ETA-Danmark A/S Göteborg Plads 1 DK-21590 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet ww.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011 of the European Parliament and of the Council of 9 March 2011 MEMBER OF EOTA European of 11/12/2014 I General Part Body issuing the ETA and designated according to Article 29 of the Regulation (EU) No 305/2011: ETA-Danmark A/S Trade name of the construction product: RESINE EP for rebar connections Product family to which the above construction product belongs: Manufacturer: Manufacturing plant: This European Technical Assessment contains: Post-installed rebar connections of the sizes 8 to 32 mm with RESINE EP injection mortar I.N.G. Fixations BP 168 Z. I. de Chassende F-43005 Le Puy-En-Velay Cedex Tel. +33 4 71 05 59 03 Fax +33 4 71 04 07 20 I.N.G. Fixations Manufacturing Plant I 25 pages including 20 annexes which form an integral part of the document This European Technical Assessment is issued in accordance with Regulation (EU) No 305/2011, on the basis of: This version replaces: Guideline for European Technical Approval (ETAG) No. 001 Metal Anchors for use in concrete, Part 5 Bonded anchors, April 2013, used as European Assessment Document (EAD).
Page 2 of 25 no., issued on 2014-12-11 Translations of this European in other languages shall fully correspond to the original issued document and should be identified as such. Communication of this European Technical Assessment, including transmission by electronic means, shall be in full (except the confidential Annexes referred to above). However, partial reproduction may be made, with the written consent of the issuing Body. Any partial reproduction has to be identified as such.
Page 3 of 25 no., issued on 2014-12-11 II SPECIFIC PART OF THE EUROPEAN TECHNICAL ASSESSMENT 1 Technical description of product and intended use Technical description of the product The subject of this assessment are the post-installed connections, by anchoring or overlap connection joint consisting of steel reinforcing bars (rebars) in existing structures made of normal weight concrete, using injection mortar RESINE EP in accordance with the regulations for reinforced concrete construction. The design of the post-installed rebar connections shall be done in accordance with EN 1992-1-1 (Eurocode 2). Reinforcing bars with diameters from 8 to 32 mm and RESINE EP injection mortar according to Annex A3 are used for the post-installed rebar connections covered by this ETA. The steel element is placed into a drilled hole previously injected with a mortar and is anchored by the bond between embedded element, injection mortar and concrete. The characteristic material values, dimensions and tolerances of the anchors not indicated in Annexes shall correspond to the respective values laid down in the technical documentation 1 of this European Technical Assessment. Each mortar cartridge is marked with the identifying mark of the producer and with the trade name. The rebars are either delivered with the mortar cartridges or commercial standard rebars purchased separately. The RESINE EP injection mortar is delivered in mortar cartridges in a difference sizes in accordance with Annex A4. For the installed anchor see Figure given in Annex A2. The intended use specifications of the product are detailed in the Annex B1. 2 Specification of the intended use in accordance with the applicable EAD The post-installed rebar connections may be used in normal weight concrete of a minimum grade C12/15 and maximum grade C50/60 according to EN 206-1. They 1 The technical documentation of this European Technical Assessment is deposited at ETA-Danmark and, as far as relevant for the tasks of the Notified bodies involved in the attestation of conformity procedure, is handed over to the notified bodies. may be used in non-carbonated concrete with the allowable chloride content of 0,40 % (Cl 0,40) related to the cement content according to EN 206-1 The rebar connections may be used for predominantly static loads. Fatigue, dynamic or seismic loading of post-installed rebar connections are not covered by this ETA. The fire resistance of the post-installed rebar connections is not covered by this ETA. The rebar connections may only be carried out in the manner, which is also possible with reinforcing bars, e.g. those in the following applications: - an overlapping joint with existing reinforcement in a building component (Figures 1 and 2, Annex A1), - anchoring of the reinforcement at a slab or beam support (Figure 3, Annex A1; end support of a slab, designed as simply supported, as well as appropriate reinforcement for restraint forces), - anchoring of reinforcement of building components stressed primarily in compression (Figure 4, Annex A1), - anchoring of reinforcement to cover the line of acting tensile force (Figure 5, Annex A1). The post-installed rebar connections may be used in dry or wet concrete and it must not be installed in flooded holes. The post-installed rebar connections may be used overhead. The post-installed rebar connections may be used in the temperature range -40 C to +80 C (max. short term temperature +80 C and max. long term temperature +50 C). This ETA covers anchoring in bore holes made with hammer drilling and diamond drilling technique (wet and dry cutting system). The performances given in Section 3 are only valid if the anchor is used in compliance with the specifications and conditions given in Annex B1 to B12 The provisions made in this European Technical Assessment are based on an assumed intended working life of the anchor of 50 years. The indications given on the working life cannot be interpreted as a guarantee given by the producer or Assessment Body, but are to be regarded only as a means for choosing the right products in relation to the expected economically reasonable working life of the works.
