STRENGTH PERFORMANCE OF CONCRETE USING BOTTOM ASH AS FINE AGGREGATE

Similar documents
Behaviour of Self Compacting Concrete by Partial Replacement of Fine Aggregate with Coal Bottom Ash

Performance of High Strength Concrete Prepared by Partially Replacing Fine Aggregate with Bottom Ash

Strength properties of concrete with partial replacement of sand by bottom ash

An Experimental Study on Flexural behaviour of Reinforced Concrete Beam by Partial Replacement of Fine aggregate with Coal based Brick- Kiln-Ash

International Journal of Scientific & Engineering Research, Volume 7, Issue 10, October ISSN

Study On Properties Of High Strength Silica Fume Concrete Withpolypropylene Fibre

Study of High Performance Concrete with Silica Fume and Glass Fibre

Mechanical properties of high strength mortar for repair works

Influence of Silica Fume & Recycled Concrete Aggregates on Mechanical Properties of Concrete

EFFECT ON CONCRETE PROPERTIES BY REPLACEMENT OF SAND AS THERMAL POWER PLANT POND ASH

A Study on the Influence of Mineral Admixtures in Cementitious System Containing Chemical Admixtures

Effect of cement and fine aggregate replacement with Alccofine and Bottom ash on mechanical properties of concrete

Experimental Study on Partial Replacement of cement by Fly Ash with Glass Fiber Reinforcement

EXPERIMENTAL INVESTIGATION ON PARTIAL REPLACEMENT OF FINE AGGREGATE WITH SABBATH (CUDDAPAH STONE) STONE

EFFECT OF COAL BOTTOM ASH AS SAND REPLACEMENT ON THE PROPERTIES OF CONCRETE WITH DIFFERENT W/C RATIO

Study on Effect of Steel Dust on Strength Characteristics of Concrete

International Journal of Scientific & Engineering Research, Volume 7, Issue 10, October ISSN

EXPERIMENTAL INVESTIGATION ON MECHANICAL PROPERTIES OF POLYPROPYLENE FIBRE INCORPORATED CONCRETE WITH SILICA FUME

Experimental Study on Glass Fibre Reinforced Steel Slag Concrete with Fly Ash

An Experimental Study on Partial Replacement of Cement by Ggbs and Natural Sand by Quarry Sand in Concrete

Strength Properties of Metakaolin Admixed Concrete

Experimental Investigation on The Effect Of M-Sand In High Performance Concrete

Replacement of Fine Aggregate in Concrete with Municipal Solid Waste Bottom Ash from Incinerator

EXPERIMENTAL INVESTIGATION OF WASTE FOUNDRY SAND ON STRENGTH PROPERTIES OF PLAIN CONCRETE AND COMPARISON WITH BINARY BLENDED CONCRETE

The Influence of Metakaolin on the Modulus of Elasticity of Concrete

STUDY ON SILICA FUME REPLACED CONCRETE WITH SUPER PLASTICIZER

EFFECT ON MECHANICAL PROPERTIES OF CONCRETE USING NYLON FIBERS

International Journal of Engineering Science Invention Research & Development; Vol. I Issue XI May e-issn:

Effect of Calcium Nitrate on the Pozzolanic Properties of High Early Strength Concrete

Laboratory Analysis of Fly Ash Mix Cement Concrete for Rigid Pavement.

Study and Analysis of High Performance Concrete and Estimation of Concrete Strength

Research Article The Effect of Accelerators and Mix Constituents on the High Early Strength Concrete Properties

Impact of Fly Ash and Silpozz as Alternative Cementitious Material in Crusher Dust Concrete [1]

An Investigation of Steel Fiber Reinforced Concrete with Fly Ash

STRENGTH AND DURABILITY PROPERTIES OF HIGH PERFORMANCE CONCRETE INCORPORATING SILICA FUME

Effect of Steam Curing on the Strength of Concrete by Using Mineral Admixtures

Study on Partial Replacement of Fine Aggregate by Quarry Rock Flyash

STUDY ON MECHANICAL PROPERTIES OF CONCRETE USING SILICA FUME AND QUARTZ SAND AS REPLACEMENTS

JOURNAL OF INTERNATIONAL ACADEMIC RESEARCH FOR MULTIDISCIPLINARY Impact Factor 1.393, ISSN: , Volume 2, Issue 2, March 2014

Comparative Study on the Effect of Concrete using Eco Sand, Weathered Crystalline Rock Sand and GBS as fine Aggregate Replacement

AN EXPERIMENTAL INVESTIGATION OF PARTIAL REPLACEMENT OF CEMENT USING MICRO SILICA AND FLY ASH IN PRODUCTION OF COCONUT SHELL CONCRETE

Study on Strength Characteristics of High Strength Rice Husk Ash Concrete

Study of Mechanical and Durability Properties of High Performance Self Compacting Concrete with Varying Proportion of Alccofine and Fly Ash

A Study on Strength of Concrete by Partial Replacement of Cement with Metakaolin and Fine Aggregate with Stone Dust

Keywords - Recycled Coarse Aggregate (RCA), Compressive Strength, C&D Construction and Demolition Waste

STRENGTH PARAMETERS OF CONCRETE CONTAINING RECYCLED AGGREGATE

Index Terms- Copper Slag (CS), Silica Fume (SF), Physical Properties, Compressive Strength, Flexural Strength.

