Easy Drain TAF Side outlet INSTALLATION MANUAL FOR WOODEN OR CONCRETE SUBFLOORS
Easy Drain CONTENTS Installation options... 3 Frame options... 3 Height adjustable feet... 4 Height adjustable feet Wall mounted... 5 Installation guide No-Hub Sleeve... 6 Sealing guide... 8 Frame & Grating... 9 Installation example... 11 Installation diagram No-Hub sleeve... 12 Installation diagram - Wall No hub sleeve... 13 TAF Extension sets Wall-to-wall installation... 14 Important assembling advice... 15 2
INSTALLATION OPTIONS Against the wall Wall mounted Centered Wall-to-Wall At the entrance FRAME OPTIONS MODULO TAF (Z1) TAF WALL DESIGN (Z2) DESIGN (Z3) DESIGN (Z4) 3
Easy Drain HEIGHT ADJUSTABLE FEET 1A 1B CUT THE LEGS FOR LESS HEIGHT 2 3 4 5 4
HEIGHT ADJUSTABLE FEET WALL MOUNTED 1 2 width measure for height 3 4 5 6 87 8 SMALLEST FLANGE AT THE WALL 5
INSTALLATION GUIDE NO-HUB SLEEVE 1 2 PAN LINER WITH ADHESIVE BONDING SEAL THE ENTIRE FLOOR WITH PAN LINER REMOVE AIR POCKETS BENEATH THE LINER 3A 3B CONCRETE BOARD (AT LEAST ¼ ABOVE THE FLOOR) OPTION: CURBLESS SHOWER INSTALLATION 4A 4B WALL MOUNTED SEE PAGE 7 FOR OTHER INSTALLATION OPTIONS NO-HUB SLEEVE* NOT INCLUDED 5 6 MAKE SURE THE CONNECTION BETWEEN THE DRAIN AND DISCHARGE PIPE IS WATERTIGHT! 6 *NOTE: No-Hub Sleeve may vary depending on model being used
Easy Drain 7A CENTERED SLOPED MORTAR BED 7B WALL-to-WALL SLOPED MORTAR BED 7C WALL MOUNTED SLOPED MORTAR BED 7D WALL MOUNTED WALL-toWALL SLOPED MORTAR BED 7
SEALING GUIDE All sealing instructions are similar for every type of installation, e.g. centered, wall-to-wall etc. Only the way in which the waterproofing membrane is fitted to the walls differs between the various types of installation (see drawing on page 7). 1 FLEXIBLE SEALING COMPOUND 2A CENTERED 2B WALL MOUNTED 3 4 FLEXIBLE SEALING COMPOUND SEAL THE ENTIRE FLOOR WITH THIN-SET MEMBRANE REMOVE AIR POCKETS BENEATH THE MEMBRANE 5 OPTIONAL: FLEXIBLE SEALING COMPOUND 8
FRAME & GRATING MODULO TAF TAF FLANGES & EXTENSION Depending on installation, TAF flanges can be removed or used for wall-to-wall installation. In wallto-wall installation, wall tiles are placed upon the TAF flanges for a perfect fit between the wall tiles, floor tiles and the drain. Extension flanges, which extend the total length up to 4, are available for sale. Details on TAF Extension sets: page 14 1 2 3 4 5A CENTERED TAF 5B WALL-to-WALL TAF 5C WALL MOUNTED TAF WALL 9
5D WALL-to-WALL TAF Wall 5E CENTERED DESIGN sets SEE PAGE 14 FOR INFO ON SIDE FLANGE EXTENSION 6 WALL FILL UP SEE INSTALLATION DIAGRAM: P.12 & 13 (WALL) 7 10
INSTALLATION EXAMPLE 11
INSTALLATION DIAGRAM NO-HUB SLEEVE 2 3 4 5 7 6 8 9 10 1 12 13 11 PLYWOOD CONCRETE 1 rough (Side outlet) 2 TAF (Tile Adjustable Frame) 3 TAF Grating 4 Elastic sealant - Silicone 5 Tiles 6 Thin set tile adhesive 8 Pre-assembled waterproofing membrane 9 Thin-set sheet membrane (entire floor!) 10 Sloped mortar bed 11 Pan liner / Moisture resistant material 12 No-hub sleeve 13 Drainage pipe 7 Grout *Not included with the drain. 12
INSTALLATION DIAGRAM - WALL NO HUB SLEEVE 14 2 3 4 5 7 6 8 9 10 1 12 13 11 PLYWOOD CONCRETE WALL 1 rough (Side outlet) 2 TAF (Tile Adjustable Frame) 3 TAF Grating 4 Elastic sealant - Silicone 5 Tiles 6 Thin set tile adhesive 7 Grout 8 Pre-assembled waterproofing membrane 9 Thin-set sheet membrane (entire floor!) 10 Sloped mortar bed 11 Pan liner / Moisture resistant material 12 No-hub sleeve 13 Drainage pipe 14 Concrete board *Not included with the drain. 13
TAF EXTENSION SETS WALL-TO-WALL INSTALLATION The Easy Drain TAF frame is delivered with two flanges attached. To extend the frame length, unscrew the flanges and connect the extension set pieces. All TAF Extension sets consist of two equal flanges. Basic flanges (included) Extension set (+ ) 1 1 Extension set (+2 ) 1 1 Extension set (+3 ) 2 2 Extension set (+1 ) 1 1 Extension set (+3 ) 2 2 TAF EXTENSION TAF WALL EXTENSION L + 3 (+10 cm) (MTAF-VER-100) L + 3 (+10 cm) (MTAFW-VER-100) L + 3 (+8 cm) (MTAF-VER-80) L + 3 (+8 cm) (MTAFW-VER-80) L + 2 (+6 cm) (MTAF-VER-60) L + 2 (+6 cm) (MTAFW-VER-60) L + 1 (+4 cm) (MTAF-VER-40) L + 1 (+4 cm) (MTAFW-VER-40) L + (+2 cm) (MTAF-VER-20) TAF Length (L) L + (+2 cm) (MTAFW-VER-20) TAF Length (L) max. +1 L (inch) max. +1 max. +1 L (inch) 1 max. +1 14
