MSE 310 on-roof/flat-roof mounting system

Solar products MSE 310 on-roof/flat-roof mounting system For the CTE 319 CH collector of the Compact line ENGLISH

Installation and operating instructions Version 02 - Stand 07/2010 Art.-Nr.: 271 727 Auf-/Flachdach Montagesystem MSE 310 für Schüco Flachkollektoren CTE 319 CH, number of article 271 618 and CTE 319 CH AR, number of article 271 618 Printed in Germany, Copyright by Schüco International KG

Foreword List of contents Vorwort Dear Customer, Thank you for choosing Schüco Solar products and placing your trust in our company. Prior to first installation, we recommend you attend a training course at our training centre or, if this is not possible, that you arrange for on-site training from one of our service engineers. Training and qualification of the fabricators/installers Schüco requires that installation only be carried out by technically qualified and authorised personnel with a recognised qualification (verified by a state or national body) or the appropriate expertise in the relevant technical field. Please call our technical support if you have any questions or suggestions +44 19 08 28 91 88 Please note the following information regarding the relevant laws, legislation and technical regulations When setting up solar energy systems, the laws and regulations at local, state, European and international level that apply to the country in question must be observed. Accepted practice as usually codified in standards, guidelines, specifications, general and technical regulations laid down by local and national bodies, power supply companies, trade organisations and technical committees in the relevant sector must be followed. The installation of solar units may put additional strain on the existing substructure and make increased demands in terms of watertightness with regard to roof, wall and sealing and this must be taken into account accordingly. To meet regulations aimed at preventing accidents, it may be necessary to use safety equipment (straps, scaffolding, harnesses, etc). Such safety equipment is not supplied and must be ordered separately. Foreword 3 Training and qualification of the fabricators/installers 3 Please note the following information relating to the relevant laws, legislation and technical regulations 3 List of contents 3 Explanation of pictograms used 4 Tools required 4 Required installation aids 5 Removal and disposal of the packaging 5 General information, hazard warnings and safety instructions 5 Product description: MSE 310 on-roof mounting system 6 Snow/wind load 6 One Turn, One Turn 18/22 and hammer-head bolt 6 Materials to be provided by others 6 Contents of the MSE 310 mounting kit, landscape collector installation, one above the other 7 Also required 7 Overview: on-roof mounting system, landscape collector installation, vertical mounting rails 8 On-roof installation, vertical mounting rails: dimensions/fixing distances 8 On-roof installation, vertical mounting rails: batten-mounted fixing points 10 On-roof installation, vertical mounting rails: rafter-mounted fixing points 12 Installation of vertical mounting rails 14 Landscape collector installation on vertical mounting rails 16 Contents of the MSE 310 mounting kit, portrait collector installation, one above the other 17 Also required 17 Materials to be provided by others 17 Overview: on-roof mounting system, portrait collector installation, horizontal mounting rails 18 On-roof installation, horizontal mounting rails: dimensions/fixing distances 19 On-roof installation, horizontal mounting rails: batten-mounted fixing points 20 On-roof installation, horizontal mounting rails: rafter-mounted fixing points 22 Installation of horizontal mounting rails 24 Portrait collector installation on horizontal mounting rails 25 Installation of additional collectors 26 Flat-roof installation: general information, hazard warnings and safety instructions 28 Product description: MSE 310 flat-roof mounting system 28 Contents of the MSE 310 flat-roof mounting kit 28 Also required 29 Materials to be provided by others 29 Overview: flat-roof mounting system, portrait collector installation, horizontal mounting rails 29 Flat-roof installation, horizontal mounting rails: dimensions/fixing distances 30 Flat-roof bracket installation 31 Support cruciform installation 32 Flat roof installation: wind load/ballasting 33 Wind load (q) in [kn/m²] 33 Required ballasting 33 [kg per m² collector surface [kg/m²] 33 No. of edging stones 33 [Quantity per m² collector surface [kg/m²] 33 Hydraulic connection of Schüco CTE 319 CH and CTE 319 CH AR collectors 34 Hydraulic connection of the collectors 36 Vent tile for hydraulic pipes 36 Commissioning 37 Instructing the system operator/maintenance of the system/device 37 Maintenance 37 Draining/decommissioning 37 Environmental requirements 37 List of materials 37 Technical data for Schüco CTE 319 CH and CTE 319 CH AR 38 Pressure drop characteristic curve for Schüco CTE 319 CH and CTE 319 CH AR collectors 38 V02 07.2010 271 727 r1 3

