Impact of Temperature on Performance of Photovoltaic System at NIT Agartala Campus-A Case Study Impact of Temperature on Performance of Photovoltaic System at NIT Agartala Campus-A Case Study Samima Akter, Saptadip Saha and Priyanath Das Department of Electrical Engineering, National Institute of Technology, Agartala, Tripura, India E-mail-samima.akter1989@gmail.com; saptadip.saha@gmail.com; priyanath70@gmail.com Abstract: Now-a-days, renewable energy is used due to limited sources of fossil fuels. The performance of the photovoltaic (PV) system is mainly decreased due to shading and temperature variation. The objective of this work is to study the characteristics of the power-voltage curve (P-V curve), open circuit voltage (V OC ) and maximum power profile (P max ) with the variation of the temperature of a small PV system at National Institute of Technology Agartala campus (NITA), India. Simulation is done by using PSCAD/EMTDC. The experimental setup is installed on the rooftop of G plus 6 block of National Institute of Technology Agartala campus to validate the results of the simulation. The results reveal that the performance of the system deteriorates with increase in temperature. Keywords: Power improvement, Solar irradiation, Solar photovoltaic, Temperature effect, Voltage improvement Electricity I. INTRODUCTION Now-a-day, many countries widely promoted renewable energy for generation of power due to rising demand for electricity along with rising fossil fuel prices. Solar energy is the most important clean energy in the world among all renewable sources. Solar irradiance can be converted into electricity without using any external link by using the photovoltaic effect. We can utilise the solar power with minimum cost due to less generation cost. Photovoltaic (PV) cell is the most basic component of solar panel in a PV system. The performance characteristic curve of PV system directly varies with global irradiance, ambient temperature and other environmental conditions. The most important issue is the temperature increment, which causes the significant reduction in the panel output power, voltage and efficiency, etc. Electricity produced by PV panels in photovoltaic system is inversely affected by their operating temperature. It is the product of the level of sunlight and ambient air temperature, which was described by the author in [1-3]. An article on solar panel cooling techniques was reviewed in [4] and observed that evacuated tube collectors are the best option for solar cooling. In ref. [5] different types of solar cell s characteristics are analysed and observed that both the maximum power point position and current flows through the system are increased due to the radiation intensity growth of solar. 327 International Journal of Control Theory and Applications
Samima Akter, Saptadip Saha and Priyanath Das The performance of amorphous Si photovoltaic modules was discussed in [6] and shown that energy out from Si modules generally depends on spectrum distribution, whereas energy out from mc-si module depends on module temperature, not spectrum distribution. In [7], authors studied the effect of temperature on the performance of dense array concentrator PV system and it was observed that solar cells those are located in the middle region of the array experiences more heat as compared to lower portion cells. Most important factors (e.g. temperature, cable thickness, PV panel shading, charge controller and photovoltaic cell s I-V characteristics, inverter efficiency and battery efficiency) were discussed for photovoltaic system performance [8]. Temperature effect on different grid-connected PV technologies was analysed in [9] and observed that the coefficients range performance losses initially with temperatures above the maximum power point (MPP). In ref. [10], studied the temperature coefficient of dissimilar types of solar modules. Now-a-days, the demand for energy increases gradually in all over the world. But, our conventional energy sources are limited. Due to this reason, we are focusing on renewable energy among which solar energy plays an important role. The performance of solar systems decreases with increase in temperature above standard temperature condition (STC) of the panel. For this drawback, the temperature refrigeration technique is required. A