Dow Pharma Solutions. ETHOCEL High Productivity (HP) Polymers Safe. Fast. Efficient.

Similar documents
ETHOCEL High Productivity (HP) Polymers Safe. Fast. Efficient.

ETHOCEL High Productivity (HP) Polymers Safe. Fast. Efficient.

Pharma & Food Solutions. ETHOCEL One of the Few Water-Insoluble Polymers Approved for Global Pharmaceutical Applications

METHOCEL. TM Trademark of The Dow Chemical Company ( Dow ) or an affiliated company of Dow

FILM COATINGS. Process Adaptability for the Perfect Finish. Productivity Enhancement and Efficiency Wide Processing Latitude Excellent Appearance

Film Coating Process Considerations for the Application of High Productivity, High Solids Concentration Film Coating Formulations

UCARSOL GT 900 Antifoam

Real-Time Prediction of Polymer-Coated Multiparticulate Dissolution using Process Analytical Technology

One non-numeric process related variable examined was post coating thermal (curing) treatment.

Product Portfolio. Construction

Influence of Film Coating Process Parameters on the Gloss of Tablets Coated with Pigmented Aqueous Film Coating Formulations

Investigation of a Venlafaxine HCl (37.5 mg) Extended Release Formulation Using Hypromellose (HPMC) Matrices

AVANSE ST-410 Acrylic Emulsion

Extended-release Venlafaxine Pellets: Scaling Up the Coating Process Stuart C. Porter, Bradley Beissner and Jeffrey Williamson

Investigation of a New Coating Process for the Application of Enteric Coatings to Small Tablet Samples

7th Training School on Microencapsulation Strasbourg. Februar 2015 Textmasterformat in Mastervorlage eingeben

OPADRY II. Application Data

PARALOID TMS-2670 MBS Impact Modifier For Epoxy Resin Applications

Pharma Ingredients & Services. Kollicoat IR White. Technical Information

MAINCOTE 1100A Emulsion Advanced Resin for Industrial Coatings based on AVANSE Technology Platform

PARALOID EXL-2655 Impact Modifier For Thermoset Applications

DUOLITE AP143/1073. Pharmaceutical Grade Anion Exchange Resin

Preparation of Robust, Enteric Coated Dosage Forms Utilizing Acryl-EZE and Aluminum Lake-Based Pigments

PARALOID EXL-5900 Optical Properties Modifier For Polycarbonate and Polystyrene

PARALOID EXL-2690 IMPACT MODIFIER

ROPAQUE OP-96 All-Purpose Pigment Engineered to Improve Waterborne Coatings

Chemical Resistance of TRENCHCOAT Protective Film

UCARSOL AP 804 and AP 806 Solvents

SELEXOL Booster. Boosting the Performance of Physical Absorption Processes

AMP-95. Key Performance Advantages. (2-amino-2-methyl-1-propanol containing 5% water) Multifunctional Additive for Latex Paints

Case and Carton Sealing: Hot melt Adhesive Solutions

IMPACT MODIFIER (21518XP) Maleic Anhydride (MAH) Grafted Polyolefin for Polyamide Applications

ADVANTAGES OF MULTIPARTICULATES (PELLETS):

Flexible Acrylic Resin XP Translucent Grade

AMP-95. Key Performance Advantages. Multifunctional Additive for Latex Paints. We make the best perform better.

Polyurethanes for roller coating ROLLERS

OPTIDOSE 4210 Traceable Polymeric Acid Scale Inhibitor and Dispersant

ACUMER 2200 High Performance Scale Inhibitor

Mining and Quarrying. HYPERLAST TM and DIPRANE TM Elastomers

Investigation of Aqueous Ethylcellulose Dispersion in Extended Release Metformin Inert Matrices

ROPAQUE Ultra E Opaque Polymer

PARALOID EXL-2620 (Powder) MBS Impact Modifier For Polycarbonate, Polyesters and their Blends

Let s jointly advance better building. WALOCEL MKW Methyl Cellulose Powering Performance of High Quality Cement Renders. Dow Construction Chemicals

