STRAINER BAGS FOR LIQUID FILTRATION Gas AND LIQUID FILTRATION
Series TPP-TPE filter bags. felt. size 1-2-3-4 CHARACTERISTICS Needle felt construction Fibre free surface treatment Silicon oil free Approved FDA material (polypropylene and polyester) (FDA 21 CFR 176.170 and FDA 21 CFR 177.1520 3.2a) Fully thermo-welded construction Rounded bottom to fit perfectly in the restrainer basket All configurations supplied with handles for easy change out Material and filtration rating stamped on the filter media Polypropylene PolyformSEAL seal ring Stainless steel or tinned steel seal ring as option Available in seven different materials Filtration rating from 1 to 200 μm MAIN APPLICATIONS Desalination Water treatment Fine chemical Petrochemical Oil & Gas Food & Beverage Power generation Paints and resin Pharmaceutical Microelectronic Galvanic General industry Rounded bottom: best fitting in the restrainer basket PolyformSEAL seal: 4 points positive seal for by-pass free filter bag Series TPP-TPE Filter Bags - Felt PolyformSEAL seal: thermo-welded seal ring for by-pass free filter bag
technical data WORKING TEMPERATURE Polypropylene 93 C Polyester 135 C Nylon 135 C Nomex 190 C PTFE 260 C DIFFERENTIAL PRESSURE Filter bag replacement: 1.7 bar @ 25 C Max allowable: 3.5 bar @ 25 C CONSTRUCTION MATERIALS Polypropylene Polyester Nylon Nomex (Aramide) PTFE DIMENSIONS Size 1: Dia. 178 x L 419 mm Size 2: Dia. 178 x L 813 mm Size 3: Dia. 102 x L 203 mm Size 4: Dia. 102 x L 356 mm FLOW RATE / DELTA-P DATA Viscosity [cp] Filtration rating [µm] 1 5 10 25 100 200 1 18.0 18.0 18.0 18.0 18.0 18.0 20 11.3 18.0 18.0 18.0 18.0 18.0 30 7.72 14.5 18.0 18.0 18.0 18.0 40 6.13 10.9 15.9 18.0 18.0 18.0 60 4.77 9.08 13.6 18.0 18.0 18.0 80 3.86 6.81 10.2 17.0 18.0 18.0 100 3.18 5.45 7.72 12.5 18.0 18.0 200 1.48 2.95 4.09 6.81 9.54 12.5 400 0.84 1.57 2.72 4.01 5.68 7.04 500 0.64 1.16 1.70 2.95 4.01 5.00 800 0.45 0.82 1.25 2.04 2.95 3.86 1000 0.39 0.68 1.02 1.66 2.27 3.41 1500 0.30 0.52 0.73 1.20 1.59 2.16 2000 0.20 0.40 0.57 0.86 1.25 1.64 4000 0.14 0.27 0.36 0.61 0.79 1.09 6000 0.09 0.18 0.27 0.43 0.59 0.77 8000 0.07 0.13 0.19 0.32 0.41 0.57 10000 0.06 0.10 0.16 0.27 0.36 0.48 Liquids flow rate (m 3 /h) - Size 1 bag - Initial Delta-P 0.07 bar For size 2 bags multiply flow rate x 1.88 For size 3 bags multiply flow rate x 0.28 For size 4 bags multiply flow rate x 0.44 AVAILABLE FILTRATION RATING Zone Polypropylene 1, 3, 5, 10, 25, 50, 100, 200 µm Polyester 1, 5, 10, 25, 50, 75, 100, 200 µm Nylon 5, 10, 25, 50, 100 µm Nomex (Aramide) 1, 5, 10, 25, 50, 100 µm PTFE 10, 25, 50 µm Recommended Good Poor Not recommended FILTERING AREA Size 1: 0.23 m 2 Size 2: 0.45 m 2 Size 3: 0.06 m 2 Size 4: 0.11 m 2 VOLUME Size 1: 6.8 liters Size 2: 15.1 liters Size 3: 1.3 liters Size 4: 2.3 liters Text in Bold: fiber, µm, sizes in stock.
