HANDSET WALL FORM Quick Assembly - can be built using only a hammer Reduced weight increases productivity Unsurpassed flexibility in design and availability of panels for a wide variety of applications High pour rate of 1200 psi with a safety factor of 2:1 Handset Wall Form Superior strength to weight ratio Simplicity and efficiency coupled with high strength and versatility best describes the Handset Forming System. A popular forming option with both repeat and first time users, the ease with which the system can be built along with its inherent strength continue to make Handset forming one of the most cost and labor effective solutions available to the contractor. ATLAS-SALES.COM (808) 841-1111
Best Strength to Weight Ratio HANDSET PATENT 8-0 head (1200 psi) SYMONS 6-8 head (1000 psi) 10 20 30 40 50 60 70 80 90 100 110 120 130 HANDSET 58 lb. (26.30kg) SYMONS 75 lb. (34.02kg) PATENT 86 lb. (39.00kg) NOTE: Pressure base on ACI Committee 347 formulas and manufacturers printed rating with wall ties 2-0 on center. The latest combination of alluminum alloys and forming technology means faster pour rates and increased labor savings. In addition, the above comparisons do not illustrate the further advantage of the Handset system s 2:1 safety factor. Standard Panels and Fillers - 75 Sizes in Stock 8 6 5 4 3 30 (762mm) 24 (610mm) 22 (559mm) 20 (508mm) 18 (457mm) 16 (406mm) 14 (356mm) 12 (305mm) 10 (254mm) 8 (203mm) 6 (152mm) 4 (102mm) 2 (51mm) 1.5 (38mm) 1 (25mm) Aluminum Frame - Plywood Face 2 BUILDING HAWAII SINCE 1961
Handset Diagram DOUBLE 2x4 WALER 30 x 4-0 FILLER 20 x 4-0 FILLER GUARD RAIL SCAFFOLD PLANK WALKWAY BRACKET LOOP TIE 24 x4-0 BRACE PLATE STRONGBACK CLAMP ASSEMBLY DOUBLE 2 x 4 STRONGBACK K-30 KEY 24 x 8-0 20 x 8-0 FILLER 2 x 4 BASE PLATE DOUBLE 2 x 4 STRONGBACK WOOD BRACE WALER CLAMP ASSEMBLY TURNBUCKLE BRACE STAKE ATLAS-SALES.COM (808) 841-1111 3
Application Guide S KEYS INSIDE CORNER ALUMINUM OUTSIDE CORNER KEYS S S 1/2 x 2 FIT UP BOLTS W/ NUT 1/2 x 2-1/2 MACHINE BOLTS JOINT COLUMN LIFT ANGLE OUTSIDE CORNER ANGLE GANG LIFT BRACKET S Head of horizontal key is hit with hammer while the vertical key is pressed in by hand. JOINT TIE 2 1 TIE INSTALLATION (FLAT OR LOOP TIE) KEYS SECURING TIES 4 BUILDING HAWAII SINCE 1961
Application Guide HANDSET OPTIONAL CONNECTION 1/2 x 2 FIT UP BOLT W/ NUTS S KEYS KEYS KEY INSTALLATION PILASTER FORM NAIL SHORTSTOP S 3/4 PLYWOOD KEYS FLAT TIE KEYS 2 x 4 WALERS JOINT WALER CLAMP ALUMINUM PLYWOOD FILLER ANGLE 14 Max width of plywood without stiffeners S S NAILS, SCREWS OR BOLTS ALSO AVAILABLE TO FIT A 2 x 4 WALER AND 2x 6 STRONGBACK 2 x 4 WALER STRONGBACK CLAMP 2 x 4 STRONGBACK KEY BOLT WALKWAY BRACKET ATLAS-SALES.COM (808) 841-1111 5
HANDSET S Description Item No. Weight 30 ALUMNIUM S Available in 30 x3, 30 x4, 30 x6 and 30 x8 24 ALUMNIUM S Available in 24 x3, 24 x4, 24 x5, 24 x6 and 24 x8 22 ALUMNIUM S Available in 22 x3, 22 x4, 22 x6 and 22 x8 20 ALUMNIUM S Available in 20 x3, 20 x4, 20 x5, 20 x6 and 20 x8 18 ALUMNIUM S Available in 18 x3, 18 x4, 18 x6 and 18 x8 16 ALUMNIUM S Available in 16 x3, 16 x4, 16 x5, 16 x6 and 16 x8 14 ALUMNIUM S Available in 14 x3, 14 x4, 14 x6 and 14 x8 12 ALUMNIUM S Available in 12 x3, 12 x4, 12 x6 and 12 x8 10 ALUMNIUM S Available in 10 x3, 10 x4, 10 x6 and 10 x8 8 ALUMNIUM S Available in 8 x3, 8 x4, 8 x6 and 8 x8 6 ALUMNIUM S Available in 6 x3 and 6 x6 4 ALUMNIUM S Available in 4 x4, 4 x6 and 4 x8 The main forming component of the handset system. Alumnium panels are light weight and provide an excellent strenght to weight ratio. Plywood is 5/8 HDO. Panels attach to one another and are held in place with keys or bolts and plumbed with 2x4 walers and 2x4 or 2x6 strongbacks. 6 BUILDING HAWAII SINCE 1961