NORKOOL Industrial Coolants

Temperature stability of anion exchange resins

TAMOL 960 TAMOL 731A Scale Inhibitors

Construction Chemicals. Cellulosics and Redispersible Powders Product Guide

RHOPLEX SG-10M 100% Acrylic Emulsion For Interior/Exterior Semigloss Latex Paints

NORTH AMERICA EPOXY CURING AGENTS EPOXY

OUDRASperse WB 3001 Waterborne Epoxy Dispersion

FASTRACK HD-21A Polymer Emulsion for Durable Waterborne Traffic Marking Paints

ROVACE 9400 Vinyl Acrylic Binder

SURECEL 445 FOAM CELL PROMOTER

One resin can t possibly focus on all of these diverse needs. Now, however, one family of polyethylene resins can.

ACUMER 9400 High-Performance Dispersant for Various Minerals

Scuffing Measurement Methodology and Improved Film Coating Systems

DOW AMBERLITE and DUOLITE Ion Exchange Resin Excipients

ACUMER 9300 Dispersant Polymer for Mineral Slurries

DOW PuraGuard Propylene Glycol USP/EP. Your Security for Purity

Understanding FDA Food Packaging Regulations

Material handling and industrial engineering. HYPERLAST TM and DIPRANE TM Elastomers

Coathylene Polymer Powders

DOW Specialty Membrane XUS and XUS Reverse Osmosis Elements

OPTIDOSE 1000 Traceable Polymer A Tool for Maintaining Maximum Heat Transfer

Innovative material science for pipe applications from a global technology leader

Insulating and Protecting Flowlines and Subsea Equipment

INNOVATION DRIVING PERFORMANCE AND FOR ROTATIONAL MOLDING APPLICATIONS

PARALOID Edge 2301 Resin

Thermal and Rheological Evaluation of Pharmaceutical Excipients for Hot Melt Extrusion

NEXT GENERATION DOWEX MARATHON ION EXCHANGE RESINS FOR INDUSTRIAL WATER TREATMENT. Small change, big impact.

DOW TG-10 Specialty Amine For Gas Treating

ELASTENE 404 Binder. Pure Acrylic Binder For Elastomeric Coatings. * Manufactured without the use of APEO surfactants

Silane Crosslinking of Low Voltage Wire and Cable Applications of ENGAGE ENR / LLDPE Blend

PHARMACEUTICAL TECHNOLOGY REPORT. Introduction

EVALUATION OF NEW FILM COATING PROCESSES AND MATERIALS

AMBERLITE IRN160 H/OH Ion Exchange Resin

FOSSIL POWER PLANT WATER TREATMENT. Generating optimal performance, powered by Dow.

RHOPLEX MULTILOBE 400 Emulsion Polymer

PARALOID EXL 2314 Impact Modifier

Dow Corning Solutions for Office Equipment and Home Electronics

improved hot melt adhesives for hard-to-bond substrates

OUDRACure WB 8002 Waterborne Epoxy Curing Agent

TABLET COATING. Lec. 8

PARALOID AU-608 TBZ Acrylic Polyol For Auto Refinishing, GIF and Conventional Spray Applications, and Airless Spray Maintenance

MEETING YOUR CHALLENGES TODAY AND TOMORROW. Avicel PH BINDERS

CHAPTER 8: SOLID DOSAGE FORM COATING TECHNOLOGY NOOR MUHAMMAD SYAHRIN BIN YAHYA INTRODUCTION

PRIMAL SF-208ER Binder

Creating bio-based polyols for adhesives and sealants

AN INTRODUCTION TO SPHERONIZATION (MARUMERIZATION * )

LS-3140 OPTICALLY CLEAR ENCAPSULATION GEL

The Use of Klucel Pharm Hydroxypropylcellulose to Increase the Utility of Hydroxypropyl Methylcellulose in Aqueous Film Coating

PCB and Systems Assembly. Consumer Solutions. Flexible Options for Processing, Protection, and Performance from a Conformal Coating.

PCB and Systems Assembly. Consumer Solutions. Flexible Options for Processing, Protection, and Performance from a Conformal Coating.

