies Product Certification System: DIVISION: 21 00 00 FIRE SUPPRESSION Section: 21 05 48 Vibration and Seismic Controls for Fire-suppression Piping and Equipment DIVISION: 22 00 00 PLUMBING Section: 22 05 48 Vibration and Seismic Controls for Plumbing Piping and Equipment The ICC-ES product certification system includes evaluating reports of tests of standard manufactured product, prepared by accredited testing laboratories, and provided by the listee, to verify compliance with applicable codes and standards. The system also involves factory inspections, and assessment and surveillance of the listee s quality system. Products: Seismic Wire Rope/ Bracing System Components (see Tables 1 through 4) Listee: Evaluation: LOOS & CO., INC. 901 INDUSTRIAL BOULEVARD NAPLES, FLORIDA 34104 (800) 321-5667 www.loosseismicbracing.com The tension-only ( Type) Seismic Sway Brace Assemblies and components listed in Tables 5 through 14, when applied in accordance with the manufacturer s instructions, conform to the following standards: NFPA 13-10, Installation of Sprinkler Systems, National Fire Protection Association. ASCE/SEI 19-10, Structural Applications of Steel s for Buildings, American Society of Civil Engineers/Structural Engineering Institute. Findings: Seismic Wire Rope/ Bracing meets the requirements for tension-only bracing systems in Section 9.3.5.2 of NFPA 13, using the material requirements of ASCE/SEI 19-10, as referenced in the following sections of the applicable code edition: 2012 International Building (IBC) Applicable Sections: 903.3 and 2208.1 Identification: Installation: Each component of the Seismic Wire Rope/ Bracing is identified with a label indicating the manufacturer s name and address, the product name, the part number of the component, the ICC-ES Listing Report Number (ESL-1004), and when applicable, the ICC-ES Listing Mark. The system must be installed in accordance with the Loos and Company, Inc., installation instructions. Listings are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed as an endorsement of the subject of the listing or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this listing, or as to any product covered by the listing. Copyright 2017 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 6
ESL-1004 Most Widely Accepted and Trusted Page 2 of 6 Conditions of Listing: 1. This listing report addresses only those findings noted above. 2. Approval of the products use is the sole responsibility of the local code official. 3. This listing report applies only to the materials tested and as submitted for review by ICC-ES. 4. Use the load combinations of ASCE/SEI 19, as modified by Section 2208.2 of the 2012 IBC. The breaking strength must be higher than 1.5xT 3 and 1.5xT 4. 5. Steel cables must be color-coded, as indicated in Tables 5 through 14, for field identification. 6. All components of the cable assembly must be able to develop the minimum breaking strength of the steel cables as required in ASTM A1023, Table 9. TABLE 1 STRUCTURAL ATTACHMENT FITTING SERIES FITTING Structural Attachment Fitting (SAF) Structural Attachment Fitting Retrofit (SAFR) Structural Attachment Fitting 2 Way (SAF2) Structural Attachment Fitting 2 Way Retrofit (SAF2-R) SIZE SAF-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8 SAF-1, SAF-1 1/4 SAFR-1/4, SAFR-3/8, SAFR-1/2, SAFR-5/8 SAF2-1/4, SAF2-3/8, SAF2-1/2,SAF2-5/8, SAF2-3/4, SAF2-7/8 SAF2-1/4R, SAF2-3/8R, SAF2-1/2R, SAF2-5/8R STRUCTURAL ATTACHMENT FITTING (SAF) STRUCTURAL ATTACHMENT FITTING RETROFIT (SAFR) STRUCTURAL ATTACHMENT FITTING 2 WAY (SAF2) STRUCTURAL ATTACHMENT FITTING 2 WAY RETROFIT (SAF2R)