Series TNY filtering bag. mesh. size 1-2-3-4 CHARACTERISTICS Mesh construction Precision woven filtration media Smooth extruded surface (nylon, polypropylene, polyester): cleanable Multiple twisted strands (polyester): high dirt holding capacity Silicone oil free Non fibre releasing Approved FDA material (polypropylene and polyester) (FDA 21 CFR 176.170 e FDA 21 CFR 177.1520 3.2a) Filter media thermo-welded to the seal ring Double and reinforced longitudinal sewn Rounded bottom to fit perfectly in the restrainer basket All configurations supplied with handles for easy change out Polypropylene PolyformSEAL seal ring Stainless steel or tinned steel seal ring as option Available in four different materials Filtration rating from 1 to 2000 μm MAIN APPLICATIONS Desalination Water treatment Fine chemical Petrochemical Oil & Gas Food & Beverage Power generation Paints and resin Pharmaceutical Microelectronic Galvanic General industry Multifilament construction: high dirt holding capacity PolyformSEAL seal: 4 points positive seal for by-pass free filter bag Series TNY Filter bags - size 1-2-3-4 Monofilament construction: high filtration precision Cleanable = high dirt holding capacity
technical data WORKING TEMPERATURE Polypropylene 93 C Nylon 135 C Polyester 135 C DIFFERENTIAL PRESSURE Bag replacement: 1.7 bar @ 25 C Max allowable: 3.5 bar @ 25 C CONSTRUCTION MATERIALS Nylon monofilament Polyester monofilament Polyester multifilament Polypropylene monofilament FLOW RATE / DELTA-P DATA Viscosity [cp] Filtration rating [µm] 150-250 300-600 600-800 1 11.0 13.8 14.8 20 11.0 13.8 14.8 30 11.0 13.8 14.8 40 11.0 13.8 14.8 60 11.0 13.8 14.8 80 11.0 13.8 14.8 100 11.0 13.8 14.8 200 11.0 13.8 14.8 400 11.0 13.8 14.8 500 7.72 10.2 14.8 800 5.68 7.72 10.9 1000 4.77 6.13 9.08 1500 3.41 4.01 6.13 2000 2.73 3.63 4.99 4000 1.70 2.27 3.40 6000 1.16 1.54 2.27 8000 0.84 1.14 1.66 10000 0.75 0.95 1.45 Liquids flow rate (m 3 /h) - Size 1 bag - Initial Delta-P 0.07 bar For size 2 bags multiply flow rate x 1.88 For size 3 bags multiply flow rate x 0.28 For size 4 bags multiply flow rate x 0.44 Zone Recommended Good Poor Not recommended DIMENSIONS Size 1: Dia.178 x L 419 mm Size 2: Dia.178 x L 813 mm Size 3: Dia.102 x L 203 mm Size 4: Dia.102 x L 356 mm FILTERING AREA AVAILABLE FILTRATION RATING Nylon monofilament 1, 5, 10, 25, 45, 50, 55, 70, 75, 100, 125, 150, 175, 200, 250, 300, 400, 500, 600, 800, 1000 μm Polyester monofilament 1, 5, 10, 75, 100, 125, 150, 200, 250, 300, 400 μm Polyester multifilament 100, 150, 200, 250, 300, 400, 500, 600, 800, 1000, 1500, 2000 μm Polypropylene monofilament 200, 300, 400, 600, 800 μm Size 1: 0.23 m 2 Size 2: 0.45 m 2 Size 3: 0.06 m 2 Size 4: 0.11 m 2 VOLUME Size 1: 6.8 liters Size 2: 15.1 liters Size 3: 1.3 liters Size 4: 2.3 liters Text in Bold: fiber, µm, sizes in stock.