AN EXPERIMENTAL STUDY ON HIGH PERFORMANCE CONCRETE PARTIALLY REPLACING CEMENT AND FINE AGGREGATE WITH GGBS & ROBO SAND

Strength and durability of high performance engineered cementitious composites

Effect of Different Types of Coarse Aggregates on Physical Properties of Mostly Used Grades M20, M25, M30 of Concrete

Analysis on Mix Design of High Strength Concrete (M100)

EFFECT OF THE LIME CONTENT IN MARBLE POWDER FOR PRODUCING HIGH STRENGTH CONCRETE

STRENGTH CHARACTERISTICS OF CONCRETE WITH WASHED BOTTOM ASH PARTIALLY REPLACED FOR FINE AGGREGATE

Experimental Study on Rice Husk Ash in Concrete by Partial Replacement

EXPERIMENTAL STUDY ON ECOFRIENDLY POLYPROPYLENE FIBRE REINFORCED CONCRETE USING FOUNDRY SAND

Effect of silica fume on the resistance to chloride ion penetration in high performance concrete

Properties of Concrete Incorporating Recycled Post-Consumer Environmental Wastes

An Experimental Study On Strength & Durability Of Concrete Using Partial Replacement Of Cement With Nano Silica

EFFECT OF SILICA FUME ON VARIOUS PROPERTIES OF FIBRE REINFORCED CONCRETE

Experimental Study on Partial Replacement of Cement by Hyposludge in Concrete

Effect of Micro Silica on the properties of hardened concrete

Behaviour of Glass Fibre Reinforced Concrete Using Ultra Fine Micro silica and Copper Slag IJETED

Effect of Fly Ash and Silica Fumes on Strength, Stress Strain Behaviour of M 25 Concrete Mix

Anil Kumar Nanda, Jaspal Singh. Evaluation of Relation between Split Tensile and Compressive Strength of OPC Concrete

EXPERIMENTAL STUDY OF EFFECTS OF POTASSIUM CARBONATE ON STRENGTH PARAMETERS OF CONCRETE. 3 Mehvish, Insha Bashir. J&K, India

India, Keywords- fly ash, silica fume, compressive strength, tensile strength. (C)Global Journal Of Engineering Science And Researches

Evaluation of High Performance Concrete by Partial Replacement of Cement with Silica Fume Natural Sand and Manufactured Sand

2 LITERATURE REVIEW IJSER

Fibrous Triple Blended Concrete Composites Study of Strength Properties

Effectiveness of Use of Rice Husk Ash as Partial Replacement of Cement in Concrete

EXPERIMENTAL STUDIES ON EFFECTIVE WAY OF UTILIZING SUGARCANE BAGASSE ASH AS SUPPLEMENTARY CEMENTITIOUS MATERIAL IN CONCRETE

Experimental Study on Slurry Infiltrated Fibre Reinforced Concrete with Partial Replacement of Fly Ash

Experimental Study on Properties and Effects of Copper Slag in Self Compacting Concrete

EFFECT OF STEEL SLAG AND FLY ASH ON THE PROPERTIES OF CONCRETE MIX FOR PAVEMENT

LECTURE NO. 10 & 11 (Part II) MINERAL ADMIXTURES

A. HIGH-STRENGTH CONCRETE (HSC)

Study on Effect of Self-Compacting Concrete with Partial Replacement of Mineral Admixtures Using Quarry Dust

THE EFFECT OF STEEL FIBERS ON THE MECHANICAL PROPERTIES OF HIGH PERFORMANCE CONCRETE

International Journal of Advance Engineering and Research Development

EFFECT OF PARTIAL REPLACEMENT OF CEMENT BY SILICA FUMES ON MECHANICAL PROPERTIES OF CONCRETE

CHAPTER 6 POLYPROPYLENE FIBRE REINFORCED GEOPOLYMER CONCRETE COMPOSITES

CONTROLLING ENVIRONMENTAL POLLUTION THROUGH CONCRETE TECHNOLOGY

International Journal of Innovative Research in Advanced Engineering (IJIRAE) ISSN:

Study on Strength Properties of Concrete by Partially Replacing Fine Aggregate as Steel Slag

