8 4 5 6 9 16 10 15 11 SOFFIT 19 OUTSIDE CORNER 20 21 INSIDE CORNER 3 22 23 12 13 OPENING 14 END WALL 17 18 7 4 5 6 ELEVATION FOR DETAIL REFERENCE ONLY CSV-01 CSV-02 CSV-03 CSV-04 CSV-05 CSV-06 CSV-07 CSV-08 CSV-09 CSV-10 CSV-11 CSV-12 CSV-13 CSV-14 CSV-15 CSV-16 CSV-17 CSV-18 CSV-19 CSV-20 INDEX STANDARD PANEL OFFERING SIDE LAP DETAILS WALL SECTIONS WALL SECTIONS WALL SECTIONS BASE DETAILS BASE & PARAPET DETAILS STACK JOINT DETAIL HORIZONTAL REVEAL DETAILS HEAD OPENING DETAILS JAMB OPENING DETAILS - (HIGH CELL & LOW CELL) JAMB OPENING DETAIL - () SILL OPENING DETAILS HEAD, JAMB, SILL INTERSECTION (MICROLINE) HEAD, JAMB, SILL INTERSECTION () END WALL DETAILS - (HIGH CELL & LOW CELL) END WALL DETAILS - () SOFFIT DETAILS OUTSIDE CORNER DETAILS CSV-21 INSIDE CORNER DETAILS CSV-22 PENETRATION (1 of 2) CSV-23 PENETRATION (2 of 2) INDEX NOTE: DETAILS ARE FOR PROMOTIONAL USE ONLY. FOR COMPLETE DETAILS, REFER TO CENTRIA'S WEB SITE AT www.centria.com CSV-01
16" [406] EXTENDED FASTENER LEG 1.6 [41] 2.4 [61] CS-660E 7 8 " [22] CS-660 Panel Option For Use With Attachment Clips and Fixing point fastener 16" [406] EXTENDED FASTENER LEG 9.6 [244] CS-630E 7 8 " [22] CS-630 Panel Option For Use With Attachment Clips and Fixing point fastener 16" [406] EXTENDED FASTENER LEG 5.6 [142] 5.6 [142] CS-620E 7 8 " [22] CS-620 Panel Option For Use With Attachment Clips and Fixing point fastener 16" [406] EXTENDED FASTENER LEG 9.6 [244] CS-610E 7 8 " [22] CS-610 Panel Option For Use With Attachment Clips and Fixing point fastener 12" [305] EXTENDED FASTENER LEG 1.6 [41] 2.4 [61] CS-260E 7 8 " [22] CS-260 Panel Option For Use With Attachment Clips and Fixing point fastener 12" [305] EXTENDED FASTENER LEG 5.6 [142] CS-220E 7 8 " [22] CS-220 Panel Option For Use With Attachment Clips and Fixing point fastener 12" [305] EXTENDED FASTENER LEG 5.6 [142] CS-210E 7 8 " [22] CS-210 Panel Option For Use With Attachment Clips and Fixing point fastener 12" [305] EXTENDED FASTENER LEG 9.6 [244] CS-200E 7 8 " [22] CS-200 Panel Option For Use With Attachment Clips and Fixing point fastener CSV-02 Dec 12
CS-660E 16"[406] NOMINAL COVERAGE CS-630E 16"[406] NOMINAL COVERAGE CS-620E 16"[406] NOMINAL COVERAGE CS-610E 16"[406] NOMINAL COVERAGE CS-260E 12"[305] NOMINAL COVERAGE CS-220E 12"[305] NOMINAL COVERAGE CS-210E 12"[305] NOMINAL COVERAGE SIDE LAPS CS-200E 12"[305] NOMINAL COVERAGE CSV-03
DRAINED & VENTED CAVITY INTERIOR SHEATHING STUD CONCEPT SERIES PANEL WITH EXTENDED FASTENING LEG (NO CLIP REQUIRED) HORIZONTAL 3/4" [19] DEEP 16 GA. INSULATION PANELS ON PROTECTED WITH CAVITY INSULATION VAPOR RETARDER LOCATION THE LOCATION OF THE VAPOR (DIFFUSION) RETARDER IS NOT IDENTIFIED IN THIS DETAIL BECAUSE IT IS A REQUIREMENT THAT VARIES BY CODE JURISDICTION, CLIMATE AND INTERIOR CONDITIONS. THEREFORE THE BUILDING DESIGNER MUST MAKE THIS DETERMINATION. = NOT BY CENTRIA DRAINED & VENTED CAVITY CONCEPT SERIES PANEL WITH EXTENDED FASTENING LEG (NO CLIP REQUIRED) HORIZONTAL 1/2" [13] DEEP 16 GA. HORIZONTAL GIRTS BARRIER (PROVIDED BY FACE PANEL) VERTICAL LINER PANEL WITH FACTORY APPLIED SEALANT AIR BARRIER (LINER PANEL) FIELD-APPLIED (1.65 PCF) INSULATION IN LINER CAVITY PANELS WITH INSULATION IN VERTICAL LINER = NOT BY CENTRIA CSV-04 Aug. 11