Special Series on request: TXD-P filter bags. extended life. size 1-2-3-4 CHARACTERISTICS Extended-life needle felt construction Fibre free surface treatment Silicone oil free Approved FDA material (polypropylene and polyester) (FDA 21 CFR 176.170 and FDA 21 CFR 177.1520 3.2a) Fully thermo-welded construction Rounded bottom to fit perfectly in the restrainer basket All configurations supplied with handles for easy change out Material and filtration rating stamped on the filter media Polypropylene PolyformSEAL seal ring Stainless steel or tinned steel seal ring as option Available in two different materials Fine diameter fibres for higher void volume to increase the dirt holding capacity High thickness felt to increase the dirt holding capacity Filtering surface fully micro porous 2 to 5 times the dirt holding capacity than traditional needle felt Filtration rating from 1 to 200 μm MAIN APPLICATIONS Desalination Water treatment Fine chemical Petrochemical Oil & Gas Food & Beverage Power generation Paints and resin Pharmaceutical Microelectronic Galvanic General industry Rounded bottom: best fitting in the restrainer basket PolyformSEAL seal: 4 points positive seal for by-pass free filter bag Series TXD-P Filter bags - Extended life Extended-life: fine fibres and high thk. = high dirt holding capacity
technical data WORKING TEMPERATURE Polypropylene 93 C Polyester 135 C DIFFERENTIAL PRESSURE Bag replacement: 1.7 bar @ 25 C Max allowable: 3.5 bar @ 25 C CONSTRUCTION MATERIALS Polypropylene extended-life Polyester extended-life DIMENSIONS Size 1: Size 2: Size 3: Size 4: OD 178 x L 419 mm OD 178 x L 813 mm OD 102 x L 203 mm OD 102 x L 356 mm FILTERING AREA FLOW RATE / DELTA-P DATA Viscosity [cp] Filtration rating [µm] 1 5 10 25 100 200 1 18.0 18.0 18.0 18.0 18.0 18.0 20 11.3 18.0 18.0 18.0 18.0 18.0 30 7.72 14.5 18.0 18.0 18.0 18.0 40 6.13 10.9 15.9 18.0 18.0 18.0 60 4.77 9.08 13.6 18.0 18.0 18.0 80 3.86 6.81 10.2 17.0 18.0 18.0 100 3.18 5.45 7.72 12.5 18.0 18.0 200 1.48 2.95 4.09 6.81 9.54 12.5 400 0.84 1.57 2.72 4.01 5.68 7.04 500 0.64 1.16 1.70 2.95 4.01 5.00 800 0.45 0.82 1.25 2.04 2.95 3.86 1000 0.39 0.68 1.02 1.66 2.27 3.41 1500 0.30 0.52 0.73 1.20 1.59 2.16 2000 0.20 0.40 0.57 0.86 1.25 1.64 4000 0.14 0.27 0.36 0.61 0.79 1.09 6000 0.09 0.18 0.27 0.43 0.59 0.77 8000 0.07 0.13 0.19 0.32 0.41 0.57 10000 0.07 0.10 0.16 0.27 0.36 0.48 Liquids flow rate (m 3 /h) - Size 1 bag - Initial Delta-P 0.07 bar For size 2 bags multiply flow rate x 1.88 For size 3 bags multiply flow rate x 0.28 For size 4 bags multiply flow rate x 0.44 AVAILABLE FILTRATION RATING Polypropylene Polyester Zone 1, 3, 5, 10, 25, 50, 100, 200 μm 1, 5, 10, 25, 50, 100 μm Recommended Good Poor Not recommended Size 1: 0.23 m 2 Size 2: 0.45 m 2 Size 3: 0.06 m 2 Size 4: 0.11 m 2 VOLUME Size 1: Size 2: Size 3: Size 4: 6.8 liters 15.1 liters 1.3 liters 2.3 liters
