SECTION 05721 - ORNAMENTAL RAILINGS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Glass supported railings. B. See Division 5 Section "Metal Stairs" for steel tube railings associated with metal stairs. C. See Division 5 Section "Pipe and Tube Railings" for railings fabricated from pipe and tube components. 1.2 PERFORMANCE REQUIREMENTS A. Structural Performance: Provide railings capable of withstanding the effects of gravity loads and the following loads and stresses within limits and under conditions indicated: 1. Handrails: a. Uniform load of 50 lbf/ ft. (0.73 kn/m) applied in any direction. b. Concentrated load of 200 lbf (0.89 kn) applied in any direction. c. Uniform and concentrated loads need not be assumed to act concurrently. 2. Top Rails of Guards: a. Uniform load of 50 lbf/ ft. (0.73 kn/m) applied in any direction. b. Concentrated load of 200 lbf (0.89 kn) applied in any direction. c. Uniform and concentrated loads need not be assumed to act concurrently. 3. Infill of Guards: a. Concentrated load of 50 lbf (0.22 kn) applied horizontally on an area of 1 sq. ft. (0.093 sq. m). b. Uniform load of 25 lbf/sq. ft. (1.2 kn/sq. m) applied horizontally. c. Infill load and other loads need not be assumed to act concurrently. 4. Glass-Supported Railings: Support each section of top rail by a minimum of three glass panels or by other means so top rail will remain in place if any one panel fails. B. Control of Corrosion: Prevent galvanic action and other forms of corrosion by insulating metals and other materials from direct contact with incompatible materials. ORNAMENTAL RAILINGS 05721-1
1.3 SUBMITTALS A. Product Data: For railings assembled from standard components, grout, anchoring cement, and paint products. B. Shop Drawings: Include plans, elevations, sections, details, and attachments to other Work. 1. For installed products indicated to comply with design loads, include structural analysis data signed and sealed by the qualified professional engineer responsible for their preparation. C. Samples: For each exposed finish required. D. Product Test Reports: Based on evaluation of comprehensive tests performed by a qualified testing agency, according to ASTM E 894 and ASTM E 935. 1.4 QUALITY ASSURANCE A. Product Options: Information on Drawings and in Specifications establishes requirements for system's aesthetic effects and performance characteristics. Do not modify intended aesthetic effects, as judged solely by Architect, except with Architect's approval. B. Preconstruction Testing Service: Owner will engage testing agency to test railings according ASTM E 894 and ASTM E 935. Payment will be made by owner 1. Provide test specimens and assemblies representative of proposed materials and construction. C. Mockups: Build mockups to verify selections made under sample submittals and to demonstrate aesthetic effects and set quality standards for fabrication and installation. 1. Build mockups for each form and finish of railing consisting of two posts, top rail, infill area, and anchorage system components. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following: B. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. Glass Supported Railings: a. Foreman Fabricators. 4605 McRee Ave., St. Louis, MO 63110 (314) 770-1717 ORNAMENTAL RAILINGS 05721-2
2.2 METALS A. Brackets, Flanges, and Anchors: Same metal and finish as supported rails, unless otherwise indicated. B. Aluminum: Provide alloy and temper recommended by aluminum producer and finisher for type of use and finish indicated, and with strength and durability properties for each aluminum form required not less than that of alloy and temper designated below. 1. Extruded Bars and Shapes, ASTM B 221 (ASTM B 221M), Alloy 6063-T5/T52. 2. Extruded Structural: ASTM B 429, Alloy 6063-T6. 3. Drawn Seamless Tubing: ASTM B 210, Alloy 6063-T832 4. Plate and Sheet: ASTM B 209, Alloy 5052-T3 5. Die and Hand Forgings: ASTM B 247, Alloy 6061-T6 6. Castings: ASTM B 26/B, Alloy A356.0-T6. 