GLUING AND RIVETING Sikaflex 221, black Elastic Sikaflex 221 is a high-adhesion, polyurethane-based sealing compound for Low-odour connecting and overlapping joints, apron panels, trims, floor assemblies and for Non-corrosive various sealing tasks. Recoatable 81 22 9 407 5 00 ml 1 Adhesive Set, 2K Easy to use. The Adhesive Set, 2K is a dual-component polyurethane adhesive that is perfect A conventional cartridge gun can for structural bonds that are subject to loads and for bonding attachment parts, be used for application such as roof spoilers. This adhesive can be used to bond plastics, composite materials and painted parts together. 8 19 0 41 84 Set 1 NEW Betalink K2 Only for Remote Engine Start For bonding the key for the USA Remote Engine Start Set. 8 19 2 444 028 2 x 100 ml 1 Adhesive Set, 1K Easy to use. The Adhesive Set, 1K is a single component, high-adhesive, elastic and air After just 48 hours, it is possible to moisture curing adhesive and sealant based on polyurethane. It is suited for go through the car wash bonding painted surfaces, plastics, aluminium, stainless steel,, ABS, carbon fibre composite, PUR-RIM, polycarbonate, soft PUR, hard PUR, hard PVC, wood and glass. 82 69 9 408 866 Set 1 NEW Betaprime 5402 Bonding agent for adhesive set 2K (8 19 0 41 84) and adhesive set 1K (82 69 9 408 866). 8 19 2 446 515 15 ml 1 Body adhesive K1 Can be pumped cold The body adhesive K1 is a one-component structural adhesive for repairing Excellent bonding to the steel weight-reduced aluminium front section components (GRAV) and for bonding grades used in the automotive bodywork components made of aluminium (e.g. for E60). industry Also suitable for sealing, thus protecting both the metal and the welds from corrosion 8 19 0 41 015 195 ml 1
Body Adhesive K2 Good adhesion to plastics, Body Adhesive K2 is a dual-component polyurethane adhesive with very long composites, painted and coated open time at room temperature, which was specially developed for structural metal surfaces bonding. The adhesive consists of hardener and adhesive, one component per Low temperature-dependency of cartridge. the module Glass transition outside application scope 8 19 2 55 849 2 x 290 ml 1 Activator Betawipe 4800 Betawipe 4800 is a adhesion-promoting activator for pretreatment for carbon fibre composite bonding with Body Adhesive, K2. 8 19 2 57 707 10 ml 1 Cartridge Gun for Bodywork Adhesive K2 No leakage of the adhesive The cartridge gun is perfect for applying the K2 body adhesive. Easy to use Quick reload Simple pressure regulation 81 49 2 55 475 1 pc. 1 Body Adhesive K Very high strength Body Adhesive K is a dual-component adhesive for repair CFRP components, High impact resistance such as the outer roof skin of the M6. The adhesive is generally suitable for Fast curing bonding plastics, metals, metal primers and paint coatings (2K systems), SMC and Cures at room temperature other glass-fibre reinforced materials, woods and ceramics. 8 19 0 417 144 2 x 00 ml 1 Body Adhesive K4 Cures at room temperature Body Adhesive K4 is a viscoelastic dual-component adhesive based on High shear strength methacrylate adhesive as a repair material for clips repairs of roof rails - PV 060. Excellent adhesion on a wide range of materials Suitable for use at temperatures up to 100 C 8 19 2 149 520 50 ml 1
