New Supermarket Building March 13, 2017 ADDENDUM NO. 2 The following changes, additions, or deletions shall be made to the following documents as indicated and shall be a part thereof as if originally specified and/or shown. Specifications: 1. Section 08320: Add section. Clarifications: 1. The specs and wall types call for EIFS over Tyvek Commercial Wrap. The specs state for the EIFS to mechanically fastened as well as adhesively attached to provide a drainage plane. This system doesn t make sense. You would either see a mechanically fastened system with a Tyvek stucco wrap (provides the drainage plane) or a fluid applied WRB with adhesively attached EPS (vertical trowel to provide drainage). A mechanically fastened system is not ideal as labor costs are higher and it also creates more locations for the building envelope to fail (with all the penetrations). Can you get the architect to clarify exactly what they want so we are all bidding apples to apples. If they want a paper WRB product it will need to be stucco wrap or some type of drainage mat behind the foam. Again this system is not recommended by most manufacturers. Response: Provide an adhesively attached system, similar to TeifsFlex EIFS as manufactured by TEIFS. 2. The Civil drawings do not show the existing grading or the desired grade for the Outlying parcels under Segregated Pricing #1. Can you please provide? Response: See attached C1.02 & C1.02B. Mercier Architecture & Planning 3. Both 18/S5.2 and 14/S5.3 call out the steel bent frames at the entry roof as 10" x 4' x 1/4" TS. The 10/S5.3 roof plan calls out 10" x 4" x 3/8" TS. Please clarify. Response: See attached CS-03 4. Please see attached detail 20/S5.23. This detail is called out on the S5.3 high roof plan. The HSS beam shown below the WF beam doesn't appear to be called out on S5.3 high roof plan, S2.2 roof plan, or any elevation/sections. Does it exist, or is this a bad detail? Response: See attached CS-03. 5. Sheet A2.2 calls for the 2 canopy undersides to be painted to match the roof. Section N-A4.7 sends us to detail 21 & 22 on sheet A8.1 which says this location gets a perforated soffit. Please confirm that you want the soffit painted to match the roof color? Response: The large entry tower receives the metal soffit panels. The canopies that cover the widows, outdoor storage, etc have the underside of structure exposed and are to be painted to match the roof panel color. 1 P a g e
6. CE-2: For the lights on the south side of SH 54, the Contractor shall complete the trenching to the existing KEC power pole approximately 140 feet south of the edge of pavement. Prior Approvals: Drawing/Section # Item Manufacturer None Mercier Architecture & Planning 2 P a g e
Highway 54 SECTION 08320- OVERHEAD COILING SERVICE DOORS PART 1 GENERAL 1.1 SECTION INCLUDES A. Advanced Performance Rolling Service Doors. 1.2 RELATED SECTIONS A. Section 09900 - Painting: Field applied finish. 1.3 DESIGN / PERFORMANCE REQUIREMENTS A. Advanced Rolling Service doors: 1. Windload: Design door assembly to withstand wind/suction load of 20 psf (958 Pa) without damage to door or assembly components. Does not apply to doors with optional wearstrip guides. 2. Operation: Design door assembly, including operator, to operate for not less than 200,000 cycles B. Single-Source Responsibility: Provide doors, tracks, motors, and accessories from one manufacturer for each type of door. Provide secondary components from source acceptable to manufacturer of primary components. C. Products Requiring Electrical Connection: Listed and classified by Underwriters Laboratories, Inc. acceptable to authority having jurisdiction as suitable for purpose specified. 1.4 SUBMITTALS A. Submit under provisions of Section 01300. B. Product Data: Manufacturer's data sheets on each product to be used, including: 1. Preparation instructions and recommendations. 2. Storage and handling requirements and recommendations. 3. Details of construction and fabrication. 4. Installation instructions. C. Shop Drawings: Include detailed plans, elevations, details of framing members, anchoring methods, required clearances, hardware, and accessories. Include relationship with adjacent construction. D. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns. E. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) long, representing actual product, color, and patterns. OVERHEAD COILING SERVICE DOORS 08320-1