Special Series on request: TPP-M filtering bag. microfiber. size 1-2-3-4 CHARACTERISTICS Polypropylene microfiber construction High filtration efficiency: up to 99.9% Excellent oil adsorption capacity Up to twelve different graded density layers Silicone oil free No fibre releasing FDA approved polypropylene (FDA 21 CFR 176.170 e FDA 21 CFR 177.1520 3.2a) Filter media thermo-welded to the seal ring Double and reinforced longitudinal sewn Rounded bottom to fit perfectly in the restrainer basket Material and filtration rating stamped on the filter media All configurations supplied with handles for easy change out Polypropylene PolyformSEAL seal ring Stainless steel or tinned steel seal ring as option Filtration rating from 1 to 25 μm MAIN APPLICATIONS Desalination Water treatment Fine chemical Petrochemical Oil & Gas Food & Beverage Power generation Paints and resins Pharmaceutical Microelectronic Galvanic General industry Multifilament construction: high dirt holding capacity depth filtration PolyformSEAL seal: 4 points positive seal for by-pass free filter bag Series TPP-M Filtering bag - microfiber - size 1-2-3-4 Metal ring design
technical data WORKING TEMPERATURE Polypropylene 93 C Max allowable flow rate data: Flow rate Size 1 cp 10 cp 100 cp 1000 cp 1 15.0 13.5 4.5 0.6 2 28.0 25.0 8.4 1.2 3 8.0 7.2 2.4 0.3 4 4.5 4.0 1.3 0.2 Liquid flow rate (m 3 /h) - Clean Delta-P 0.1 bar DIFFERENTIAL PRESSURE Filtering bag replacement: 1.7 bar @ 25 C Max allowable: 3.5 bar @ 25 C CONSTRUCTION MATERIALS Polypropylene microfiber EFFICIENCY / SIZE REMOVED: μm Efficiency Size removed 1 90.0% 1-2 μm 2 99.6% 2-5 μm 5 99.3% 5-10 μm 10 99.8% 10-15 μm 25 99.9% 20-30 μm DIMENSIONS AVAILABLE FILTRATION RATING Size 1: Size 2: Size 3: Size 4: OD 178 x L 419 mm OD 178 x L 813 mm OD 102 x L 203 mm OD 102 x L 356 mm 1, 2, 5, 10, 25 μm OA = Oil adsorbing OAXL = High efficiency FILTERING AREA Size 1: 0.23 m 2 Size 2: 0.45 m 2 Size 3: 0.06 m 2 Size 4: 0.11 m 2 VOLUME Size 1: Size 2: Size 3: Size 4: 6.8 liters 15.1 liters 1.3 liters 2.3 liters
Special Series on request: T-DUPLO duplo filter bags. increased filter area size 22 CHARACTERISTICS W style filter bag Designed to increase 40% at least the filtering area Without modification of the existing filter housings Reduced operating cost High dirt holding capacity Silicon oil free FDA approved materials (polypropylene and polyester) (FDA 21 CFR 176.170 and FDA 21 CFR 177.1520 3.2a) Fully thermo-welded construction Cotton handles for easy removal from the restrainer Material and filtration rating stamped on the filter media Polypropylene PolyformSEAL seal ring Stainless steel or tinned steel seal ring as option Available with all type of felts, microfiber or nylon mesh Electropolished 316L SS restrainer basket MAIN APPLICATIONS Desalination Water treatment Fine chemical Petrochemical Oil & Gas Food & Beverage Power generation Paints and resins Pharmaceutical Microelectronic Galvanic General industry Restrainer basket: conical inner support for easy removal of the filter bag PolyformSEAL seal: 4 points positive seal for by-pass free filter bag Series T-DUPLO Duplo filter bags - increased filter area - size 22 Cotton handles: easy removal of the clogged filter bag