PARALOID AU-1033 Acrylic Polyol with Low Isocyanate Demand For Coatings on Recreational Equipment and Fleet Refinishing

paper tech Unique Flexible Epoxy Systems for Flooring and Secondary Containment Leo Meilus EPIKOTE EPON EPI-CURE EPI-REZ HELOXY CARDURA VEOVA

D.E.R. 330 Liquid Epoxy Resin

This product is suitable for use in applications such as: Civil Engineering Marine and Protective Coatings

RHOPLEX EP-6060 Acrylic Polymer For Factory-Applied Wood Coatings

MAINCOTE 1071 Emulsion

ENOVA AEROGEL coatings

Transcription:

Dow Pharma Solutions ETHOCEL High Productivity (HP) Polymers Safe. Fast. Efficient.

Improving Productivity Through Innovation ETHOCEL Polymers is the oldest trademarked brand available from The Dow Chemical Company and continues to be an exciting source of innovation. The constant pursuit of production excellence has differentiated ETHOCEL from the competition by producing ethylcellulose that adheres to exceptionally narrow viscosity limits, contains fewer insoluble fibers and is more reproducibly ethoxylated than other ethylcellulose producers. With this latest innovation, ETHOCEL has been optimized for use in dry powder layering processes using rotor granulation technology. Rotor granulation technology enables coating of multiparticulates, powders and even mini-tablets without the need for solvents or aqueous-based polymer dispersions. The dry powder process uses just enough moisture to allow the polymer to adhere to the substrate, but the polymer is added as a dry powder. The new tailored ETHOCEL HP offering is ideally suited for the dry powder coating process. Trials show that using ETHOCEL HP (High Productivity) in a rotor coater allows for improved efficiency and shorter coating times, while completely eliminating the need for environmentally-harmful solvents. This new technology can be a powerful solution for customers looking to improve sustainability metrics or avoid installation of costly solvent handling systems without experiencing the long coating time and potential stability issues of aqueousbased dispersions. Figure 1. VFC-LAB 3 FLO-COATER with GXR-35 Rotor Insert. Customers looking for innovative solutions to their controlled release and taste masking challenges will find that using ETHOCEL HP in a dry powder coating process gives them the confidence of working with a familiar and well understood ETHOCEL polymer while avoiding concerns with tackiness and stability often found with other barrier membrane solutions. Commercial availability of the ETHOCEL HP product is the culmination of an extensive collaboration between equipment manufacturer Freund-Vector Corporation, developers of the innovative GRANUREX rotor processing equipment and Controlled Release Alliance partner Colorcon, with their industry leading SUGLETS sugar spheres product for drug layering. Formulation development support and distribution of ETHOCEL HP will be managed by the Controlled Release Alliance and led by Colorcon. Why Go With This Solvent-Less System? ETHOCEL HP can help you: Realize 7% improvements in processing time versus current MUPS coating technologies Consistently achieve 98-99% coating efficiency Improve sustainability through elimination of solvents Avoid additional costs related to solvent use including disposal, capital and infrastructure modifications Improve operational safety Figure 2. GRANUREX GXR-35 Rotor. 2

