Steel Pipe and Tube Section 13
13-1 INFORMATION - STEEL PIPE AND TUBE GENERAL INFORMATION Rigid hydraulic tubing offers intrinsic bene ts when installing uid transfer lines in both xed and mobile plant applications. Hydraulic tube and schedule pipe have a low I.D. to O.D. ratio, have a compact minimum bend radius, can be easily bent to required shapes, are easily clamped (even in multiple runs) and, provided adequate protection is applied, have a long service life. 12 Imperial or metric hydraulic tube supplied by Hydraulink is a cold drawn seamless annealed tube in in carbon steel or AISI 316 stainless steel qualified quali to the appropriate standards. Hydraulink can also supply pre-formed tube bends (45 and 90 as standard; other angles by request) in in standard and long-leg versions. The standard leg version is is also available in in heavy wall wall tube tube for for heavy duty applications. duty applications. Hydraulink Pressure ratings Fluid Connectors Ltd. reserves the right to discontinue, or to alter the design and speci - cation Pressures of any in the product table listed are based in this on catalogue. tubing with a tensile strength of 340MPa and were calculated in accordance with the formulae stated in the ISO 10763/SAE J1065 standards. Hydraulink Fluid Connectors Ltd. reserves the right to discontinue, or to alter the design and specification of any product listed in this catalogue. Our product range is constantly evolving and Hydraulink reserve the right to change technical specifications without notice www.hydraulink.com Copyright HYDRAULINK FLUID CONNECTORS 2010
13-2 INFORMATION - STEEL PIPE AND TUBE PART NUMBERING SYSTEM - HYDRAULIC TUBE The Hydraulink part numbering system is a concise product description in coded form. The part number consists of a minimum of two modules as follows: Module 1. Module 2: 2. Code letters ST denoting carbon steel or or SST SST denoting stainless steel steel tube. tube. STP denotes trivalent plated Carbon Steel tube. Number denoting the size of outside diameter, expressed as follows; Number denoting the size of of outside diameter, expressed as as follows: follows; Imperial tube: tube; expressed in in 1/16th inch inch increments denoting denoting the the outside outside diameter. diameter. For example: For 08 example; = 8/16 = 08 1/2 = 8/16 O.D and = 1/2 20 O.D = 20/16 and = 20 1 1/4 = 20/16 O.D. = 1 1/4 O.D. Metric Metric tube; tube: expressed expressed in in millimetres millimetres with with prefix pre M, x M, denoting denoting the the outside outside diameter. For example: M16 = 16mm O.D. diameter. For example; M16 = 16mm O.D. 12 Module Any variations 3: Number to wall thickness denoting (gauge) the wall thickness from the standardised of the steel tube product stocked by Hydraulink is denoted by a suf x. Imperial tube: expressed in wall thickness gauge. For example: 14 = 14 gauge = 2.03mm Metric tube: expressed in millimetres (with the decimal point missing). For example: 15 = 1.5mm wall thickness PART NUMBERING SYSTEM - EXAMPLE Part number: ST-2010 ST-20-10G Complete description: desription: 1 1/4 outside diameter carbon steel hydraulic line tube, with 10 gauge (3.25mm) wall thickness. ST - 20-10G Module 1. Material ST denotes carbon steel as material for hydraulic tube Suffix. 10G 10 denotes the tube has a different a wall wall thickness thickness of (10 gauge // 3.25mm) than the Hydraulink standard Module 2. Size 20 denoting 20/16 = 1 1/4 outside diameter Our product range is constantly evolving and Hydraulink reserve the right to change technical specifications without notice www.hydraulink.com Copyright HYDRAULINK FLUID CONNECTORS 2010
13-3 INFORMATION - STEEL PIPE AND TUBE PART NUMBERING SYSTEM - PRE-FORMED TUBE BENDS The Hydraulink part numbering system is a concise product description in coded form. For preformed tube bends, the part number consists of a minimum of three modules as follows: Module 1. Code letters TB denoting standard wall or TBH denoting heavy wall tube. Module 2. Number denoting tube bend angle (con guration); typically 45 or 90. 12 Module 3. Number denoting the size of outside diameter, expressed as follows; Imperial tube; expressed in 1/16th inch increments denoting the outside diameter. For example; 08 = 8/16 = 1/2 O.D and 20 = 20/16 = 1 1/4 O.D. The suf x EXT is added to the part number to describe a long leg (extended leg) bend. PART NUMBERING SYSTEM - EXAMPLE Part number: TB-90-10EXT Complete desription: 90 tube bend, 5/8 outside diameter, standard wall thickness, with one extended leg. TB - 90-10 EXT Module 1. Tube type TB for standard wall thickness tube bend Suffix. EXT denotes the bend has one extended leg Module 2. Configuration 90 denoting 90 bend angle Module 3. Tube size 10 for 10/16ths = 5/8 denotes outside diameter of tube Our product range is constantly evolving and Hydraulink reserve the right to change technical specifications without notice www.hydraulink.com Copyright HYDRAULINK FLUID CONNECTORS 2010
13-4 STEEL PIPE AND TUBE INDEX HYDRAULIC TUBE IMPERIAL HYDRAULIC TUBE STP Page 13-5 METRIC HYDRAULIC TUBE STP-M Page 13-5
13-5 STEEL PIPE AND TUBE HYDRAULIC TUBE STP IMPERIAL HYDRAULIC TUBE SEAMLESS HYDRAULIC LINE TUBE - IMPERIAL O.D. Part Number O.D - inches O.D - mm Wall thickness - Gauge Wall thickness - mm Weight - kg/m Pressure - bar Pressure - psi STP-0420 1/4 6.35 20G 0.91 0.12 310 4480 STP-0618 3/8 9.525 18G 1.22 0.25 276 4010 STP-0816 1/2 12.7 16G 1.63 0.45 277 4020 STP-1016 5/8 15.875 16G 1.63 0.57 221 3210 STP-1214 3/4 19.05 14G 2.03 0.85 230 3340 STP-1610 1 25.4 10G 3.25 1.6 255 3700 STP-1614 1 25.4 14G 2.03 1.2 198 2870 STP-2010 1.1/4 31.75 10G 3.25 2.3 221 3200 STP-2410 1.1/2 38.1 10G 3.25 2.8 184 2670 HYDRAULIC TUBE STP-M METRIC HYDRAULIC TUBE SEAMLESS HYDRAULIC LINE TUBE - METRIC O.D. Part Number O.D - mm Wall thickness - mm Weight - kg/m Pressure - bar Pressure - psi Flow - l/min STP-M1015 10 1.5 0.31 339 4916 16.7 STP-M1215 12 1.5 0.39 283 4096 21.8 STP-M1420 14 2 0.59 323 4681 34.2 STP-M1515 15 1.5 0.5 226 3277 49.2 STP-M1620 16 2 0.69 283 4096 49.2 STP-M1815 18 1.5 0.61 188 2731 76.8 STP-M2020 20 2 1.08 283 4096 76.8 STP-M2220 22 2 0.99 205 2979 111 STP-M2530 25 3 1.63 271 3932 123 STP-M810 8 1 0.2 245 3550 10.2 - Please contact Hydraulink for further details and availability. Pricing current as at 1 Jan 2018 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.
13-6 STEEL PIPE AND TUBE - Please contact Hydraulink for further details and availability. Pricing current as at 1 Jan 2018 and excludes GST. Hydraulink reserve the right to change pricing and technical specifications without notice.