OPDISYS Fiber to the Home - Solution

OPDISYS Fiber to the Home - Solution

Optical distribution system OPDISYS -rack The OPDISYS -rack was specially designed for Fiber-To-The-Home (FTTH) applications. It is a modular system consisting of a basic rack, cable management, mandrel extension racks and gasblocker extension racks and fiber modules. Thanks to its design this system is very flexible. The extension racks can be ordered and combined individually according to the customer s needs. Each fiber module has a front plate with two types of uniform cut-out patterns into which snap-in angled holders fitting into the required adapter type can be inserted. This snap-in angled holder also ensures a 45 degree angle of the adapter is maintained. Each fiber module can be used as a left-side as well as a right-side fiber module. By default, there are protection tubes from the cable clamp to each individual module is installed by kink-resistant PBT-tubes. They ensure that the minimum curve radius of the cable loose tubes from the cable entry to the fiber modules will not be exceeded. The cable clamps are pre-installed either on the top or on the bottom of the rack and are used to secure the strain relief of the incoming cables. They serve further as a fixing point for the cable tubes. Optionally, the strain relief element of the incoming cable to be attached. Technical data: maximum fiber density: 960 fibers at SC, 1920 fibers at LC and E2000 comfortable patching with two-sided overlength patchcord storage optional extensions (for cable guidance and gasblocker integration) available as open and closed rack version removable and rotatable splice/patch fiber module fiber module frontplate with different cutouts and adapter mounting through snap-in angled holder available: SC, LC, E2000 (others on request) optional integration of gas-blockers on incoming tubes possible (on request) colour: RAL 7035, light grey material: Powder coated steel flammability: UL 94V-0 The OPDISYS -rack is the core component of every OPDISYS -system. Both, an open version as well as a closed version, are available. An open version rack is turned into a closed version rack by installing side panels and doors. The rack accommodates the fiber module carrier, the cable entry plates, all types of extension modules and, if a closed version is required, the side panels as well as the front doors. Various fixing sets (see information in the accessories section of this document) are available which allow you to mount the rack to either wall or ceiling or floor. It is possible to mount several racks next to each other back-to-back (requires only floor mounting) or next to each other (requires mounting both to floor and ceiling or wall for stability reasons). A stand-alone Single Row Rack should always be fixed to both floor and ceiling or wall.

Rack features: top or bottom cable entry possible top cover provides openings for cables (optionally with brushes) easy expansion with side-by-side or back-to-back mounting of racks solutions for cross-connect and interconnect configurations backside vertical cable guidance for incoming cables bending radius protection of 30mm for fibers and patchcords intelligent patchcord management vertical patchcord cable guidance on left and right side mandrels on left and right side of the rack provide sufficient space for patchcord overlength storage integrated patchcord management to adjacent racks avoids the usage of external ducts Dimensions & capacity - standard version (incl. mandrels) Rack height Rack width Rack weight (open / closed) Max. amount of modules Max. amount of terminations OPDISYS -rack 1000/40HU incl. mandrels, protective tubes OPDISYS -rack 1000/40HU 2200 mm 1000 mm 118 kg / 170 kg 80 Full-Size or 160 Half-Size 960 SC 1920 LC / E2000 Art. No. 2735153 OPDISYS -rack - possible extensions (on request) Gasblocker - extension rack When using blow-in systems, gasblockers are essential in order to protect the installation against gas and/or water entry. The gasblocker extension rack can accommodate the gasblockers. It has a built-in back panel, so no extra back panel is needed in order to turn it into a closed version. Rack doors, side and back panels If a closed rack version is required, doors and panels can be attached to rack. Each door has an opening angle of 180. The doors are equipped with an integrated lever and lock and have an A4 document holder on their inner side. Each side panel is useable for right as well as for left side mounting. Gasblocker - extension rack on request Panels / door set Art. No. 2735154 OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 3

OPDISYS -rack - accessories Fixing sets Several fixing sets are available to mount the rack to the wall, on the floor or to mount multiple racks side by side or back to back to each other. Each individual fixing set contains all necessary screws, mounting brackets, washers and anchor pins. Tool kit adapter holder pincer The adapter holder pincer is designed to easily remove the snap-in angled holder from the frontplate cutout of the OPDISYS fiber module. Thanks to its small and compact design it ensures the smooth removal of a snap-in angled holder without interfering with other connections. torx socket wrench draw wire or element The draw wire or element tool is necessary to insert the incoming fiber cable into the fiber protection tube which is fed up to the fiber optic module. This tool is required to install a OPDISYS -System. Fixing set, back-to-back or side-to-side Art. No. 2735155 Fixing set for double bottoms Art. No. 2735156 Fixing set base with leveling feet Art. No. 2735157 Tool kit Art. No. 2735158 OPDISYS -fiber modules The multi-circuit management fiber modules are used as combined splice & patch modules. They offer highest fiber density along with best maintainability. Maximum flexibility is guaranteed by metal frontplates and 45 angled adapter holders for all conventional adapter types. The fiber modules are available as full-size fiber modules with a height of 1HU. Fiber modules can be equipped with different adapter types or with a closed frontplate without adapters for a splice-through version (in this case, a loop- back connection of fibers can be done via splices). The material of the LSZH fiber modules is a Polycarbonate / ABS blend. The symmetrical design of the multi-circuit management fiber modules allows you to use the same module for left- and right-side mounting. A uniform module colour optimizes stock keeping, while individual threefold colour code labelling (on front, side and cover) provides fast and clear module and fiber identification. On request we can deliver each fiber module with a customized labelling of the top cover (index of all ports with description) as well as a labelling of the side of each Fiber Module (indication of the street and the building this module is assigned to) according to the customer s request. Also the labelling of the fiber module numbering can be done by us. fiber modules can be rotated by 90 and are removable from the rack incoming fibers and pigtails are stored in separate areas easy to snap in adapter holders allow comfortable cleaning of pigtail-connector ferrules by taking off the adapter holders. identical splice protection holder for both shrink and crimp splice protection two-sided, easy to remove transparent covers per fiber module bending radius protection for all fibers and pigtails overlength storage of incoming cable subtube is possible on the bottom side of the module Technical Data: Colour RAL 7035, light grey Material Powder coated steel Flammability UL 94V-0 Weight (full size module) 145 grams (without adapters and pigtails) Each Fiber Module is equipped with a frontplate, snap-in angled holders, rubber shrink/crimp splice protection holder, fiber protection pipe holder, two transparent covers, designation label, door latch and inserted adapters and pigtails.