CONCEPT SERIES PANEL WITH EXTENDED LEG FASTENING (NO CLIP REQUIRED) METALWRAP INSULATED BACK-UP PANEL FASTEN PANEL THROUGH EXTENDED LEGS "A" "A" METALWRAP CONT. ZEE AT EACH PANEL SIDE JOINT (36" O.C.) METALWRAP INSULATED BACK-UP PANEL SECTION A-A CONCEPT SERIES PANEL 3 4 " DRAINED & VENTED CAVITY PANELS WITH METALWRAP INSULATED BACK-UP PANEL = NOT BY CENTRIA DRAINED & VENTED CAVITY CONCEPT SERIES PANEL WITH EXTENDED LEG FASTENING (NO CLIP REQUIRED) FASTEN PANEL THROUGH EXTENDED LEG INTO ZEES CON'T. HORIZONTAL ZEE 16 [1.52] GA. MIN. (SPACING TO BE DETERMINED BY CLADDING ENGINEER) INTERIOR SHEATHING STUD INSULATION SUITABLE FOR MOISTURE EXPOSURE PANELS WITH INSULATION OUTBOARD OF STUD CAVITY VAPOR RETARDER LOCATION THE LOCATION OF THE VAPOR (DIFFUSION) RETARDER IS NOT IDENTIFIED IN THIS DETAIL BECAUSE IT IS A REQUIREMENT THAT VARIES BY CODE JURISDICTION, CLIMATE AND INTERIOR CONDITIONS. THEREFORE THE BUILDING DESIGNER MUST MAKE THIS DETERMINATION. = NOT BY CENTRIA CSV-05 Aug. 11
MASONRY FASTENER (*) CONTINUOUS HORIZONTAL ZEE SHAPED (SHIM AS REQUIRED) (*) S SHALL BE 1.) 16 GA. MINIMUM. 2.) 3/4" [19] MINIMUM DEPTH. 3.) SPACED AT 24" [610] OR 48"O.C. [1219] BASED ON DESIGN LOADS AND INSULATION SIZE. CONCEPT SERIES PANEL WITH EXTENDED FASTENING LEG (NO CLIP REQUIRED) MASONRY INSULATION SUITABLE FOR MOISTURE EXPOSURE AIR BARRIER & WATER RESISTANT COATING OR MEMBRANE DRAINED & VENTED CAVITY PANELS WITH INSULATION OVER MASONRY WALL VAPOR RETARDER LOCATION THE LOCATION OF THE VAPOR (DIFFUSION) RETARDER IS NOT IDENTIFIED IN THIS DETAIL BECAUSE IT IS A REQUIREMENT THAT VARIES BY CODE JURISDICTION, CLIMATE AND INTERIOR CONDITIONS. THEREFORE THE BUILDING DESIGNER MUST MAKE THIS DETERMINATION. = NOT BY CENTRIA CONCEPT SERIES PANEL WITH EXTENDED FASTENING LEG (NO CLIP REQUIRED) HORIZONTAL GIRTS FINISH IS REQUIRED ON BOTH SIDES OF THE PANEL SINCE BOTH SIDES ARE EXPOSED TO THE WEATHER PANELS USED AS A SCREEN WALL = NOT BY CENTRIA CSV-06 Aug. 11
STUDS TAPE DESIGN OF BASE MUST VARY TO SUIT CONCRETE PLACEMENT AND FORMING TOLERANCES 5" [127] BASE DETAILS (CS-7503) 2" [51] 2" [51] SP-4222 SEALANT BASE DETAILS (CS-7503B) STUDS TAPE CENTER LINE OF SP-4144 SP-4142 SP-4141 SEALANT 1 3 4 " 9 16 " [14] B\EXTRU [44] 3 3 8 " [86] TOP OF RETAINER (SP-4141) = NOT BY CENTRIA CSV-07
PARAPET 5 SLOPE 2"[51] MIN. METAL CLOSURE STUDS PARAPET (CS-7010) STUDS TAPE T/CURB 1 8 "[3] GAP BASE DETAIL () (CS-7003) 1"[25] B/FLASH = NOT BY CENTRIA CSV-08
TAPE 1 8 "[3] CLR. STUDS METAL CLOSURE STACK JOINT (CS-7004) = NOT BY CENTRIA CSV-09