Page 4 of 25 no., issued on 2014-12-11 3 Performance of the product and references to the methods used for its assessment 3.1 Characteristics of product Mechanical resistance and stability (BWR1): The essential characteristics are detailed in the Annex from C1 to C3. Safety in case of fire (BWR2): The essential characteristics are detailed in the Annex C1. Hygiene, health and the environment (BWR3): Regarding the dangerous substances contained in this European, there may be other requirements applicable to the products falling within its scope (e.g. transposed European legislation and national laws, regulations and administrative provisions). In order to meet the provisions of the Construction Products Regulation, these requirements need also to be complied with, when and where they apply. Safety in use (BWR4): For basic requirement Safety in use the same criteria are valid for Basic Requirement Mechanical resistance and stability (BWR1). Sustainable use of natural resources (BWR7) No performance determined Other Basic Requirements are not relevant. 3.2 Methods of assessment The assessment of fitness of the anchor for the intended use in relation to the requirements for mechanical resistance and stability and safety in use in the sense of the Basic Requirements 1 and 4 has been made in accordance with the «Guideline for European Technical Approval of Metal Anchors for use in Concrete», Part 1 «Anchors in general» and Part 5 «Bonded anchors», and EOTA Technical Report 023 Assessment of postinstalled rebar connections.
Page 5 of 25 no., issued on 2014-12-11 4 Assessment and verification of constancy of performance (AVCP) 4.1 AVCP system According to the decision 96/582/EC of the European Commission, the system(s) of assessment and verification of constancy of performance (see Annex V to Regulation (EU) No 305/2011) is 1. 5 Technical details necessary for the implementation of the AVCP system, as foreseen in the applicable EAD Technical details necessary for the implementation of the AVCP system are laid down in the control plan deposited at ETA-Danmark Issued in Copenhagen on 2014-12-11 by Thomas Bruun Managing Director, ETA-Danmark
Page 6 of 25 no., issued on 2014-12-11 Use of the product Annex A1
Page 7 of 25 no., issued on 2014-12-11 Product description Annex A2
Page 8 of 25 no., issued on 2014-12-11 Table A1: Rebar according to EN 1992-1-1, Annex C, Tables C.1 and C.2 Product form Bars and de-coiled rods Class B C Characteristic yield strength fyk or f0,2k [N/mm 2 ] 400 to 600 Minimum value of k = (ft / fy)k 1,08 Characteristic strain at minimum force, εuk [%] 5,0 7,5 Bendability Maximum deviation from nominal mass (individual bar), [%] Bond: Minimum relative rib area, fr,min Rib height h: The rib height h should be: 0,05 Ø h 0,07 Ø Ø = nominal bar diameter Table A2: Injection mortar Nominal bar size [mm] 8 > 8 Nominal bar size [mm] 8 to 12 > 12 1,15 < 1,35 Bend / Rebend test ± 6.0 ± 4.5 0,040 0,056 Product RESINE EP two components injection mortar Composition Additive: quartz Bonding agent: epoxy resin Materials Annex A3
Page 9 of 25 no., issued on 2014-12-11 Cartridge types and sizes Annex A4
Page 10 of 25 no., issued on 2014-12-11 Anchorages subject to: - Static and quasi-static loads. Base materials: Specification of intended use - Reinforced or unreinforced normal weight concrete of strength class C12/15 at minimum to C50/60 at maximum according to EN 206-1. - Maximum chloride content of 0,40% (CL 0,40) related to the cement content according to EN 206-1. - Non-carbonated concrete. Note: In case of a carbonated surface of the existing concrete structure the carbonate layer shall be removed in the area of the post-installed rebar connection with a diameter of ds + 60 mm prior to the installation of the new rebar. The depth of concrete to be removed shall correspond to at least the minimum concrete cover according to EN 1992-1-1. The above may be neglected if building components are new and not carbonated and if building components are in dry conditions. Temperature range: - - The anchors may be used in the following temperature range: -40 C to +80 C (max. short term temperature +80 C and max. long term temperature +50 C). Use conditions (Environmental conditions): - Structures subject to dry internal conditions. - Structures subject to