Effect of Mixing Fibers on Flexural Strength of Concrete Mix

Experimental Study on Development of Normal Strength Concrete and High Strength Concrete Using Alccofine

Experimental Investigation on Self Compacting Concrete by Partial Replacement of Fine Aggregate with Quarry Dust and Cement with Fly Ash

Strength Properties of High Grade Concrete Replacing Main Ingredients by Quarry Dust & Silica fume

STRENGTH AND RHEOLOGICAL PROPERTIES OF FIBER REINFORCED SELF COMPACTING CONCRETE WITH ALCCOFINE

YIELD OF CONCRETE WITH MINERAL ADMIXTURE

Particle Size Effect of Ground Granulated Blast Furnace Slag (GGBS) in Cement Concrete

USE OF FLY ASH, RICE HUSK ASH AND QUARRY DUST FOR MAKING GREEN CONCRETE

Performance of High Strength High Performance Steel Fiber Reinforced Concrete for use in Seismic Resistant Structures

NATURAL POLYMER AS WATERPROOFING COMPOUND IN CEMENT CONCRETE

Study of Properties of Self Compacting Concrete with Micro Steel Fibers and Alccofine

Experimental Study On Hybrid Fibre Concrete With Using GGBS And M Sand

Properties of Concrete Containing Recycled Fine Aggregate and fly ash

COMPARATIVE STUDY OF USE OF SILICA FUME AND FLY ASH ON PROPERTIES OF CONCRETE

Physical Properties of Steel Fiber Reinforced Cement Composites Made with Fly Ash

A STUDIES ON BEHAVIOUR OF GEOPOLYMER CONCRETE

Transcription:

IMPACT: International Journal of Research in Engineering & Technology (IMPACT: IJRET) ISSN(E): 2321-8843; ISSN(P): 2347-4599 Vol. 2, Issue 9, Sep 14, 111-122 Impact Journals STRENGTH PERFORMANCE OF CONCRETE USING BOTTOM ASH AS FINE AGGREGATE REMYA RAJU 1, MATHEWS M. PAUL 2 & K. A. ABOOBACKER 3 1 Post Graduate Student, Department of Civil Engineering, Mar Athansius College of Engineering, Kothamangalam, Kerala, India 2 Professor, Department of Civil Engineering, Mar Athansius College of Engineering, Kothamangalam, Kerala, India 3 Consultant, Structural Engineer, Structural and Foundation Engineer, Kochi, Kerala, India ABSTRACT Concrete is the most important engineering material and the addition of some other materials may change the properties of concrete. Studies have been carried out to investigate the possibility of utilizing a broad range of materials as partial replacement materials for cement and aggregate in the production of concrete. The present experimental study was conceived following the general purpose of testing new sustainable building processes and modern production systems, aims not only at saving natural raw materials and reducing energy consumption, but also to recycle industrial by-products. The objectives of this study was to investigate the effect of use of coal bottom ash as partial replacement of fine aggregates in various percentages ( 3%), on concrete properties such as compressive strength, spiltting tensile strength test, flexural strength and modulus of elasticity and also the effect of microsilica in bottom ash concrete having maximum compressive strength. The test results of this research work indicates that at fixed water cement ratio, workability decreased with the use of coal bottom ash as a replacement of fine aggregate in concrete. Compressive strength of bottom ash concrete at the curing age of 28 days was increased compared to control concrete. Splitting tensile strength of concrete improved at percentages of replacement of bottom ash. The modulus of elasticity decreased with the use of coal bottom ash at all replacement levels. KEYWORDS: Coal Bottom Ash, Concrete, Compressive Strength, Splitting Tensile Strength, Flexural Strength, Modulus of Elasticity INTRODUCTION Concrete is the most vital material for the construction of high rise buildings and various infrastructures. Infrastructure development in such areas particularly in developing countries like India is more. Concrete is a mixture of cement, fine aggregate, coarse aggregate and water and river sand is the main raw material used as fine aggregate in the production of concrete. The natural sources of river sand are getting depleted gradually. The demand for the protection of the natural environment and the ban on mining in some areas is further aggravating the problem of availability of river sand. At present, the construction industry is plagued with the scarcity of this essential constituent material of concrete. Therefore, in the present circumstances of scant sources of river sand and boom in infrastructure development, it becomes essential and more significant to find out its substitute material in concrete. Impact Factor(JCC): 1.5548 - This article can be downloaded from www.impactjournals.us