Atomization of Solution ETHOCEL in organic solvent or as aqueous dispersion sprayed onto substrate Droplet spreading and evaporation Layer Formation Process repeated thousands of times to form uniform film ETHOCEL Layer Formed Figure 3. The spray coating process. Final Film Formation Final Film Formation How The Spray Coating Process Works Typical spray coating systems of ethylcellulose rely on dissolution of the polymer in a solvent to apply the coating onto the substrate. The film formation process occurs by atomizing the solution into small droplets that coalesce on the surface of the substrate allowing the carrier medium to evaporate, leaving an ethylcellulose film on the surface of the substrate. This process is repeated thousands of times during the coating process, resulting in many layers of ethylcellulose that coalescence into a solid, homogenous film. This process is well understood and allows for great film-formation resulting in stable, reproducible coatings. A similar process can also be used with aqueous dispersions of ethylcellulose, but with the additional requirement of a curing step to relax the ethylcellulose particles into a coherent film. Figure 4. Cross sectional image (left) and magnified view (right) of ETHOCEL barrier membrane formed from solvent solution. Initial wetting and powder feeding ETHOCEL HP Tacking Agent: Water & Plasticizer Rotor Layering (rolling snowball effect) Repeated liquid and solid bridging Figure 5. The dry powder layer process. Curing to induce coalesence Final Film Formation How The Dry Powder Layering Process Works The dry powder layering process applies the ethylcellulose from a dry state onto a substrate by wetting the substrate with a tacking agent comprised of plasticizer and water. Immediately after wetting, the dry polymer powder is applied to the surface of the substrate with the wetting agent acting as a bridge between the dry powder particles and the surface of the substrate. The presence of the plasticizer lowers the glass transition temperature (Tg) of the polymer to allow the particles to soften and fuse in a subsequent curing step. The wetting agent and dry powder are continually sprayed on to the substrates, building additional polymer layers very quickly. After sufficient coating, the dry powder coated substrates are cured through a heating step which can often be performed in the unit while the substrates continue to spin in the rotor. The dry powder process greatly improves efficiency as the wetting liquid and powder are directly placed into the substrate bed. The process equipment is extremely versatile, allowing APIlayering, polymer coating and film curing to occur within the same piece of equipment Figure 6. Cross sectional image (left) and magnified view (right) of ETHOCEL HP barrier membrane formed from dry powder rotary coating process. 3

How Does ETHOCEL HP Work In This Process? ETHOCEL HP was specifically designed for enhanced performance in a dry powder coating process. The mean particle size and particle size distribution have been optimized for controlled release performance. These case studies demonstrate product attribute effects and improvements over standard manufacturing technologies in enhanced productivity, decreased coating times, and better environmental impacts by removing solvent use. Table 1. Particle size specification (in microns). Particle size specification ETHOCEL Std ETHOCEL FP ETHOCEL HP D1 N/A N/A < 3 Mean N/A 3-15 < 8 D9 N/A N/A < 15 Maximum N/A 1 N/A Since ethylcellulose is applied from the dry state, a curing step is required to ensure proper film formation and stability. Curing can be done in-situ in the equipment (referred to as dynamic curing ) or in tray ovens ( static curing ). Table 1 shows the extremely narrow particle size distribution of ETHOCEL HP which allows for optimal particle packing when applied as dry particles. Broad particle size distributions have the potential to interfere with efficient particle arrangement and can result in voids or film defects. Improving Particle Size For Improved Film Formation Acetaminophen drug release was determined for % weight gains of ETHOCEL milled to various mean particle size and particle size distributions (Figure 7). 25% dibutyl sebacate plasticizer was used with respect to ethylcellulose weight and was dissolved in water and added with the wetting liquid. No pore formers were used and all samples were statically cured for 2 hours at 6 C. As mean particle size was reduced and particle size distributions were tightened, film formation was improved resulting in more controlled release of the active ingredient. Larger mean particle sizes resulted in highly porous films even after curing, whereas micronized ETHOCEL resulted in a fully formed film and slowest drug release. 9 8 X : 5um 7 %APAP Released 6 5 3 1 X : 24um X : 5um 8 1 16 Figure 7. Influence of particle size on film formation and drug release. X: 5um X: 24um X: 5um Table 2. Particle size distributions of ethylcellulose samples. Sample D1 (µm) Mean (µm) D9 (µm) ETHOCEL HP 1 5 9 Medium Size 4 24 55 Large Size 8 5 18 4