Explanation of pictograms used Symbols used/tools requiredl The following hazard symbols are used: Important Risk of death or injury, could endanger the environment and the product Important Risk of scalding Important Important Risk of electric shock Risk of frost The following symbols are used: Important information Tighten in accordance with the material involved Weight/total weight (kg) See page Tighten firmly Content/volume (litres) Materials to be provided by others Pressure (bar) Drill/pre-drill Temperature Optional system Flush mm Connection Ø 6-figure numbers are always Schüco article numbers Parallel Follow the installation sequence Centre Position of the installation step in the large overview drawings Maintain an angle of 90 exactly Tools required Pencil/chalk Allen key 6 mm 221 089 Cordless screwdriver/drill Folding rule/tape measure General installation tool for heating/water/sanitation Flat blade/cross-recess screwdriver Open-ended spanner 13/14, 2 x 17/19 mm 2 x 22/27 mm, 2 x 32/34 mm 4 271 727 r1 V02 07.2010

Required installation aids Collector carrying handles 221 088 Safety harness 221 522 Installation aids/packaging/safety Product description/snow and Removal and disposal of the packaging Do not use sharp instruments to open the packaging. The packaging consists of cardboard, wood and labelled plastic. Dispose of the packaging in accordance with the relevant laws and with technical regulations. Adhere to the environmental regulations with regard to recycling, re-use and disposal of consumables and components in accordance with the national and local regulations. General information, hazard warnings and safety instructions Important Important Risk of death or injury from falling. Wear a safety harness. However, do not attach the safety harness to the mounting systems or to chimneys Danger to people and the environment from falling objects. Secure the site against falling objects. Section off the site if necessary. Important Important Risk of damage to the product. The hydraulic connections are not suitable for carrying the collectors they may break off. Use carrying handles (221 088) or appropriate cables to transport the collectors. Risk of death or injury, could endanger the environment and the product. Do not step on mounting rails once installed. Do not use them as ladders or fixing points for the safety harness. The mounting rails, roof anchors and roof construction will be damaged and lose their structural loadbearing capacity. Use the normal roof construction (rafters) for the points mentioned. Important Risk of damage to the hydraulic pipes from freezing liquids. Never fill the solar circuit with water. Use Schüco solar fluid only. The Schüco solar fluid is intended for a temperature range from -24 C to +200 C and guarantees sufficient corrosion protection. Important Risk of scalding from hot water or pipework. The temperature of the collectors and pipework during maintenance or servicing may be a maximum of 70 C. If necessary, leave the installation for some time before proceeding. Shade the collectors if necessary.. Important Risk of death or injury from electric shock. For buildings which require lightning protection, the collector array must be integrated into this. V02 07.2010 271 727 r1 5