technical data WORKING TEMPERATURE Polypropylene 93 C Polyester 135 C Nylon 135 C DIFFERENTIAL PRESSURE Bag replacement: Filter bag replacement: 0.7 to 1.3 bar @ 25 C Max. allowable: 2.41 bar @ 25 C FLOW RATE / DELTA-P DATA Felt Viscosity [cp] Filtration rating [µm] 1 5 10 25 100 200 1 33.8 33.8 33.8 33.8 33.8 33.8 20 21.2 33.8 33.8 33.8 33.8 33.8 30 14.5 27.3 33.8 33.8 33.8 33.8 40 11.5 20.5 15.9 33.8 33.8 33.8 60 9.0 17.0 13.6 18.0 33.8 33.8 80 7.25 12.8 10.2 17.0 33.8 33.8 100 6.0 10.2 14.5 23.5 33.8 33.8 200 2.78 5.55 7.69 12.8 17.9 23.5 400 1.58 2.95 5.11 7.53 10.6 13.2 500 1.20 2.18 3.19 5.55 7.54 9.40 800 0.85 1.54 2.35 3.84 5.55 7.26 1000 0.73 1.28 1.92 3.12 4.27 6.41 1500 0.56 0.98 1.37 2.26 2.99 4.06 2000 0.38 0.75 1.07 1.62 2.25 3.08 4000 0.62 0.50 0.68 1.15 1.49 2.05 6000 0.17 0.33 0.50 0.80 1.11 1.45 8000 0.13 0.24 0.36 0.60 0.77 1.07 10000 0.07 0.19 0.30 0.50 0.68 0.90 Viscosity [cp] Monofilament Filtration [μm] 150-250 300-600 600-800 1 20.7 26.0 28.0 20 20.7 26.0 28.0 30 20.7 26.0 28.0 40 20.7 26.0 28.0 60 20.7 26.0 28.0 80 20.7 26.0 28.0 100 20.7 26.0 28.0 200 20.7 26.0 28.0 400 20.7 26.0 28.0 500 14.5 10.2 28.0 800 10.7 19.2 20.4 1000 8.97 11.5 17.1 1500 6.41 7.54 11.5 2000 5.13 6.82 9.38 4000 3.20 4.27 6.40 6000 2.18 2.90 4.27 8000 1.58 2.14 3.12 10000 1.41 1.79 2.73 Liquid flow rate (m 3 /h) - Size 1 bag 22 - Initial Delta-P 0.07 bar CONSTRUCTION MATERIALS Felts: Polypropylene Polyester Size Flow rate 1 cp 10 cp 100 cp 1000 cp 1 15.0 13.5 4.5 0.6 2 28.0 25.0 8.4 1.2 3 8.0 7.2 2.4 0.3 Zone Recommended Good Poor Not recommended Monofilament: 4 4.5 4.0 1.3 0.2 Nylon Liquid flow rate (m3/h) - Clean Delta-P 0.1 bar Microfiber: Polypropylene AVAILABLE FILTRATION RATING DIMENSIONS Size 22: OD 178 x L 813 mm Duplo design Polypropylene felt 1, 3, 5, 10, 25, 50, 100, 200 μm Polyester felt 1, 5, 10, 25, 50, 100 μm Nylon monofilament 1, 5, 10, 25, 45, 50, 55, 70, 75 100, 125, 150, 175, 200, 250, 300, 400, 500, 600, 800, 1000 μm Polypropylene microfiber 1, 2, 5, 10, 25 μm FILTERING AREA Size 22: 0.7 m² (std W basket) 0.9 m² (W star basket) VOLUME Size 22: 11.6 liters
ITALY FRANCE U.A.E. U.S.A. Testori S.p.A. Group Headquarters Largo A. Testori, 5 20026 Novate Milanese (MI) Italy Tel. +39 02 3523 1 Fax +39 02 3523 230 info@testori.it www.testori.it For Middle East contact: For France, Belgium, Benelux contact: Testori Emirates - Filtration Factory LLC P.O. Box 41522 Abu Dhabi - Musaffah U.A.E. Tel. +971 508 504 668 sales@testoriemirates.com mrovelli@testoriemirates.com TTL France S.A. 2 rue Paul-Henri Spaak - BP n 9 68391 Sausheim Cedex - France Tel. +33 389 312 231 Fax +33 389 619 225 info@ttlfrance.fr briefinglab.com