Save up to $50 per job!

ADHESION PROMOTER Save up to $50 per job! Comparison tests show that using Bulldog Adhesion Promoter saves both labor and material cost. Bulldog (1 coat) Bulldog (2 coats) Competitor A Competitor B Total Time to Complete Project (minutes) 14:20 17:56 26:33 66:35 Material Cost $5.31 $9.35 $27.81 $13.15 Labor Cost (est $50/hr) $11.94 $14.94 $22.13 $55.49 Total Cost $17.25 $24.29 $49.94 $68.64 Savings per Job, Using 1 Coat of Bulldog $32.69 $51.39 Savings per Job, Using 2 Coats of Bulldog $25.65 $44.35 *Based on Chicago, IL shop conditions in December 2009 *BULLDOG PABC124 Abrasive Cleaner, ETPO123B/QTPO123 Adhesion Promoter *All tests done using raw, unprimed bumper covers *Competitive tests done using the recommended products and processes, as published in manufacturer's Technical Manuals/Bulletins. All BULLDOG products are covered by a lifetime warranty. Visit our website for full terms and conditions. www.kleanstripauto.com www.bulldogsticks.com 2010 W.M. Barr & Co., Inc., PO Box 1879, Memphis,TN 38101 Phone: (877) 849-5752 Fax: (800) 621-9508

Bulldog PABC124 ETPO123B Process: Step 1 Step 2 Competitor A Clean and Scuff Pad Plastic Adhesion Wipe Advance Plastic Bond 12oz aerosol Process: Unprimed Plastic Substrates (patent pending) Tear open Clean and Scuff Pad and clean the substrate thoroughly using the scuff Step 1 pad side of the pre-saturated sponge, then rinse with water. Blow dry or wipe with a clean cloth. Tear open Plastic Adhesion Wipe and apply a light even coat on the the entire area, Step 2 wiping in one direction to minimize product overlap. Allow 3-5 minutes flash time. (note: product not dry after 5 minutes) Apply a light coat of Advance Plastic Bond. Step 3 Allow 5 minutes dry time or until completely flashed to a matte finish. Total Time to Complete Job according to instructions Total Material Cost Shop Rate: Labor @ $50/hr Total Job Cost Using Competitor A Competitor B Abrasive Cleaner 16oz Adhesion Promoter 15oz aerosol Raw/Unprimed Bumpers (1 coat) Clean all areas to be painted with PABC124. Rinse thoroughly and allow to dry. Blow and tack surface. Apply one even, medium-wet coat. Allow 5-10 minutes dry time. Total Time to Complete Job according to instructions Process: Step 1 Step 2 Raw/Unprimed Bumpers (2 coats) Clean all areas to be painted with PABC124. Rinse thoroughly and allow to dry. Blow and tack surface. Apply an even, light mist coat. Wait 3-5 minutes and apply a second coat. (note: used 3 minute dry time) Allow 5-10 minutes dry time. Total Time to Complete Job according to instructions Total Material Cost Shop Rate: Labor @ $50/hr Total Job Cost Using BULLDOG Adhesion Promoter Plastic Cleaning Paste 20oz Adhesion Promoter 15oz aero Flexible Adhesion Sealer 32oz Shop Price $10.15 $20.21 Time to complete step (minutes) 8:44 0:36 5:00 14:20 8:44 4:12 5:00 17:56 Amount Used per Job 2oz per cleaning step 3oz per coat Shop Price $10.23 $10.23 $29.37 Time to complete step (minutes) 9:04 2:21 8:26 1:42 5:00 26:33 Shop Price $21.58 $18.58 $54.53 Process: Raw, Unprimed Bumper Time to complete step (minutes) Apply 1 medium coat of Adhesion Promoter aerosol. Step 5 Allow to dry 25 minutes. Apply 1 coat Flexible Adhesion Sealer. Step 6 Allow to dry 25 minutes. Step 1 Step 3 Pre-wash with warm water and Plastic Cleaning Paste, using a gray or gold pad. Wash again with warm water and Plastic Cleaning Paste, using a gray or gold pad. Step 2 Step 4 Rinse thoroughly, making sure the paste does not dry on the surface. Rinse thoroughly, making sure the paste does not dry on the surface. Dry following the rinse. 3:49 6:13 3:10 25:00 3:23 25:00 Total Time to Complete Job according to instructions 66:35 Total Material Cost Shop Rate: Labor @ $50/hr Total Job Cost Using Competitor B Cost per Job (1 coat) $1.27 $4.04 $5.31 $11.94 $17.25 Amount Used per Job 1 pad 1 wipe 3oz per coat Amount Used per Job 2oz per cleaning step 3oz per coat 3oz per coat Cost per Job (2 coats) $1.27 $8.08 $9.35 $14.94 $24.29 Cost per Job $10.23 $10.23 $7.34 $27.81 $22.13 $49.94 Cost per Job $4.32 $3.72 $5.11 $13.15 $55.49 $68.64