112 Remya Raju, Mathews M Paul & K. A. Aboobacker Coal bottom ash is a coarse granular and incombustible byproduct from coal burning furnaces. It is composed of mainly silica, alumina and iron with small amounts of calcium, magnesium sulfate, etc. The appearance and particle size distribution of coal bottom ash is similar to that of river sand. These properties of coal bottom ash make it attractive to be used as fine aggregate in the production of concrete. Singh and Siddique [1] also reported that coal bottom ash is the potentially viable material to be used as fine aggregate in the production of concrete. The previous studies in which coal bottom ash has been targeted as a substitute for sand in production of concrete demonstrate that the strength development pattern of coal bottom ash concrete is similar to that of conventional concrete. Aggarwal et al. [4] reported that the workability in terms of compaction factor, compressive strength and splitting tensile strength decreased on use of pond ash as replacement of sand in concrete. A research was conducted by Abdulhameed et al. [5] on properties of concrete using tanjung bin power plant coal bottom ash and fly ash. Coal bottom ash and fly ash were utilized in partial replacement for fine aggregates and cement respectively in the range of, 5, 1, 15 & % (equal percentages). Their results showed that for a grade M35 concrete with a combination of coal bottom ash and fly ash can produce 28 day strength above 3MPa. They concluded that the use of coal bottom ash and fly ash in concrete has the potential to produce long term durable and good strength concrete. M. P. Kadam and Dr. Y. D. Patil [6] were studied the effect of coal, bottom ash as sand replacement on the properties of concrete with different w/c ratio. They concluded that upto 3% replacement of bottom ash, the compressive strength, split tensile strength and flexural strength increased for all 7, 1 14, 28, 56 and 9 days of curing. A study was conducted by P. Tang et al. [7], on the application of Municipal Solid Waste Incineration (MSWI) bottom ash fines in high performance concrete they concluded that the concrete porosity increases with increase of bottom ash fines. The compressive and flexural strength of concrete decrease with the increase of the bottom ash fines at the same curing age, especially after 3 and 7 days. Yogesh Aggarwal and Rafat Siddique [8], were studied microstructure and properties of concrete using bottom ash and waste foundry sand as partial replacement of fine aggregates. They concluded that the mechanical behavior of the concrete with fine aggregate replacements was comparable to that of conventional concrete except for 6% replacement. The inclusion of waste foundry sand and bottom ash as fine aggregate does not affect the strength properties negatively as the strength remains within limits except for 6% replacement. A study was carried out in 13 by PG scholar C Mathiraja [9], on concrete using bottom ash, manufacturing sand and hybrid steel and coir fibers. The inclusion of fibers into concrete not only provides considerably more ductile structure but also improves such structural properties as tensile strength, static flexural strength, impact strength, flexural toughness and the energy absorption capacity of the high strength concrete. The research work carried out by Kim and Lee [1] indicates that the compressive strength of concrete mixtures made with coal bottom ash as a substitute for sand was not strongly affected. However, flexural strength and modulus of elasticity of concrete decreased with the increase in the content of coal bottom ash. The value of the current research is the use of coal bottom ash as fine aggregate. The mineral admixture used in this study was microsilica, which is extracted from exhaust gases of silicon and ferrosilicon smelting furnaces and utilized in concrete to improve the properties of the concrete. The main purpose of incorporating the material in concrete is to make use of the very fine and reactive particles to produce a denser cement matrix. The microsilica particles have a pozzolanic reaction with calcium hydroxide from the hydration of the cement, thereby increasing the total product of hydration and Index Copernicus Value: 3. - Articles can be sent to editor@impactjournals.us

Strength Performance of Concrete Using Bottom Ash as Fine Aggregate 113 reducing the amount of calcium hydroxide. When properly used, microsilica decreases the permeability of the concrete providing a more durable and more sustainable product. A small quantity of microsilica can be effective in a concrete mix, a typical dosage being in the range 5 to 1% by weight of the cement. The objectives of this study are to investigate the effect of use of bottom ash as partial replacement of fine aggregates in various percentages ( 3%), on concrete properties such as compressive strength, workability, flexural strength etc. and also the determine the optimum dosage of microsilica in bottom ash concrete having maximum compressive strength. The present experimental study was conceived following the general purpose of testing new sustainable building processes and modern production systems, aims not only at saving natural raw materials and reducing energy consumption, but also to recycle industrial by-products. Utilization of coal combustion products in construction industry is an important issue involving reduction in technical and economical problems of plants, besides reducing the amount of solid wastes, greenhouse gas emissions and conserving existing natural resources. MATERIALS AND METHODS Materials Ordinary Portland Cement (53 MPa) conforming to relevant Indian standard specifications [11] with consistency as 35% and specific gravity as 3.15 was used. M sand with 4.75 mm maximum size was used as fine aggregate, fulfilling the requirements of IS:383-197 [13] along with crushed stone of mm maximum size used as coarse aggregate. The particle size distribution fine aggregate was shown in Figure 1. The physical properties of fine aggregate and coarse aggregate was tabulated in Tables 1 and 2 respectively. Coal bottom ash obtained from Hindustan Newsprint Limited, Kottayyam, Kerala, India was used as partial replacement of fine aggregates. The coal bottom ash was screened to remove the oversized particles and the material passing through 4.75 mm sieve was used in manufacturing of concrete. The chemical and physical properties of coal bottom ash used in this research are given in Tables 3 and 4 respectively. The chemical analysis shows that coal bottom ash is mainly composed of silica and alumina. The particle size distribution of bottom ash used in this investigation was shown in Figure 2. Microsilica for the present investigation was supplied by BSS Pvt. Ltd at Cochin, Kerala. The superplasticizer used in this present investigation was Master Rheobuild 1125 manufactured by BASF Chemicals Pvt. Ltd. Table 1: Physical Properties of Fine Aggregate Sl. No. Properties Value 1 Specific gravity 2.66 2 Water absorption 12 %. 3 Fineness modulus 3.12 4 Grading Zone Zone II 1 9 LOWER LIMIT UPPER LIMIT PERCENTAGE PASSING 8 P E R C E N T A G E F IN E R (% ) 7 6 5 3 1.1 1 1 1 PARTICLE SIZE(mm) Figure 1: Grading Curve of Fine Aggregate Impact Factor(JCC): 1.5548 - This article can be downloaded from www.impactjournals.us

