APPLICATION OF NEW GMAW WELDING METHODS USED IN PREFABRICATION OF P92 (X10CRWMOVNB9-2) PIPE BUTT WELDS ABSTRACT Michael URZYNICOK ZELKOT, Koszęcin, POLAND Krzysztof KWIECIŃSKI, Jacek SŁANIA INSTITUTE OF WELDING, Gliwice, POLAND Paola MARIANI TenarisDalmine, Dalmine, ITALY Marian SZUBRYT TÜV NORD, Katowice, POLAND Welding of collector pipes, flat heads, dished ends and connector pipes performed with high temperature and creep-resistant steels most often has been performed using GTAW process combined with MMA processes. Progress in GMAW process and availability of high quality filler materials (solid wires) enables welding of the above connections also using this method. In order to prove its efficiency, this article presents the results of related tests. The range of tests was similar to that applied during the qualification of welding procedure. The investigation also involved microscopic and fractographic examinations as well as creep test. The results reveal that welding with GMAW is by no means inferior to a currently applied SMAW method yet the time of the process is shorter by 50%. The article present the world s first known positive results in welding of P92 grade steel using GMAW welding method. INTRODUCTION The production of critical structures of power boiler pressure elements requires special attention to be attached to the quality of welded joints. In order to accomplish this objective the manufacturer of power engineering equipment must be supported by advanced technological solutions as steel grades intended for operation at higher temperature are characterised by limited weldability and thus demand complete supervision and monitoring at pre-weld, welding and post-weld stages. Most steel grades used in operation at high temperature and, in particular, martensitic chromium-molybdenum steels require pre-heating, maintaining proper inter-pass temperature and post-weld heat treatment of the joint usually through stress relief annealing. The whole process of production of butt joints, especially in case of collector pipes of diameters exceeding 114.3 mm and wall thickness over 10 mm, using standard technologies applied today proves time-consuming and costly. Therefore it remains desirable to further improve the welding process, reduce joint production time, significantly decrease labour costs without compromising high mechanical and plastic properties of welded joints, process purity and low noxiousness to the welder [1, 2]. Until today collector pipes of water-tube steam boilers are welded with GTAW (root layer) and with covered electrode (filling-up and cap layers). The combination of both methods guarantees high quality of joints but, unfortunately, increases their production time. The major factors prolonging the welding process time are additional operations such as removal of slag or spatter. In addition, welding with covered electrodes is connected with significant emission of welding fumes and gases known to be detrimental to welder s health [2].
The availability of welding consumables in the form of solid wires as well as access to modern welding equipment enabled GMAW, and in particular, pulse current-based to be used on welding of higher temperature materials [2, 4]. GENERAL CHARACTERISTICS OF P92 STEEL Martensitic steel 9Cr-1Mo-0.25V designated as P/T91 was developed in the USA in order to meet the needs of nuclear and conventional power engineering. In Europe the steel is designated as X10CrMoVNb9-1. The modifications of the chemical composition of P91 steel consisting in the reduction of molybdenum content by approx. 0.5% and addition of 1.7% tungsten resulted in the development of steel whose creep resistance is by approx. 30% higher than that of P91 grade. The steel obtained through the aforesaid modifications was designated as P92 or NF616 or, otherwise as, X10CrWMoVNb9-2. Tungsten, similarly to molybdenum, is an element enhancing solid solutions as it increases recrystallisation temperature thus improving long-term stability of matrix at higher temperature. Through stabilising carbides a microaddition of boron used in P92 steel increases its creep resistance and limits excessive liberation of carbides on grain boundaries [5]. The chemical composition of steels with 9% Cr content is presented in Table 1; the comparison of mechanical properties of such steels is presented in Table 2. Table 1. Comparison of chemical composition of 9%Cr steels according to EN 10216-2 [6] Grade Chemical composition, % C Si Mn Cr Mo Nb Co V W Others P91 0.08-0.2-8- 0.18-0.3-0.6 0.85-1.05 0.06-0.1-0.12 0.5 9.5 0.25 - N=0.03-0.07 P92 0.07-8.5-0.15- N=0.03-0.07 <0.5 0.3-0.6 0.3-0.6 0.04-0.09-1.5-2 0.13 9.5 0.25 B=0.0005-0.005 E911 0.09-0.1-8.5-0.18- N=0.05-0.09 0.3-0.6 0.9-1.1 0.06-0.1-0.9-1.1 0.13 0.5 9.5 0.25 B=0.0005-0.005 PB2* 0.135 0.076 0.31 9.28 1.51 0.053 1.33 0.19 - N=0.026 B=0.0091 * test melt data Table 2. Comparison of mechanical properties of 9%Cr steels according to EN 10216-2 [6] Mechanical properties Grad e R e, MPa R m, MPa A min., % SUBJECT OF INVESTIGATION P91 450 630 19 P92 440 620 19 E911 450 620 19 PB2* 601 754 19 The subject of investigation included butt-welded joints of pipes (OD x WT 219.1 x 31.75mm) made of X10CrWMoVNb9-2 (P92) steel. The heat analysis of the steel as delivered is presented in Table 3, whereas its mechanical properties are detailed in Table 4.