external atmospheric exposure including industrial and marine environment). - Structures subject to permanently damp internal conditions if no particular aggressive conditions exist. Note: Particular aggressive conditions are e.g. permanent, alternating immersion in seawater or the splash zone of seawater, chloride atmosphere of indoor swimming pools or atmosphere with extreme chemical pollution (e.g. in desulphurization plants or road tunnels where de-icing materials are used). Design: - Anchorages are designed under the responsibility of an engineer experienced in anchorages and concrete work. - Verifiable calculation notes and drawings are prepared taking into account of the forces to be transmitted. - Design according to EN 1992-1-1 and Annex B2. - The actual position of the reinforcement in the existing structure shall be determined on the basis of the construction documentation and taken into account when designing. Installation: - Dry or wet concrete (use category 1). - It must not be installed in flooded holes. - Overhead installation is permissible. - Hole drilling by hammer drill and diamond drilling machine (dry and wet cutting system). - Installation of the post-installed rebars shall be done only by suitable trained installer and under supervision on the site. - Check the position of the existing rebars (if the position of existing rebars in not known it shall be determined using a rebar detector suitable for this purpose as well as on the basis of the construction documentation and then marked on the building component for the overlap joint). Intended use - Specification Annex B1
Page 11 of 25 no., issued on 2014-12-11 General design rules of construction for post-installed rebars Only tension forces in the axis of the rebar may be transmitted. The transfer of shear forces between new concrete and existing structure shall be designed additionally according to EN 1992-1-1. The joints for concreting must be roughened to at least such an extended that aggregate protrude. * If the clear distance between overlapping rebars is greater than 4 Ø the overlap length shall be enlarged by the difference between the clear distance and 4 Ø. l 0 lap length acc. to EN 1992-1-1, clause 8.7.3 l v effective embedment depth; l v l 0 + c 1 c concrete cover of post-installed rebar c min minimum concrete cover acc. to Annex B3 and EN 1992-1-1, clause 4.4.1.2. c 1 concrete cover at end-face of existing rebar d 0 nominal drill bit diameter acc. to Annex B3 Ø rebar diameter (ds) Intended use. General construction rules for post-installed rebars Annex B2
Page 12 of 25 no., issued on 2014-12-11 Table B1: Drill bit diameter and setting depth 1) Rebar diameter [mm] Ø8 Ø10 Ø12 Ø14 Ø16 Ø20 Ø25 Ø28 Ø32 HD 2) DD 3) HD 2) DD 3) HD 2) DD 3) HD 2) DD 3) Nominal drill hole d0 [mm] Min anchorage depth lb,min [mm] Min overlap joint depth l0,min [mm] Max anchorage depth lv,max [mm] 12 14 16 18 20 25 30 35 40 115 145 170 200 230 285 355 400 455 200 200 200 210 240 300 375 420 480 700 900 1100 1300 1400 1800 2200 2500 2500 1) According to EN 1992-1-1 modified with TR023: lb,min (8.6) and l0,min (8.11) with maximum yield stress for rebar BSt 500S, γm = 1,15, α6 = 1,0, concrete C20/25 with fbd = 2,30 N/mm 2 and good bond condition. 2) HD: hammer drilling method. 3) DD: diamond drilling method (dry and wet cutting system). Minimum concrete cover (see Annex B2): c min = 30 mm + 0,06 l v 2 Ø for Ø < 25 mm c min = 40 mm + 0,06 l v 2 Ø for Ø 25 mm The minimum concrete cover according to EN 1992-1-1 shall be observed. Minimum clear spacing between two post-installed rebars: a = 40 mm 4 Ø Installation data Annex B3
Page 13 of 25 no., issued on 2014-12-11 Table B2: Minimum curing time 1) Concrete temperature Processing time Minimum curing time 3) 0 C 2) 3 h 20 min 54 h 5 C 2) 2 h 30 min 41 h 10 C 1 h 40 min 28 h 15 C 1 h 10 min 22 h 20 C 50 min 16 h 25 C 30 min 14 h 30 C 20 min 12 h 1) The minimum time from the end of the mixing to the time when the anchor may be torque or loaded (whichever is longer). 2) Minimum resin temperature recommended, for injection between 5 C and 0 C, equal to 10 C. 3) Minimum curing time for dry and wet conditions. 4) Maximum resin temperature for maximum anchorage length equal to 24 C. Curing time Annex B4