ACCESSORIES Description Item No. HANDSET Weight 2 STEEL FILLERS Available in 2 x3, 2 x4, 2 x6 and 2 x8 1.5 STEEL FILLERS Available in 1.5 x3, 1.5 x4 and 6 x6 1 STEEL FILLERS Available in 1 x3, 1 x4, 1 x6, 1 x8 Added to aluminum panels when the wall size required is larger than a standard panel layout. Best applied between panels rather than at the ends or corners. FILLER ANGLES 1 FILLER ANGLE HS521 1 LB 2 FILLER ANGLE HS522 2 LB 3 FILLER ANGLE HS523 3 LB 4 FILLER ANGLE HS524 4 LB 6 FILLER ANGLE HS526 6 LB 8 FILLER ANGLE HS528 8 LB Holds 3/4 plywood in place of aluminum panels when cutouts or access is required. Also installed in large runs to aids in the beginning of stripping the wall form. Maximum plywood width (between aluminum frames) is determined by pressure/heigh of pour. 14 Maximum width of plywood without stiffeners. PILASTER FORMS ATLAS-SALES.COM (808) 841-1111 3 PILASTER FORM HS533 34 LB 4 PILASTER FORM HS534 47 LB 5 PILASTER FORM HS535 59 LB 6 PILASTER FORM HS536 71 LB 8 PILASTER FORM HS538 95 LB To create pilasters which vary from 1-12 inches. Two pilaster form units form flanges on either side of the pilaster and are held together with standard panels and fillers. Depending on the desired depth of the pilaster, the form can be installed one way to accomodate odd depths (1, 3 5, 7, 9 and 11 inches) or turned over for even depts of (2, 4, 6, 8, 10 and 12 inches) 7
HANDSET ACCESSORIES Description Item No. Weight K-30 KEY (SHORT) HS900.2 LB The main connecting component for aluminum panels. Because the K-30 Key is used to join and wedge aluminum panels it is often referred to as a 2 key system. A nail hole is provided for shortstopping, effectively shortening the length of the key allowing the user to tighten the joint. K-28 KEY (LONG) HS903 1.65 LB d to connect steel fillers to aluminum panels and held in place with the Wedge W-7. Because the K-28 Key is used in conjunction with the Wedge W-7 it is often referred to as a key and wedge system. The two nail holes on the K-28 Key (long key) provide for shortstopping when connecting steel fillers, allowing the user to tighten the joint for 1 1/2 and 1 fillers. WEDGE W-7 HS906.2 LB Combines with the K-28 Key to connect steel fillers to aluminum panels. Also used in situations where the K-30 Key (when used vertically as a wedge) will not tighten the joint. FIT-UP BOLT AND NUT FIT-UP BOLT 1/2 x2 HX916.2 LB FIT-UP NUT 1/2 HX932.04 LB 8 d to connect aluminum panels in place of keys, column lift angles to corners of column form, hinges to column forms and the brace plate to aluminum panels. Often used in colum form applications where a hinged form is created and used for multiple pours. Assures a solid joint for the hinged form when being moved by a crane. BUILDING HAWAII SINCE 1961
