/ Cermet Solution for High Speed Steel Turning The next generation coated cermet with higher wear and chipping resistance in high speed machining High Resistance to Welding and Oxidation Improved welding and oxidation resistance due to a reaction inhibiting coating film Excellent Surface Finish Preventing chemical reactions between inserts and object materials decreases surface roughness. High Toughness and Wear Resistance High Welding Resistance Excellent Surface Finish
/ High Performance Coated Cermet Grade for Machining Carbon Steel, Alloy Steel and Sintered Ferrous Alloy For high speed and continuous, the new P15 coated cermet grade, was engineered to provide improved stability in continuous turning applications at high speeds and low depths of cut. Wear resistance has been significantly improved and crater wear(kt) on the rake surface of insert is largely prevented in the continuous machining of carbon steel and alloy steel. Its highly lubricative coating layer shows excellent wear resistance and extended tool life. For high feed and interrupted To expand on the excellent performance of at high speed and continuous of a wide range of steels, was developed for machining forged steels and sintered ferrous alloy at high feed and interrupted., the new P25 coated cermet grade has a specially sintered uniformed micro grain matrix to improve stability even in the toughest machining conditions, like heavy interruptions, high feed or severe vibrations. A lubricative multi-layer coating results in largely prolonged tool life due to excellent wear resistance and toughness. The next generation cermet series / will consistently produce successful result without compromise. Minimum tolerance Stable tool life Optimal edge design Excellent surface finish Advantages Good balance of grade and chip breaker Successful in terms of geometric accuracy and tool life Applicable to carbon steel, alloy steel, bearing steel, sintered ferrous alloy, etc. Comprehensive range covering various workpiece materials 02 KORLOY TECH-NEWS
50 th Anniversary (For high speed and continuous ) P Improved performance in finish & continuous machining of hot/cold forging steel and sintered ferrous alloy. Excellent wear resistance and crater resistance. Optimized edge to improve surface finish. Features High wear resistance in high speed machining over vc(sfm)= 984 (little secondary action on workpiece) Improved wear and crater resistance Increased surface roughness with optimal edge geometries 3 1 4 Cutting Performance (Evaluation of impact resistance) Cutting time SM45C(KS), 1045(AISI), C45(ISO), Ø=3.93inch(Interrupted workpiece), L=130 vc(sfm) = 984, fn(ipr) = 0.010, ap(inch) = 0.079, wet After 2nd passes of 2.48inch, both the rake surface and major edge of insert showed no excessive wear or other problem indicators. Insert CNMG432-GM() Holder MCKNR/L12-4B Comparison of Wear 1 3 1 3 2 4 4 2 2 [ ] [ ] Comparison of Surface Roughness Improved surface finish [ ] [ ] / 03
/ (For high feed and interrupted ) P Improved performance in high feed and high interrupted machining of hot/cold forging steel and sintered ferrous alloy. Excellent anti-chipping, anti-fracture and thermal crack resistance. Optimized edge to improve surface finish. Features High chipping resistance in high feed machining over fn(ipr) = 0.010 Improved chipping resistance Stability of edge remains in high interrupted 3 1 4 Cutting Performance (Evaluation of impact resistance) Cutting time SCM435(KS), 4135(AISI), 34CrMo4(ISO), Ø=3.93inch(Interrupted workpiece), L=130 vc(sfm) = 1030, fn(ipr) = 0.010, ap(inch) = 0.059, wet After 10 minutes of machining, both the rake surface and major edge of insert showed no excessive wear or other problem indicators. Insert CNMG432-GM() Holder MCKNR/L12-4B 1 3 Comparison of Wear 1 3 2 2 4 2 4 [ ] [ ] Comparison of Surface Roughness Improved surface finish R-PROFILE Ra : 2.10 μm Rz : 9.22 μm R-PROFILE Ra : 3.06 μm Rz : 13.76 μm [ (Ra 2.10 ) ] [ (Ra 3.06 ) ] 04 KORLOY TECH-NEWS