Plug-in configuration - fully equipped SC LC E2000 Amount of adapters 12 12 12 Amount of pigtails 12 24 24 Max. amount of spices Heat shrink splice protection* Crimp splice protection* Max. amount of spices 32 48 * Heat shrink splice protection or crimp splice protection are not included and must be ordered separately. Fiber module 24 LC/APC, 1HU Art. No. 2535159 Fiber module 24 E2000/APC, 1HU Art. No. 2535160 Fiber module 12 SC/APC, 1HU Art. No. 2535161 Fiber module for up to 48 splices, 1HU Art. No. 2535162 Cable clamp set Art. No. 2735163 OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 5

Patch cable PC LC/APC simplex, 2 mm Characteristics of LC/APC simplex: user-friendly audible latch to indicate proper mating push-pull locking plastic housing with zirconia ferrule standard IEC 61754-20 insertion loss (IL) for SM (typical) average value <0.15 db (to reference connector) maximum value <0.30 db (to reference connector) return loss (RL) >65 db 8 polishing (APC-polishing) strain relief 100 N PC LC/APC simplex 3 m Art. No. 2535164 PC LC/APC simplex 5 m Art. No. 2535165 PC LC/APC simplex 10 m Art. No. 2535166 PC E2000/APC simplex, 2 mm Characteristics of E2000/APC simplex: locks with locking lever automatic dust protection flap plastic housing with zirconia ferrule standard IEC 61754-15 insertion loss (IL) average value <0.10 db (to reference connector) maximum value <0.30 db (to reference connector) return loss (RL) >65 db 8 polishing (APC-polishing) PC E2000/APC simplex 3 m Art. No. 2535167 PC E2000/APC simplex 5 m Art. No. 2535168 PC E2000/APC simplex 10 m Art. No. 2535169 PC SC/APC simplex, 2 mm The patch cables consist of an inhouse cable with 2 mm outer diameter and is pre-assembled with two connectors. They are used to establish a connection between patch panels / cabinets or terminals. Because of their mechanical stability, patch cables can be used in cabinets, enclosures and with some restrictions in cable ducts. However, they may not be drawn in or injected. Characteristics of SC/APC simplex: automatic lock in adapter unlocks by pulling on housing ( push-pull ) plastic housing with zirconia ferrule standard IEC 61754-4 insertion loss (IL) (typical) average value <0.20 db (to reference connector) maximum value <0.30 db (to reference connector) return loss (RL) >65 db 8 polishing (APC-polishing) PC SC/APC simplex 3 m Art. No. 2535170 PC SC/APC simplex 5 m Art. No. 2535171 PC SC/APC simplex 10 m Art. No. 2535172

Fiber optic cable A-DQ(BN)2Y CT - Outdoor cable, center unitube, D35-S15 outdoor cable rodent protection metal-free longitudinally water-tight A-DQ(BN)2Y CT 12E9/125 Art. No. 2035132 A-DQ(BN)2Y CT 24E9/125 Art. No. 2035133 Type number of numbers of tube-ø tenisle strength outer-ø weight fibers / tube fibers approx. mm max. N approx. mm approx. kg/km A-DQ(BN)2Y CT 12E9/125 12 12 3,5 2000 8,5 72,8 A-DQ(BN)2Y CT 24E9/125 24 24 3,5 2000 8,5 73,7 Central loose tube cable for outdoor applications. Rodent protected by glass rovings. This cable is used as low fiber count data cable in distribution networks and meets the demands of outdoor environments. Fibers according ITU-T G.652.D Construction center unitube strength members (aramide yarns) PE-sheath, UV-resistant, black with two orange longitudinal stripes Fiber colours 1-12: red, green, yellow, blue, white, violet, orange, black, grey, brown, pink, turquoise 13-24: red, green, yellow, blue, white, violet, orange, transparent, grey, brown, pink, turquoise -each with black rings every 50 mm (max.) Tube colour red Laying usable for fixed laying in ducts or conduits and outdoors Marking double-sinus, phone-sign, meter marking, PENGG KABEL, year of manufacturing Technical Data tensile strength: compressive strength: impact strength: torsion: kink, cable: kink, tube: min. bending radius: temperature range: water penetration: according to IEC 60794-1-E1 according to IEC 60794-1-E3 value: 3000 N/10 cm according to IEC 60794-1-E4 value: 5 Nm according to IEC 60794-1-E7 value: 5 cycles ±1 turn according to IEC 60794-1-E10 value: The cables do not form a kink when a loop is drawn together to a diameter of 100 mm. according to IEC 60794-1-E16 value: The loose tubes do not kink. according to IEC 60794-1-E11 value: R = 20 x D (cable outer diameter) according to IEC 60794-1-F1 storage and transport: -40 C up to +70 C laying: -5 C up to +60 C operation: -25 C up to +70 C according to IEC 60794-1-F5 value: No water on free end. OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 7

A-DQ(BN)2Y GGT - Outdoor cable, loose tube construction, D23-S20 outdoor cable rodent protection metal-free longitudinally water-tight A-DQ(BN)2Y GGT 2x12E9/125 Art. No. 2035134 A-DQ(BN)2Y GGT 4x12E9/125 Art. No. 2035135 A-DQ(BN)2Y GGT 6x12E9/125 Art. No. 2035136 A-DQ(BN)2Y GGT 8x12E9/125 Art. No. 2035137 A-DQ(BN)2Y GGT 10x12E9/125 Art. No. 2035138 A-DQ(BN)2Y GGT 12x12E9/125 Art. No. 2035139 A-DQ(BN)2Y GGT 8x24 E9/125 Art. No. 2035140 A-DQ(BN)2Y GGT 18x24E9/125 Art. No. 2035141 Type number of number of tubes number of tube-ø tensile strength outer-ø weight fibers/tube + fillers fibers approx. mm max. N approx. mm approx. kg/km A-DQ(BN)2Y GGT 2x12E9/125 12 2 + 3 24 2,3 3500 13,2 141,7 A-DQ(BN)2Y GGT 4x12E9/125 12 4 + 1 48 2,3 3500 13,2 145,3 A-DQ(BN)2Y GGT 6x12E9/125 12 6 + 0 72 2,3 3500 13,5 160,0 A-DQ(BN)2Y GGT 8x12E9/125 12 8 + 0 96 2,3 3500 14,8 182,5 A-DQ(BN)2Y GGT 10x12E9/125 12 10 + 0 120 2,3 3500 16,3 214,0 A-DQ(BN)2Y GGT 12x12E9/125 12 12 + 0 144 2,3 3500 18,0 251,0 A-DQ(BN)2Y GGT 8x24E9/125 24 8 + 0 192 2,3 3500 16,5 221,8 A-DQ(BN)2Y GGT 18x24E9/125 24 18 + 0 432 2,3 3500 20,5 335,4 Stranded loose tube cable for outdoor applications. Highly rodent protected by 2 layers of glass rovings. This cable is used as higher fiber count data cable in distribution networks and withstands environments with high mechanical demands. Fibers according ITU-T G.652.D Construction FRP-central element loose tubes, SZ-cabling (if necessary with fillers) dry filled cable core strength members (glass-rovings) ripcord PE-sheath, UV-resistant, black with two orange longitudinal stripes Fiber colours 1-12: red, green, yellow, blue, white, violet, orange, black, grey, brown, pink, turquoise 13-24: red, green, yellow, blue, white, violet, orange, transparent, grey, brown, pink, turquoise -each with black rings every 50 mm (max.) Tube colours 1: red 2: green others: nature or white Filler colours black Laying usable for fixed laying in ducts or conduits and outdoors Marking double-sinus, phone-sign, meter marking, PENGG KABEL, year of manufacturing Technical Data tensile strength: compressive strength: impact strength: torsion: kink, cable: kink, loose tube: min. bending radius: temperature range: water penetration: according to IEC 60794-1-E1 according to IEC 60794-1-E3 value: 3000 N/10 cm according to IEC 60794-1-E4 value: 10 Nm according to IEC 60794-1-E7 value: 5 cycles ±1 turn according to IEC 60794-1-E10 value: The cables do not form a kink when a loop is drawn together to a diameter 12 times the cable nominal diameter. according to IEC 60794-1-E16 value: The loose tubes do not kink. according to IEC 60794-1-E11 value: R = 20 x D (cable outer diameter) according to IEC 60794-1-F1 storage and transport: -40 C up to +70 C laying: -5 C up to +60 C operation: -30 C up to +70 C according to IEC 60794-1-F5 value: No water on free end.

