Promotional Advertising White Opaque Vinyl - Removable Self-adhesive film is an essential tool for indoor and outdoor promotional advertising, providing the durability, flexibility, and aesthetic quality that open up all kinds of possibilities for grabbing the consumer s attention for the duration of the advertising campaign. End-Use Applications: Cooler Graphics Counter Graphics Display Graphics General-Purpose Signage Indoor Floor Graphics Interior Signage Shelf Graphics Wall Graphics Window Graphics For more information on FLEXcon's pressure-sensitive film solutions for Promotional Advertising, contact your local Sales Representative or our Product Branding Business Team at (508) 885-8370. Product ID #: FLX059985 Product: Benefits: 3.5 mil flexible opaque white vinyl provides good opacity for covering up existing graphics High-performance removable adhesive bonds well to ABS, acrylic, aluminum, stainless steel, HDPE, painted metal, styrene, painted non-vinyl wallboard, glass, certain ceramic tile, sealed concrete, linoleum, and Formica High-performance removable adhesive offers clean removability for up to 180 days Printable via UV and solvent screen, UV and solvent inkjet, and UV offset This image is an example of how FLEXcon products may be used FLEXmark WR HP Latex compatible 90 lb. polycoated layflat release liner for ease of converting Base film for floor graphic applications when used as a system with FLEXmark CP overlaminating film - meets industry standards for non-slip performance (UL 410) Formica is a registered trademark of the Diller Corp. Last Modified On: Dec 1 2014 12:00AM
FLEXmark WR PRODUCT DATA VALUE TEST METHOD Physical Properties Thickness (Mils[microns]) Film 3.5 (89) +/- 10% ASTM D 3652 (Modified for use with Adhesive 0.8-0.9 (20-23) +/- 0.1 (3) non-tape products) Liner 6.9 (175) +/- 10% Dimensional Stability (%) MD 0.75 Applied Shrinkage: 24 hour dwell time on TD 0.50 aluminum panel then 24 hours at 160 F (71 C) Adhesion Properties Ultimate Peel from Average ASTM D 903 (Modified for 72 hour dwell Oz/In (N/m) time) ABS 17 (187) Aluminum 17 (187) Ceramic Tile 22 (242) Formica 7 (77) Glass 19 (209) HDPE 5 (55) Linoleum 9 (99) Painted Metal 18 (198) Painted Wood 12 (132) Plexiglass 24 (264) Sealed Concrete 12 (132) Sintra 18 (198) Smooth Painted (non-vinyl) Wallboard 8 (88) Stainless Steel 22 (242) Styrene 18 (198) Varnished Wood 13 (143) Expected Shear Room Temp (hours) Erratic shear due to removable adhesive ASTM D 3654 Method A a. 1 hr. dwell b. 1 sq. in. surface c. 4 lb. load Tack (gm/sq cm) 350 ASTM D 2979 Expected Exterior Life Service Temperature Range Minimum Application Temperature Storage Stability Two years -20 F to 176 F (-29 C to 80 C) 50 F (10 C) Two years when stored at 70 F (21 C) and 50% relative humidity Product Performance and Suitability All of the descriptive information, the typical performance data, and recommendations for the use of FLEXcon products shall be used only as a guide and do not reflect the specification or specification range for any particular property of the product. Furnishing such information is merely an attempt to assist you after you have indicated your contemplated use and shall in no event constitute a warranty of any kind by FLEXcon. All purchasers of FLEXcon products shall be responsible for independently determining the suitability of the material for the purpose for which it is purchased. No distributor, salesman, or representative of FLEXcon is authorized to give any warranty, guaranty, or make any representation in addition or contrary to the above. Last Modified On: 12/21/2015