114 Remya Raju, Mathews M Paul & K. A. Aboobacker Table 2: Physical Properties of Coarse Aggregate Properties Values Specific gravity 2.72 Water absorption for mm aggregate 1.3 % Water absorption for 12.5 mm aggregate 1.94 % Table 3: Physical Properties of Bottom Ash Sl. No. Properties Value 1 Specific gravity 2.2 2 Water absorption 17 %. 3 Fineness modulus 2.85 Table 4: Chemical Composition of Bottom Ash SL No Element Mass% 1 C 15.4 2 O 6.27 3 Al 9.2 4 Si 12.62 5 K.64 6 Ti.71 7 Fe 1.69 1 8 6 % finer 1 1 1 1 seive opening Figure 2: Particle Size Distribution Curve of Bottom Ash Experimental Program Ordinary Portland Cement of 53 grade conforming to relevant Indian Standard specifications [11] has been used for making the concrete mixtures. Seven mix proportions were prepared. First was control mix (without bottom ash), and the other six mixes contained bottom ash. Fine aggregate (M sand) was replaced with bottom ash by weight with a replacement range from 5% to 3% at the increment of 5%. The control mix without bottom ash was proportioned as per Indian Standard specifications [16], to obtain a 28-day cube compressive strength of 35MPa. In the first stage fresh and hardened properties of bottom ash concrete was studied and an optimum mix was found out. In the second stage, considering that optimum mix as control mix, six other mixes were prepared by adding microsilica in varying percentages (4%, 6%, 8%, 1%, 12% & 15%.) by replacing cement. For these mix proportions, quantities of materials used are shown in Table 5 and Table 6. Fresh concrete properties such as slump flow, was determined according to an Indian Standard specifications [15]. Index Copernicus Value: 3. - Articles can be sent to editor@impactjournals.us

Strength Performance of Concrete Using Bottom Ash as Fine Aggregate 115 The concrete cubes of 15 mm x15mm x 15mm, cylinders of size 15 mm diameter 3 mm height and beams of size 15 mm x 15 mm x 7 mm were prepared. After required period of curing, the specimens were taken out of the curing tank and their surfaces were wiped off. The various tests performed were compressive strength test of cubes at 7 th and 28 th days, splitting tensile strength of cylinders at 28 days, water absorption and flexural strength of beams at 28days and modulus of elasticity as per relevant Indian Standard specifications [14]. Mixture Mixture W/C Ratio Table 5: Trial Mix Details of Mix 1 Cement Sand Bottom Ash Coarse Aggregate Water Control mix.4 345 629.85 1222.65 138 BAC 5.4 345 598.35 31.5 1222.65 138 BAC 1.4 345 566.85 63. 1222.65 138 BAC 15.4 345 535.35 94.5 1222.65 138 BAC.4 345 53.35 126. 1222.65 138 BAC 25.4 345 472.35 157.5 1222.65 138 BAC 3.4 345 4.85 189. 1222.65 138 W/C Ratio Table 6: Trial Mix Details of Mix II Cement Microsilica Sand Bottom Ash Coarse Aggregate Water Control Mix.4 345. 566.85 63 1222.65 138 BM 4.4 331. 13.8 566.85 63 1222.65 138 BM 6.4 324.3.7 566.85 63 1222.65 138 BM 8.4 317. 27.6 566.85 63 1222.65 138 BM 1.4 31.5 34.5 566.85 63 1222.65 138 BM 12.4 293.3 41. 566.85 63 1222.65 138 BM 15.4 276. 51.8 566.85 63 1222.65 138 RESULTS AND DISCUSSIONS Properties of Fresh Concrete Slump Test Figures 3 and 4. The workability of concrete is measured by performing slump test. The test results are presented in 1 11 variation of slump for various percentages of bottom ash 1 9 slump obtained in mm 8 7 6 5 3 1 5 1 15 25 3 percentage of bottom ash Figure 3: Slump Obtained for Bottom Ash Concrete The test results show that slump values of bottom ash concrete mixtures decreased with the increase in level of fine aggregate replacement by bottom ash. The similar trend was observed in bottom ash concrete with microsilica. Impact Factor(JCC): 1.5548 - This article can be downloaded from www.impactjournals.us