USA Important assembling advice: Suitable for renovation work and new construction The Easy Drain should only be installed by trained professionals in compliance with state and local building codes. To achieve the best possible result, please carefully read the installation guide. If you have any questions, please consult your supplier. Please check the content of the package for completeness and integrity before proceeding with the assembly. Do not install the drain if any deviations are noted. Should this be the case, please consult your supplier. Prior to construction, the installation procedure and its special considerations should be discussed with the tile setter. After the installation of the drain body (rough) is complete, please provide the tile setter with the complete installation guide. If the drain is used for large showers with multiple heads, please check to make sure that the drainage capacity is sufficient. If you are unsure, please consult the supplier for advice. If you do not wish to use the second drainage level (secondary water drainage), the joint between the shower drain body and the TAF (tile frame) should be sealed with a permanent sealer. We recommend taping or closing the drain opening of the shower drain with a cement cap prior to the assembly to prevent construction debris from getting into the drainage pipe. To prevent damage to the TAF (tile frame), it should be kept in the package until the final installation by the tiler. Make sure the drain is level all around. Install the sewage system in compliance with the local and national codes. Note: ensure that the sewage system is properly vented and correctly pitched. Check the drainage system and the sewer system connection for water tightness. In order to prevent hollow spaces, all empty space beneath the drain must be completely filled up and sealed with floor pavement up to the top edge of the drain flange. The seal must be in compliance with the state and local standards. When tiles are being fitted, the pitch of the tiles (min. 2% per 3 3 ( 1m 1 )) in the shower must always be sloped towards the drain. The tiles should be laid level or 3/64 ( 1 mm) higher than the top edge of the tile frame to ensure good drainage toward the shower drain. Note: the requirements with regard to the floor gradient may be different for walk-in showers with glass walls. Please consult your supplier in this respect. Once the tiles have been fitted, the joint between the tiled floor and the TAF (tile frame) should be permanently sealed with an elastic sealant (maintenance joint). The adhesion surfaces should be free of mortar, adhesive and other adhesion-reducing materials. The drain is only intended for use with waste water common in households. Do not use other fluids as well as cleaning agents with the potential to damage sanitary equipment, drainage equipment and raw materials. If the drain is used for other purposes (e.g. swimming pools), where it may come in contact with aggressive cleaning agents or corrosive substances such as salt or chlorine, please consult your supplier. Construct the floor according to state and local building codes. Compliance with this installation advice is required for any warranty claims. Deviation from the installation instructions will void the warranty. Caution! Tile cleaning products often contain aggressive chemicals that are abrasive in nature and may damage the drain. Please ensure that the drain is thoroughly flushed after using any tile and grout cleaning products. 10 Years limited warranty only applies when constructed according to all installation instructions. Glass gratings are not suited for wheelchair accessibility. MAINTENANCE INSTRUCTIONS Do not use abrasives and/or sharp/scraping objects to clean the Easy Drain. The hair catcher should be cleaned periodically to remove any dirt that may have collected. We recommend the use of Easy CLEANSET for daily maintenance and cleaning of your Easy Drain. Typing and printing errors reserved. Easy Sanitary Solutions BV excludes all liability for any damages whatsoever associated with the use and/or the installation of the drain. Easy Sanitary Solutions BV a priori excludes any liability whatsoever. 15
Easy Drain Easy Drain USA Collection P.O. Box 844820 Dalles, TX 75284-4820 tel. 855-627-3626 fax. 855-627-7928 email: sales@easydrainusa.com www.easydrainusa.com Easy Sanitary Solutions Nijverheidsstraat 60 7575 BK Oldenzaal, The Netherlands tel: +31 (0)541 200800 email: info@esspost.com www.easydrain.com ESS PRODUCTS ARE PATENTED AND REGISTRATED TRADEMARKS MADE BY ESS E60.03.12.00.09 11.13