2.3 GLASS AND GLAZING MATERIALS A. Laminated Glass: ASTM C 1172, Condition A (uncoated), Type I (transparent flat glass), Quality-Q3 with clear, polyvinyl butyral interlayer not less than.060 inch thick 1. Kind: LT (laminated tempered) 2. Clear Glass: Class 1 (clear) 3. Lites for Structural Glass Balusters: Two, each of thickness required by structural loads, but not less than 6.0 mm thick. 4. Lites for Glass Infill Panels: Two, each of thickness required by structural loads, but not less than 5.0 mm B. Glazing Clips and Accessories: Provide glazing clips, setting blocks, shims, and related accessories as recommended or supplied by railing manufacturer. 2.4 MISCELLANEOUS MATERIALS A. Fasteners: Provide concealed fasteners, unless otherwise indicated 1. Aluminum Components: Type 304 or 316 stainless-steel fasteners. 2. Copper-Alloy Components: Silicon bronze (Alloy 651 or 655) fasteners. 3. Stainless-Steel Components: Type 316 or 18-8 stainless-steel fasteners. 4. Dissimilar Metals: Type 316 or 18-8 stainless-steel fasteners. B. Anchors: Provide chemical or torque-controlled expansion anchors, fabricated from corrosionresistant materials with capability to sustain, without failure, a load equal to six times the load imposed when installed in unit masonry and equal to four times the load imposed when installed in concrete, as determined by testing per ASTM E 488. C. Glass clamps: Use panel grip dry mount clamps in conjunction with appropriate base extrusion to mount glass. ORNAMENTAL RAILINGS 05721-3
2.5 FABRICATION A. General: Fabricate railings to comply with design, dimensions, and details indicated B. Welded Connections: Cope components at connections to provide close fit, or use fittings designed for this purpose. Weld all around at connections, including at fittings. C. Mechanical Connections: Connect members with concealed mechanical fasteners and fittings. D. Form changes in direction by mitering, welding and polishing corners. E. Form curves by bending in jigs to produce uniform curvature; maintain cross section of member throughout bend without cracking or otherwise deforming exposed surfaces. F. Close exposed ends of hollow railing members with prefabricated end fittings. G. Provide wall returns at ends of wall-mounted handrails, unless otherwise indicated. H. Brackets, Flanges, Fittings, and Anchors: Provide wall brackets, flanges, miscellaneous fittings, and anchors to interconnect railing members to other work, unless otherwise indicated. 2.6 FINISHES A. Aluminum: Class I, Clear Anodic Finish: AA-M12C22A41 complying with AAMA 611 PART 3 - EXECUTION 3.1 INSTALLATION A. General: Perform cutting, drilling, and fitting required for installing railings. Set railings accurately in location, alignment, and elevation. B. Coat concealed surfaces of aluminum that will be in contact with grout, concrete, masonry, wood, or dissimilar metals, with a heavy coat of bituminous paint. C. Anchor railing ends to concrete and masonry with flanges connected to railing ends and anchored to wall construction with anchors and bolts. D. Attach handrails to wall with wall brackets. 1. For wood stud partitions, use hanger or lag bolts set into wood backing between studs. 2. For steel-framed partitions, use hanger or lag bolts set into wood backing between studs. 3. For steel-framed partitions, fasten brackets to steel framing or concealed steel reinforcements using self-tapping screws of size and type required to support structural loads. 4. For steel-framed partitions, fasten brackets with toggle bolts installed through flanges of steel framing or through concealed steel reinforcements. ORNAMENTAL RAILINGS 05721-4
E. Installing Glass-Supported Railings: Attach base channel to building structure be sure base channel is level and plumb. Then insert dry mount glass clips into base channel. Set glass panels inside glass clips and tighten fastener so that glass is plumb. Use rubber gasket to seal off gap between glass and shoe. Apply cladding to shoe to match top cap. END OF SECTION 05721 ORNAMENTAL RAILINGS 05721-5