ESL-1004 Most Widely Accepted and Trusted Page 3 of 6 TABLE 2 OVAL SLEEVES Component Number SL2-3P SL2-4P SL2-6P SL2-8P For SI 1inch = 25.4 mm Reference 3 / 32 1 / 8 3 / 16 1 / 4 OVAL SLEEVE TABLE 3 LOW PRY FITTINGS Component Number Hole (inch) LPF-1/4 0.260 LPF-3/8 0.415 LPF-1/2 0.525 LPF-5/8 0.660 LPF-3/4 0.798 For SI 1inch = 25.4 mm LOW PRY FITTING (LPF) TABLE 4 STAKE EYE AND CABLE ASSEMBLIES Stake-Eye Part Number Configuration EY8-251-3P 1 EY8-376-3P 2 EY8-260-4P 1 EY8-376-4P 2 EY8-501-4P 2 EY8-505-6P 2 EY8-375-6P 2 EY8-625-8P 2
ESL-1004 Most Widely Accepted and Trusted Page 4 of 6 TABLE 5 STRUCTURAL ATTACHMENT FITTING (SAF) AND CABLE ASSEMBLY Color Nominal 3 / 16 7x19 End Fittings SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, AND SAF-1-1/4; and Oval SAF-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF-1-1/4; and Oval SAF-1/4, SAF-3/8, SAF-1/2, SAF-5/8, SAF-3/4, SAF-7/8, SAF-1, and SAF-1-1/4; and Oval 4200 Color TABLE 6 STRUCTURAL ATTACHMENT FITTING 2 (SAF2) AND CABLE ASSEMBLY Nominal End Fittings 3 / 16 7x19 SAF2-5/8, SAF2-3/4, and SAF2-7/8; and Oval 4200 SAF2-1/4, SAF2-3/8, SA2F-1/2, SAF2-5/8, SAF2-3/4,and SAF2-7/8; and Oval SAF2-1/4, SAF2-3/8, SAF2-1/2, SAF2-5/8, SAF2-3/4,and SAF2-7/8; and Oval Color TABLE 7 STRUCTURAL ATTACHMENT FITTING RETROFIT (SAFR) AND CABLE ASSEMBLY Nominal End Fittings SAFR-1/4, SAFR-3/8, SAFR-1/2, and SAFR-5/8; and Oval SAFR-1/4, SAFR-3/8, SAFR-1/2, and SAFR-5/8; and Oval TABLE 8 STRUCTURAL ATTACHMENT FITTING RETROFIT 2 (SAF2-R) AND CABLE ASSEMBLY Color Nominal End Fittings SAF2-1/4R, SAF2-3/8R, SAF2-1/2R, and SAF2-5/8R; and Oval SAF2-1/4R, SAF2-3/8R, SAF2-1/2R, and SAF2-5/8R; and Oval
ESL-1004 Most Widely Accepted and Trusted Page 5 of 6 TABLE 9 LOW PRY FITTING (LPF) AND CABLE ASSEMBLY (Fitting Mounting 0º to 90º from Line of Tension) Color Nominal End Fittings LPF-1/4, LPF-3/8, LPF-1/2, LPF-5/8, and LPF-3/4; and Oval LPF-1/4, LPF-3/8, LPF-1/2, LPF-5/8, and LPF-3/4; and Oval Color Nominal TABLE 10 BENT (45º) STAKE EYE AND CABLE ASSEMBLY WITH STAKE EYE (Mounted 0º to 90º from Line of Tension) End Fittings EY8-260-4P EY8-251-3P, EY8-376-3P Color Nominal TABLE 11 BENT (45º) STAKE EYE AND CABLE ASSEMBLY WITH STAKE EYE (Mounted 0º to 60º from Line of Tension) End Fittings 3 / 16 7x19 EY8-375-6P, EY8-505-6P 4200 EY8-260-4P, EY8-376-4P, EY8-501-4P EY8-251-3P, EY8-376-3P Color Black TABLE 12 STRAIGHT STAKE EYE AND CABLE ASSEMBLIES WITH STAKE EYE (Mounted In Line with Tension - 0º angle) Nominal End Fittings 1 / 4 7x19 EY8-625-8P 7000 3 / 16 7x19 EY8-375-6P, EY8-505-6P 4200 EY8-260-4P, EY8-376-4P, EY8-501-4P EY8-251-3P, EY8-376-3P Color Black Nominal TABLE 13 CABLE LOOP ON BAR JOIST (In Line with Tension - 0º angle) End Fittings 1 / 4 7x19 Loop with Oval 7000 3 / 16 7x19 Loop with Oval 4200 Loop with Oval Loop with Oval
ESL-1004 Most Widely Accepted and Trusted Page 6 of 6 BAR JOIST LOOP Color Nominal TABLE 14 CABLE SPLICE WITH OVAL SLEEVES (in Line with Tension [0º angle]) End Fittings Black 1 / 4 7x19 SL2-8P Oval s 1 7000 3 / 16 7x19 SL2-6P Oval s 1 4200 SL2-4P Oval s 1 SL2-3P Oval s 1 Notes: 1 Two Oval s are required. CABLE SPLICE