A-DQ(ZN)2Y Mini T - Mini cable, loose tube construction, D15-S05 outdoor cable metal-free longitudinally water-tight A-DQ(ZN)2Y Mini T 2x12E9/125 blue Art. No. 2035144 A-DQ(ZN)2Y Mini T 4x12E9/125 red Art. No. 2035145 A-DQ(ZN)2Y Mini T 6x12E9/125 violet Art. No. 2035146 A-DQ(ZN)2Y Mini T 8x12E9/125 pink Art. No. 2035147 A-DQ(ZN)2Y Mini T 12x12E9/125 grey Art. No. 2035148 Type number of number of tubes tube-ø tensile strength outer-ø weight fibers + fillers approx. mm max. N approx. mm approx. kg/km A-DQ(ZN)2Y Mini T 2x12E9/125 blue 24 2 + 4 1,5 700 5,6 29,1 A-DQ(ZN)2Y Mini T 4x12E9/125 red 48 4 + 2 1,5 700 5,6 30,0 A-DQ(ZN)2Y Mini T 6x12E9/125 violet 72 6 + 0 1,5 700 5,6 30,8 A-DQ(ZN)2Y Mini T 8x12E9/125 pink 96 8 + 0 1,5 700 6,5 44,5 A-DQ(ZN)2Y Mini T 12x12E9/125 grey 144 12 + 0 1,5 700 8,5 64,1 Stranded mini tube cable for laying into micro ducts. This cable is used in access networks as both connection between fiber distributers and house connection for multi dwelling units. Fibers according ITU-T G.657.A1. Due to both the deployed fibers and its light construction it is suitable for small bending radii. Construction central member, metal free loose buffer tube filled with a thixotropic gel, swellable aramid yarns dry filled cable core rip cord PE-sheath Fiber colours 1-12: red, green, yellow, blue, white, violet, orange, black, grey, brown, pink, turquoise Tube colours 1: red 2: green others: nature or white Filler colours black Marking double-sinus, phone-sign, meter marking, PENGG KABEL, year of manufacturing Technical Data tensile strength: according to IEC 60794-1-E1 compressive strength: according to IEC 60794-1-E3 value: 1000 N/10 cm impact strength: according to IEC 60794-1-E4 value: 5 Nm (3 impacts, 300 mm hammer radius) min. bending radius: according to IEC 60794-1-E11 values: static R = 10 x D, dynamic R = 20 x D (cable outer diameter) temperature range: according to IEC 60794-1-F1 storage and transport -30 C up to +60 C laying -5 C up to +50 C operation -30 C up to +60 C water penetration: according to IEC 60794-1-F5 value: 1 m (0,1 bar, 24 h) OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 9

A-DQ(ZN)2Y Mini CT - Mini cable, central unitube, D30-S04 outdoor cable metal-free longitudinally water-tight A-DQ(ZN)2Y Mini CT 12E9/125 yellow Art. No. 2035142 A-DQ(ZN)2Y Mini CT 24E9/125 blue Art. No. 2035143 Type number of number of tube-ø Zugfestigkeit outer-ø weight fibers/tube fibers approx. mm max. N approx. mm approx. kg/km A-DQ(ZN)2Y Mini CT 12E9/125 yellow 12 12 3,0 400 3,9 12,9 A-DQ(ZN)2Y Mini CT 24E9/125 blue 24 24 3,0 400 3,9 13,8 Central mini tube cable for laying into micro ducts. This cable is used in access networks as drop cable to house connections. Fibers according ITU-T G.657.A1. Due to both the deployed fibers and its light construction it is suitable for small bending radii. Construction center unitube strength members (aramide yarns) PE-sheath Fiber colours 1-12: red, green, yellow, blue, white, violet, orange, black, grey, brown, pink, turquoise 13-24: red, green, yellow, blue, white, violet, orange, transparent, grey, brown, pink, turquoise -each with black rings every 50 mm (max.) Tube colour red Marking double-sinus, phone-sign, meter marking, PENGG KABEL, year of manufacturing Technical Data tensile strength: compressive strength: impact strength: min. bending radius: temperature range: according to IEC 60794-1-E1 according to IEC 60794-1-E3 value: 1000 N/10 cm according to IEC 60794-1-E4 value: 1 Nm (3 impacts, 300 mm Hammer radius) according to IEC 60794-1-E11 value: static R = 20 x D (cable outer diameter) according to IEC 60794-1-F1 storage and transport -30 C up to +70 C laying -5 C up to +50 C operation -20 C up to +70 C