PABC124 Abrasive Cleaner GTPO123, QTPO123 Adhesion Promoter (liquid) ETPO123B Adhesion Promoter (aerosol) Bulldog Adhesion Promoter is the premier adhesion promoter for the auto body collision repair market. Bulldog is a single-component product that combines an adhesion promoter and a flex agent in one. It is fast drying and provides superior adhesion on all flexible and rigid plastic parts. Features: One Component: Makes Paint Stick: Reduces Material Cost: Reduces Painting Time: No Waste: Tintable: Convenient Aerosol: Benefits: No mixing required Ready to spray Promotes adhesion on most plastic surfaces, including TPO, polypropylene, and SMC Adhesion Promoter and Flex Agent in one Dries clear in 5 minutes Unused product can be poured back into the can Tint with basecoat for visible coverage Designed for spot repair no need for a spraygun Compatible Coatings: All solvent-based urethane, epoxy, or acrylic lacquers, primers, sealers and basecoats. Compatible Surfaces: All common automotive plastic substrates, as well as, glass, chrome, aluminum, fiberglass, rubber, vinyl, and painted surfaces. Bulldog is suitable for ground effects, new flexible and rigid bumpers, as well as plastic interior and exterior parts. * Bulldog Adhesion Promoter TPO123 is restricted in California under SCAQMD Rule 1151. ETPO123B Bulldog Adhesion Promoter Aerosol is NOT affected by Rule 1151, and can be used and sold in CA. * Bulldog VOC Compliant Adhesion Promoter TPO125 is compliant in CA under SCAQMD Rule 1151. NOTE: Always apply basecoats and clearcoats according to manufacturer s instructions. 1

GTPO123/QTPO123 DIRECTIONS FOR USE: Carefully read all cautions on the MSDS before use. Protect hands with solvent-resistant gloves and eyes with chemical splash goggles. If the work area is not well ventilated you must use a properly fitted and maintained NIOSH approved respirator for organic solvent vapors. A dust mask does not provide protection against vapors. 1. Shake well and filter before each use to secure uniform mixture. 2. Clean all areas to be painted with Bulldog Abrasive Cleaner. Rinse thoroughly with water and allow to dry. Be sure not to apply any solvent cleaners after this point. 3. Blow and tack surface. 4. Using a spray gun, apply one even, medium-wet coat. NOTE: If two coats are needed, apply an even, light mist coat. Wait 3-5 minutes, and apply a second coat. 5. Wait 5 to 10 minutes before applying the next coating. Drying Times Between Coats: Dry to Next Coating: Tinting: Flex Agent: 3-5 minutes 5-10 minutes Mix 90% Bulldog with 10% basecoat for visible color coverage. Ratio 1:4 Bulldog with basecoat Ratio 1:3 Bulldog with clearcoat Note: Bulldog is effective up to 24 hours. If the sprayed part is left overnight, the basecoat can be applied with no issue. If the part is left longer than 24 hours it needs to be scuffed and tacked again. Apply 1 light coat of Bulldog before applying basecoat. Equipment Cleaning: All tools and spills should be cleaned immediately with lacquer thinner. Care should be taken to keep lacquer thinner away from freshly finished surfaces. Clean spray gun according to manufacturer s instructions. 2