Page 14 of 25 no., issued on 2014-12-11 Manual blower pump: nominal dimensions Mixer extension (from 380 mm to 1000 mm) with nominal diameter equal to 8 mm For the hole with depth grater 1000 mm up to 2500 mm it is possible use the special mixer extension (see Annex B7) for blower operation. Cleaning tools (1) Annex B5
Page 15 of 25 no., issued on 2014-12-11 Standard brush Table 7: Standard brush diameter Rebar diameter - Ø Ø8 Ø10 Ø12 Ø14 Ø16 d0 Nominal drill hole [mm] 12 14 18 18 20 db Brush diameter [mm] 14 16 20 20 22 Special brush Table 8: Special brush diameter (mechanical brush) Rebar diameter - Ø Ø8 Ø10 Ø12 Ø14 Ø16 Ø20 Ø25 Ø28 Ø32 d0 Nominal drill hole [mm] 12 14 16 18 20 25 30 35 40 db Brush diameter [mm] 14 16 18 20 22 27 32 37 42 Cleaning tools (2) Annex B6
Page 16 of 25 no., issued on 2014-12-11 Tools for injection (1) Annex B7
Page 17 of 25 no., issued on 2014-12-11 Tools for injection (2) Annex B8
Page 18 of 25 no., issued on 2014-12-11 1 Drill the hole with the correct diameter and depth using a rotary percussive machine. Check the perpendicularity of the hole during the drilling operation. 2 4x 4x 4x Blower Manual Standard Blower Manual Pump Brush Pump if necessary use a mixer extension for the blower operation (see Annex B7) Clean the hole from drilling dust: the hole shall be cleaned by at least 4 blowing operations, by at least 4 brushing operations followed again by at least 4 blowing operations; before brushing clean the brush and check (see Annex B6, standard brush) if the brush diameter is sufficient. For the blower tools see Annex B5. 3 Unscrew the front cup, screw on the mixer and insert the cartridge in the gun. 4 5 6 if necessary use a mixer extension for the injection (see Annex B7) ATTENTION: Use the rods dry and free oil and other contaminants Before starting to use the cartridge, eject a first part of the product, being sure that the two components are completely mixed. The complete mixing is reached only after that the product, obtained by mixing the two components, comes out from the mixer with an uniform color. Fill the drilled hole uniformly starting from the drilled hole bottom, in order to avoid entrapment of the air; remove the mixer slowly bit by bit during pressing-out; filling the drill hole with a quantity of the injection mortar corresponding to 2/3 of the drill hole depth. Insert immediately the rod, marked according to the proper anchorage depth, slowly and with a slight twisting motion, removing excess of injection mortar around the rod. Observe the processing time according Annex B4. Wait the curing time according Annex B4. Procedure up to 300 mm depth (hammer drilling) Annex B9
Page 19 of 25 no., issued on 2014-12-11 1 Drill the hole with the correct diameter and depth using a rotary percussive machine. Check the perpendicularity of the hole during the drilling operation. 2 3 4 x 5 seconds 4x 4 x 5 seconds ATTENTION: compressed air free oil Clean the hole from drilling dust: the hole shall be cleaned by at least 4 blowing operations (5 seconds for single operation) with compressed air, by at least 4 brushing operations with special brush followed again by at least 4 blowing operations (5 seconds for single operation) with compressed air. Before brushing clean the brush and check (see Annex B6, special brush) if the brush diameter is sufficient. For the blower tools see the Annex B5. Unscrew the front cup of the cartridges, screw on the mixer and insert the cartridge in the proper pneumatic-pump. 4 5 6 ATTENTION: Use the rods dry and free oil and other contaminants Before starting to use the cartridge, eject a first part of the product, being sure that the two components are completely mixed. The complete mixing is reached only after that the product, obtained by mixing the two components, comes out from the mixer with an uniform color. Before starting the injection, assemble the system according to Annex B7. After that, fill the drilled hole uniformly from the drilled hole bottom, in order to avoid entrapment of the air; remove the special mixer extension with injection plug slowly bit by bit during pressingout; filling the drill hole with a quantity of the injection mortar corresponding to 2/3 of the drill hole depth. Procedure for overhead application is detailed in Annex B12. Insert immediately the rod, marked according to the proper anchorage depth, slowly and with a slight twisting motion, removing excess of injection mortar around the rod. Observe the processing time according Annex B4. Wait the curing time according Annex B4. Procedure up to max anchorage depth (hammer drilling) Annex B10
