DRAINAGE GUTTERS FOR DRAIN ASPHALT 2012 TECHNICAL CATALOGUE

DRAINAGE GUTTERS FOR DRAIN ASPHALT 2012 TECHNICAL CATALOGUE

TABLE OF CONTENTS Drainage gutters and drain bodies Chapter 01 Page - Installation diagram - Installation diagram - Drainage gutter (cast iron) with centrical nozzle - Drainage gutter (cast iron) with centrical nozzle - Drainage gutter (cast iron) with front side nozzle - Drainage gutter (cast iron) with front side nozzle - Drainage gutter (stainless steel), width 170 mm - Drainage gutter (stainless steel), width 170 mm - Drainage gutter (stainless steel), width 300 mm - Drainage gutter (stainless steel), width 300 mm - Base parts - Figures of stainless steel gutters 04 05 06 07 08 09 10 11 12 13 14 15 02 Subject to technical changes - with Höllko

DRAINAGE GUTTERS INSTALLATION DIAGRAM SYSTEM DESCRIPTION 03

drainage gutters installation diagram FIGURE 1 Höllko offers two different systems of drainage gutters. The variant made of stainless steel (see figure 1) is basically produced without slope. Therefore, it must be installed by the customer at a slope angle of at least 2%. FIGURE 2 In order to position the gutter, an installation and adjustment aid is required, for example the wooden structure shown on the left. Figure 2 shows an adjusted cast iron gutter. 04 Subject to technical changes - with Höllko

drainage gutters installation diagram STAINLESS STEEL GUTTER 5 1 2 3 4 6 1 ROAD SURFACE MADE OF DRAIN ASPHALT 2 INTERMEDIATE LAYER MADE OF MASTIC ASPHALT 3 PROTECTIVE LAYER MADE OF MASTIC ASPHALT 4 WATER-PERMEABLE REACTION RESIN CONCRETE WITH EPOXY RESIN BINDER 5 SEALED JOINTS 6 SEALING LAYER CAST IRON GUTTER 5 1 2 3 4 6 Subject to technical changes - with Höllko 05

Product description/tender specification Drainage gutter made of cast iron with 130 drainage holes laterally on the roadway side (ø 20mm) Gutter length 3950mm, width 330mm, height 138mm with 2 fix and 3 hinged grids (L = 800mm), slot width 30mm, with hinge and friction lock (square 14mm made of stainless steel) DIN EN 124/1229, test load class D 400, material GGG (spheroidal cast iron) slope (2 %) towards the centre on both sides Outer pipe diameter nozzle = 150mm (200mm) Inlet cross section grid 5160cm² Inlet cross section drainage openings 408cm² Installation option: - As gutter system individually or connected to each other TOP VIEW 3950 SECTION 138 2% 290 ND 150 VIEW 06 Subject to technical changes - with Höllko

drainage gutters made of cast iron Drainage gutter made of cast iron ND Length mm kg Item no. 150 3950 480 ER1100DN150SM 200 3950 480 ER1100DN200SM 71710 Ordering notes: Base parts on page 14 Sludge traps and adapters upon request 47 330 CROSS-SECTION 330 100 2% DETAIL 50 50 Ø20 Subject to technical changes - with Höllko 07

Product description/tender specification Drainage gutter made of cast iron with 130 drainage holes laterally on the roadway side (ø 20mm) Gutter length 3950mm, width 330mm, height 138mm with 2 fix and 3 hinged grids (L = 800mm), slot width 30mm, with hinge and friction lock (square 14mm made of stainless steel) DIN EN 124/1229, test load class D 400, material GGG (spheroidal cast iron) Outer pipe diameter nozzle = 150mm (200mm) Inlet cross section grid 5160cm² Inlet cross section drainage openings 408cm² Installation option: - As gutter system individually or connected to each other TOP VIEW 3950 SECTION VIEW 08 Subject to technical changes - with Höllko