STUDS SP-4170 2" [51] SP-4142 1" [25] METAL CLOSURE SP- 4169 HORIZONTAL REVEAL (CS-7504) SP-4173 STUDS 5" [127] SP-4173 METAL CLOSURE SP-4169 HORIZONTAL REVEAL (CS-7504A) = NOT BY CENTRIA CSV-10
BARRIER AND AIR STUDS TAPE SP-4143 METAL AND COMPOSITION CLOSURES HEAD OPENING () (CS-7500) 2" [51] CLEAR OPNG. SP-4142 DOOR, WINDOW OR LOUVER SHIM AS REQUIRED SP-4141 TAPE 1/8"[3] GAP WEATHER SEAL HEAD OPENING ( ) (CS-7000) STUDS CURING BUTYL EXTEND VPWB PRIMARY AIR SEAL DOOR, WINDOW OR LOUVER R.O. B/SUPPORT = NOT BY CENTRIA CSV-11
STUDS EXTERIOR SHEATHING 6"[152] MAXIMUM CANTILEVER CLEAR OPNG. PRIMARY AIR SEAL DOOR, WINDOW OR LOUVER SHIM AS REQUIRED SP-4143 TAPE SP-4141 2" [51] JAMB OPENING (HIGH CELL) (CS-7502) STUDS 6"[152] MAXIMUM CANTILEVER CLEAR OPNG. PRIMARY AIR SEAL SHIM AS REQUIRED WEATHER SEAL TAPE SP-4143 JAMB OPENING (LOW CELL) (CS-7502A) 2" [51] DOOR, WINDOW OR LOUVER = NOT BY CENTRIA CSV-12
R.O. STUDS PRIMARY AIR SEAL CURING BUTYL DOOR, WINDOW OR LOUVER WEATHER SEAL 4" [102] JAMB OPENING () (CS-7002) JAMB DETAILS = NOT BY CENTRIA CSV-13
CLEAR OPNG. SP-4145 2" [51] METAL CLOSURE SP-4141 TAPE STUDS SILL OPENING () (CS-7505) 2 1 2 "[64] MIN. WINDOW OR LOUVER METAL CLOSURE SILL OPENING () (CS-7005) STUDS = NOT BY CENTRIA CSV-14
INTERSECTION OF HEAD, JAMB & SILL S (CS-7513) = NOT BY CENTRIA CSV-15
INTERSECTION OF HEAD, JAMB & SILL (CS-7013) = NOT BY CENTRIA CSV-16
TAPE 6"[152] MAXIMUM CANTILEVER STUDS SUPPORT FLASH SP-4141 SP-4144 END WALL (HIGH CELL) (CS-7506) 2" [51] TAPE 6"[152] MAXIMUM CANTILEVER STUDS SP-4144 END WALL DETAILS SUPPORT FLASH SP-4144 END WALL (LOW CELL) (CS-7506A) 2" [51] SP-4141 = NOT BY CENTRIA CSV-17
TAPE BARRIER AND AIR STUDS SUPPORT FLASH END WALL at HIGH CELL () (CS-7006) 4"[102] MIN. NON-CURING BUTYL POLYURETHANE TAPE BARRIER AND AIR STUDS SUPPORT FLASH END WALL at LOW CELL () (CS-7006) 4"[102] MIN. NON-CURING BUTYL POLYURETHANE = NOT BY CENTRIA CSV-18
BARRIER AND AIR STUDS TAPE SOFFIT - FRONT () (CS-7016) METAL AND COMPOSITION CLOSURES STUDS METAL AND COMPOSITION CLOSURES 2 1 2 "MIN. [64] 2 1 2 "MIN. [64] METAL CLOSURE BARRIER AND AIR SOFFIT - BACK () (CS-7017) = NOT BY CENTRIA CSV-19
DESIGN MAY VARY DUE TO PANEL MODULE LAYOUT STUDS SP-4172 SP-4171 SUPPORT FLASH 6"[152] MAX. CANTILEVER BARRIER AND AIR 4 1 8 " [105] OUT SIDE CORNER () (CS-7507) STUDS SUPPORT FLASH 4 1 2 "[114] MIN. OUT SIDE CORNER OUT SIDE CORNER ( ) (CS-7007) = NOT BY CENTRIA CSV-20
STUDS SP-4141 SP-4144 TAPE 6"[152] MAXIMUM CANTILEVER SUPPORT FLASH (CS-7509B) DESIGN MAY VARY DUE TO PANEL MODULE LAYOUT STUDS 4 1 2 "[114] MIN. SUPPORT FLASH INSIDE CORNER (CS-7009) = NOT BY CENTRIA CSV-21
NOTE:- REF. PAGE CSV-23 FOR SECTS. A-A & B-B PENETRATION DETAIL (CS-7012) = NOT BY CENTRIA CSV-22 Aug. 11
TAPE 1 8 '[3] GAP ANGLE STUDS SECTION A-A (CS-7012A) TAPE TAPE PENETRATION DETAIL SECTION B-B (CS-7012B) POLYURETHANE SEALANT (TYPICAL ALL AROUND) EXTERIOR SHEATHING = NOT BY CENTRIA CSV-23