Product description: MSE 310 on-roof mounting system The Schüco MSE 310 on-roof mounting system is used to install between one and five (depending on the kit) Schüco CTE 319 CH collectors. It must be used in accordance with the proof of structural integrity (to see the proof of structural integrity, visit www.schueco.com). The MSE 310 on-roof mounting system can be used on roof pitches between a minimum of 22 and maximum of 65. The system statics permit a maximum installation height from 0 to 20 m. The total weight (system, filling etc.) is approx. 46 kg per collector. The specific weight per m2 collector surface is approx. 20 kg. Do not exceed the roof load-bearing capacity during installation. An alternative use or a use beyond this remit is not in accordance with its purpose. Incorrect use can result in the death or serious injury of the user or a third party, and may damage the appliance, the installation or other material assets. The manufacturer/supplier shall not be liable for any resulting damage. The user alone will bear the risk. Due to the use of pure materials in the construction, the individual components of Schüco solar products can be recycled or re-used (see List of materials section).. Product description/snow and wind load/one Turn The maximum permissible pressure loading from snow and wind load is 1.1 kn/m². The maximum permissible loading from negative wind load is 1.0 kn/m². Snow/wind load As a system manufacturer, Schüco recommends conforming to DIN 1055 for structural calculations. The pressure coefficients (wind) and shape values (snow) are calculated in accordance with DIN 1055-100, DIN 1055-4 and DIN 1055-5. Calculate the values of local snow loads in accordance with countryspecific data. Calculate the values of local snow loads in accordance with countryspecific data. The loads present on site (in kn/m²) must be calculated in accordance with the applicable national standards. Do not interpolate intermediate values. Instead, select the next highest value. Refer to the Schüco MSE design aids for the description of definitions and the procedure for calculating loads and dimensions, as well as the calculation of span widths for the different snow and wind loads. The ballasting values for flat-roof mounting systems to overcome the wind load can be found on page 33. One Turn, One Turn 18/22 and hammer-head bolt Lock the OneTurn/hammer-head bolt in place by turning it 90 clockwise. The screw head of the OneTurn/hammer-head bolt must be anchored diagonally in the mounting rail groove. After aligning the mounting rails or flat-roof brackets, tighten the threaded sleeves or nuts. 90 90 Materials to be provided by others Screws for mounting battens and fixing points. Lining material for roof rafters Ventilation tile, general installation/assembly material for heating/water/sanitation. 6 271 727 r1 V02 07.2010

Contents of the MSE 310 mounting kit, landscape collector installation, one above the other Contents of delivery/required accessories * 271 711* 271 712 271 713 271 714 271 715 2 8 12 16 20 2 M8 14 4 4 4 4 4 4 4 4 2 2504 mm 2 3756 mm 2 5008 mm 2 6260 mm 2152 mm 2074 mm 2 30 90 2000 3 30 90 2000 3 30 90 2000 4 30 90 2000 5 30 90 2000 17 The MSE 310 single kit with landscape collector is installed with horizontal mounting rails. Install as described from page 17 onwards. Also required 271 711 271 712 271 713 271 714 271 715 271 742 4 6 6 8 10 271 839 4 6 6 8 10 271 839 ¹) 271 840 ²) 2 2 2 3 271 618 2 3 4 5 231 039 231 040 2 3 4 ¹) PU = 4, only for aluminium fixing points ²) PU = 4, only for steel fixing points V02 07.2010 271 727 r1 7

Overview: on-roof mounting system, landscape collector installation, vertical mounting rails Overview drawing/dimensions 7.1 6.0 6.0 1.0 2.0 6.0 6.0 7.1 7.0 7.8 2.0 8.1 8.8 8.0 3.9 4.0 3.0 8.1 8.5 9.0 1.0 3.9 5.0 6.0 5.0 6.0 3.9 4.0 3.0 2.01 4.0 2.01 3.0 Key 1.0 Flat-plate collector 2.0 Mounting rail without end stop 2.01 Grooved pin (pre-assembled) 3.0 Fixing points 3.9 Mounting battens 4.0 One Turn 18 for steel fixing pointsone Turn 22 for aluminium fixing points 5.0 Anti-slip device 6.0 Anti-slip device 7.0 Collector connector 7.1 90 clamping ring fitting 7.8 Thermal insulation 8.0 Collector array connection kit, 15 mm 8.1 Clamping ring fitting 8.5 Temperature sensor 8.8 Thermal insulation 9.0 Sensor plug On-roof installation, vertical mounting rails: dimensions/fixing distances 200 y = ~1000 2102 * x = ~1600 1202 4 The number of roof anchors required will depend on prevailing structural parameters. The number of roof anchors specified here are minimum requirements. * The MSE 310 single kit with landscape collector is installed with horizontal mounting rails. Install as described from page 17 onwards. 2102 6 250 2504 y = ~1000 ~1000 250 x = ~1600 8 271 727 r1 V02 07.2010