drainage gutters made of cast iron Drainage gutter made of cast iron ND Length mm kg Item no. 150 3950 480 ER1100DN150SS 200 3950 480 ER1100DN200SS 71710 Ordering notes: Base parts on page 14 Sludge traps and adapters upon request 47 330 CROSS-SECTION 330 250 100 ND 150 DETAIL 50 50 Ø20 Subject to technical changes - with Höllko 09

drainage gutters made of stainless steel Product description/tender specification Drainage gutter made of stainless steel with 20 vertical drainage openings (per running metre) attached laterally (on the roadway side) (slot 43x8mm) Suitable for drain asphalt, material thickness 4mm, grid with mesh width 21 x 21mm Number and size variable, DIN EN 1433, test load class D 400 Material stainless steel 1.4404 / 1.4571 Drain nozzle ND 100 (ND150), position drain nozzle variable Flange or plug-and-socket connection Standard lengths 1000mm, 2000mm, 3000mm, 6000mm, as well as adapters as required Width 170mm, height 74mm Grids screwed 4 times Inlet cross section grid (running metre) 1165cm² Inlet cross section drainage openings 69cm² - Different materials and dimensions upon request - Optional with folding grids TOP VIEW 1000 1000 VIEW DETAIL PLUG-AND-SOCKET CONNECTION TOP VIEW (enlarged) DETAIL PLUG-AND-SOCKET CONNECTION SECTION (enlarged) DETAIL PLUG-AND-SOCKET CONNECTION VIEW (enlarged) 1000 1000 170 12 45 1000 1000 12 45 170 174 74 53 PLUG-AND-SOCKET CONNECTION WITH ADHESIVE CONCRETE ANCHOR OPTIONAL 10 Subject to technical changes - with Höllko

drainage gutters made of stainless steel 71710 Drainage gutter made of stainless steel kg per running ND Length mm metre Item no. 100 1000 22 ER1200DN100-L1000 150 1000 22 ER1200DN150-L1000 100 2000 22 ER1200DN100-L2000 150 2000 22 ER1200DN150-L2000 100 3000 22 ER1200DN100-L3000 150 3000 22 ER1200DN150-L3000 100 6000 22 ER1200DN100-L6000 150 6000 22 ER1200DN150-L6000 Ordering notes: Base parts on page 14 Sludge traps and adapters upon request 170 DETAIL FLANGE CONNECTION VIEW (enlarged) 1000 POSITION OF THE DRAIN NOZZLE VARIABEL DETAIL FLANGE CONNECTION TOP VIEW (enlarged) DETAIL FLANGE CONNECTION SECTION (enlarged) DETAIL FLANGE CONNECTION VIEW (enlarged) 1000 1000 210 170 1000 1000 174 170 95 74 53 CONCRETE ANCHOR OPTIONAL Subject to technical changes - with Höllko 11

drainage gutters made of stainless steel Product description/tender specification Drainage gutter made of stainless steel with 20 vertical drainage openings (per running metre) attached laterally (on the roadway side) (slot 43x8mm) suitable for drain asphalt, material thickness 4mm, grid with mesh width 21 x 21mm Number and size variable, DIN EN 1433, test load class D 400 Material stainless steel 1.4404 / 1.4571 Drain nozzle ND 150 (200), position drain nozzle variable Flange or plug-and-socket connection Standard lengths 1000mm, 2000mm, 3000mm, 6000mm, as well as adapters as required Width 300 mm, height 74mm Grids screwed 4 times Inlet cross section grid (running metre) 2071 cm² Inlet cross section drainage openings 69cm² - Different materials and dimensions upon request - Optional with folding grids TOP VIEW 1000 1000 10 VIEW POSITION OF THE DRAIN NOZZLE VARIABEL DETAIL PLUG-AND-SOCKET CONNECTION TOP VIEW (enlarged) DETAIL PLUG-AND-SOCKET CONNECTION SECTION (enlarged) DETAIL PLUG-AND-SOCKET CONNECTION VIEW (enlarged) 1000 1000 300 12 45 1000 1000 12 45 300 174 74 53 PLUG-AND-SOCKET CONNECTION WITH ADHESIVE CONCRETE ANCHOR OPTIONAL 12 Subject to technical changes - with Höllko

