STATE OF NEW HAMPSHIRE DEPARTMENT OF NATURAL AND CULTURAL RESOURCES DIVISION OF PARKS AND RECREATION PROJECT #: CAP 1804 FRANCONIA NOTCH STATE PARK FRANCONIA, NEW HAMPSHIRE BID SET 8/4/2017 DRAWING LIST: COVER SHEET & NOTES ARCHITECTURAL A0.01 LEGEND, ABBREVIATIONS AND SCHEDULES A1.01 FLOOR, ROOF AND FRAMING PLANS A2.01 EXTERIOR ELEVATIONS A3.01 SECTIONS A3.02 SECTIONS A4.01 FRAMING DETAILS A4.02 DETAILS NOTES: 1 - WORK SHALL BE PERFORMED ACCORDING TO ALL APPLICABLE FEDERAL, STATE AND LOCAL BUILDING CODES FOR HIGH WIND REQUIREMENTS. 2 - ALL CONTRACTORS AND SUB-CONTRACTORS SHALL FAMILIARIZE THEMSELVES WITH THE CONSTRUCTION DOCUMENTS AND ANY EXISTING CONDITIONS. THIS IS TO PROVIDE AN OPPORTUNITY TO CLARIFY ANY QUESTIONS PRIOR TO THE START OF CONSTRUCTION. 3 - THE GENERAL CONTRACTOR SHALL COORDINATE WITH THE OWNER ACCESS TO THE SITE, AND ANY SPECIFIC OWNER REQUIREMENTS AND PROCEDURES FOR ACCESSING THE SITE. 4 - ALL DIMENSIONS ARE TO THE FACE OF MASONRY OR FACE OF STUD, UNLESS NOTED OTHERWISE. 5 - ALL ANGLES SHOWN ON THE PLANS ARE 45, UNLESS NOTED OTHERWISE. 6 - THE GENERAL CONTRACTOR SHALL BE FULLY RESPONSIBLE FOR VERIFYING ALL DIMENSIONS. ANY DISCREPANCY BETWEEN ANTICIPATED AND ACTUAL CONDITIONS SHALL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT PRIOR TO PROCEEDING WITH THE WORK.
INTERIOR ELEVATION DOOR SCHEDULE EXTERIOR ELEVATION BUILDING SECTION WINDOW SCHEDULE WALL SECTION DETAILS WINDOW & FRAME TYPE DOOR NUMBER ACCESSORY TYPE REVISION NUMBER INDICATES BARRIER FREE ACCESS. ITEMS DESIGNATED MUST COMPLY WITH LATEST LOCAL CODE EDITIONS AND FEDERAL ACCESSIBILITY LEGISLATION SYMBOLS LEGEND THERMAL OR ACOUSTIC FIBERGLASS INSULATION CMU PARTITION CONCRETE STEEL RIGID INSULATION LOAM GRAVEL SPRAYED-ON FIREPROOFING WOOD BLOCKING FINISH WOOD GRAPHICS LEGEND Room Name & Number DATUM/WORK POINT INDICATES ALIGNMENT ROOM TAG PARTITION TYPE DEMOLITION NOTE NEW WALL EXISTING WALL TO REMAIN EXISTING WALL TO BE REMOVED NEW DOOR & FRAME EXISTING DOOR & FRAME COLUMN GRID INDICATOR ABBREVIATIONS WALL TYPES & SCHEDULES TYPE A TYPE B DOOR TYPES TYPE 1 - HOLLOW METAL FRAME TYPES Department of Natural and Cultural resources LEGEND, ABBREVIATIONS AND SCHEDULES FRONT APPROACH, PULL SIDE HINGE APPROACH, PULL SIDE LATCH APPROACH, PULL SIDE LATCH APPROACH, PUSH SIDE FRONT APPROACH, PUSH SIDE HINGE APPROACH, PUSH SIDE LATCH APPROACH, PULL SIDE W/CLOSER LATCH APPROACH, PUSH SIDE W/CLOSER DOOR CLEARANCES A0.01
TOILET RM TUNING ROOM DISPATCH DAY ROOM ENTRY PORCH TOBOGAN STG VESTIBULE MARK SHEATHING TYPE (APA RATED) TYPICAL SHEAR WALL SCHEDULE MINIMUM NAIL PENETRATION NAIL SIZE (a) EDGE NAIL SPACING (@ ALL PLYWD EDGES) FIELD NAIL SPACING SILL PLATE TO CONC ANCHOR TO WOOD TYPE: 15/32" PLYWOOD 1 1/2" 8d 4" 6" - 16d @ 4" (a) (b) FASTENERS SHALL BE COMMON WIRE OR GALVANIZED BOX AT PLYWOOD SHEAR WALLS. SIMPSONS "WSNTL" WOOD SCREWS MAY BE USED IN LIEU OF NAILS BY APPROVAL OF ARCHITECT. ALL EDGES ARE BLOCKED AND EDGE NAILING IS PROVIDED AT ALL SUPPORTS AND PANEL EDGES. FLOOR, ROOF AND FRAMING PLANS FRAMING NOTES: A1.01
A2.01 EXTERIOR ELEVATIONS Department of Natural and Cultural resources
A3.01 SECTIONS
A3.02 SECTIONS
A4.01 FRAMING DETAILS
A4.02 DETAILS