Dimensions 2102 6 2102 8 500 500 y = ~1400 3756 y = ~1400 5008 ~1400 ~1400 500 x = ~1600 ~1400 500 x = ~1600 2102 10 500 y = ~1400 6260 ~1400 ~1400 ~1400 500 x = ~1600 V02 07.2010 271 727 r1 9

On-roof installation, vertical mounting rails: batten-mounted fixing points Installation x, y = 8 9 x y A B A B A C Precisely align the vertical leg of the fixing point at a right angle to the roof pitch. C D C D 10 271 727 r1 V02 07.2010

Installation x x, y = 8 9 y Mounting rail installation: 14 V02 07.2010 271 727 r1 11

On-roof installation, vertical mounting rails: rafter-mounted fixing points Installation x, y = 8 9 x y A B A B Precisely align the vertical leg of the fixing point at a right angle to the roof pitch. 12 271 727 r1 V02 07.2010

Installation x x, y = 8 9 y OK A B A B V02 07.2010 271 727 r1 13

Installation of vertical mounting rails Installation Important Risk of death or injury, could endanger the environment and the product. Do not step on installed mounting rails. Do not use them as ladders or fixing points for the safety harness. The mounting rails, roof anchors and roof construction will be damaged and lose their structural load-bearing capacity. Use the normal roof construction (rafters) for the points mentioned. Important Risk of damage to the collector frame. The fixing points must not project beyond the top edge of the mounting rails. d1 d2 14 271 727 r1 V02 07.2010

Installation d1 d2 d1 = d2 Important Risk of death or injury, could endanger the environment and the product. Secure the mounting rails using an anti-slip device to prevent them from slipping. For each mounting rail, a mounting rail antislip device must be installed after every fourth vertical fixing point. Install these just above the fixing points as per the drawing below. 256 022 Anti-slip device for mounting rail. V02 07.2010 271 727 r1 15

Landscape collector installation on vertical mounting rails Installation u1 = u2 u1 u2 16 271 727 r1 V02 07.2010

Contents of the MSE 310 mounting kit, portrait collector installation, one above the other Contents of delivery/required accessories 271 705 271 706 271 707 271 708 271 710 2 4 6 8 10 2 M8 14 4 M8 14 6 M8 14 8 M8 14 10 M8 14 1252 mm 2504 mm 3756 mm 5008 mm 6260 mm 1174 mm 2426 mm 3678 mm 14930 mm 6182 mm 2 30 90 2000 3 30 90 2000 2 30 90 3000 4 30 90 2500 4 30 90 3000 Also required 271 711 271 712 271 713 271 714 271 715 257 119 4 6 6 8 10 257 121 4 6 6 8 10 271 839 ¹) 271 840 ²) 2 2 2 2 271 618 2 3 4 5 231 039 231 040 2 3 4 ¹) PU = 4, only for aluminium fixing points ²) PU = 4, only for steel fixing points Materials to be provided by others Screws for mounting battens and fixing points. Lining material for roof rafters. Ventilation tile, general installation/assembly material for heating/water/sanitation. V02 07.2010 271 727 r1 17

Overview: on-roof mounting system, portrait collector installation, horizontal mounting rails Overview drawing Key 1.0 Flat-plate collector 2.0 Mounting rail without end stop 2.1 Mounting rail with end stop 2.11 Socket head bolt (hexagon socket head) 3.0 Fixing points 3.9 Mounting battens 4.0 One Turn 18 for steel fixing points One Turn 22 for aluminium fixing points 6.0 Retaining clamp with One-Turn 7.0 Collector connector 7.1 90 clamping ring fitting 7.8 Thermal insulation 8.0 Collector array connection kit, 15 mm 8.1 Clamping ring fitting 8.5 Temperature sensor 8.8 Thermal insulation 9.0 Sensor plug 4.0 3.9 3.0 6.0 2.0 8.0 8.8 8.1 1.0 7.0 7.8 8.1 7.1 7.1 8.5 9.0 6.0 6.0 1.0 3.9 4.0 2.11 3.0 2.01 18 271 727 r1 V02 07.2010