I-VQ(ZN)H 4E9/125 FTTH-Inhouse cable - Inhouse cable, V06 inhouse cable metal-free halogenfree, flame retardant I-VQ(ZN)H 4E9/125 FTTH-Inhouse cable Art. No. 2035149 Type number of tube-ø number of tubes tensile strength *) outer-ø weight fibers approx. µm + fillers max. N approx. mm approx. kg/km I-VQ(ZN)H 4E9/125 FTTH-Inhouse cable 4 600 4 + 0 400 2.8 7,5 *) with reversible attenuation increase FTTH in-house cable, suitable for laying within buildings in both horizontal and vertical ways. This cable is suitable for direct assembling with connectors. Fibers according ITU-T G.657.A1. Construction 4 buffered fibers (silikon-coated, 600 microns) strength members (aramide yarns) FRNC-sheath according to IEC 60332-3, UV-resistant Fiber colours red, green, yellow, blue Mantelfarbe grey Marking letter symbol of fiber type, meter marking, PENGG KABEL, year of manufacturing Technical Data standard: IEC 60794 tensile strength: according to IEC 60794-1-E1 compressive strength: according to IEC 60794-1-E3 value: 500 N/10 cm bending radius: static 15 x cable outer diameter dynamic 20 x cable outer diameter temperature range: storage and transport -25 C up to +70 C laying -5 C up to +50 C operation -5 C up to +50 C OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 11

Fiber optic enclosure SEC15 for max. 128 splices Description The SEC15 dome enclosure is particularly suitable for connecting fibre optic cables featuring a small number of fibres Enclosure for in-line connections and branch-offs Suitable for underground, duct, wall and pole/tower mounting Suitable for uncut cables Assembly/disassembly of the dome without any tools Sealings can be used again Separate strain relief points for central strength member and Kevlar reinforcement Storage of cut/uncut multi-fibre loose tubes Cable entries for max. 1 oval entry for 2x10-25 mm cables 3 entries for 10-20 mm cables Splice cassettes (order separate) 8 x SK120S Degree of protection >IP68 Max. splice capacity Splice protection tube 128 Tests according to DIN 47624 Draft 4/97 Mechanical strength Load (15 min) 1000 N at the centre of the enclosure, contact area 5 cm 2 Impact (once) 1 kg Steel ball, 2 m fall, at the centre of the enclosure Pressure resistance Permanent pressure 0.4 bar above atmospheric Tight from -40 C to +70C Tightness with cable Strain (15 min) 1000 N Shearing/bending (twice) Deflection 45 or a max. of 500 N bending force, Point of application 250 mm from cable entry Torsion (twice) ±90 rotation angle or a max. torque of 50 Nm, Point of application 500 mm from cable entry Vibration 168 hours; both cable ends fastened, Amplitude ±3 mm, frequency 10 Hz Temperature changes -40 C to +70 C, 10 times Immersion in wetting agent 168 hours External pressure resistance 4 m water column Water vapour permeation <240 µg/h at 10 C Material Base plate, dome, locking ring and snap-in lock Environmentally friendly, UV-resistant polypropylene Strain relief angle Stainless steel Cassette support Powder-coated aluminium sheet, RAL 7035 Weight approx. 2 kg Scope of delivery Base plate, dome, locking ring incl. snap-in lock, securing pin, sealing ring, cassette support, drying agent, instruction for installation SEC15 for max. 128 splices Art. No. 2735173

SEC23 Tubeless short for max. 288 / 432 splices Description Tubeless version suitable especially for Single Circuit (SC) and Single Element (SE). Single Circuit: Distribution of the fibres from one multi-fibre loose tube to several splice cassettes through fibre guiding channels Tubeless laying of the fibres from entry to splice cassette In-line connection and branch-off enclosure Suitable for ground, duct, wall, pole and tower mounting Short version especially for manholes or cable ducts Suitable for uncut cables Assembly/disassembly of the dome without any tools Sealings can be used again Separate strain relief points for central strength member and Kevlar reinforcement An entry module permits fibre guidance to any desired cassette entry Cable entries for max. 1 oval entry for 2x10-25 mm cables 4 entries for 10-20 mm cables 2 entries for 10-25 mm cables Splice cassettes (order separate) 36 x SK123 (SE) or SK223 (SC) Available in cassette sets of 6 splice cassettes each max. 6 sets (3 units on either side). Splice cassettes engaged in a slanted position Pivoting splice cassettes (90 ) to provide easy access to each splice Degree of protection >IP68 Max. splice capacity 2x4 splices at each SK223 (SC) 288 12 splices at each SK123 (SE) 432 Tests according to DIN 47624 Draft 4/97 Mechanical strength Load (15 min) 1000 N at centre of the enclosure, contact area 5 cm 2 Impact (once) 1 kg steel ball, 2 m fall, centre of the enclosure Pressure resistance Permanent pressure 0.4 bar above atmospheric Tight from -40 C to +70C Tightness with cable Strain (15 min) 1000 N Shearing/bending (twice) Deflection 45 or a max. of 500 N bending force, Point of application 250 mm from cable entry Torsion (twice) ±90 rotation angle or a max. torque of 50 Nm, Point of application 500 mm from cable entry Vibration 168 hours; both cable ends fastened, Amplitude ±3 mm, frequency 10 Hz Temperature changes -40 C to +70 C, 10 times Immersion in wetting agent 168 hours External pressure resistance 4 m water column Water vapour permeation <600 µg/h at 10 C Material Base plate, dome, locking ring and snap-in lock Environmentally friendly, UV-resistant polypropylene Strain relief angle Stainless steel Cassette support Powder-coated aluminium sheet, RAL 7035 Weight approx. 3.5 kg Scope of delivery Base plate, dome, locking ring with snap-in lock, securing pin, sealing ring, cassette support, drying agent, instruction for installation, 2 entry modules incl. cover SEC23 Tubeless short for max. 288 / 432 splices Art. No. 2735174 OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 13

SEC23 Tubeless classic for max. 576 / 864 splices Description Tubeless version suitable especially for Single Circuit (SC) and Single Element (SE). Single Circuit: Distribution of the fibres from one multi-fibre loose tube to several splice cassettes through fibre guiding channels Tubeless laying of the fibres from entry to splice cassette In-line connection and branch-off enclosure Suitable for ground, duct, wall, pole and tower mounting Suitable for uncut cables Assembly/disassembly of the dome without any tools Sealings can be used again Separate strain relief points for central strength member and Kevlar reinforcement An entry module permits fibre guidance to any desired cassette entry Cable entries for max. 1 oval entry for 2x10-25 mm cables 4 entries for 10-20 mm cables 2 entries for 10-25 mm cables Splice cassettes (order separate) 72 x SK123 (SE) or SK223 (SC) Available in cassette sets of 6 splice cassettes each ½ max. 12 sets (6 units on either side). Splice cassettes engaged in a slanted position Pivoting splice cassettes (90 ) to provide easy access to each splice Degree of protection >IP68 Max. splice capacity 2x4 splices at each SK223 (SC) 576 12 splices at each SK123 (SE) 864 Tests according to DIN 47624 Draft 4/97 Mechanical strength Load (15 min) 1000 N at centre of the enclosure, contact area 5 cm 2 Impact (once) 1 kg steel ball, 2 m fall, centre of the enclosure Pressure resistance Permanent pressure 0.4 bar above atmospheric Tight from -40 C to +70C Tightness with cable Strain (15 min) 1000 N Shearing/bending (twice) Deflection 45 or a max. of 500 N bending force, Point of application 250 mm from cable entry Torsion (twice) ±90 rotation angle or a max. torque of 50 Nm, Point of application 500 mm from cable entry Vibration 168 hours; both cable ends fastened, Amplitude ±3 mm, frequency 10 Hz Temperature changes -40 C to +70 C, 10 times Immersion in wetting agent 168 hours External pressure resistance 4 m water column Water vapour permeation <600 µg/h at 10 C Material Base plate, dome, locking ring and snap-in lock Environmentally friendly, UV-resistant polypropylene Strain relief angle Stainless steel Cassette support Powder-coated aluminium sheet, RAL 7035 Weight approx. 4 kg Scope of delivery Base plate, dome, locking ring with snap-in lock, securing pin, sealing ring, cassette support, drying agent, instruction for installation, 2 entry modules incl. cover SEC23 Tubeless classic for max. 576 / 864 splices Art. No. 2735175