Mixing Tube The Mixing Tube is suitable for bonding the 50 ml double cartridge Araldite (PN: 8 19 2 149 520, PN: 8 19 0 401 099). 8 19 2 149 521 1 pc. 5 Adhesive Gun Adhesive gun for bonding the 50ml double cartridge Araldite. Matches 50 ml double cartridge (PN: 8 19 2 149 520, PN: 8 19 0 401 099, PN: 8 19 2 158 654). 8 19 2 149 522 1 pc. 1 HIGHLIGHT Body adhesive K5a Corrosion protected and can be 2C adhesive for bonding body parts. The only product to be used in the event welded through of a warranty claim. Impact-resistant modified 2-component cartridge adhesive Can be coated over and sanded based on epoxy resin, which is mixed using a static mixing tube. Provides corrosion Excellent thermal and chemical protection, is weldable, when cured can be painted and sanded. resistance 8 19 2 158 654 50 ml 1 HIGHLIGHT Body adhesive K5b Corrosion protected and can be 2C adhesive for bonding body parts. The only product to be used in the event welded through of a warranty claim. Impact-resistant modified 2-component cartridge adhesive Can be coated over and sanded based on epoxy resin, which is mixed using a static mixing tube. Provides corrosion Excellent thermal and chemical protection, is weldable, when cured can be painted and sanded. resistance 8 19 2 157 298 195 ml 1 Mixing Nozzles Set K5a and K5b Mixing nozzles for 2K adhesive for bonding body parts. For K5a (PN 8 19 2 158 654) for K5b (PN: 8 19 2 157 298). 8 19 2 44 550 Set 1 per set 10 pcs
Adhesive Set K6 Fast curing Contains: 1x 10 g Dual component adhesive, 1x 10 ml Primer, 2x Dosing tips, Easy to use instructions and stamp. Dual component superfast adhesive, bridges gaps with Can be used on many materials primer for bonding small parts such as PDC sensors. For retrofitting and repairing all PDCs in the various vehicle derivatives. For flexible flanges, machined surfaces or cast flanges, bumpers, metal and plastic combinations, leather, cable fixing etc. 8 19 2 17 925 Set 1 Mixing Nozzles K6 Set The mixing nozzle set consists of a set of mixing nozzles for the K6 Adhesive Set. 8 19 2 6 502 1 pc. 10 Drei Bond 185 Anaerobic Adhesive High temperature resistance Special type high-strength, high temperature resistant. Specially developed for High-strength curing thread and joint connections subjected to high temperatures. Immediate tightness Good creeping property in the case of difficult material combinations such as polyamide plugs in cylinder Fast curing heads or as V2A core removing hole cover in aluminium engine blocks. Screw sealing agent for repair Changing radial shaft seal rear axle gearbox drive for the flange nut. 8 19 0 417 76 50 g 1 Adhesive Set for Inside Mirror Araldite 201 Low shrinkage Room-temperature-curing, highly viscous, epoxy resin-based 2C adhesive. Good Good resistance to environmental contact adhesion and stability as well as excellent resistance to environmental influences and chemicals influences and chemicals. Metal adhesive but also suitable for ceramics, glass, Suitable for vertical applications rubber, hard plastics etc. 8 19 0 401 099 50 ml 1 Cleaner R1 It can be used to clean various N-heptane cleaner for pre-treating for adhesion. The R1 cleaner with n-heptane is materials, such as glass, paint, and used to clean surfaces of contaminants prior to bonding. plastic parts Particularly effective removal of non-polar contaminants such as oils and greases 8 19 2 211 217 100 ml 1
Primer P1 As per the warranty from BMW, an The primer (bonding agent) is required for pretreatment of surfaces during repair approved product for pretreatment bodywork. during bonding and repair of body parts 8 19 0 02 556 50 ml 1 Primer P2/ Gas Cartridge As per the warranty from BMW, an The primer (bonding agent) is required for pretreatment of surfaces during repair approved product for pretreatment bodywork. during bonding and repair of body parts 8 19 0 02 555 50 ml 1 Spiral drill 6.8 mm, highly stable Newly developed, extremely These drills have been specially developed for machining high-strength steels. robust cutting geometry, which Using them, several holes can be drilled in high strength steels without losing their greatly reduces the occurrence cutting properties. The products have been specially developed and adapted for of thermal loads on the drill tip in the high