TECHNICAL DATA: Appearance: Vapor Density: Percent Volatile: Flash Point: Flash Point of Concentrate: CPSC Flammability Classification: GTPO123/QTPO123 liquid, hazy, light pink to light yellow, mobile, dries to a Class A water-white finish Heavier than air 82.75% by weight 32 F Flammable VOC Category (Max Allowable V.O.C.) Specialty Coatings (National/EPA: 840 g/l CA*: 540 g/l) Actual V.O.C.: 768 g/l 6.23 lbs/gal 84.2% by weight MAX Vapor Pressure of the V.O.C.: Storage: Coverage: Shelf Life: DOT: HAPS: Density: Boiling Range: 30.6mm Hg at 20C Store between 32 F and 95 F, in the original container. up to 750 sq. ft. per gallon 2 years from date of manufacture, in an unopened container. UN1866, Resin Solution, Flammable, 3, PGII Toluene, Xylene, Ethyl Benzene, Styrene 7.5 lbs/gal 132-380 F * Note: Several CA air districts regulate non-aerosol automotive coatings. The CA limit listed is the most restrictive for those districts in the state. Product SIZE PACK LBS CUBE FT LENGTH WIDTH HEIGHT UPC CODE PALLET QTY GTPO123 GL 4 36.762 13 13 /16 8 13 /16 10 13 /16 0-30192-12325-6 52 cases QTPO123 QT 6 14.406 10 9 /16 7 1 /8 9 5 /16 0-30192-12315-7 88 cases 3

ETPO123B DIRECTIONS FOR USE: Carefully read all cautions on the MSDS before use. Protect hands with solvent-resistant gloves and eyes with chemical splash goggles. If the work area is not well ventilated you must use a properly fitted and maintained NIOSH approved respirator for organic solvent vapors. A dust mask does not provide protection against vapors. General Repair 1. Clean all areas to be painted with Bulldog Abrasive Cleaner. Rinse thoroughly with water and allow to dry. Be sure not to apply any solvent cleaners after this point. 2. Blow and tack surface. 3. Shake gently for one minute to ensure a uniform mixture. 4. Hold can in an upright position, with arrow on button pointing away from you, approximately 12 inches from the surface. 5. Spray the surface with an even, light mist coat. Wait 3 to 5 minutes and apply a second light coat, if needed. 6. Wait 5 to 10 minutes before applying the next coating. Spot & Panel Repair: Bulldog can be used before epoxy, urethane or polyester fillers to promote adhesion to polypropylene and TPO bumpers. Apply primers to all metal and filler areas. Sand all areas to be painted with 320 grit or finer. Apply 2 medium coats Bulldog, allowing 3-5 minutes flash between coats. Allow 5 to 10 minutes dry time before applying basecoat. Drying Times: Between Coats: 3-5 minutes Dry to Next Coating: 5-10 minutes Note: Bulldog is effective up to 24 hours. If the sprayed part is left overnight, the basecoat can be applied with no issue. If the part is left longer than 24 hours it needs to be scuffed and tacked again. Apply 1 light coat of Bulldog before applying basecoat. Equipment Cleaning: All tools and spills should be cleaned immediately with lacquer thinner. Care should be taken to keep lacquer thinner away from freshly finished surfaces. 4