50 th Anniversary Recommended Cutting Conditions Division Grade Recommended speed (sfm) Minimum Recommended Maximum Turning 1010 A36 1045 4140 656 1148 1476 591 951 1312 656 984 1312 591 886 1148 591 886 1148 492 820 984 Grade Lineup Cutting speed, vc(sfm) 1312 984 656 For high speed and continuous machining For high feed and interrupted machining Feed, fn(ipr) Continuous General Interrupted Chip Breaker Lineup Negative type Positive type Roughing VM GM Roughing C25 Cutting VQ Cutting HMP MP VL VB VG VL VF Excellent chip control Recommended High toughness Excellent chip control Recommended High toughness Grade Comparison Chart KORLOY A B C D PV3010 PV7010 T1500Z - PV3030 PV7020 PV90 T2000Z KT315 / 05
/ Application Examples () Alloy steel (4140) Ø1.97inch Plate carrier vc(sfm) = 1,476, n(rpm) = 2,500, fn(ipr) = 0.008, ap(inch) = 0.008, wet Insert DCMT32.51-HMP () Holder SDJCR16-3D 700ea 1000ea 45% 45% longer tool life than competitor s Carbon steel (1020) 0.79inch Ø0.59inch Nipple vc(sfm) = 558, n(rpm) = 2,000, fn(ipr) = 0.005, ap(inch) = 0.005, wet Insert TPMT221-MP () Holder S12R-STWPR2 600ea 800ea longer tool life than competitor s Alloy steel (4120) 7.09inch Ø2.48inch Pinion vc(sfm) = 820, n(rpm) = 2,500, fn(ipr) = 0.008, ap(inch) = 0.020, wet Insert DNMG441-VL () Holder PDJNR16-4D 350ea 450ea longer tool life than competitor s Sintered ferrous alloy Ø2.75inch Gear vc(sfm) = 984, n(rpm) = 2,500, fn(ipr) = 0.012, ap(inch) = 0.016, wet Insert CCMT32.51-MP () Holder SCLCR12-3B MP () 500ea 600ea 20% 20% longer tool life than competitor s 06 KORLOY TECH-NEWS
50 th Anniversary Application Examples () Alloy steel (4130) Ø0.79inch 3.43inch Valve vc(sfm) = 755, n(rpm) = 2200, fn(ipr) = 0.031, ap(inch) = 0.005, wet Insert TNMG331-VQ () Holder PTTNR10-3A 830ea 1300ea 60% 60% longer tool life than competitor s Sintered ferrous alloy Ø0.79inch Ø3.93inch Sprocket vc(sfm) = 525, n(rpm) = 500, fn(ipr) = 0.007, ap(inch) = 0.008, wet Insert SNMG432-VM () Holder MSKNR85-4D 60ea 90ea 50% 50% longer tool life than competitor s Carbon steel (1045) Ø3.15inch Cup plate carrier vc(sfm) = 984, n(rpm) = 2,500, fn(ipr) = 0.012, ap(inch) = 0.016, wet Insert CCMT32.51-C25 () Holder SCACR08-3K 40ea 60ea 50% 50% longer tool life than competitor s Carbon steel (1045) Ø1.77inch Bush CN1500 / CN2500 vc(sfm) = 656, n(rpm) = 1400, fn(ipr) = 0.004, ap(inch) = 0.012, wet Insert CCMT32.51-HMP () Holder SCLCR12-3B 1.18inch 485ea 600ea longer tool life than competitor s / 07
/ Application Examples () Carbon steel (1045).26inch Ø3.54inch Swash-Plate vc(sfm) = 820, n(rpm) = 890, fn(ipr) = 0.002, ap(inch) = 0.004, wet Insert DNMG331-VQ () Holder SDJCR16-3D 140ea 200ea 40% 40% longer tool life than competitor s 4.33inch Ductile cast iron (60-40-18) Diff. case vc(sfm) = 492, n(rpm) = 600, fn(ipr) = 0.006, ap(inch) = 0.012, wet Insert VBMT331-MP () Holder SVJBR16-3D 3.14inch 70ea 100ea 40% 40% longer tool life than competitor s Carbon steel (1035) Ø0.26inch 0.95inch Piston Rod vc(sfm) = 400, n(rpm) = 4800, fn(ipr) = 0.006, ap(inch) = 0.079, wet Insert DNMG441-GM () Holder MDQNR16-4D 400ea 600ea longer tool life than competitor s Alloy steel (1541) Ø0.98inch SHAFT vc(sfm) = 676, n(rpm) = 800, fn(ipr) = 0.012, ap(inch) = 0.006, wet Insert TCMT1.81.51-C25 () Holder S06M-STFCR-1.8 4.33inch 600ea 800ea longer tool life than competitor s 08 KORLOY TECH-NEWS