% Metoprolol Released ETHOCEL HP Polymers Fast Coating Times and Weight Gain Influence Figure 8 illustrates how the dry powder delivery of ETHOCEL HP Polymers significantly reduce process times for a full scale 25kg batch as compared to aqueous ethylcellulose and organic ETHOCEL. The data presented includes a 2 hour cure step required for applications of aqueous dispersions of ethylcelluose and a 3 minute cure step required for ETHOCEL HP. For example, at % weight gain, a full scale 25kg batch with ETHOCEL HP can be completed in under 2 hours whereas organic ETHOCEL requires 12 hours and aqueous ethylcelluose 8 hours. Metoprolol Tartrate drug release was determined for ETHOCEL HP barrier coatings ranging from 15-3% weight gain. % plasticizer (75:25 oleic acid:dbs) was used with respect to ETHOCEL HP weight and dissolved in water. No pore formers were used and samples were dynamically cured for 1 hour at an inlet air temperature of 8 C. Figure 9 shows how drug release was predictably controlled by incremental weight gain. Process Time (hr) 18 16 14 12 1 8 6 4 2 Organic ETHOCEL (Feed Rate: 71 g/min) Aqueous ETHOCEL (Feed Rate: 135 g/min) ETHOCEL HP (Feed Rate: 6 g/min) % 5% 1% 15% % 25% 3% Weight Gain Figure 8. Equivalent performance coating times including curing. 1 1 8 6 15% WG % WG 25% WG 3% WG 2 48 7 96 1 Figure 9. Influence of ETHOCEL HP weight gain on Metoprolol Tartrate drug release. Equivalent Performance to Solution Coating Metoprolol tartrate drug release was determined for % weight gain of ETHOCEL HP. % dibutyl sebacate plasticizer was used with respect to ETHOCEL HP weight and dissolved in water. No pore formers were used and samples were statically cured for 2 hours at 6 C. Metoprolol tartrate drug release was also determined for 1% weight gain of ETHOCEL Std 1 Premium which was dissolved in 9% isopropanol and 1% water. 1% dibutyl sebacate plasticizer was used with respect to ETHOCEL Std 1 Premium weight and dissolved in the same solution. No pore formers were used and samples were not cured. The ETHOCEL HP applied at % weight gain has equivalent performance to organic ETHOCEL applied at 1% weight gain without any lag in drug release in the first 6 minutes (Figure 1). Although a higher amount of ETHOCEL HP was needed in this example, total coating time only took 221 minutes including the 2 hour cure step whereas organic ETHOCEL took 293 minutes. More time saving could have been achieved by switching to dynamic curing. Dissolved (%) 1 9 8 7 6 5 3 1 ETHOCEL HP - uncured ETHOCEL HP - static cured 6 C - 2hrs Organic EC-1% WG 6 8 1 1 Figure 1. Metoprolol tartrate drug release for ETHOCEL HP rotary coatings and organic ETHOCEL spray coatings. 5

Curing Influence Due to the dry powder nature of the rotary coating process, a cure step is required to achieve full film coalescence. Film coalescence is obtained through appropriate selection of plasticizers during the powder application step and adequate product temperature during a dynamic curing step. Dynamic curing is a time saving process which allows the film curing step to take place in the rotor processor in a true one step, one pot process. Heated forced air, also known as drying air, is introduced at the end of the coating process to remove residual moisture and begin the curing process while the beads continue to rotate. The result is polished, opalescent beads with a smooth, continuous ethylcellulose film coating. Evidence of full film formation can be obtained visually and is confirmed by reproducible drug release upon accelerated stability testing. Experiments have demonstrated that several well-known plasticizers can be effectively used with ETHOCEL HP Polymers. Figure 11 shows the glass transition temperature (Tg) of ETHOCEL HP films with several common plasticizers and their combinations. Plasticizer combinations, especially those with oleic acid, were particularly effective at lowering the Tg of ETHOCEL HP. Selection of an appropriate plasticizer package may be formulation dependent, but for the best results the product temperature should reach 1 C above the Tg of the ETHOCEL HP / plasticizer combination. An example of product temperature profiles obtained with a 2 kg R&D Scale rotor granulator set to 6 C and 8 C drying air can be seen in Figure 12. Tg ( C) 7 6 5 3 Oleic Acid TEC DBS 1:1 OA:TEC 1:1 OA:DBS 3 5 % Plasticizer Figure 11. Glass transition temperatures of ETHOCEL films with plasticizers at various concentrations. Product Temperature ( C) 5 45 35 3 25 6 C Inlet Air 8 C Inlet Air 15 6 8 1 Total Process Figure 12. Product temperature profile of multiparticulate beads during ETHOCEL HP coating and dynamic curing at two different drying temperatures. Figure 13. Cross-sectional images of uncured (left) and cured (right) samples coated with ETHOCEL HP. Figure 14. Surface morphology of ETHOCEL HP coated multiparticulate after dynamic curing. 6