review paper of hybrid adsorption refrigeration schemes in order to control the temperature was given in [11] which was shown to better the performance of the system. Estimation of PV panel temperature by artificial neural networks (ANN) was studied in [12]. The new temperature refrigeration system was proposed for improving the efficiency of solar cells between 12% and 14% [13]. The Author of ref. [14] studied the effect of variation of temperature on power efficiency consumed by electrodes. Behaviour of photovoltaic system with temperature variation was analysed in [15] and it was observed that the yearly energy output from the PV system increased with improvement in the temperature coefficient. Solar thermal refrigeration and cooling methods were reviewed in [16]. Power generation from solar system totally depends on panel s cell temperature. While the short circuit current (I SC ) rises marginally with increasing temperature. The open circuit voltage (V OC ) reduces considerably if temperature increases, leading to a reduction of maximum output power. II. AIM OF THIS PAPER Electricity produced by photovoltaic panels is affected by fault due to operating temperature variation, which are primarily a product of the ambient air temperature and the level of sunlight. Increase in temperature is one of the main challenges for photovoltaic systems which cause significant reduction in maximum output power (P max ), open circuit voltage profile (V OC ) and power-voltage characteristics. This paper discusses on the effect of fault on temperature variation on photovoltaic system performances at NIT Agartala campus. III. TEST SYSTEM DETAILS For the analysis of the impact of panel s temperature improvement on photovoltaic system, simulation model and experimental setup of the system is considered. The effect of panel s temperature improvement fault on open circuit voltage (V OC ) profile, maximum power profile of the photovoltaic system is analysed in simulation as well as outdoor experiment considering the constant irradiance (G) = 270 W/m2 and different temperature. The obtained data at temperature 25 0 C is assumed as a reference for the sake of better explanation. 3.1. Simulation details In a simulation study, two 60 watt PV panels are connected in series. Simulation part of the proposed test system is done in EMTDC/PSCAD which is shown in fig. 1. International Journal of Control Theory and Applications 328
Impact of Temperature on Performance of Photovoltaic System at NIT Agartala Campus-A Case Study Figure 1: Simulation model of two single PV panels connected in series at G=270 W/m2, T= 25 0C 3.2. Experimental details Two 60 W single photovoltaic panels (Akshaya solar power) and an ammeter are connected in series. A voltmeter is also connected in parallel to the panel. A rheostat is connected in series to measure the output voltage and current at different values of resistance. The short circuit current is measured at zero resistance and the open circuit voltage is measured directly across the output terminals of PV System. The different voltage and current are collected at different conditions of the rheostat. A Lux meter and a Pyranometer are also used to measure the light intensity and radiance, respectively. The experimental setup is shown in fig. 2. Figure 2: Experimental model of two single PV panels connected in series 329 International Journal of Control Theory and Applications
IV. RESULTS AND DISCUSSIONS Samima Akter, Saptadip Saha and Priyanath Das The results obtained after simulating the proposed model in PSCAD are shown in subsection 4.1. The change in PV system performance with change in panel temperature is also discussed. Experimental results are shown in subsection 4.2. The experimental results validate the results of simulation. 