Highway 54 F. Manufacturer's Certificates: Certify products meet or exceed specified requirements. G. Operation and Maintenance Data: Submit lubrication requirements and frequency, and periodic adjustments required. 1.5 QUALITY ASSURANCE A. Manufacturer Qualifications: Company specializing in performing Work of this section with a minimum of five years experience in the fabrication and installation of security closures. B. Installer Qualifications: Installer Qualifications: Company specializing in performing Work of this section with minimum three years and approved by manufacturer. 1.6 DELIVERY, STORAGE, AND HANDLING A. Store products in manufacturer's unopened packaging until ready for installation. B. Protect materials from exposure to moisture. Do not deliver until after wet work is complete and dry. C. Store materials in a dry, warm, ventilated weathertight location. 1.7 PROJECT CONDITIONS A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits. 1.8 COORDINATION A. Coordinate Work with other operations and installation of adjacent materials to avoid damage to installed materials. PART 2 PRODUCTS 2.1 MANUFACTURERS A. Acceptable Manufacturers 1. Overhead Door Corp. 2. Wayne Dalton B. Requests for substitutions will be considered. Provide company standard Substitution Request Form. OVERHEAD COILING SERVICE DOORS 08320-2
Highway 54 2.2 ADVANCED PERFORMANCE ROLLING SERVICE DOORS A. Basis of Design: RapidSlat Model 626 Stormtite Insulated Doors by Overhead Door Corporation. PART 3 EXECUTION 3.1 EXAMINATION 1. Curtain: Interlocking roll-formed metal slats as specified with endlocks attached to each end of alternate slats to prevent lateral movement. a. Flat Profile insulated type F-265i with 24 gauge back covering for doors up to 20 feet wide fabricated of: 1) 20 gauge powder coated steel. b. Insulation: Slat cavity shall be filled with CFC-free, foamed-in-place, polyurethane insulation. 1) R-Value: 7.7, U-Value: 0.13. 2) Sound Rating: STC-21. c. Finish: 1) PowderGuard Max powder coat. (a) Color as selected by Architect. 2. Bottom Bar: Two metal angles, minimum thickness 3/16 inch, bolted back to back to reinforce curtain in the guides and incorporating a wireless, monitored safety edge. a. Material: 1) Steel. b. Steel/Aluminum Finish: 1) PowderGuard Premium powder coat in black color. 3. Guides: Three Structural steel angles. a. Material: 1) Steel. b. Steel/Aluminum Finish: 1) PowderGuard Premium powder coat in black color. 4. Door Roll: Directly driven, springless roll shall be steel tube with integral shafts, keyed on the Drive End and supported by self-aligning greaseable sealed bearings. Door shall not require any counterbalance device. 5. Hood: Protecting drive motor, barrel, chain, and sprocket from dirt and debris and extending between the support brackets. Fabricated of: a. Material: 1) Steel. b. Steel/Aluminum Finish: 1) Polyester paint in black color (steel only) 6. Brackets: Provide steel brackets to support motor, curtain, and hood and fabricated of: a. PowderGuard Premium powder coat in black color. 7. Windload Design: a. Standard windload shall be 20 PSF. OVERHEAD COILING SERVICE DOORS 08320-3