drainage gutters made of stainless steel 71710 Drainage gutter made of stainless steel kg per running ND Length mm metre Item no. 150 1000 43 ER1300DN150-L1000 200 1000 43 ER1300DN200-L1000 150 2000 43 ER1300DN150-L2000 200 2000 43 ER1300DN200-L2000 150 3000 43 ER1300DN150-L3000 200 3000 43 ER1300DN200-L3000 150 6000 43 ER1300DN150-L6000 200 6000 43 ER1300DN200-L6000 Ordering notes: Base parts on page 14 Sludge traps and adapters upon request 300 DETAIL FLANGE CONNECTION VIEW (enlarged) 1000 DETAIL FLANGE CONNECTION TOP VIEW (enlarged) DETAIL FLANGE CONNECTION SECTION (enlarged) DETAIL FLANGE CONNECTION VIEW (enlarged) 1000 1000 340 300 1000 1000 300 174 95 53 74 CONCRETE ANCHOR OPTIONAL Subject to technical changes - with Höllko 13

BASE PARTS Product description/tender specification Base part made of stainless steel 1.4404 / 1.4571 for drainage gutter with insulating flange, with concrete ring ND 100 (ND 150, ND 200) length 500mm, wall thickness 2mm with clamping flange and soak slots, 4-fold screw connection M10 with metal plate cover 71710 TOP VIEW (drain body) TOP VIEW (clamping flange) TOP VIEW (cover metal plate) DIM. F 50 R10 20 53 R16 60 DIM. G Ø10 DIM. E DIM. B DIM. G 32 DIM. B DIM. J T=2 151 DIM. H 31 DIM. A 31 DIM. J 53 53 SECTION (drain body) SECTION (clamping flange) TOP VIEW (cover metal plate on flange) 80 DIM. A 80 SOAK SLOT 67 6 72 6 2 DIM. B 2 3 DIM. H 5 5 10 L 5 DIM. C The opening of the drain nozzle towards the base part must be closed by using the supplied cover metal plate. 2 2 DIM. D Base parts made of stainless steel ND Length mm Dimension A Dim. B Dim. C Dim. D Dim. E Dim. F Dim. G Dim. H Dim. J Item no. 100 500 149 149 153 108 104 309 204 254 211 ERUT100 150 500 200 200 204 159 155 360 255 305 262 ERUT150 200 500 247 247 251 206 202 407 302 352 309 ERUT200 14 Subject to technical changes - with Höllko

FIGURES OF stainless steel gutters Special designs according to the customer's specifications are possible. The gutter bodies made of stainless steel can be extended at the constuction site. The type with folding grid and sludge trap is shown here. A connecting tunnel between the gutter pieces may also assume a height compensation function. Subject to technical changes - with Höllko 15

93183 Kallmünz, Germany Phone +49 (0) 9473 9407-0 Fax +49 (0) 9473 9407-49 email info@hoellko.com Internet www.hoellko.com A branch of the Höllein group of companies. www.hoellein-gruppe.de THIS CATALOGUE MAY NOT BE REPRODUCED WITHOUT THE PERMISSION OF R. HÖLLEIN CAROLINENHÜTTE GMBH & CO. KG. ALL FIGURES, DRAWINGS, AND LOGOS SHOWN ARE PROTECTED BY COPYRIGHT. THE TECHNICAL DATA IN THIS CATALOGUE IS SUBJECT TO CHANGES. WE RESERVE ERRORS. OUR INFORMATION IS PROVIDED WITHOUT COMMITMENT AND MUST BE CHECKED IN EACH INDIVIDUAL CASE. DRAINAGE GUTTERS FOR DRAIN ASPHALT 2012 - DATING FROM NOVEMBER 2011.