Fiber optic enclosures - accessories Cable entry sets (shrinking) Sealing set for standard connection bushes of the SEC 15 and SEC 23 versions For sealing cables with a PE-jacket Excellent tightness and mechanical strength Material: Cross-linked polyolefine, inside coated with thermoplastic adhesive Scope of delivery: Heat-shrinkable sleeve, emery cloth, cable cleaning cloth, cable tie wraps, installation material; 1 additional branch-off clamp coming with the oval cable entry set Oval cable entry set 2x10-20 mm Art. No. 2735176 Round cable entry set 10-20 mm Art. No. 2735177 Round cable entry set 10-25 mm Art. No. 2735178 Microtube entries As an alternative to the shrinking entries there are microduct launches 16/12 mm 14/10 mm, 12/8 mm available on request. Microtube entries on request Splice cassette SK120 á 16 splices Stripping dimensions (cm): Windings Min. Max. 1.5 59 68 2 76 86 2.5 89 105 3 108 125 3.5 124 144 With the possibility for mounting the hinge: Splice storage for all kinds of optical fibres Splice cassettes can be piled one on top of the other With or without the possibility for mounting the hinge Installation of different splice protection holders is possible through the snap-on system Laying in an 8-shaped loop is possible Bending radius: >30 mm Capacity Splices 16 splice protection tubes Ø 2.5 mm (heat-shrinkable) Splice protection holders 2x...-SRH8 Reserve fibre length approx. 40 m Material: Polystyrene Weight: 36 g Scope of delivery: 1 Splice cassette (excl. splice protection holder, excl. hinge) Without the possibility for mounting the hinge: Splice cassette SK120 á 16 splices Art. No. 2735179 OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 15

Splice cassette set SK123 6xSE á 12 splices The splice cassette set serves for guiding fibres from the entry module to the splice cassette and for splice storage of all kinds of optical fibres Installation of max. 6 splice cassette sets in the SEC23 Tubeless short enclosure and max. 12 splice cassette sets in the SEC23 Tubeless classic enclosure Cassette base plate with guiding channels for fibres and fastening options for a max. of 6 splice cassettes LWL-SK123 (SE) Versions for heat-shrinkable (splice protection tubes) Material: Polycarbonate VL94HB, colour RAL 9001 Weight: 0,3 kg Scope of delivery: 1 cassette base plate, 6 LWL-SK123 splice cassettes Splice cassette set SK123 6xSE á 12 splices Art. No. 2735180 Splice cassette set SK223 6xSC á 2x4 splices The splice cassette set serves for guiding fibres from the entry module to the splice cassette and for splice storage of all kinds of optical fibres Installation of max. 6 splice cassette sets in the SEC23 Tubeless short enclosure and max. 12 splice cassette sets in the SEC23 Tubeless classic enclosure Cassette base plate with guiding channels for fibres and fastening options for a max. of 6 splice cassettes LWL-SK223 (SC) Versions for heat-shrinkable (splice protection tubes) Material: Polycarbonate VL94HB, colour RAL 9001 Weight: 0,47 kg Scope of delivery: 1 cassette base plate, 6 LWL-SK223 splice cassettes Splice cassette set SK223 6xSC á 2x4 splices Art. No. 2735181 Wall-mounting set for SEC15, SEC23 Fastening angle for convenient wall-mounting Material: Powder-coated 3-mm aluminium sheet, RAL 7035 Scope of delivery: Wall-mounting set SEC23 SEC15 SEC23 Short Wall-mounting set for SEC 15 Art. No. 2735182 Wall-mounting set for SEC 23 Art. No. 2735183

Outdoor cabinet KVZ F5 1080/320 OPDISYS Technical characteristics: Material housing and base polycarbonate Color housing and base RAL 7038 Protection class IP54 Capacity of fiber modules 16 OPDISYS Modules (16HU) at a housing size (WxHxD) 998 x 754 x 310 Gas blocker permanently integrated Door with swivel handle, prepared for two half profile cylinder Fiber optic fixing kit made of stainless steel KVZ F5 1080/320 OPDISYS Art. No. 2735184 Fiber module 24 LC/APC, 1HU Art. No. 2535159 Fiber module 24 E2000/APC, 1HU Art. No. 2535160 Fiber module 12 SC/APC, 1HU Art. No. 2535161 Fiber module for up to 48 splices, 1HU Art. No. 2535162 KVZ small as splicing version - equipped with 2x6 splice cassettes sets of SEC23 on request OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 17

Cable manhole EK 428 LW 800x1400 Low weight An advantage when transporting and handling. Easy delivery to inaccessible sites, such as along railway lines or inner-city areas Minimal installation effort No heavy transporters or cranes required Modular construction Manhole depths and connection positions are variable by means of the combination of framework modules Superstructure about existing pipe extrusion lines Without any difficulty bonding of existing pipeline alignment through open side parts in connection with the accessory Through the low weight the bonding is acutely easy Practical product Infinitely variable height and angle compensation Exact-fit pipe connections by means of set break points Sealing elements for cables without tubing Stability High degree of stability with low inherent weight, resulting from the use of high-quality plastic Optimum embedding in the surrounding soil Mechanical protection of the top edge provided by hot-dip galvanised steel frame Material For all load-bearing elements made of plastic: Modified polycarbonate (PC) High temperature resistance Surface finish not critical affected by hot or melted asphalt High degree of stability Fireproof Corrosion-proof Highly resistant to chemicals Highly resistant to UV light and weathering Recyclable several times over