Promotional Advertising Clear Vinyl - Permanent Self-adhesive film is an essential tool for indoor and outdoor promotional advertising, providing the durability, flexibility, and aesthetic quality that open up all kinds of possibilities for grabbing the consumer s attention for the duration of the advertising campaign. End-Use Applications: Cooler Graphics Counter Graphics Display Graphics General-Purpose Signage Indoor Floor Graphics Interior Signage Outdoor Signage Wall Graphics Window Graphics For more information on FLEXcon's pressure-sensitive film solutions for Promotional Advertising, contact your local Sales Representative or our Product Branding Business Team at (508) 885-8370. Product ID #: FLX059980 Product: Benefits: 4.0 mil hard clear vinyl provides durability for ease of installation and removal Printable via UV and solvent screen, UV and solvent inkjet, and UV offset HP Latex compatible This image is an example of how FLEXcon products may be used FLEXmark CP High-performance permanent adhesive bonds well to ABS, acrylic, Formica, aluminum, stainless steel, HDPE, painted metal, styrene, painted non-vinyl wallboard, glass and more 90 lb. polycoated layflat release liner for ease of converting Overlaminate for floor graphic applications when used as a system with FLEXmark CR, CRT, WR, and WRT base films - meets industry standards for non-slip performance (UL 410) *Formica is a registered trademark of the Diller Corp. Last Modified On: Dec 1 2014 12:00AM
FLEXmark CP PRODUCT DATA VALUE TEST METHOD Physical Properties Thickness (Mils[microns]) Film 3.5 (89) +/- 10% ASTM D 3652 (Modified for use with Adhesive 0.9-1.0 +/- 0.1 (3) non-tape products) Liner 6.9 (175) +/- 10% Dimensional Stability (%) MD 0.75 Applied Shrinkage: 24 hour dwell time on TD 0.50 aluminum panel then 24 hours at 160 F (71 C) Adhesion Properties Ultimate Peel from Average ASTM D 903 (Modified for 72 hour dwell Oz/In (N/m) time) ABS 110 (1210) Acrylic Powder Paint 101 (1111) Aluminum 73 (803) Formica 48 (528) Glass 96 (1056) HDPE 41 (451) Painted Metal 90 (990) Painted Wood 35 (385) Plexiglass 121 (1331) Polycarbonate 91 (1001) Polypropylene 43 (473) Sintra 65 (715) Smooth Painted (non-vinyl) Wallboard 25 (275) Stainless Steel 87 (957) Styrene 73 (803) Varnished Wood 45 (495) Expected Shear Room Temp (hours) 15 ASTM D 3654 Method A a. 1 hr. dwell b. 1 sq. in. surface c. 4 lb. load Tack (gm/sq cm) 1000 ASTM D 2979 Expected Exterior Life Service Temperature Range Minimum Application Temperature Storage Stability One year -40 F to 176 F (-40 C to 80 C) 50 F (10 C) Two years when stored at 70 F (21 C) and 50% relative humidity Product Performance and Suitability All of the descriptive information, the typical performance data, and recommendations for the use of FLEXcon products shall be used only as a guide and do not reflect the specification or specification range for any particular property of the product. Furnishing such information is merely an attempt to assist you after you have indicated your contemplated use and shall in no event constitute a warranty of any kind by FLEXcon. All purchasers of FLEXcon products shall be responsible for independently determining the suitability of the material for the purpose for which it is purchased. No distributor, salesman, or representative of FLEXcon is authorized to give any warranty, guaranty, or make any representation in addition or contrary to the above. Last Modified On: 12/21/2015
FLEXcon s Warranty & Limited Remedy Policy for Graphic Advertising for Floors and Indoor Carpets This warranty is made in lieu of any and all other express or implied warranties, including any implied warranty of merchantability. FLEXcon warrants that its Systems for Graphic Advertising for Floors and Indoor Carpets, constructed using only FLEXcon overlaminate films, marking films, and produced and installed in accordance with FLEXcon's written instructions, will for a period of six (6) months after application; (i) maintain quality excepting ordinary and expected wear and tear: and (ii) will adhere to FLEXcon's recommended surfaces and be removable without damage to the surface*. FLEXcon will replace or refund the price of such quantity of FLEXcon Graphic Advertising for Floors and Indoor Carpets films found not to meet this warranty. The warranty is exclusive. In no case shall FLEXcon be liable for any other direct or indirect damages or loss, including without limitation any incidental, special, or consequential damages, or any labor charges incident to the removal or replacement of Graphic Advertising for Floors and Indoor Carpets. This warranty and limited remedy does not limit or exclude any claims for personal injury allegedly caused by the negligence of FLEXcon Co. Inc. *For indoor carpets, it is normal for adhesive residue to remain on the application surface when the graphic is removed, and shadowing/staining may occur. 1 FLEXcon Industrial Park, Spencer, MA 01562-2642 USA Tel +1 (508) 885-8200 www.flexcon.com