50 th Anniversary Application Examples () Alloy steel (4120) 4.72inch Ø1.96inch Connecting Rod vc(sfm) = 1,115, n(rpm) = 2100, fn(ipr) = 0.006, ap(inch) = 0.003, wet Insert TPMT221-MP () Holder S06M-STFPR-2 1400ea 1820ea longer tool life than competitor s Alloy steel (4115) Ø1.1inch Bush vc(sfm) = 1030, n(rpm) = 3500, fn(ipr) = 0.039, ap(inch) = 0.008, wet Insert CNMG432-VQ () Holder MCLNR16-4D 1.18inch 850ea 1275ea 50% 50% longer tool life than competitor s Alloy steel (1541) 0.79inch SHAFT vc(sfm) = 1204, n(rpm) = 5800, fn(ipr) = 0.001, ap(inch) = 0.061, wet Insert TBT4405R-D38-R0.25 () Holder TGTER25-4-47 2.36inch 600ea 1000ea 65% 65% longer tool life than competitor s Alloy Steel (4120) Ø0.98inch Sprocket vc(sfm) = 1115, n(rpm) = 4300, fn(ipr) = 0.006, ap(inch) = 0.003, wet Insert TPMT221-MP () Holder S06M-STFPR-2 1400ea 1820ea longer tool life than competitor s / 09
/ Chip Breaker Features Type Chip breaker Machining type Cutting edge Features VL 0 0.1 Excellent chip control when machining tough materials such as low carbon steel, pipe, steel plate, etc. Improved chip control at low depth of cut VB 6 0.1 Universal chip breaker with strong chip control at low depth of cut Excellent chip control on copying application and corner R machining Negative type VQ 0 0.23 Improved chip control with optimized edge design for medium to finish GM Roughing 0 0.25 Excellent for interrupted and high feed machining with strong edge VL 5 Improved chip control when machining low carbon steel, pipe, steel plate, etc. Positive type MP 7 0.25 Special chip breaker geometry designed for various conditions C25 Roughing 0 0.15 Strong edge produces excellent performance in interrupted and cast iron machining 10 KORLOY TECH-NEWS
50th Anniversary Available Stock Positive type Insert shape Designation CCMT Stock Machining type 21.51-VL 32.51-VL 32.52-VL 21.50.5-C25 21.51-C25 21.52-C25 32.51-C25 32.52-C25 432-C25 21.50.5-MP 21.51-MP 32.50.5-MP 32.51-MP 32.52-MP DCMT 21.51-VL 32.51-VL 21.50.5-C25 21.51-C25 21.52-C25 32.50.5-C25 32.51-C25 21.50.5-MP 21.51-MP 21.52-MP 32.50.5-MP 32.51-MP 32.52-MP SCMT 32.51-VL 32.52-VL 32.51-C25 32.52-C25 431-C25 432-C25 TCMT 32.51-VL 32.52-VL 1.81.51-C25 1.81.52-C25 21.50.5-C25 21.51-C25 21.52-C25 32.52-VL 32.52-C25 Insert shape Designation TCMT 32.51-C25 32.52-C25 32.51-MP 221-VL 221-MP VBMT 331-VL 332-VL 332-MP Negative type Insert shape Designation CNMG 431-VB 432-VB 431-VQ 432-VQ DNMG Stock Machining type to finish 431-VB 432-VB 441-VB 32.52-MP TPMT Stock Machining type 442-VB 431-VQ 432-VQ 441-VQ to finish 442-VQ SNMG 431-VB 432-VB TNMG 331-VB 332-VB 331-VQ to finish 332-VQ VNMG 331-VB 332-VB 331-VC 331-VQ 332-VQ WNMG 431-VQ 432-VQ to finish to finish / 11
Head Office Holystar B/D, 1350, Nambusunhwan-ro, Geumcheon-gu, Seoul, 08536, Korea Tel : +82-2-522-3181 Fax : +82-2-522-3184 Web : www. korloy.com E-mail : export@korloy.com Cheongju Factory 55, Sandan-ro, Heungdeok-gu, Cheongju-si, Chungcheongbuk-do, 28589, Korea Tel : +82-43-262-0141 Fax : +82-43-262-0146 Jincheon Factory 54, Gwanghyewonsandan 2-gil, Gwanghyewon-myeon, Jincheon-gun, Chungcheongbuk-do, 27807, Korea Tel : +82-43-535-0141 Fax : +82-43-535-0144 R & D Institute Cheongju 55, Sandan-ro, Heungdeok-gu, Cheongju-si, Chungcheongbuk-do, 28589, Korea Tel : +82-43-262-0141 Fax : +82-43-262-0711 R & D Institute Seoul Holystar B/D, 1350, Nambusunhwan-ro, Geumcheon-gu, Seoul, 08536, Korea Tel : +82-2-522-3181 Fax : +82-2-522-3184 620 Maple Avenue, Torrance, CA 90503, USA Tel : +1-310-782-3800 Toll Free : +1-888-711-0001 Fax : +1-310-782-3885 www.korloyamerica.com E-mail : sales@korloy.us Gablonzer Str. 25-27, 61440 Oberursel, Germany Tel : +49-6171-277-83-0 Fax : +49-6171-277-83-59 www.korloyeurope.com E-mail : sales@korloyeurope.com Plot NO.415, Sector 8, IMT Manesar, Gurgaon 122051, Haryana, INDIA Tel : +91-124-4391790 Fax : +91-124-4050032 www.korloyindia.com E-mail : sales.kip@korloy.com Av. Aruana 280, conj.12, WLC, Alphaville, Barueri, CEP06460-010, SP, Brasil Tel : +55-11-4193-3810 E-mail : vendas@korloy.com Ground Dongjing Road 56 District Free Trade Zone. Qingdao, China Tel : +86-532-86959880 Fax : +86-532-86760651 E-mail : kycpjh@korloy.com TN43-EI-01 20160810