4.1. Simulation results Impact of fault on the PV system power-voltage curve, open circuit voltage and maximum power output characteristics are analyzed in simulation as well as outdoor experiment due to temperature variation. It is noticed that power - voltage profile graph of the PV system is inversely proportional with increase in temperature of the panel in a PV system. fig. 3, fig. 4, fig. 5, fig. 6 and fig. 7 show the variation of power-voltage curve of photovoltaic system at temperature 25 0 C, 29 0 C, 36 0 C, 43 0 C and 48 0 C, respectively. From the fig. 3, fig. 4, fig. 5, fig. 6 and fig. 7, it is obtained that the open circuit voltage and maximum output power decreases with increase in temperature of photovoltaic panel in a PV system. It reveals that the theoretical concept is validated by the results of simulation. The variation of voltage and power with change in temperature in simulation is tabulated in Table 1. It is observed from Table 1 that both open circuit voltage and maximum power are reduced remarkably with an increase in panel temperature in a PV system. It is also observed that 0.0789 volts average voltage profile and 0.0594 watts average power profile of the PV system depreciates with increase in /p C solar panel temperature. Table 1 Variations of voltage and power of PV system with temperature in simulation Parameter Temp 25 C Temp 29 C Temp 36 C Temp 43 C Temp 48 C V oc (volt) 37.66 37.38 36.90 36.42 36.08 P max (watt) 30.72 30.52 30.15 29.75 29.51 Average decrement of voltage / C increment of temperature Average decrement of power / C increment of temperature 0.0789 volts 0.0594 watts Figure 3: Power-voltage graph in simulation at T = 25 0 C Figure 4: Power-voltage graph in simulation at T = 29 0 C International Journal of Control Theory and Applications 330
Impact of Temperature on Performance of Photovoltaic System at NIT Agartala Campus-A Case Study Figure 5: Power-voltage graph in simulation at T = 36 0 C Figure 6: Power-voltage graph in simulation at T = 43 0 C 4.2. Experimental results Figure 7: Power-voltage graph in simulation at T = 48 0 C Two 60 W single photovoltaic panels (Akshaya solar power) are connected in series to analyse the result of temperature variation in solar panels in outdoor. It is obtained that power-voltage graph profile of PV system deteriorates with the increase in PV panel temperature in photovoltaic systems. Figure 8 shows the variation of power and voltage flow through photovoltaic system at T=25 0 C in NIT Agartala campus, India. Similarly, fig. 9, fig. 10, fig. 11 and fig. 12 show the variation of power-voltage curve of photovoltaic system at temperature 29 0 C, 36 0 C, 43 0 C and 48 0 C, respectively. The combined power-voltage curve of the PV system is shown in fig. 13. 331 International Journal of Control Theory and Applications
Samima Akter, Saptadip Saha and Priyanath Das Figure 8: Power-voltage graph in real time at T = 25 0 C Figure 9: Power-voltage graph in real time at T = 29 0 C Figure 10: Power-voltage graph in real time at T = 36 0 C Figure 11: Power-voltage graph in real time at T = 43 0 C Figure 12: Power-voltage graph in real time at T = 48 0 C Figure 13: Power-voltage graph in real time at different temperatures International Journal of Control Theory and Applications 332
Impact of Temperature on Performance of Photovoltaic System at NIT Agartala Campus-A Case Study It is obtained from fig. 13 that power profile and voltage profile of proposed solar system is improved with decrease in panel temperature. The voltage and power profile of the PV system deteriorates with increase in temperature. Experimental results validate the concept of solar system performance with increase in temperature. The variations of voltage and power profile with change in temperature in real time are tabulated in Table 2. Table 2 Variations of voltage and power of PV system with temperature in real time Parameter Temp 25 C Temp 29 C Temp 36 C Temp 43 C Temp 48 C V oc (volt) 37.52 37.30 36.73 36.35 36.19 P max (watt) 30.75 30.41 30.29 29.80 29.49 Average decrement of voltage / C increment of temperature Average decrement of power / C increment of temperature 0.0726 volts 0.0645 watts It is observed from Table 2 that power and voltage profile of the proposed system decreases with the increase in PV panel temperature. The power-voltage graph is inversely proportional with photovoltaic panel temperature. It is also observed that the average decrement of voltage and power of the system is 0.0726 volts and 0.0645 watts respectively, with increase in /p C solar panel temperature in the PV system. The experimental results validate the results of simulation. V. CONCLUSION The performance of photovoltaic (PV) system depends on temperature variation. The power-voltage characteristics, open circuit voltage (V oc ) and maximum power (P max ) profile changes