Fittings Up to 2 sleeves (SEC15 or SEC23) for direct buried fiber optic cables or micro tubes with swiveling telescopic sleeve holder for a optimum working position Manhole cover Manhole cover in various versions: Cast iron (with lock) - D400 (400 kn testing force) Steel filled with concrete (with lock) - D400 (400 kn testing force) Bulb plate (with screwed) - A15 (15 kn testing force) Accessories Under cover fuse for protection against damage to the fittings Monitoring system for central monitoring of access Dimensions and test classes clear dimension: 800 x 1400 mm External height: 935 mm Test class: D400 and A15 EK 428 LW 800x1400 with cast iron cover (consisting of 4 parts) Art. No. 2735185 EK 428 LW 800x1400 with bulb plate cover (consisting of 3 parts) Art. No. 2735186 EK 428 LW 800x1400 with steel cover on request Telescopic sleeve holder Art. No. 2735187 Other manhole types on request OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 19

House lead-in EK 459 for micro-tubes, gas-tight This house lead is specially designed for the sealing of fiber optic cable in the introduction in building walls. It is suitable for all wall types (DIN 1819T.4) as suitable for foundations made of waterproof concrete. The foaming principle guarantees a perfect seal. Technical characteristics: Required bore diameter of only 40 mm Cover a large range of diameters of m micro-tubes: 7-14 mm single introduction and 7 mm double insertion Wall thickness: 400 mm standard, others upon request Delivery option for micro-tube diameters from 2 to 8 mm Gas-tight and waterproof up to 4 m water column Due to funnel-shaped silicone sealing discs technology only minimum effort pushing in the micro-tube / fiber optic cable, therefore no risk of kinking the line About quick-grid-screw flange permanent pressing of the plastic sealing bead (outside of building) Fast and gentle on the material sealing the micro-tubes / fiber optic cables EK 459 for micro-tubes, gas-tight, for wall thicknesses up to 400 mm Art. No. 2735214 Other house lead-in on request

Microtube Micro tubes are made of high density polyethylene (HDPE) and Silicore (super smooth inner surface, co-extruded with HDPE, allows higher injection and retraction speeds and lengths) were prepared and used to protect optical fiber cable. Inner surface is made from permanent sliding material Silicore with a very low coefficient of friction and standardly with fine ribs. Outer microduct s surface is smooth. Microduct is not designed for permanent inner pressure. Microduct does not contain dangerous chemicals in accordance to the Directive 2006/1907/EC (REACH). Microduct meets requirements of the Directive 2002/95/EC (RoHS) - content of lead, cadmium, mercury, Cr VI, PBB und PBDE. General specification Parameter Value Standard, conditions Ovality max. 5% Internal standard, before coiling Inner coefficient of friction max. 0,1 Internal standard Visual examination free from defects Internal standard Crush - pressure force min. 1000 N EN 60794-1-2, E3, sample 200 mm, aktive 100 mm, ID deformation by 15%, speed 3 mm/min. Impact no damage after the test, dimens. in tolerances after recovery EN 60794-1-2, method E4, striking surface radius 10 mm, impact energy 15 J, recovery time 1 h Thermal expansion 1,6.10-4 K 1 ISO 11359-2, temperature range from -20 C to +70 C Longitudinal reversion max. 3% EN ISO 2505, oven, 110 C, 60 min. Transport and storage temperatures from -40 C to +70 C - Installation temperatures from -10 C to +50 C - Operating temperatures from -40 C to +70 C - Blowing pressure max. 20 bar max. 2 hours at max. +50 C Outdoor exposure (central eurpope conditions) max. 12 months - Microduct DB 7/4 - recommended cable outer diameter from 1,0 to 2,5 mm Parameter Value Standard, conditions Outer diameter (OD) 7±0,1 mm Internal standard Inner diameter (ID) min. 3,9 mm Internal standard Wall thickness (WT) min. 1,4 mm Internal standard Blown ball test (BB-test) pass Internal standard, ball diameter 3,5 mm Burst pressure min. 70 bar EN ISO 1167-1, 2 Crush - residual deformation max. 15% OD = max. 1,1 mm EN 60794-1-2, E3, sample 200 mm, aktive 100 mm, force 1718 N, 3 mm/min., aktion 60 s, recovery 20 s Bending stiffness min. 0,04 N.m 2 Internal standard Standard Dimension Ratio (SDR = OD/WT) 4,7 - Weight 25 kg/km - Installation tensile force max. 350 N - Minimum bending 70 mm - OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 21

Microduct DB 10/6 - recommended cable outer diameter from 2,0 to 4,5 mm Parameter Value Standard, conditions Outer diameter (OD) 10±0,1 mm Internal standard Inner diameter (ID) min. 5,9 mm Internal standard Wall thickness (WT) min. 1,9 mm Internal standard Blown ball test (BB-test) pass Internal standard, ball diameter 5,0 mm Burst pressure min. 70 bar EN ISO 1167-1, 2 Crush - residual deformation max. 15% OD = max. 1,5 mm EN 60794-1-2, E3, sample 200 mm, aktive 100 mm, force 2100 N, 3 mm/min., aktion 60 s, recovery 20 s Bending stiffness min. 0,19 N.m 2 Internal standard Standard Dimension Ratio (SDR = OD/WT) 5 - Weight 47,5 kg/km - Installation tensile force max. 680 N - Minimum bending 100 mm - Microduct DB 12/8 - recommended cable outer diameter from 4,0 to 6,5 mm Parameter Value Standard, conditions Outer diameter (OD) 12±0,1 mm Internal standard Inner diameter (ID) min. 7,9 mm Internal standard Wall thickness (WT) min. 1,9 mm Internal standard Blown ball test (BB-test) pass Internal standard, ball diameter 6,5 mm Burst pressure min. 60 bar EN ISO 1167-1, 2 Crush - residual deformation max. 15% OD = max. 1,8 mm EN 60794-1-2, E3, sample 200 mm, aktive 100 mm, force 1680 N, 3 mm/min., aktion 60 s, recovery 20 s Bending stiffness min. 0,36 N.m 2 Internal standard Standard Dimension Ratio (SDR = OD/WT) 6 - Weight 59 kg/km - Installation tensile force max. 840 N - Minimum bending 120 mm - Microduct DB 14/10 - recommended cable outer diameter from 5,0 to 8,5 mm Parameter Value Standard, conditions Outer diameter (OD) 14±0,1 mm Internal standard Inner diameter (ID) min. 9,9 mm Internal standard Wall thickness (WT) min. 1,9 mm Internal standard Blown ball test (BB-test) pass Internal standard, ball diameter 8,0 mm Burst pressure min. 50 bar EN ISO 1167-1, 2 Crush - residual deformation max. 15% OD = max. 2,1 mm EN 60794-1-2, E3, sample 200 mm, aktive 100 mm, force 1400 N, 3 mm/min., aktion 60 s, recovery 20 s Bending stiffness min. 0,61 N.m 2 Internal standard Standard Dimension Ratio (SDR = OD/WT) 7 - Weight 72 kg/km - Installation tensile force max. 1010 N - Minimum bending 140 mm - Microduct DB 16/12 - recommended cable outer diameter from 7,0 to 10,0 mm Parameter Value Standard, conditions Outer diameter (OD) 16±0,1 mm Internal standard Inner diameter (ID) min. 11,9 mm Internal standard Wall thickness (WT) min. 1,9 mm Internal standard Blown ball test (BB-test) pass Internal standard, ball diameter 10,0 mm Burst pressure min. 40 bar EN ISO 1167-1, 2 Crush - residual deformation max. 15% OD = max. 2,4 mm EN 60794-1-2, E3, sample 200 mm, aktive 100 mm, force 1200 N, 3 mm/min., aktion 60 s, recovery 20 s Bending stiffness min. 0,94 N.m 2 Internal standard Standard Dimension Ratio (SDR = OD/WT) 8 - Weight 84 kg/km - Installation tensile force max. 1150 N - Minimum bending 160 mm - Microduct 7/4 (for cables from 1,0-2,5 mm) Art. No. 2735188 Microduct 10/6 (for cables from 2,0-4,5 mm) Art. No. 2735189 Microduct 12/8 (for cables from 4,0-6,5 mm) Art. No. 2735190 Microduct 14/10 (for cables from 5,0-8,5 mm) Art. No. 2735191 Microduct 16/12 (for cables from 7,0-10,0 mm) Art. No. 2735192

