GREENHOUSE ENGINEERING PREFABRICATED HOUSES
WOODEN HOUSES Prefabricated wooden houses are made of wooden bearing structure with mineral wool, with a vapor barrier. On the inside, construction is lining with gypsum boards or paneling, and on the outside it is lining with the wooden cladding. We have created models, that vary according to its size and type. Houses can be made with a client desire using an advice from the design team of our company
Building a home is of great importance for every individual, and our company offers the possibility to realize the desire, using prefabricated timber that achieves better quality of the structure and a good quality of life. Prefabricated houses that we produce are not built on the site, but partly manufactured in the factory in the form of panels or modules and then transported to the construction site. Many of these homes can be easily adapted to the specifics of the location of the building, making this form of construction far more flexible and modern than before. Today, to design prefabricated house is a challenge for any architect. Design is becoming more inventive with a use of various geometric shapes and eco - friendly materials. This type of house follows the development of the current green architecture and sustainable construction and housing. Another big advantage is the fact that after the construction of this houses, after it stays little construction waste.
EXTERNAL WALLS d= 40,0 cm CONSTRUCTION ELEMENTS The core of the wall is a load-bearing construction made of glued laminated wood, d=20, sheathed on both sides with a gypsum fiber fermacell (knauf, regips) panel d=1.25 cm. It is filled with rock wool d=20, which has a Delta-Dawi water membrane on the inside, and a Delta-Maxx windproof/vapor permeable membrane on the exterior. Spacing is installed on the gypsum fiber-fermacell board on the interior: a wooden construction d=5 cm with rock wool insulation filler d=5 cm closed off with a gypsum fiber-fermacell board d=1.5 cm. On the exterior gypsum fiber-fermacell board, a vapor permeable polystyrene board, d=10, is installed, which is coated in construction glue, and silica stucco as a final finish. System EuroMAX
EXTERNAL WALLS d= 30,6 cm The wall elements are produced with impregnated load-bearing wooden constructions - KVH, 16 cm wide, which are sheathed on both sides with gypsum fiber fermacell (knauf, regips) boards d=1.25 cm (or OSB board), filled with rock wool d=16, with a vapor membrane. Gypsum fiber fermacell (knauf, regips) boards d=1.25 cm are installed on the interior walls, and the exterior walls are boarded with polystyrene d=10 cm, coated with construction glue with netting, and finished with silica stucco. System Standard U=0,140 W/m²K
EXTERNAL WALLS d= 36,8 cm The wall elements are produced with impregnated load-bearing wooden constructions - KVH, 16 cm wide, filled with rock wool d=16 cm, with a Delta Dawi GP vapor membrane. On the exterior, gypsum fiber - fermacell boards (knauf, regips) d=1.25 cm are installed, while OSB boards d=1.2 cm are installed on the interior walls. A spacing construction is constructed on the OSB board d=5 cm, filled with rock wool d=5 cm, with a gypsum fiber board d=1.25 cm + gypsum board d=1.25 cm. The exterior walls are boarded with polystyrene d=10 cm, coated with construction glue with netting, and finished with silica stucco. System Euro U=0,118 W/m²K
EXTERNAL WALLS PASSIVE HOUSE WALLS d= 45.8 cm The wall elements are produced from impregnated load-bearing wooden constructions - KVH, 22 cm wide, insulated with rock wool d=22 cm, and a Delta Dawi GP vapor membrane. A gypsum fiber fermacell (knauf, regips) board d=1.25 cm is installed on the exterior over the wooden load-bearing construction, while the interior is sheathed with OSB d=1.2 cm. A spacing construction is installed on top of the OSB board - a wooden construction d=8 cm, insulated with rock wool d=8 cm, which is sheathed with a gypsum fiber fermacell (knauf, regips) board d=1.25 cm + gypsum board d=1.25 cm. The exterior walls are boarded with polystyrene d=10, coated with construction glue with netting, and finished with silica stucco. System Mega U=0,093 W/m²K
EXTERNAL WALLS ECONOMIC ( RECOMMENDED ) Based on our experience and previous customer requirements throughout Europe, we recommend Economic wall. Facilitated version of Mega package with greater strength, greater bearing capacity, greater weight and easy assembly of the walls on the spot. The wall elements are produced from massive load-bearing wooden structure, 20 cm wide, insulated with mineral wool d=20 cm, and a Delta wurt DB90pare-vapor membrane. An OSB water-resistantboard d=1.2 cm is installed on the exterior over the wooden load-bearing construction, while the interior is sheathed with OSB d=0.9 cm. A spacing construction is installed on top of the OSB board - a wooden construction (or metallic construction) d=8 cm, insulated with rock wool d=8 cm, which is sheathed with a double gypsum boards (knauf,farmacel or regips) d=2x1.25 cm. The exterior walls are boarded with polystyrene d=12cm, coated with construction glue with netting, and finished with silica stucco. External parts of the walls are made in a factory and assembled on site, while the internal side of the walls is assembled on site after completing installation works. From the experience, this kind of system work shortens design time, shortens the development in the workshop, allowing for greater flexibility of installation works and reduces errors during assembly to a minimum. TOTAL WIDTH OF THE ECOMOMIC WALLS d= 45 cm Of course we can meet clients' wishes and requirements of the country where the house is assembling.