due to temperature variation. The experimental study is done on the rooftop of G plus 6 block of National Institute of Technology Agartala (NITA), India and simulation is done by using PSCAD/EMTDC software. The voltage and power of the proposed system deteriorates with the increase in solar panel temperature is observed from simulation and experimental result. In simulation, average voltage and power of solar system decreases correspondence to /p C improvement of temperature are 0.0789 volts and 0.0594 watts respectively, and from the experimental study, it is observed that decrements in average voltage and power profile correspondence to /p C improvement of temperature is 0.0726 volts and 0.0645 watts respectively in NIT Agartala campus APPENDIX-A Solar panel Type = Akshaya solar power panel Wattage of each panel = 60W Number of solar panel = 2 Sampling frequency (f s ) rate in simulation is 4 khz ACKNOWLEDGMENT The authors would like to thank The National Institute of Technology (NITA), India for providing support for carrying out research & development work in this field. REFERENCES [1] H. Najafi and K.A. Woodbury, Optimization of a cooling system based on Peltier effect for photovoltaic cells, Solar Energy, 2013, Vol. 91, pp. 152-160. 333 International Journal of Control Theory and Applications
Samima Akter, Saptadip Saha and Priyanath Das [2] D.M. Tobnaghi, R. Madatov and D. Naderi, The Effect of Temperature on Electrical Parameters of Solar Cells, International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering, 2013, Vol. 2, pp. 6404-6407. [3] C. Hill, The Effect of Temperature on Solar Panel Power Production, Demand Media 2014. [4] S. Anand, A. Gupta and S.K. Tyagi, Solar cooling systems for climate change mitigation: A review, Renewable and Sustainable Energy Reviews, 2015, Vol. 41, pp. 143-161. [5] L. A. Dobrzañski, L. Wosiñska, B. Do³ añska and A. Dryga³a, Comparison of electrical characteristics of silicon solar cells, Journal of Achievements in Materials and manufacturing Engineering, 2006, Vol. 18, pp. 215-218. [6] T. Minemoto, S. Nagae and H. Takakura, Impact of spectral irradiance distribution and temperature on the outdoor performance of amorphous Si photovoltaic modules, Solar energy materials and solar cells, 2007, Vol. 91, pp. 919-923. [7] F.L. Siaw, and K.K. Chong, Temperature effects on the performance of dense array concentrator photovoltaic system, In IEEE Conference on Sustainable Utilization and Development in Engineering and Technology, October 2012, pp. 140-144. [8] Anonymous, 6 Factors that Affect Solar PV System Efficiency, In Solar Power for Ordinary People, 2013, March. [9] G. Makrides, B. Zinsser, A. Phinikarides, M. Schuber and G.E. Georghiou, Temperature and thermal annealing effects on different photovoltaic technologies, Renewable Energy, 2012,Vol. 43, pp. 407-417. [10] P.K. Dash, Effect of Temperature on Power Output from Different Commercially available Photovoltaic Modules, International Journal of Engineering Research and Applications, 2015, Vol. 1, pp. 148-151. [11] A.A. Askalany, B.B. Saha, K. Kariya, I.M. Ismail, M. Salem, A.H. Ali and M.G. Morsy, Hybrid adsorption cooling systems An overview,renewable and Sustainable Energy Reviews, 2012, Vol. 16, pp. 5787-5801. [12] İ. Ceylan, O. Erkaymaz, E. Gedik and A.E. Gürel, The prediction of photovoltaic module temperature with artificial neural networks, Case Studies in Thermal Engineering, 2014, Vol. 3, pp. 11-20. [13] H.G. Teo, P.S. Lee and M.N.A. Hawlader, An active cooling system for photovoltaic modules. Applied Energy, 2012, Vol. 90, pp. 309-315. [14] I. Ksentini, K. Hmidi, N. Hajlaoui and L.B. Mansour, The effect of temperature on the efficiency of waste water treatment by electro flotation process supplied by solar energy, 6th International Renewable Energy Congress (IREC), 2015. [15] K. Nishioka, T. Hatayama, Y. Uraoka, T. Fuyuki, R. Hagihara and M. Watanabe, Field-test analysis of PV system output characteristics focusing on module temperature, Solar Energy Materials and Solar Cells, 2003, Vol. 75, pp. 665-671. [16] K.R. Ullah, R. Saidur, H.W. Ping, R.K. Akikur and N.H. Shuvo, A review of solar thermal refrigeration and cooling methods, Renewable and Sustainable Energy Reviews, 2013, Vol. 24, pp. 499-513. International Journal of Control Theory and Applications 334