Table 3. Heat analysis of tested P92 steel grade Chemical composition, % Grade C Si Mn Cr Mo V W Others B-0.002 P92 0.15 0.22 0.45 9.14 0.4 0.16 1.97 N-0.039 Table 4. Mechanical properties of tested P92 steel grade [5] Mechanical properties Grade Re, MPa Rm, MPa A, % HV KV, J P92 666 805 23 252 118 WELDING CONSUMABLES Nb-0.055 Ni-0.11 Properly selected welding consumables are decisive for obtaining required joint properties. Their role is to ensure that the chemical composition of the weld and its mechanical properties will be as close to those of the parent metal as possible. Table 5 presents welding consumables while welding test joints [5, 7]. Table 5. Welding consumables used for P92 steel grade Method Filler metal Diameter Manufacturer, designation Welding consumables used with P92 steel (X10CrWMoVNb9-2) SMAW E ZCrMoWVNb 9 0.5 2 B 4 2 H5 3.2; 4 Böhler Thyssen Thermanit MTS 616 GMAW G ZCrMoWVNb 9 0.5 1.5 1.2 Böhler Thyssen Thermanit MTS 616 GTAW W ZCrMoWVNb 9 0.5 1.5 2.4 Böhler Thyssen Thermanit MTS 616 WELDING PROCESS Today the most widespread method of producing butt-welded joints of headers is Gas Tungsten Arc Welding of the root combined with filling performed with a covered electrode. GTAW was applied in the research for comparison-related purposes; the other method was GMAW with double pulse current. Prior to welding the joints were prepared as shown in Figure 1a. The welding process involved the production of a root run and filling runs as shown in Figure 1b. Pure argon was used as a backing gas. The test joints were produced in 1G rotating position [1-3]. a) b) Figure 1. Joint preparation diagram: weld groove geometry (a), weld run sequence (b)
WELDING THERMAL CYCLE AND POST-WELD HEAT TREATMENT Prior to welding the pipe was heated up to 200 C. During welding the inter-pass temperature was subject to continuous monitoring and did not exceed 280 C. Temperature was measured in the weld area as well as about 50 mm from the weld grove on pipe surface. After the completion of welding the joints were cooled down to ambient temperature. The welding thermal cycle and the diagram of post-weld heat treatment are presented in Figure 2 [5]. Figure 2. Welding and PWHT cycle EXAMINATION PLAN The production of welded joints was followed by non-destructive tests i.e. VT, PT and RT in 100% scope. The tests were performed taking into consideration quality level B according to standard EN ISO 5817. After obtaining positive NDT results, the joints were sampled for specimens for destructive tests (see the diagram in Figure 3). Figure 3. Manner of cutting specimens out of butt-welded joints of tubes
The scope of mechanical tests included the static tensile test of the welded joint (samples R1 and R2), bend test (samples GB1 GB4 side bend tests), impact tests (samples S1 S6 notch cut in the weld; samples H1 H6 notch cut in HAZ), macroscopic examination (sample MA), microscopic examination (sample MA), hardness measurements (sample MA) and fractographic examination from impact tests. WELDING TIME MEASUREMENT During the production of all joints related welding times were measured for comparative purposes. The measurements were performed so that it would be possible to assess the total time necessary for the production of a welded joint. The final result is then composed of welding time, time for inter-run cleaning of welds, electrode exchange time as well as time for removing splinters and slag. Total time measured for butt welding of P92 pipe 400 375 Time [min] 350 300 250 200 150 100 50 0 GTAW/SMAW Welding process 149 GTAW/GMAW Figure 4. Total time measured for butt welding of P92 pipe RESULTS OF TENSILE TESTS The tests were performed according to standard EN 895 and aimed to determine the tensile strength (Rm) of the welded joint as well as verify the results in relation to the minimum Rm value for the parent metal (PM), which according to EN 10216-2 standard stands at 620 MPa. In the diagrams the value was marked with a thick line (Figure 5). The tests revealed that all the welded joints underwent rupture outside the weld and met strength and quality related requirements.