Highway 54 A. Verify opening sizes, tolerances and conditions are acceptable. B. Examine conditions of substrates, supports, and other conditions under which this work is to be performed. C. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding. 3.2 PREPARATION A. Clean surfaces thoroughly prior to installation. B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions. 3.3 INSTALLATION A. Install in accordance with manufacturer's instructions. B. Use anchorage devices to securely fasten assembly to wall construction and building framing without distortion or stress. C. Securely and rigidly brace components suspended from structure. Secure guides to structural members only. D. Fit and align assembly including hardware; level and plumb, to provide smooth operation. E. Coordinate installation of sealants and backing materials at frame perimeter as specified in Section 07900. F. Install perimeter trim and closures. G. Instruct Owner s personnel in proper operating procedures and maintenance schedule. 3.4 ADJUSTING A. Test for proper operation and adjust as necessary to provide proper operation without binding or distortion. B. Adjust hardware and operating assemblies for smooth and noiseless operation. 3.5 CLEANING A. Clean curtain and components using non-abrasive materials and methods recommended by manufacturer. OVERHEAD COILING SERVICE DOORS 08320-4
Highway 54 B. Remove labels and visible markings. C. Touch-up, repair or replace damaged products before Substantial Completion. 3.6 PROTECTION A. Protect installed products until completion of project. END OF SECTION 08320 OVERHEAD COILING SERVICE DOORS 08320-5
N:\Civil3D Projects\41242\Production Drawings\41242PL07.dwg, 3/13/2017 3:49:22 PM, tforsman, 1:1 MATCH C1.02B LEGEND COPYRIGHT 2017 Welch~Comer & Associates, Inc. This document, and ideas and designs incorporated herein, as an instrument of professional service, is the property of Welch~Comer & Associates, Inc., and is not to be used in whole or in part for any other project without the written authorization of Welch~Comer & Associates, Inc. Original Signed by: Date Original Signed: Original stored at Welch Comer & Associates, Inc. 350 E. Kathleen Ave, Coeur d'alene, ID 83815 PROJECT NO.: DESIGNED BY: DRAWN BY: CHECKED BY: DWG NAME: DATE: SHEET NO: 41242 MLC TJF 41242PL07.DWG 02-15-2017 SUPER 1 FOODS SH 54, ATHOL, IDAHO www.welchcomer.com 350 E. Kathleen Ave. Coeur d'alene, ID 83815 208-664-9382 (toll free) 877-815-5672 (fax) 208-664-5946 NO. DATE REVISION DESCRIPTION BY SITE IMPROVEMENTS AND GRADING PLAN 1 03-07-2017 ADDENDUM NO. 1, FLAG POLE NOTE, CLEANUP CONTOURS SDS TRAIL WIDTH AND GRADING 2 03-13-2017 ADDENDUM NO. 2, MATCH LINE & CLEANUP CONTOURS TJF MELISSA L. CLEVELAND 03-07-2017
N:\Civil3D Projects\41242\Production Drawings\41242PL07.dwg, 3/13/2017 4:01:39 PM, tforsman, 1:1 ADDENDUM NO. 2 MATCH C1.02 COPYRIGHT 2017 Welch~Comer & Associates, Inc. This document, and ideas and designs incorporated herein, as an instrument of professional service, is the property of Welch~Comer & Associates, Inc., and is not to be used in whole or in part for any other project without the written authorization of Welch~Comer & Associates, Inc. Original Signed by: Date Original Signed: Original stored at Welch Comer & Associates, Inc. 350 E. Kathleen Ave, Coeur d'alene, ID 83815 PROJECT NO.: DESIGNED BY: DRAWN BY: CHECKED BY: DWG NAME: DATE: SHEET NO: 41242 MLC TJF 41242PL07.DWG 03-13-2017 SUPER 1 FOODS SH 54, ATHOL, IDAHO SITE IMPROVEMENTS AND GRADING PLAN www.welchcomer.com 350 E. Kathleen Ave. Coeur d'alene, ID 83815 208-664-9382 (toll free) 877-815-5672 (fax) 208-664-5946 NO. DATE REVISION DESCRIPTION BY MELISSA L. CLEVELAND 03-13-2017
4.5 H 2 W16x36 HIGH HSS10x4x3/16 LOW 2 2 03.2017 This document, and the ideas and designs may not be reused, in whole or in part, without written permission from D'Amato Conversano Inc. D'Amato Conversano Inc. disclaims any responsibility for its unauthorized use. PROJECT NAME: SUPER 1 FOODS DESCRIPTION: PARTIAL ROOF FRAMING PLAN S2.2 PROJECT NO: DATE: BY: SHEET NO: 17041-0001 03/13/2017 DMS CS-03
1 4 2 1 4 2 2 2 1 4 1 4 03.2017 This document, and the ideas and designs may not be reused, in whole or in part, without written permission from D'Amato Conversano Inc. D'Amato Conversano Inc. disclaims any responsibility for its unauthorized use. PROJECT NAME: SUPER 1 FOODS DESCRIPTION: DETAIL 10/S5.3 HIGH ROOF FRAMING PLAN PROJECT NO: DATE: BY: SHEET NO: 17041-0001 03/13/2017 DMS CS-04