TECHNICAL DATA: Appearance: Vapor Density: Percent Volatile: Flash Point: Flash Point of Concentrate: CPSC Flammability Classification: VOC Category (Max Allowable V.O.C.) Actual V.O.C.: MAX Vapor Pressure of the V.O.C.: Storage: Coverage: Shelf Life: DOT: HAPS: Density: Boiling Range: ETPO123B Dries to a Class A water-white finish Heavier than air 90.4% by weight 42 F Flammable Polyolefin Adhesion Promoter (2.5 MIR) 2.47 MIR Replace overcap on container after each use. Contents under pressure. Do not puncture, incinerate, or store above 120 F. Exposure to heat or prolonged exposure to sun can cause bursting. up to 100 sq. ft. per can, at 1 mil wet 2 years from date of manufacture, in an unopened container. UN1950, Aerosols, flammable, 2.1, Limited Quantity (Level 3 Aerosol) Toluene, Xylene, Ethyl Benzene, Styrene Product SIZE PACK LBS CUBE FT LENGTH WIDTH HEIGHT UPC CODE PALLET QTY ETPO123B 15 OZ. 12 16.55 11 1 /16 8 7 /16 10 3 /16 0-30192-12397-3 85 cases 5

Additional Tips for Using Bulldog Adhesion Promoter 1. Use Bulldog as a mid-coat adhesion promoter, effectively tying multiple layers of paint together. Great for use when doing special paint effects, such as flames, two-tone paint jobs, etc. Bulldog will also improve the flop/alignment of metallic pigments in blend-out areas. 2. When using Bulldog as an added flex agent in a clear, be sure to add the Bulldog after the clear has been catalyzed. (Ratio 1:3 Bulldog to mixed clear) 3. Bulldog can be added to primer in a ratio of up to 1:3. 4. Bulldog cannot be mixed with waterborne paint. However, Bulldog can be used in a waterborne system, as long as it is applied underneath the primer. Always follow paint manufacturer s instructions regarding application of waterborne paint systems. 5. Treat bare metal to prevent corrosion. Bare metal and body filler must be primed and dry or wet sanded with 320 grit sandpaper prior to applying Bulldog. 6. Metal primer overspray onto plastic surfaces should be removed, as it can cause paint failure. Bulldog overspray onto plastic is not an issue. 7. Bulldog can be used on interior parts, such as dashboards, kick panels, visors, etc., prior to dyeing or painting. Solvent-based dyes can be mixed with Bulldog (up to 50%) before application. 8. When applying Bulldog over fresh lacquer or uncured acrylics, or applying lacquers over Bulldog, allow extra dry time between light coats. 9. Bulldog should not be used on Lexan or polystyrene surfaces. 10. Bulldog is not compatible with enamel paints. 11. Abrading of the substrate is essential for successful coating application. We recommend the use of Bulldog Abrasive Cleaner on plastics, but even gentle scuffing with a red or grey scuff pad will greatly increase the bite of the coating. Bare metals, OEM painted surfaces, and previous repair coats should all be abraded prior to repainting. 6

PABC124 DIRECTIONS FOR USE: 1. Shake well. 2. Apply a 3/8 bead along face of part. Work the cleaner into the surface with a damp green or gray scuff pad. 3. Rinse thoroughly with plenty of water and wipe dry with a clean cloth. Once dry, do not wipe the surface with any type of solvent. 4. To ensure the part is ready for Bulldog Adhesion Promoter application, mist a small area with water. If sheeting occurs, dry the surface and proceed. If water beads up, repeat cleaning as directed above. beading sheeting TECHNICAL DATA: Appearance Vapor Density Percent Volatile Flash Point CPSC Flammability Classification MAX V.O.C. MAX Vapor Pressure of V.O.C. Storage Density Shelf Life DOT HAPS VOC Category PABC124 Light gray paste Heavier than air 57% by Weight None Non-Flammable, Water-Based 25 grams/liter 0.1mm Hg at 20 C Protect from freezing. Store between 32 F and 120 F. 10.1 lb/gal 2 years from date of manufacture, in an unopened container Compound Cleaning Liquid None Surface Prep for Coatings Applications Product SIZE PACK LBS CUBE FT LENGTH WIDTH HEIGHT UPC CODE PALLET QTY PABC124 PT 12 17.413 11 8 3 /8 7 3 /4 0-30192-12410-9 108 CASES 2010. W.M. Barr & Co., Inc. P.O. Box 1879 Memphis, TN 38101 800.238.2672 www.bulldogsticks.com www.kleanstripauto.com 7