116 Remya Raju, Mathews M Paul & K. A. Aboobacker The water absorption of bottom ash is higher than that of sand particles. The rough texture and complicated shape of particles of bottom ash also played significant role in increasing the inter particle friction. The above factors contributed towards lowering the slump. When micro silica was added to bottom ash concrete workability again decreases. This reduction is due to the higher percentage of finer particles than 15 microns. 1 variation of slump 8 slump obtained in mm 6-2 2 4 6 8 1 12 14 16 percentage of microsilica Figure 4: Slump Obtained for Bottom Ash Concrete with Microsilica PROPERTIES OF HARDENED CONCRETE Compressive Strength Test Compressive strength 6 55 5 45 35 3 25 15 1 5 5 1 15 25 3 35 percentage replacement of bottom ash 7 th day compressive strength 28 th day compressive strength Figure 5: Variation of Compressive Strength of Bottom Ash Concrete on 7 and 28 Day Curing The 7 th and 28 th day cube compressive strength of bottom ash concrete are shown in Figure 5. The results of 28 th day cube compressive strength of bottom ash concrete with microsilica was shown in Figure 6. 6 28 th day compressive strength compressive strength 55 5 45 35 3 25 15 1 5 2 4 6 8 1 12 14 16 18 percentage of microsilica Figure 6: Effect of Microsilica in Optimum Bottom Ash Concrete The results show that the strength development patterns of bottom ash concrete at all the levels of fine aggregate replacement with bottom ash is similar to that of control concrete. At the curing age of 7 days, concrete mixtures Index Copernicus Value: 3. - Articles can be sent to editor@impactjournals.us

Strength Performance of Concrete Using Bottom Ash as Fine Aggregate 117 containing 5%, 1%, 15% and % bottom ash as fine aggregate gained 67.46%, 67.73%. 68.17% and 71.6% of their 28 days compressive strength respectively as compared to 72% of 28 days compressive strength gained by control concrete mixtures. At curing age of 28 days, the compressive strength of concrete mixtures containing bottom ash as partial replacement of fine aggregate surpassed that of control concrete. The factors responsible for the decrease in compressive strength of bottom ash concrete mixtures at early curing age of 7 days can be due to the replacement of the stronger material with the weaker material and absence of pozzolanic activity by the bottom ash. The previous studies show that pozzolanic activity of coal bottom ash is slow until 14 days of curing age and after this period, the coal bottom ash particles start reacting with calcium hydroxide and forming C S H gel and needles [8]. It can be seen that 28 th day compressive strength of bottom ash concrete was increased with addition of microsilica. The results show that microsilica beyond 8 percentages has no influence on the strength gain in the mixes. In the present investigation the maximum increase in strength obtained at 8% of microsilica. Also with increase in percentage of microsilica content, the strength gain seems decreased. The main effect on the strength of microsilica is due to its reaction with lime in concrete and resulting better pore distribution in its matrix. That is there is a need for an amount of microsilica to complete these actions. Any extra quantity of microsilica merely will be dust filler in concrete. That is the reason why no significant strength gain in concrete observed when percentage of microsilica is more than 8%. Splitting Tensile Strength Test The splitting tensile strength results of bottom ash concrete mixtures are shown in Figure 7. The results of bottom ash concrete with microsilica are shown in Figure 8. 5 28 th day split tensile strength of bottom ash concrete 4 split tensile strength 3 2 1 5 1 15 25 3 35 percentage of bottom ash Figure 7: Effect of Bottom Ash in Split Tensile Strength of Concrete 5. 28th day split tensile strength of bottom ash concrete with microsilica 4.5 4. 3.5 split tensile strength 3. 2.5 2. 1.5 1..5. 2 4 6 8 1 12 14 16 18 percentage of microsilica Figure 8: Effect of Microsilica in Split Tensile Strength of Bottom Ash Concrete Impact Factor(JCC): 1.5548 - This article can be downloaded from www.impactjournals.us