On-roof installation, horizontal mounting rails: dimensions/fixing distances Dimensions 1252 2102 2504 4 6 2102 y = ~1900 6 175 x = ~850 3756 175 y = ~1900 250 x = ~1000 x = ~1000 250 The number of roof anchors required will depend on prevailing structural parameters. 3756 2102 The number of roof anchors specified here are minimum requirements. 500 y = ~1900 x = ~1400 500 x = ~1400 500 8 5008 2102 500 y = ~1900 500 x = ~1400 x = ~1400 x = ~1400 500 10 6260 2102 500 x = ~1400 y = ~1900 x = ~1400 500 x = ~1400 V02 07.2010 271 727 r1 19

On-roof installation, horizontal mounting rails: batten-mounted fixing points Installation x, y = 19 x y A B A B A Precisely align the vertical leg of the fixing point at a right angle to the roof pitch. B 20 271 727 r1 V02 07.2010

Installation D C D C x, y = 19 x y Mounting rail installation:: 24 V02 07.2010 271 727 r1 21

On-roof installation, horizontal mounting rails: rafter-mounted fixing points Installation x, y = 19 x y A B A B Precisely align the vertical leg of the fixing point at a right angle to the roof pitch. 22 271 727 r1 V02 07.2010

Installation x OK y x, y = 19 A B A B V02 07.2010 271 727 r1 23

Installation of horizontal mounting rails Installation Important Important Risk of death or injury, could endanger the environment and the product. Do not step on installed mounting rails. Do not use them as ladders or fixing points for the safety harness. The mounting rails, roof anchors and roof construction will be damaged and lose their structural load-bearing capacity. Use the normal roof construction (rafters) for the points mentioned. Risk of damage to the collector frame. The fixing points must not project beyond the top edge of the mounting rails. a a = 40 mm b1 = b2 b1 b2 a a 24 271 727 r1 V02 07.2010

Portrait collector installation on horizontal mounting rails Installation V02 07.2010 271 727 r1 25

Installation Installation of additional collectors 26 271 727 r1 V02 07.2010

Installation V02 07.2010 271 727 r1 27

Flat-roof installation: general information, hazard warnings and safety instructions Flat-roof installation/general information/safety instructions/ product description/contents of delivery Avoid accumulation of loose material. Fit protective matting under the flat-roof mounting system, if required. The supporting surface must be flat and load-bearing.. 1 m Maximum installation area and height. 2 m 8 m 8-20 m Product description: MSE 310 flat-roof mounting system The Schüco MSE 310 flat-roof mounting system is used to install between one and five (depending on the kit) Schüco CTE 319 CH collectors on a flat roof. It must be used in accordance with the proof of structural integrity (to see the proof of structural integrity, visit www.schueco.com). The system statics permit a maximum installation height from 0 to 20 m. The total weight (system, filling etc.) is approx. 46 kg per collector without ballasting for the flat-roof bracket. The specific weight per m 2 collector surface is approx. 20 kg. An alternative use or a use beyond this remit is not in accordance with its purpose. Incorrect use can result in the death or serious injury of the user or a third party, and may damage the appliance, the installation or other material assets. The manufacturer/supplier shall not be liable for any resulting damage. The user alone will bear the risk. Due to the use of pure materials in the construction, the individual components of Schüco solar products can be recycled or re-used (see List of materials section). The maximum permissible pressure loading from snow and wind load is 1.1 kn/m². The maximum permissible loading from negative wind load is 1.0 kn/m². Contents of the MSE 310 flat-roof mounting kit 271 705 271 706 271 707 271 708 271 710 2 4 6 8 10 2 M8 14 4 M8 14 6 M8 14 8 M8 14 10 M8 14 1252 mm 2504 mm 3756 mm 5008 mm 6260 mm 1174 mm 2426 mm 3678 mm 14930 mm 6182 mm 28 271 727 r1 V02 07.2010