INTERNAL WALLS The wall elements are produced with impregnated load-bearing wooden constructions 10 and 12 cm wide, filled with rock wool d=6 cm (or more), sheathed with gypsum fiber board d=1.25 cm (or OSB board) on both sides, with another layer of gypsum board d=1.25 cm. The total thickness of the non-load-bearing walls is d=15 and 17 cm. WALL HEIGHT The standard height of wall elements is 2.70 m, and if necessary, the walls can be constructed taller. The interior height from floor to ceiling with the standard wall construction is 2.56 m, depending on the height of the floor construction. FLOOR CONSTRUCTION Constructed of KVH joists, with dimensions and spacing according to the static calculation, with mineral wool d=10 cm, and d=20 in overhangs. On the bottom, lathing is installed to which fireproof gypsum board d=1.25 cm. OSB board d=1.8 cm is installed on the top side, which then receives sound insulation, cement screed, and a final flooring finish, depending on the use of the space. CEILING CONSTRUCTION The ceiling construction for single-level and multilevel homes is the bottom of the roof truss, which is covered in lathe, and fireproof gypsum board d=1.25 cm, filled with mineral wool of a thickness in accordance with the thermal calculation with a vapor membrane. The ceiling construction for houses with an attic: mineral wool with a vapor membrane in the roof slope, and the central dropped ceiling, with lathe and fireproof gypsum board d=1.25 cm.
MODELS OF THE PREFABRICATED WOODEN HOUSES GREENHOUSE ENGINEERING
House with attic with a living room, kitchen, dining room, guest toilet and a large terrace on the ground floor. The top floor has two loose bedrooms with bathroom. Pgross = 151.3 m 2 Pnet = 123.3 m 2 MODEL 1
Ground floor
First floor
One-storey house with living room, kitchen connected with a dining room, guest toilet and a bedroom that can be used as a study room. Above the kitchen is a large ceiling which gives the impression of space and commotion. Two loose rooms with private bath are located on the first floor, as well as a second living room with gallery above the kitchen and a large terrace. The living room on the first floor can be easily transformed into a separate bedroom. Pgross = 171.8 m 2 Pnet = 136.4 m 2 MODEL 2
Ground floor
First floor
Storey house with each floor design as two separate units, two separate apartments. There is also the possibility of merging them into one common unit. Flat 1: Ground floor apartment with a huge living room and huge diningkitchen area with access to a front and back yard. Flat 2: Located on the first floor. It is design as a modern open space with kitchen, dining and living room, and with separate living area with two bedrooms. Flat has exit on two separate huge terraces from the living room and bedroom block. P gross = 392 m 2 P net = 178.2 m 2 (S1) + 146 m 2 (S2) P terrace = 20.3 m 2 (S1) + 68 m 2 (S2) MODEL 3 - LUX
Ground floor apartament S1
First floor apartment S2
Luxury villa with three bedrooms, each room has its own bathroom. House is equipped with living room with a double storey height and large glass portal leading to the backyard. The ground floor has also a library or office room and diningkitchen block. The house has a fitness room and a garage which are located below the ground floor. P gross = 510 m 2 ( 362 m 2 ground levels + 148 m 2 underground) P net = 418.7 m 2 ( 120.3 m 2 level -1 + 187.8 m 2 level 0 + 97.1 m 2 level 1 + 13.5 m 2 terrace) MODEL 4 - LUX
Underground floor Level -1
Ground floor Level 0
First floor Level 1
Modern house with three large bedrooms and two bathrooms placed on the first floor. On the ground floor are located dining room and living room in one big unit and a separate area for the kitchen and the study room. The house design is very suitable for expansion and reducing the floor area without spoiling the house design. In front of the building there is covered parking place for two vehicles. P gross = 288 m 2 P net = 201.5 m 2 P terrace = 33.3 m 2 MODEL 5
Ground floor
First floor
One-storey house with living room, kitchen, dining room and guest toilet on the ground floor. On the first floor are located three bedrooms with a bathroom. There is the possibility of making a flat terrace on the first floor above the living room. Also, covered parking place is located below the first floor. P gross = 134.72 m 2 P net = 102.85 m 2 MODEL 6