118 Remya Raju, Mathews M Paul & K. A. Aboobacker The test results indicate that inclusion of bottom ash in concrete improved the splitting tensile strength of concrete. The splitting tensile strength of concrete is more dependent on the quality of the paste than compressive strength. The properties of fine aggregate also affect quality of paste and interfacial transition zone in the concrete, which affect the ratio of tensile strength and compressive strength. The pozzolanic properties of bottom ash improves the quality of the paste thereby result in increase in splitting strength of concrete. The splitting tensile strength results of this investigation are in good agreement with those reported by Malkit Singh et al. [1]. At curing age of 28 days, the splitting tensile strength of bottom ash concrete mixtures incorporating 5%, 1%, 15%, % and 25% bottom ash as fine aggregate was 14.28%, 12.11%, 1.8%, 11.48% and 6.21% higher than that of control concrete mixture respectively. The incorporation of bottom ash in concrete shows significant increase in splitting tensile strength. Flexural Strength Test Results In this test, plain concrete beam was subjected to flexure using symmetrical two point loading until failure occurs. The theoretical maximum tensile stress reached in the bottom fiber of the test beam is called modulus of rupture. The results of flexural strength test were tabulated in Table 7. Sl. No Table 7: Results of Modulus of Rupture Mix Designation 1 BAC 2 BAC 5 3 BM 8 Ultimate Load in Tones Modulus of Rupture in N/mm 2 3. 5. 2.8 4.97 3.2 5.68 2.8 4.97 2.9 5.15 3.1 5.51 2.5 4.44 2.7 4.8 2.1 3.73 Modulus of Rupture in N/mm 2 Even though the compressive strength was increased, the flexural strength of concrete almost decreased when fine aggregate was replaced by bottom ash. The cracks caused by flexural load easily propagated through bottom ash particles while the normal aggregates were hard to penetrate, and consequently the direction of the crack propagation was changed by the existence of normal aggregates. Therefore, the flexural strength of concrete was decreased when bottom ash aggregates were applied. However, advanced studies have to be carried out to investigate the mechanisms of crack nucleation and propagation during compressive and flexural loading for concrete incorporating bottom ash. Water Absorption Water absorption of concrete specimens was determined as per the procedure given in relevant ASTM specification [18]. The concrete cubes of 7 days curing age free from visible cracks, fissures etc. were used in this investigation for determining the water absorption. The results of water absorption are illustrated in Tables 8 and 9. 5.28 5.21 4.32 Table 8: Water Absorption of Bottom Ash Concrete Mix Designation Water Absorption (%) at 28day Curing Age BAC 5.9 Index Copernicus Value: 3. - Articles can be sent to editor@impactjournals.us

Strength Performance of Concrete Using Bottom Ash as Fine Aggregate 119 Table 8:Contd., BAC 5 5.82 BAC 1 6.15 BAC 15 6.49 BAC 6.9 BAC 25 7.6 BAC 3 7.21 Table 9: Water Absorption of Bottom Ash with Microsilica Concrete Concrete Mixture Water Absorption (%) at 28 th day Curing Age BM 5.82 BM 4 5.7 BM 6 5.81 BM 8 5.75 BM1 6.18 BM 12 6.32 BM 15 6.51 The test results show that water absorption of concrete increased with the increase in levels of fine aggregate replacement by coal bottom ash in concrete. The results proved the correlation between the permeable pore space and water absorption. With the addition of bottom ash in concrete, the connectivity between the capillaries in the paste improved. When microsilica was added to the mixture the water absorption was slightly reduced. This may due to the finer particles of microsilica. Beyond 8% replacement there was not much reduction in water absorption. Results of Modulus of Elasticity Modulus of elasticity of concrete mixtures was measured at the curing age of 28 days. The test results are shown in Tables 1 and 11. 28th day modulus of elasticity of bottom ash concrete modulus of elasticity 3 1 5 1 15 25 3 35 percentage of bottom ash Figure 9: Effect of Bottom Ash on Modulus of Elasticity of Concrete 28th day modulus of elasticity modulus of elasticity 3 1 2 4 6 8 1 12 14 16 18 percentage of microsilica Figure 1: Effect of Microsilica in Optimum Bottom Ash Concrete on Modulus of Elasticity Impact Factor(JCC): 1.5548 - This article can be downloaded from www.impactjournals.us