Metal free micro duct connector Body material: Polyamide Spring material: Polyacetal Seal material: NBR Temperature range: -20 C to +50 C Working pressure: max. 20 bar Lifespan: 25 years Standards: EN 50441-2-8 Available sizes (Dimension length / width / through bore / tensile force [N]) Connector for microducts 7/3.5 mm 42 / 17 / 3.5 / 150 N Connector for microducts 10/5.5 mm 48 / 20.5 / 5.5 / 250 N Connector for microducts 12/8 mm 52 / 23 / 8.0 / 530 N Connector for microducts 14/10 mm 60 / 25.5 / 10.0 / 1000 N Connector for microducts 16/12 mm 67 / 30 /12.0 / 1500 N Metal free micro duct connector 7 mm Art. No. 2735193 Metal free micro duct connector 10 mm Art. No. 2735194 Metal free micro duct connector 12 mm Art. No. 2735195 Metal free micro duct connector 14 mm Art. No. 2735196 Metal free micro duct connector 16 mm Art. No. 2735197 Metal free end stop Body material: Polyamide Spring material: Polyacetal Seal material: NBR Temperature range: -20 C to +50 C Impact resistance: 1000-4000 N Working pressure: max. 20 bar Lifespan: 25 years Standards: EN 50441-2-8 Available sizes (Dimension length / width / tensile force [N]) End stop for 7 mm microducts 23 / 17.0 / 80 N End stop for 10 mm microducts 26 / 20.5 / 150 N End stop for 12 mm microducts 28 / 23.0 / 200 N End stop for 14 mm microducts 33 / 25.5 / 300 N End stop for 16 mm microducts 36.5 / 30.0 / 400N Metal free micro duct end stop 7 mm Art. No. 2735198 Metal free micro duct end stop 10 mm Art. No. 2735199 Metal free micro duct end stop 12 mm Art. No. 2735200 Metal free micro duct end stop 14 mm Art. No. 2735201 Metal free micro duct end stop 16 mm Art. No. 2735202 Divisible gasblock Body material: Seal material: Gas seal pressure: reinforced glassfiber polyamid TPE 0,5 bar Divisible gasblock 7 (for 2,5 mm cables) Divisible gasblock 10 (for cables from 2,5-3,9 mm) Divisible gasblock 12 (for cables from 5,6-6,5 mm) Divisible gasblock 14 (for 8,5 mm cable) Divisible gasblock 16 (for 8,5 mm cable) Art. No. 2735203 Art. No. 2735204 Art. No. 2735205 Art. No. 2735206 Art. No. 2735207 Microduct cutter and deburring tool For clean and safe construction of the microduct network, we recommend that you use the appropriate tools: Microduct cutter 4-12 mm Microduct shear 4-28 mm Deburring tool Microduct shear 4-28 mm Art. No. 2735208 Microduct cutter 4-12 mm Art. No. 2735209 Deburring tool Art. No. 2735210 OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 23

Interconnect case OM10 BEP The distribution enclosure serves as a termination for fiber optic cable to connector and for storing from splicing for max. 8 customers fibers (1 household) Small termination box, especially suitable where space is limited Suitable for indoor wall-mounting and installation in moist rooms Pull-out splice storage frame with splice protection holders Installation point for strain relief element (Kevlar) Provides sufficient space for multi-fibre loose tube reserves under the splice storage frame Entries Multi entry for 3 x I-VQ(ZN)H cable and PG9 cable gland Splice protection holder 1 SRH8 or 1 SWH12 Degree of protection of the empty enclosure IP54 Material Enclosure Polystyrene, similar to RAL 7035 Splice storage frame Powder-coated aluminium, RAL 7035 PG Cable entry gland Plastic Weight Approx. 0.7 kg Scope of delivery 1 Enclosure, 1 splice storage frame, 1 copy of Instructions for Installation, 1 PG9-cable gland, 2 cable tie wraps, 2 pigtail clips PC121, 1 SRH8/SWH12 splice protection holder OM10 BEP for max. 8 customer fibers (1 household), incl. 1 Stk. splice storage frame Art. No. 2735211

