Blasting Abrasives CSI supplies every type of blasting abrasive and can assist you with choosing the right product to meet your application requirements. We have warehouse facilities conveniently located in Atlanta, GA and Jacksonville, FL, and provide top notch logistics to get the abrasives you need to your job site on time and on budget. Dupont Starblast Starblast blasting abrasives are a loose blend of uniformly sized coarse and fine staurolite sands that have clean, rounded surfaces. Cleaning speed, low dust generation, and recyclability make Dupont Starblast a good choice for removal of mill scale, rust, and weathered coatings. There are five product grades available: Biasill Starblast Starblast XL Starblast Ultra Coarse Staurolite 4,000 lb. bulk bags Bulk truckloads Railcar
Garnet Garnet is a non ferrous, 100% natural inert mineral containing less than 1% free silica that poses little to no health or environmental risks. It produces less dust than other abrasives, improves operator visibility and reduces cleanup costs while minimizing the impact on adjoining work areas. Garnet delivers high performance cleaning, cuts faster and lasts longer, significantly increasing productivity while reducing abrasive consumption, handling, and collection and disposal costs. Sizes available: 36 grit 3040 grit 3060 grit 80 grit 100 grit 55 lb. bags 4400 lb. bulk bags Bulk truckload
Coal Slag Coal Slag is a non ferrous, chemically inert, blasting abrasive that features low dusting, and low free silica content. Coal slag is used for removing paint, rust, mill scale, and other contaminants from steel surfaces. Coal Slag meets or exceeds industry, military and California standards, thereby enhancing worker safety and potentially reducing costs associated with special waste handling and worker liability insurance. Meets all known industry abrasives specifications and environmental standards including SSPC AB1, MIL A 22262B(SH) and 40CFR 261.24a (TCLP) Approved by the U.S. Navy s OPL (MIL A 22282) Low dusting; passes California Title 17 (CARB) Available pre blended with Blastox Sizes Available: 1040 Utility Grade 1240 Medium Grade 2040 Fine Grade 3060 Extra Fine 100 lb. bags Bulk Bags Bulk Truckloads Bulk Railcar
Copper Slag Copper Slag is a non ferrous blasting abrasive that features low dusting, and low free silica content. Copper slag is used for removing paint, rust, mill scale, and other contaminants from steel surfaces. Meets SSPC AB1 Low dusting; passes California Title 17 (CARB) Available pre blended with Blastox Sizes Available: EG 12 Coarse EG 14 Medium EG 20 Fine 100 lb. bags Bulk Bags Bulk Truckloads
Steel Grit Cast angular grit is produced by crushing specially heat treated steel shot pellets. Its blast cleaning characteristics are dependent upon the Rockwell C hardness of the material. It is best suited to compressed air blasting applications. Rockwell C Hardness ranges available are: o GP 40/48 o GB 48/55 o GL 55/62 o GH 62/68 Sizes Available: G 12 G 14 G 16 G 18 G 25 G 40 G 50 G 80 G 120 1500 2,000 lb. drums
Steel Shot Steel shot has a spherical structure of finely tempered martensite steel to provide optimum resilience. Its durability and resistance to impact fatigue provide maximum cleaning efficiency at the most economical cost. It is best suited to shot peening applications. Sizes Available: S 70 S 110 S 170 S 230 S 280 S 330 S 390 S 460 S 550 S 660 S 780 2,000 lb. drums
Armex Armex baking soda abrasive is used to clean, de paint, and degrease metals, aluminum, other alloys, composites, and even plastics, and composites. Armex is delivered using compressed air or with a pressure washer where it is injected into the water stream. Armex is available in Standard, Premium, Profile, and Specialty Formulations to meet your application requirements. Formulas available: Standard Formulas Maintenance Formula Maintenance Formula XL Maintenance Formula with SupraKleen Maintenance Formula XL with SupraKleen Premium Formulas Flow Formula M Flow Formula XL Profile Formulas Profile XL Profile XL2+ Turbine Specialty Formulas Anilox Roll Formula Composite Formula Electronics Formula Hydro Flex Formula
Aluminum Oxide Aluminum oxide is produced by fusing bauxite and anthracite in an electric arc furnace at high temperature. Aluminum Oxide grains feature multiple sharp cutting edges, maximum resistance to breakdown, and contain no crystalline free silica making it one of the fastest, most versatile and economical cutting abrasives available, usable in both dry and wet blasting applications from cleaning and deburring to etching and finishing. CSI offers a wide range of grades to meet the particular needs of your job, from a coarse profile to a micro finish. Meets ANSI B.74 Table III Specifications Sizes Available: 16 1200 grit 400 lb. fiber drums (12 120 grit) 390 lb. fiber drums (150 240 grit)
Glass Beads Glass beads are a chemically inert, environmentally friendly abrasive that contain no free silica. They are manufactured to uniform size and hardness and used for precise blast cleaning control for peening, cleaning, finishing, and deburring. Meets Mil PRF 9954C Sizes Available: #3 20 30 US Sieve #4 30 40 US Sieve #5 40 50 US Sieve #6 50 70 US Sieve #7 60 80 US Sieve #8 80 100 US Sieve #9 80 120 US Sieve #10 100 170 US Sieve #11 120 200 US Sieve #12 140 230 US Sieve #13 170 325 US Sieve
Silicon Carbide Black Silicon Carbide is produced in electrical furnaces from high purity silica sand and petroleum coke. Its combination of being very hard and sharp makes it a very aggressive abrasive ideal for many applications. Black Silicon Carbide is typically used on hard or brittle materials. It is also used for kiln furniture, lapping and polishing, non woven, tumbling, pressure blasting, anti skid, electrical heating elements, aerospace, and composites. CSI offers a wide range of grades to meet the particular needs of your job, from a coarse profile to a micro finish. Sizes Available: 8 240 grit 300 lb. fiber drums
Plastic Media Plastic Media Blasting is a proven, environmentally friendly safe alternative to chemical strippers and other hard abrasives. Plastic media is used for a wide variety of commercial industrial applications including paint stripping, surface preparation, deflashing, deburring, mold cleaning, and contamination stripping. Plastic media is used for cleaning ferrous and non ferrous metals, composite materials, and delicate surfaces. Three (3) Primary Types are offered: Type 2 Urea Type 3 Melamine Type 5 Acrylic Sizes Available: 12/16 16/20 20/30 30/40 40/100 250-lb or 275-lb drums
Organic Blast Media CSI supplies organic blasting abrasives including Walnut Shells and Corn Cobs. These products are all natural, 100% silica free making them an environmentally abrasive for delicate blasting processes. The gentle cleaning action cleans surfaces with damaging the underlying material. Sizes Available: 6/10 through 30/100