1 Remya Raju, Mathews M Paul & K. A. Aboobacker Even though the compressive strength was not strongly affected, the modulus of elasticity of concrete decreased approximately linearly with the increase in replacement levels of fine aggregate with the bottom ash. The modulus of elasticity of bottom ash concrete mixtures was lower than that of control concrete mixture at the curing age of 28 th day. Hence, as far as strength properties and modulus of elasticity are concerned, the concrete produced using bottom ash is suitable for structural purposes. When microsilica was added to the bottom ash concrete, it can be seen that there is decrease in the modulus of elasticity. From these results it is evident that bottom ash strongly affects the elastic behavior of concrete. CONCLUSIONS The present investigation was carried out to evaluate the suitability of utilizing bottom ash as a partial replacement of fine aggregates in M35 grade concrete. The study also investigated the effect of microsilica in optimum bottom ash concrete mix. Test results indicate that bottom ash from Hindustan Newsprint Limited is a suitable material to be used as fine aggregate in partial replacement of fine aggregate along with microsilica in production of structural concrete. Based on the analysis of test results and discussions following conclusions can be drawn. The workability of bottom ash concrete decreased on use of coal bottom ash in partial replacement of fine aggregate in concrete. When micro silica was added to bottom ash concrete workability again decreases. Compressive strength reduced marginally on the inclusion of bottom ash in concrete. No significant strength gain in concrete observed when percentage of microsilica is more than 8%. Splitting tensile strength of concrete improved on use of coal bottom ash as fine aggregate in partial replacement of sand and also when micro silica was added to the optimum mix. The flexural strength of concrete almost linearly decreased as the replacement level of bottom ash was increased. Water absorption of bottom ash concrete at 28 days curing age also increased approximately linearly with the increase in replacement levels of fine aggregate with bottom ash in concrete. When microsilica was added to the mixture the water absorption was slightly reduced. The modulus of elasticity of concrete decreased approximately linearly with the increase in replacement levels of fine aggregate with the bottom ash. REFERENCES 1. Malkit Singh et al. Strength properties and micro-structural properties of concrete containing coal bottom ash as partial replacement of fine aggregate, Construction and Building Materials 5; 246 256. 2. Bumjoo Kim et al. Geotechnical Properties of Fly and Bottom Ash Mixtures for Use in Highway Embankments Journal of Geotechnical and Geoenvironmental Engineering asce/july 5. 3. P. Aggarwal, Y. Aggarwal, S. M. Effect of bottom ash as replacement of fine aggregates in concrete Asian Journal of Civil Engineering (building and housing) vol. 8, no. 1 (7). Index Copernicus Value: 3. - Articles can be sent to editor@impactjournals.us

Strength Performance of Concrete Using Bottom Ash as Fine Aggregate 121 4. Abdulhameed et al. Properties of concrete using tanjung bin power plant coal bottom ash and fly ash, International Journal of Sustainable Construction Engineering & Technology (ISSN: 218-3242) Vol 3, Issue 2, 12. 5. M. P. Kadam et al. Effect of coal bottom ash as sand replacement on the properties of concrete with different w/c ratio International Journal of Advanced Technology in Civil Engineering, ISSN: 2231 5721, Volume-2, Issue-1, 13. 6. P. Tang et al. The application of MSWI bottom ash fines in high performance concrete, 1st International Conference on the Chemistry of Construction Materials (12). 7. Yogesh Aggarwal, Rafat Siddique, Microstructure and properties of concrete u sing bottom ash and waste foundry sand as partial replacement of fine aggregates, Construction and Building Materials 54 (14) 21 223. 8. C. Mathiraja, A Study on Concrete Using Bottom Ash, Manufacturing Sand and Hybrid Steel and Coir Fibres, IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) Volume 1, Issue 1 (Nov. - Dec. 13), PP 55-57. 9. Kim H K, Lee H K, Use of power plant bottom ash as fine and coarse aggregate in high-strength concrete, Constr Build Mater 11; 25:1115 22. 1. IS 12269-1987 Indian Standard specification for 53grade ordinary Portland cement Bureau of Indian Standards, New Delhi, 1997. 11. IS 2386-1963 (part 3), Methods of test for aggregates for concrete, Bureau of Indian Standards, New Delhi, 1997. 12. IS 383-197 Specification for coarse and fine aggregates from natural sources for concrete, Bureau of Indian Standards, New Delhi, 1997. 13. IS 516-1959, Indian Standard methods of tests for strength of concrete, Bureau of Indian Standards, New Delhi, 1997. 14. IS 1199-1959, Methods of sampling and analysis of concrete, Bureau of Indian Standards, New Delhi, 1997. 15. IS 1262-9, Indian Standard recommended guidelines for concrete mix design, Bureau of Indian Standards, New Delhi, 1997. 16. IS 186-1982 Specification for moulds for use in tests of cement and concrete, Bureau of Indian Standards, New Delhi, 1997. 17. ASTM C642-97. Standard test methods for density, absorption and voids in hardened concrete. West Conshohocken, USA: ASTM International; 1997. 18. BIS: 8112-1989. Indian standard 53 grade ordinary Portland cement specification, New Delhi, India: Bureau of Indian Standards; 1989. 19. BIS: 5816-1999. Indian standard splitting tensile strength of concrete-test method, New Delhi, India: Bureau of Indian Standards; 1999. Impact Factor(JCC): 1.5548 - This article can be downloaded from www.impactjournals.us