RGV20 BEP The interconnect case RGV 20 BEP is used for distribution of the fibers in multiple dwellings to the specific house cabling for max. 96 customer fibers. The tubeless version is particularly suitable for Single Circuit (SC) and Single Element (SE) Single Circuit: Distribution of the fibres from one multi-fibre loose tube to several splice cassettes through fibre guiding channels Single Element: For multi-fibre loose tube management (multi-fibre loose tube upon multi-fibre loose tube) Tubeless laying of fibres from the entry to the splice cassette Enclosure for in-line connections and branch-offs Suitable for wall mounting Door is right-hinged and easy to remove Clip-down handle Door sealing inside Degree of protection IP 54 with PG cable entry Strain relief points for central strength member and Kevlar reinforcement Storage area for cut/uncut multi-fibre loose tubes The removable cassette-ground plate is used for fastening the multi-fibre loose tubes and also for assembling the splice cassette sets onto the mounting plate The entry module permits fibre routing to any cassette entry Cable entries PG cable entries Ø 8-10 mm (PG11) Ø 10-12 mm (PG13) Ø 12-14 mm (PG16) Ø 14-17 mm (PG21) 24x Ø 3 mm (PG29) for I-VQ(ZN)H 12 x SK123 (SE) or SK223 (SC) Splice cassettes Available as sets of 6 splice cassettes each => max. 2 sets Splice cassettes are engaged in a slanted position Swing-type splice cassettes (90 ) provide easy access to each splice Permanent temperature Max. 150 C Material Enclosure Thermoformed, self-extinguishing, halogen-free, glass-fibre reinforced polyester, colour RAL 7035 Mounting-, Base plate Powder-coated sheet steel, RAL 7035 Patch-, Fastening angle Powder-coated sheet steel, RAL 7011 Weight Approx. 5,1 kg Scope of delivery 1 Cabinet incl. door, clip-down handle and sealing, 1 mounting plate, 1 base plate, 1 entry module with cover, 1 fastening angle, 1 Angle with holes, fastening screws 415 A 315 B 175 C RGV20 BEP basic casing empty Art. No. 2736264 RGV20 BEP for max. 48 customer fibers (11 households), incl. 1 splice cassettes set (see page 16) RGV20 BEP for max. 96 customer fibers (23 households), incl. 2 splice cassettes sets (see page 16) Art. No. 2736265 Art. No. 2735212 OTO ZT 2xLC/APC Fiber optic junction box for FTTH-inhouse cabling For surface wall mounting FTTH junction box for 1 to 4 fibers Consists of a metal mounting plate, a plastic housing with integrated fiber storage for cable and pigtail wires and integrated in the housing Shuttered 2x LC / APC adapters including pigtails Adapters with integrated laser protection Labeling field with transparent cover Color: white, similar to RAL 9010 Dimensions: 88x88x23 mm OTO ZT 2xLC/APC pigtails inserted - ready for splicing Art. No. 2535213 OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 25

Heat shrinkable fiber optic splice protector Outer shrink tube: transparent, both ends preshrunk to closing the gap between the two tubes Inner shrink tube: transparent EVA hot melt adhesive (Ethylene vinyl acetate) Stainless steel with rounded ends to avoid fiber damage Color transparent Operating temperature -45 C to +100 C Shrink temperature 110 C Tensile strength 18 MPa (acc. ASTM D2671) Ultimate elongation 700 % (acc. ASTM D2671) Density 0,94 g/cm3 (acc. ISO R1183D) Dielectric strength 25 kv/mm (acc. IEC 243) Dielectric constant 2,5 (acc. IEC 243) Longitudinal change ±5 % (acc. ASTM D2671) Marking Pengg_MM.JJJJ Type Outer shrink tube (shrunk) outer-ø D1 length L1 Inner shrink tube (unshrunk) outer-ø D2 length L2 pin-ø D3 Steel pin stainless length L3 SP/F25/2,5A 2,45 ±0,1mm 25 ±0,5mm 1,3 ±0,3mm 25 ±0,5mm 1,0 ±0,05mm 21 ±0,1mm SP/F45/2,5A 2,45 ±0,1mm 45 ±0,5mm 1,3 ±0,3mm 45 ±0,5mm 1,0 ±0,05mm 41 ±0,1mm Heat shrinkable fiber optic splice protector SP/F25/2,5A Heat shrinkable fiber optic splice protector SP/F45/2,5A Art. No. 2735457 Art. No. 2735456 Adapter LC/APC 8 duplex flange with shutter Adapter with flange or snap-on mounting with shutter Adapter LCdx/APC 8 duplex flange with shutter Art. No. 2736272 19 Fiber optic patch panel Designed to storage fiber optic cables and splicing cassettes Intended for installing in 19 rack system Enable fiber optic termination and distribution Model offered: Resetable and sliding Installation depth: 250 mm Material: steel Powder coated Colour: RAL 7035 (Light Grey) - other colours on request Universal splice cassette holding system: fixed & booklet mounting option Equipped with removable splice cassette holder and antitwist system By default with 1 or 6 duplex adapters and pigtails 19 Fiber optic patch panel 24/1LCdx/APC 8 SM 1xPG16/1xAB RAL7035 complete Art. No. 2536273 19 Fiber optic patch panel 24/6LCdx/APC 8 SM 1xPG16/1xAB RAL7035 complete Art. No. 2536274

Fiber-Pigtail Pigtails with optical fiber (600 µm acrylate buffer) and LC/APC8 connector Description of LC/APC simplex: user-friendly audible latch to indicate proper mating push-pull locking plastic housing with zirconia ferrule standard IEC 61754-20 insertion loss (IL) for SM (typical) mean value < 0.15 db (to reference connector) max. value < 0.30 db (to reference connector) return loss (RL) > 65 db 8 SM-Angle (APC) polishing PT LC/APC8 1E9/125/600/rt 1m for OTO Art. No. 2536266 PT LC/APC8 1E9/125/600/gn 1m for OTO Art. No. 2536267 PT LC/APC8 1E9/125/600/ge 1m for OTO Art. No. 2536268 PT LC/APC8 1E9/125/600/bl 1m for OTO Art. No. 2536269 PT LC/APC8 1E9/125/600/rt 2m for patch panel Art. No. 2536275 PT LC/APC8 1E9/125/600/gn 2m for patch panel Art. No. 2536276 PT LC/APC8 1E9/125/600/ge 2m for patch panel Art. No. 2536277 PT LC/APC8 1E9/125/600/bl 2m for patch panel Art. No. 2536278 FTTH in-house cable, installation cable on a cardboard reel I-VQ(ZN)H 4E9/125 FTTH in house cable preassembled with 2 LC/APC 8 connectors PT LC/APC8 2E9/125/600/2800 20m excl. OTO Art. No. 2536279 PT LC/APC8 2E9/125/600/2800 30m excl. OTO Art. No. 2536280 PT LC/APC8 2E9/125/600/2800 40m excl. OTO Art. No. 2536281 PT LC/APC8 2E9/125/600/2800 50m excl. OTO Art. No. 2536282 PT LC/APC8 2E9/125/600/2800 60m excl. OTO Art. No. 2536283 OPDISYS Fiber to the Home - Solution 02/2016 by Pengg Kabel GmbH Technische Änderungen vorbehalten 27

Fiber optic cables Fiber optic passive components Fiber optic installation services Fiber to the home - solutions Telecommunication cables Railway cables Copper cable installation services PENGG KABEL GmbH Plant Optic Breitenfeldgasse 5 8661 Sankt Barbara Plant Copper Mariazellerstraße 125 8605 Kapfenberg Tel.: +43 3862 / 23990-0 Fax.: +43 3862 / 23990-672 info@penggkabel.at www.penggkabel.at