BMW Group demands by the supplier. machining high-strength materials and special alloys Handling/functionality: There is a wide range of applications, and therefore it is the ideal solution in the automotive industry, aerospace technology, power plant construction, and in the chemical industry Due to good wear protection, the drill has a long service life 8 19 2 59 262 1 pc. 1 d=6.8 mm L=79 mm 4.2 mm twist drill, high-strength Newly developed, extremely These drills have been specially developed for machining high-strength steels. robust cutting geometry, which Using them, several holes can be drilled in high strength steels without losing their greatly reduces the occurrence cutting properties. The products have been specially developed and adapted for of thermal loads on the drill tip in the high BMW Group demands by the supplier. machining high-strength materials and special alloys Handling/functionality: There is a wide range of applications, and therefore it is the ideal solution in the automotive industry, aerospace technology, power plant construction, and in the chemical industry Due to good wear protection, the drill has a long service life 8 19 2 59 26 1 pc. 1 ø=4.2 mm, l=66 mm
Draw Pins for BSP 0 Draw pin (weld stud) made of V2A-SA, 6 x 40 mm for stud welder BSP-0. Use for body repair. 8 19 0 0 08 1 pc. 10 Blind Rivet N1 Blind rivet N1, Ø 6.5 mm, fastening range: 2.8-4.8 mm Product is needed for repair of body. 8 19 0 01 414 1 pc. 10 Blind Rivet N2 Blind rivet N2, Ø 6.5 mm, fastening range: 4.8-6.8 mm. Use for body repair. 8 19 0 01 419 1 pc. 150 Blind Rivet N Blind rivet N, Ø 4 mm, fastening range: 1- mm. Use for body repair. 8 19 0 01 421 1 pc. 150 Blind Rivet N6 Blind rivet N6, Ø 4 mm, fastening range: -5 mm. Use for body repair. 8 19 2 158 655 1 pc. 150
Blind Rivet N7 Blind rivet N7, Ø 6.5 mm, fastening range: 1.5-.5 mm. Use for body repair. Blind rivet for fastening body parts. 8 19 2 240 52 1 pc. 150 Blind Rivet N8 Blind rivet N8, Ø 6.5 mm, fastening range 6.8-8.8 mm. Use for body repair. The blind rivet is specifically for the i (I0). 8 19 2 55 998 1 pc. 150 Blind Rivet N9 Blind rivet N9, Ø 6.5 mm, fastening range 8.8-10.8 mm. Use for body repair. 8 19 7 29 64 1 pc. 10 Blind Rivet N10 Blind rivet N10, Ø 6.5 mm, fastening range 10.8-12.8 mm. Use for body repair. 8 19 9 144 282 1 pc. 10 Punch Rivet N4 Punch rivet N4, Ø mm, length = 4 mm. Use for body repair. 8 19 2 158 080 1 pc. 50
Punch Rivet N5 Punch rivet N5, Ø 5 mm, length = 5 mm. Use for body repair. 8 19 2 158 079 1 pc. 50 Screw SF Plus EJOT spiral form screw SF Plus M5x15 made of case-hardening steel. Treated surface A2K DIN EN ISO 4042, glide coated, galvanized, blue passivated. Use for body repair. 8 19 0 01 69 1 pc. 10 INOX Spray, Weld Priming Fast drying finish coating for spot weld sealing in inert gas and spot welding. Cathodic corrosion protection and plastic coating simultaneously, can be painted. 8 40 0 409 992 500 ml (spray) 1 Rust Primer High reaction speed > short action Rust primer is an aqueous gel for removing rust and corrosion from ferruginous time steel. The material creates a -5 mm thick film on the metal surface, which High yield > low consumption removes the rust. Environmentally friendly > no hazard symbol, R or S phrases Approximately ph neutral > no acid action in metal pores 8 19 2 57 552 500 ml 1 Dual Component Metal Putty Easy to apply High stability and temperature resistance Further processing is possible with standard metalworking tools after curing The 2K-metal putty is an epoxy resin filler, which is used in particular to repair badly damaged body surfaces and for adapting the transitions during part replacement. The 2K metal putty is also used as a replacement for the lead-containing solder. 8 19 2 154 175 446 + 54 g 1 446 (epoxy) + 54 (resin)