ACCESSORIES Description Item No. HANDSET Weight BRACE PLATE HX864 2 LB Allows a 2x4 brace to be attached to the aluminum panels. Combines with Form Aligner Brace and 2x4 for plumbing. Installed by nailing or bolting to a 2x4 and secured to the side rail of the aluminum panel with key and wedge or fit-up bolt in the large hole. FORM ALIGNER BRACE 21105 8 LB Nails to 2x4 brace and is staked into the ground on the bent plate side allowing for plumbing of the wall, column or beam. Commonly referred to as a turnbuckle brace the Form Aligner Brace has a 5-1/2 adjustable length; when closed the length is 38-1/2 and 44 when open. COLUMN LIFT ANGLE HX716 6 LB Connects to the outside corner of a column form for lifting with a crane. Attaches with fit up nut and bolt and are placed in pairs diagonally on a column form for lifting with a crane. Each angle is rated at 1000 lbs. lifting load with a 4:1 safety factor, based on the ultimate strength of the steel plate. COLUMN CADDY HS969 160 LB Assists in the moving of large columns. Column caddy is positioned at the hinged corner of the column so when stripped, the column can be placed onto the caddy such that the open end faces outward allowing it to be moved to the next position. ATLAS-SALES.COM (808) 841-1111 9
HANDSET ACCESSORIES Description Item No. Weight GANG FORM LIFT BRACKET HS935 4 LB d to lift ganged panels. 2,000 lb vertical lifting capacity CHAMFER FORM 6 x8 HS486 91 LB d for 45% chamfored corners. Connects to aluminum panels with keys. FORM EXTENSION BRACKET HS966 3 LB Extends vertical height of the top of forms. Often used for rebar rising from poured wall and ending at a right angle to accomodate for the pouring of a floor. Maximum height above top of form is 12. WALKWAY BRACKET HS923 13 LB Connects to aluminum fram to allow for a walkway at a desired height. Usually installed near the top of a form to allow work access. Must be installed every 8. 10 BUILDING HAWAII SINCE 1961
ACCESSORIES Description Item No. HANDSET Weight WALER CLAMPS WALER CLAMP 2x4 HS912 1.4 LB WALER CLAMP 2x6 HS913 1.5 LB Fastens 2x4 or 2x6 waler (horizontal supports) to aluminum frames. Must be applied to every other joint. STRONGBACK CLAMP 2x4 HS916 1.5 LB Fastens 2x4 or 2x6 strongback (vertical support) to 2x4 walers. Must be connected at each waler crossing with a maximum distance between strongback clamps of 8. WALER ROD ASSEMBLY WALER ROD 10 x1/2 HS945.6 LB WALER ROD 14 x1/2 HS948.7 LB WALER PLATE 1/4 x2 x5 HS951.73 LB COIL HANDLE NUT 1/2 HS938.3 LB Adjustable waler connector when larger or heavier strongback is required. Most applications will use the standard waler clamps. ATLAS-SALES.COM (808) 841-1111 11
HANDSET CORNERS Description Item No. Weight OUTSIDE CORNERS Available in 3, 4, 5, 6 and 8 Connects two aluminum panels to create the outside corner of a 90 joint. Connects to panels with keys or fit-up bolts. INSIDE CORNERS Available in 6 x6 x 3, 4, 5, 6 and 8 Connects two aluminum panels to create the inside corner of a 90 joint. Connects to panels with keys or fit-up bolts. OUTSIDE CORNERS 135 Available in 6 x6 x 3, 4, 5, 6 and 8 Connects two aluminum panels to create the outside corner of a 135 joint. Connects to panels with keys or fit-up bolts. INSIDE CORNERS 135 Available in 4, 6 and 8 Connects two aluminum panels to create the inside corner of a 135 joint. Connects to panels with keys or fit-up bolts. 12 BUILDING HAWAII SINCE 1961
CORNERS Description INSIDE HINGED CORNERS Available in 8 6 and 2 6 Item No. HANDSET Weight Connects to aluminum panels to create the inside corner of a variety of angles other than the 90 and 135. Connects to panels with keys or fit-up bolts. OUTSIDE HINGED CORNERS Available in 3, 6 and 8 Connects to aluminum panels to create the outside corner of a variety of angles other than the 90 and 135. Connects to panels with keys or fit-up bolts. ATLAS-SALES.COM (808) 841-1111 13