Page 20 of 25 no., issued on 2014-12-11 1 Drill the hole with the correct diameter and depth using a core drill machine. Check the perpendicularity of the hole during the drilling operation. Remove completely the core from the hole. After operation 1, if the diamond drilling machine used has a dry cutting system to proceed with the installation procedure according to the point 2. Instead if it is used a wet cutting system before of the point 2 the following operation must be done: - flush hole 2 times by inserting a water hose to the back of the hole until water runs clear; - brush 2 times with the proper special brush. Before brushing clean the brush and check (see Annex B6, special brush) if the brush diameter is sufficient; - flush again 2 times until water runs clear; - remove all standing water completely (using for example vacuum system or compressed air free oil). 2 4 x 5 seconds 6x 4 x 5 seconds ATTENTION: compressed air free oil Clean the hole from drilling dust: the hole shall be cleaned by at least 4 blowing operations (5 seconds for single operation) with compressed air, by at least 4 brushing operations with special brush followed again by at least 4 blowing operations (5 seconds for single operation) with compressed air. Before brushing clean the brush and check (see Annex B6, special brush) if the brush diameter is sufficient. For the blower tools see the Annex B5. After the operation above, to follow the operations from 3 to 6 on the previous Annex B9 and B10 in function of the depth of the hole. Procedure with diamond drilling (wet and dry) for all depths Annex B11
Page 21 of 25 no., issued on 2014-12-11 Overhead application Annex B12
Page 22 of 25 no., issued on 2014-12-11 Table C1: Design values of the ultimate bond resistance f bd according to EN 1992-1-1 ESSENTIAL CHARACTERISTICS * Design bond strength fbd according to EN 1992-1-1 [N/mm 2 ] for perforation with hammer drilling machine PERFORMANCE C12/15 C16/20 20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60 da Ø8 a Ø28 1,60 2,00 2,30 2,70 3,00 3,40 3,70 4,00 4,30 Ø32 1,60 2,00 2,30 2,70 3,00 3,40 3,70 4,00 4,00 * Design bond strength fbd according to EN 1992-1-1 [N/mm 2 ] for perforation with diamond drilling machine (dry and wet cutting system) C12/15 C16/20 20/25 C25/30 C30/37 C35/45 C40/50 C45/55 C50/60 da Ø8 a Ø25 1,60 2,00 2,30 2,70 3,00 3,40 3,70 4,00 4,30 Ø28 1,60 2,00 2,30 2,70 3,00 3,40 3,70 3,70 3,70 Ø32 1,60 2,00 2,30 2,70 3,00 3,00 3,00 3,00 3,00 * Values valid only for good bond condition according to EN 1992-1-1. For other bond conditions multiply the values for 0,7 Table C2: Resistance to fire HARMONIZED TECHNICAL SPECIFICATION: ETAG 001 PART 1 PARAGRAPH 5.2.2 AND TECHNICAL REPORT TR020 ESSENTIAL CHARACTERISTICS Resistance to fire PERFORMANCE NPD Table C3: Reaction to fire HARMONIZED TECHNICAL SPECIFICATION: ETAG 001 PART 1 PARAGRAPH 5.2.1 ESSENTIAL CHARACTERISTICS Reaction to fire PERFORMANCE In the final application the thickness of the mortar layer is about 1 to 2 mm and most of the mortar is material classified class A1 according to EC Decision 96/603/EC. Therefore it may be assumed that the bonding material (synthetic mortar or a mixture of synthetic mortar and cementitious mortar) in connection with the metal anchor in the end use application do not make any contribution to fire growth or to the fully developed fire and they have no influence to the smoke hazard. Performance for static and quasi-static loads: Resistances Annex C1
Page 23 of 25 no., issued on 2014-12-11 Design Values for anchoring connection Annex C2
Page 24 of 25 no., issued on 2014-12-11 Design Values for anchoring connection Annex C3
Page 25 of 25 no., issued on 2014-12-11 TERMINOLOGY AND SYMBOLS Ø Nominal diameter of the reinforced bar d0 Drill hole diameter lv Setting depth a Minimum clear spacing between two post-installed rebar Cmin Minimum concrete cover lb,min Minimum anchorage length l0,min Minimum overlap joint length lb,rqd Required basic anchorage length NPD No declared performance RESINE EP Terminology and symbols Annex C4