Ground floor
First floor
Modern mountain house with high and sloping roof designed as a three bedroom apartment with three bedrooms located upstairs. The ground floor has living-dining area, kitchen and guest toilet. P gross = 116 m 2 P net = 87 m 2 MODEL 7
Option 1
Option 2
An example of connecting the existing building with the newly built modern part of the building. With this example we want to show that using ours building system it is possible not only to build the new objects but also to work very easy with an upgrading of existing buildings. P gross new = 135 m 2 P net = 114 m 2 MODEL 8
Beside making prefabricated houses in our offer you can count on very good quality of aluminum windows and doors. Long-term cooperation with top producers that export to EU and other world markets for many years, gives our facilities special esthetic expression and raise the quality off our houses to a higher level. Manufacture of joinery is based on Greek supplier ALUmil, profiles with all recognized European certificates. From our offer, we choosed the following systems: - Alumil M11000 - Alumil M23000 - Alumil M300 - Alumil S100 - Alumil S700 - Alumil S 60 - Alumil SD95 ( luxury entrance doors )
M11000 Alutherm Plus - flexible system with interrupted thermal bridge for the doors and windows of all kinds, certified vto meet the requirements of thermal insulation, sound insulation and security. - With different design solutions (straight, curved, angled, classical) -Ideal for both business and residential area. A diverse selection of frames, minimal, modern, neoclassical, traditional stainless steel. - Possibility of installation of aluminum shutters and aluminum mosquito nets. M 11000
M23000 Forestal belongs to an exclusive offer Alumil in the system with a thermal break especially based on the heat and sound insulation, and high safety standards. This system is a combination of superior aluminum quality with unquestionable style and esthetics of wood. Compound of aluminum and wood achieved by a special tabs that allow air to circulate, preventing corrosion due to condensation. M23000 is considered system of higher security levels by using a special locking mechanism. As a result achieved 30 minutes Anti-theft for protection in its class to WK3 certificate IFT Rosenheim. Also, polyamide width of 24 mm, is applied in this system raising the thermal insulation, and achieving Uf = 2.1 W/m2K. Possibility of installation of aluminum shutters and aluminum mosquito nets. M 23000
M300 Falcon is a complete system with interrupted thermal bridge for largevolume lift and sliding doors, capacity up to 400 kg per wing, which gives sorution for all types of glazed openings, with the unique option of opening, including a very good thermal insulation.. types of thermal insulation - 20mm polyamide for increased thermal insulation. Thermal insulation - Uf = 3.2 W/m2K M 300 FALCON
S 100 is a thermal brake system for sliding doors with a very small depth of the vent, of only 32mm, retaining all good technical characteristics of range of thermal brake sliding systems of ALUmil. S 100
S 700 is a TOP class lift-slide system for very large openings with impressive, out off competition, characteristics. Very low face sash of only 84 mm. -Interlocking face width of only 47mm for double sash sliding doors, for maximum visibility and door hight of up to 3m. -Intelligent water evacuation system, perfect for heavy rain-falls S 700
S 60 Alutherm Super, technologically advanced system with interrupted thermal bridge for windows and doors of all species, with increased thermal insulation. Meet European standards of world-class in the field of heat and sound insulation, impact resistance of wind and water resistance to IFT Rosenheim. Possibility of installation of aluminum shutters and aluminum mosquito nets. S 60
SD 95 is a system for entrance doors with advanced characteristics. -Maximum enrgy efficiency with achievable thermal insulation up to Ud< 1,0 W/m2 k -Increacsed sound insulation. -Big dimensions of the doors. -Variery of security locks. SD 95
GREENHOUSE ENGINEERING www.greenhouseing.com