PURCHASE ONLY ACCESSORIES Description Item No. Weight LOOP TIES Available in.262 DIA x 4-36 lenghts d to position aluminum panels a specific distance apart and to withstand lateral pressure created by concrete poured between the forms. Held in place with keys. Vertical form joints must be opposing and ties are required at every form joint. When concrete is set the loop tie ends are knocked off with a hammer. Loop ties are for purchase only. FLAT TIES Available in 10 GA 4-24 lenghts d to position aluminum panels a specific distance apart and to withstand lateral pressure created by concrete poured between the forms. Held in place with keys. d in place of loop ties. Flat ties are for purchase only. BASE TIES Available in.225 DIA x 6-24 lenghts d to create grade beams. Simplifies work by replacing traditional loop ties and placing one base tie at the top and bottom of the form when panels are run horizontally. Held in place with keys. Base ties are for purchase only. 14 BUILDING HAWAII SINCE 1961
ROUND COLUMN FORM Description ALUMNIUM ROUND COLUMN FORM Available in 14 DIA x 2 8, 4 and 8 Available in 18 DIA x 1, 2 and 8 Available in 24 DIA x 1, 2, 3, 4 and 8 Available in 26 DIA x 1, 2, 4 and 8 Available in 28 DIA x 8 Item No. HANDSET Weight Half of the column is built with the selected diameter to the desired height and then paired with an identical construction of forms to create the column. Joints of the forms are secured with fit-up bolts. Flanges on outside of forms allow for crane rigging assisting in placement of the column forms. Due to size of holes the use of a 5/8 flat washer is required. ATLAS-SALES.COM (808) 841-1111 STEEL ROUND COLUMN FORM Available in 12 DIA x 2 and 8 (HS) Available in 18 DIA x 1 Available in 22 DIA x 2, 8 and 9 6 Available in 24 DIA x 2, 8 (HS) Available in 27 DIA x 1, 2, 4 and 8 Available in 28 DIA x 4 Available in 30 DIA x 2 and 8 (HS) Available in 32 DIA x 4 and 8 Available in 33 DIA x 2, 8 and 10 Available in 36 DIA x 1, 9 6 and 12 Available in 36 DIA x 2, 4 and 8 (HS) Half of the column is built with the selected diameter to the desired height and then paired with an identical construction of forms to create the column. Joints of the forms are secured with fit-up bolts. Flanges on outside of forms allow for crane rigging assisting in placement of the column forms. Due to size of holes the use of a 5/8 flat washer is required. Forms with the (HS) designation at the end of their description can be used in wall form applications to creat bullnosed ends. Holes in those forms align with those on the aluminum handset panels. 15
ROUND COLUMN FORM Description Item No. Weight FIT-UP BOLT AND NUT FIT-UP BOLT 5/8 x2 3301350.2 LB FIT-UP NUT 5/8 3301360.04 LB d to connect the vertical pieces of the column form together and to join the two mirrored forms together to complete the cylindrical form. The fit-up bolt and nut for round column forms and to attach round column forms to handset panels is 5/8 rather than 1/2. FORM ALIGNER BRACE 21105 8 LB Allows for plumbing of the column. Commonly referred to as a turnbuckle brace the Form Aligner Brace has a 5-1/2 adjustable length; when closed the length is 38-1/2 and 44 when open. Two options for the use of the form aligner brace are 1) a single unit attaches to the top collar of the column form and then is attached to a 2x4 that is driven into the ground, 2) 2 form aligner braces are used, one at each end of the 2x4, one bolted to the top collar of the column form and the other staked into the ground 16 BUILDING HAWAII SINCE 1961