770 720 Results of tensile test of P92 butt welded joints 732 728 670 Rm [MPa] 620 570 520 470 420 GTAW/SMAW Welding process GTAW/GMAW Figure 5. Results of tensile test of butt welded joints RESULTS OF IMPACT TESTS OF WELDS AND HAZ The tests in question were performed in order to determine the impact energy of weld and that of HAZ. Standard EN 12952-6 sets the minimum value of impact energy in HAZ at 24J and that in the weld at 27J; both values being provided for ambient temperature conditions. In the diagrams the said values were marked with thick lines (Figure 6). The impact energy results concerning the weld and HAZ are higher than the values specified in the cited standard. Impact strength in P92 butt welded joints PM Weld metal HAZ 160 140 146 146 132 Impact strenght [J] 120 100 80 60 40 46 87 37 20 0 GTAW/SMAW Welding process GTAW/GMAW Figure 6. Impact strength of weld metal in butt welded joints
RESULTS OF HARDNESS MEASUREMENTS OF WELDED JOINTS The hardness tests were conducted according to standards EN 15614-1 and EN 12952-6. In the aforementioned standards the maximum value specified for joints subject to heat treatment stands at 350 HV10. Figure 7 presents the arrangement of hardness measurement points, whereas Figures 8-9 present the results of corresponding measurements. All the results are considerably lower than the maximum allowed values and thus confirm the proper selection and performance of welding process and heat treatment. Figure 7. Hardness measurement points in butt welded joints Hardness arrangement welding process GTAW/SMAW Line A Line B Hardness (HV10) 280 270 260 250 240 230 220 210 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Measurement point Figure 8. Hardness results for GTAW/SMAW welded joint
Hardness arrangement welding process GTAW/GMAW Line A Line B Hardness (HV10) 280 270 260 250 240 230 220 210 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Measurement point Figure 9. Hardness results for GTAW/GMAW welded joint RESULTS OF MACROSCOPIC METALLOGRAPHIC TESTS The examination was performed according to standard EN 1321. The criterion applied for assessment-related purposes was quality level B according to standard EN ISO 5817. The aforesaid quality requirement was met in case of all of the joints. Figure 10 presents the results of macroscopic examination of the joint welded with SMAW (left) and those related to the joint produced with GMAW (right). Figure 10. Macrostructure of butt welded joint; methods: SMAW (left), GMAW (right) RESULTS OF MICROSCOPIC METALLOGRAPHIC TESTS The microscopic examination, which was performed according to standard EN 1321, did not reveal any microcracks and confirmed the presence of proper microstructure in all the zones of the joints made of P92 martensitic steel. Figure 11 contains microscopic examination areas (marked). Table 6 presents the results of microscopic examination in the form of photographs and description of the structures present in the characteristic areas of the welded joint.
Figure 11. Areas of microscopic examination in butt welded joint Table 6. Examples of result of microscopic examination of butt welded joint SMAW GMAW parent metal area 1, mag. 500x, etch. FeCl 3 tempered martensite tempered martensite HAZ area 2, mag. 500x, etch. FeCl 3 tempered martensite tempered martensite weld area 3, mag. 500x, etch. FeCl 3 tempered martensite tempered martensite FRACTOGRAPHIC EXAMINATION RESULTS The fractographic examination was conducted on the fractures following the impact test and involved the samples welded with GMAW (sample series 1) and joints welded with SMAW (sample series 2).