Stability Consistency in drug release performance over extended storage times is an important consideration for formulation performance and serves to demonstrate that adequate curing of the ETHOCEL HP Polymers film has occurred. In the examples below, two different plasticizers were used in conjunction with two different sets of curing temperatures, with both resulting in stable drug release profiles under accelerated stability conditions ( C/75% RH). 1 1 1 1 % MT Released 8 6 Initial 1 month 3 month 6 month % MT Released 8 6 Initial 1 month 3 month 2 48 7 96 1 2 48 7 96 1 Figure 15. Drug release stability of ETHOCEL HP coated Metoprolol tartrate multipaticulates prepared with % DBS plasticizer and dynamically cured at C product temperature. Figure 16. Drug release stability of ETHOCEL HP coated Metoprolol tartrate multipaticulates prepared with % DBS plasticizer and % oleic acid and dynamically cured at 5 C product temperature. ETHOCEL High Productivity is an innovative new product which helps customers increase productivity while still maintaining the advantages of Dow manufactured ETHOCEL such as tight viscosity, narrow ethoxyl distribution, and reduced fiber content. Using ETHOCEL HP could result in -7% reduction in process time versus solvent and aqueous spray coating systems. In addition to the controlled release market, ETHOCEL HP and the rotor technology can also be extended to taste masking to help eliminate the bitter taste of actives upon swallowing. Proven to be most effective as a solvent-less coating, this new technology enables customers to achieve processes which are sustainable, environmentally friendly, and safe for their employees. 7

Dow-Colorcon Alliance: UNIQUE TOGETHER Dow Pharma & Food Solutions and Colorcon, together in the Controlled Release Alliance, bring joint resources in polymer and formulation expertise to accelerate your pharmaceutical product development efforts and reach markets throughout the world. Colorcon has exclusive, global sales and distribution rights for Dow products used in controlled release applications, including ETHOCEL Polymers. For more information, contact your Colorcon representative or call: North America +1-215-699-7733 Europe/Middle East/Africa +44 ()-1322-293 Latin America +54-11-5556-77 China +86-21-619823 India +91-832-6727373 You can also visit our website at www.colorcon.com The Colorcon ellipse is a registered trademark of BPSI Holdings LLC. Dow Pharma & Food Solutions www.dowpharmaandfood.com US Toll Free 8 441 4DOW 989 832 1542 International Europe / Middle East + 8 36 94 63 67 Italy + 8 783 825 Asia / Pacific + 8 77 76 77 76 + 6 37 958 3392 South Africa + 8 99 578 Dow requests that customers considering use of Dow products in medical applications notify Dow so that appropriate assessments may be conducted. Dow has a Corporate Medical Application Policy in place that guides the use of Dow products in potential new pharmaceutical and medical device uses. Dow reviews all new applications/uses according to this Medical Application Policy to determine if the use is appropriate for Dow materials. Dow does not endorse or claim suitability of its products for specific medical applications. It is the responsibility of the medical device or pharmaceutical manufacturer to determine that the Dow product is safe, lawful, and technically suitable for the intended use. DOW MAKES NO WARRANTIES, EXPRESS OR IMPLIED, CONCERNING THE SUITABILITY OF ANY DOW PRODUCT FOR USE IN MEDICAL APPLICATIONS. NOTICE: No freedom from infringement of any patent owned by Dow or others is to be inferred. Because use conditions and applicable laws may differ from one location to another and may change with time, Customer is responsible for determining whether products and the information in this document are appropriate for Customer s use and for ensuring that Customer s workplace and disposal practices are in compliance with applicable laws and other government enactments. The product shown in this literature may not be available for sale and/or available in all geographies where Dow is represented. The claims made may not have been approved for use in all countries. Dow assumes no obligation or liability for the information in this document. References to Dow or the Company mean the Dow legal entity selling the products to Customer unless otherwise expressly noted. NO WARRANTIES ARE GIVEN; ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED. Trademark of The Dow Chemical Company ( Dow ) or an affiliated company of Dow Form No. 198-2324-716CDP