Graphic Advertising for Floors Application Instructions FLEXcon's System for Graphic Advertising for Floors is designed to be applied to smooth surfaces including: waxed and non-waxed commercial PVC tile, certain ceramic tile, and sealed concrete. FLOOR CONDITION: Floor surface must be clean prior to application of graphics. Traditional floor cleaning methods can be used to prepare the surface. Insure that the floor surface is adequately dry before application of graphics. [CAUTION: FLEXcon s System for Graphic Advertising for Floors can be applied at a temperature as low as 50 F (10 C).] APPLICATION METHOD: 1. Peel the backing paper (release liner) 1" down from the top. Fold, and crease the backing paper. 2. Align and apply the graphic starting at the top using firm strokes with a plastic squeegee, stiff cardboard, or a soft cloth. Continue removing the backing paper and smooth out the squeegee. Re-squeegee the edges of the graphic using firm strokes to insure edge adhesion. ROUTINE MAINTENANCE: 1. Do not clean or wax graphics for at least 24 hours after application. 2. When selecting a floor wax, insure it meets or exceeds ASTM D 2047 standards for appropriate static coefficient of friction (.5 min) 3. Avoid damaging graphics by heavy equipment traffic (fork trucks, pallets, or other heavy equipment). CAUTION: To avoid risk of injury, immediately remove graphics if any edge of the graphic lifts, and replace with a new graphic. REMOVAL INSTRUCTIONS: 1. Lift one edge of the graphic and pull, using short quick strokes. Pull at an angle less than 45 degrees for best results. 1 FLEXcon Industrial Park, Spencer, MA 01562-2642 USA Tel +1 (508) 885-8200 www.flexcon.com
Graphic Advertising for Indoor Carpets Application Instructions FLEXcon's System for Graphic Advertising for Indoor Carpets is designed to be applied to lowpile commercial-grade, stain-resistant or non-stain resistant carpets only. CARPET CONDITION: Carpet surface must be free of lint and debris prior to application of graphics. A thorough vacuuming is recommended. If recently shampooed or steam cleaned, make sure that the carpet surface is completely dry before application of graphics. [CAUTION: FLEXcon s System for Graphic Advertising for Indoor Carpets can be applied at a temperature as low as 50 F (10 C).] APPLICATION METHOD: 1. Peel the backing paper (release liner) 1" down from the top. Fold, and crease the backing paper. 2. Align and apply the graphic starting at the top using firm strokes with a plastic squeegee, stiff cardboard, or a soft cloth. Continue removing the backing paper and smooth out the squeegee. Re-squeegee the edges of the graphic using firm strokes to insure edge adhesion. ROUTINE MAINTENANCE: 1. Do not clean or vacuum over graphics for at least 24 hours after application. 2. Warm water/mild soap (dish detergent) and sponge can be used to periodically clean top surface of graphic. CAUTION: To avoid risk of injury, immediately remove graphics if any edge of the graphic lifts, and replace with a new graphic. REMOVAL INSTRUCTIONS: 1. Lift one edge of the graphic and pull, using short quick strokes. Pull at an angle less than 45 degrees for best results. CAUTION: Not all low-pile carpets are manufactured identically. Graphics may not have the same adherence properties on some low-pile plush carpets as on other commercial grade low-pile carpets. Please test all carpet surfaces prior to final application of graphic to be sure adhesive removes cleanly. 01202011 1 FLEXcon Industrial Park, Spencer, MA 01562-2642 USA Tel +1 (508) 885-8200 www.flexcon.com