The topography of fractures of welds welded with method GMAW following the impact test are presented in figure 12a), whereas the HAZ fractures are presented in figure 12b). Figures 13a) and 13b) present the fractures of the weld and HAZ welded with SMAW respectively. The fractographic analysis and microanalysis of the chemical composition of precipitates in the weld welded with the covered electrode reveals that the joint was produced properly and should meet the requirements of operation at higher temperature. The aforesaid fact is confirmed by impact energy values, which for the weld and HAZ amounted to 49J and 87 J respectively. Also the hardness of the joint, which did not exceed 280 HV, confirms the correctness of the applied technology. During fractographic examination both MC carbides and MX carbonitridies were found. Both precipitates were analyzed with chemical microanalysis and it was found that chromium carbides and tungsten carbides were present in weld and HAZ. During fractographic examination both MC carbides and MX carbonitridies were found. Both precipitates were analyzed with chemical microanalysis and it was found that chromium carbides and tungsten carbides were present in weld and HAZ. a) b) Figure 12. Weld topography for GMAW process a) b) Figure 13. Weld topography for SMAW process In all cases it was possible to observe mixed plastic-brittle fracture with rare scrap cracks. Such morphology is characteristic of tempered martensite structures. As opposed to SMAW no anomalies were diagnosed for the samples welded with method GMAW.
CREEP TESTS RESULTS Four creep specimens were taken from the welded joints: two specimens from the GTAW plus covered electrode welded material and two specimens from the GTAW plus GMAW welded joint. The stress to apply at 600 C was calculated according to ECCC guidelines; one specimen for each welding method was loaded to reach 10000h, while the second specimen was intended to get to 20000h. At present, the duration of those creep tests is around 8000h. Figure 14. Creep tests of butt welded joints CONCLUSIONS On grounds of the tests it was possible to formulate the following conclusions: 1. Both NDT and DT confirmed high quality butt-welded joints made of P92 steel in workshop conditions. 2. There s over 50% time advantage while using Gas Metal Arc Welding compared to Shielded Metal Arc Welding 3. The application of GMAW method reduces impurities and increases the comfort of welder s work. 4. Base on the performed examinations it can be concluded that weld properties in service temperature will meet the standard requirements.
ACKNOWLEDGEMENTS The authors of the article wish to express their thanks to ZELKOT, Poland for the idea of this research and welding of pipes, TenarisDalmine, Italy for providing the pipes used for the investigations, BÖHLER Schweißtechnik, Deutschland for providing the covered electrodes and solid wires used for welding P92 steel and Institute of Welding, Poland for all carried examinations. REFERENCES [1] Urzynicok M., Kwieciński K., Szubryt M., Słania J.: Application of new gmaw welding methods used in prefabrication of P92 (X10CrWMoVNb9-2) pipe butt welds. 9th Liege Conference on Materials for Advanced Power Engineering, September 27th - 29th, Liege, Belgium [2] Urzynicok M., Kwiecinski K., Slania J., Szubryt M., Mariani P.: Comparison of SMAW and GMAW Methods used in P92 Butt Welds. 1st Australasian International Welding, Inspection and NDT (iwin2013) Conference, 10-13 March 2013, Perth, Australia [3] Kwieciński K., Urzynicok M., Łomozik M.: Practical experience with welding new generation steel PB2 assigned for power industry. 9th Liege Conference on Materials for Advanced Power Engineering, September 27th - 29th, Liege, Belgium [4] Urzynicok M., Kwiecinski K., Szubryt M.: Experience in the welding of martensitic steel VM12-SHC, Welding International, ifirst article 2011, 1-6 [5] Urzynicok M., Szubryt M.: A new approach to welding collector pipes performed with 16Mo3 grade steel, Welding International, Volume 25, Issue 8, 2011 [6] EN 10216-2+A2. Seamless steel tubes for pressure purposes. Technical delivery conditions. Non-alloy and alloy steel tubes with specified elevated temperature properties [7] Heuser H., Jochum C., Alloy design for similar and dissimilar welding and their behaviors. 1st International Conference Super-High Strength Steels. Rome, (2-4.11.2005). CODES AND STANDARDS USED: 1. ISO 5817: Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections 2. EN 10216-2: Seamless non-alloy and alloy steel tubes for pressure purposes with specified elevated temperature properties 3. ISO 6892-1: Metallic materials - Tensile testing - Part 1: Method of test at room temperature 4. ISO 4136: Destructive tests on welds in metallic materials - Transverse tensile test 5. EN 12952-6: Water-tube boilers and auxiliary installations. Inspection during construction. Documentation and marking of pressure parts of the boiler 6. ISO 9016: Destructive tests on welds in metallic materials - Impact tests - Test specimen location, notch orientation and examination 7. EN 10045-1: Charpy impact test on metallic materials. Test method (V- and U-notches) 8. ISO 15614-1: Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys 9. ISO 5173: Destructive tests on welds in metallic materials - Bend tests 10. EN 1321: Destructive test on welds in metallic materials. Macroscopic and microscopic examination of welds