Also required Required accessories/overview drawing 271 711 271 712 271 713 271 714 271 715 271 858 2 3 4 5 6 272 091 271 618 2 3 4 5 231 039 231 040 2 3 4 Materials to be provided by others Screws for mounting battens and fixing points. Lining material for roof rafters. Ventilation tile, general installation/assembly material for heating/water/ sanitation. Edging stones for ballasting to overcome the wind load. Overview: flat-roof mounting system, portrait collector installation, horizontal mounting rails Key 1.0 Flat-plate collector 2.0 Mounting rail without end stop 2.1 Mounting rail with end stop 2.11 Socket head bolt (hexagon socket head) 3.0 Flat-roof bracket 3.1 Support cruciform 4.0 Hammer-head bolt 6.0 Retaining clamp with One-Turn 7.0 Collector connector 7.1 90 clamping ring fitting 7.8 Thermal insulation 8.0 Collector array connection kit, 15 mm 8.1 Clamping ring fitting 8.5 Temperature sensor 8.8 Thermal insulation 9.0 Sensor plug 2.0 3.0 8.0 7.1 8.8 8.1 9.0 8.1 8.5 6.0 4.0 3.1 7.0 7.8 7.1 6.0 6.0 1.0 1.0 2.11 2.1 4.0 V02 07.2010 271 727 r1 29

Flat-roof installation, horizontal mounting rails: dimensions/fixing distances Dimensions 1252 2 2504 3 2102 2102 1720 1720 f 1020 g=70 g=70 f 1020 g=230 f 1020 g=230 3756 4 2102 500 2102 1720 g=230 f 1020 f 1220 f 1020 g=230 ~210 1320 100 5008 5 2102 1720 g=230 f 1020 f 1220 f 1220 6260 f 1020 g=230 2102 6 1720 g=230 f 1020 f 1220 f 1220 f 1220 f 1020 g=230 30 271 727 r1 V02 07.2010

Flat-roof bracket installation e1 = e2 e1 e2 Flat-roof installation 40 mm 40 mm 90 f g f, g = 30 V02 07.2010 271 727 r1 31

Support cruciform installation Flat-roof installation 2 Affix additional flat-roof brackets for additional collectors. 32 271 727 r1 V02 07.2010

Flat roof installation: wind load/ballasting Flat roof installation/wind load/ballasting Important Important Risk of death or injury, could endanger the environment and the product. The roof/building may collapse. The maximum roof load-bearing capacity must not be exceeded. Risk of death or injury, could endanger the environment and the product. Do not step on installed mounting rails. Do not use them as ladders or fixing points for the safety harness. The mounting rails, flatroof brackets and roof construction will be damaged and lose their structural load-bearing capacity. 1000 250 80 ~48 kg Calculate the values of local snow loads in accordance with countryspecific data. Ballasting for the flat-roof mounting system is applied in accordance with the table below: Wind load (q) in [kn/m²] Required ballasting [kg per m² collector surface [kg/m²] No. of edging stones [Quantity per m² collector surface[kg/m²] 0,50 148 4 0,65 186 4 0,75 228 5 0,80 243 5 0,85 259 6 0,90 275 6 0,95 291 6 Flat-roof mounting system: collector installation 18 The collectors are installed in the same way as for on-roof installation with horizontal mounting rails. See page 18 onwards. V02 07.2010 271 727 r1 33

Hydraulic connection of the Schüco CTE 319 CH / CTE 319 CH AR collector Hydraulic connection mm = 12 CTE 319 CH/ CTE 319 CH AR 5 (1 5) 6 (2 3) 8 (2 4) 9 (3 3) 10 (5 2) 12 (4 3) 15 (5 3) 20 (1 5) Cu Ø 15 1 Cu Ø 18 1 Cu Ø 18 1 Cu Ø 22 1 Cu Ø 22 1 Cu Ø 22 1 Cu Ø 28 1 Cu Ø 28 1 34 271 727 r1 V02 07.2010

Hydraulic connection Important Risk of damage to the product. Rotating the central unit (nut) of the clamping ring fitting will damage the collector pipework. The centre of the collector connector must not be rotated during installation. V02 07.2010 271 727 r1 35

Hydraulic connection/vent tile Hydraulic connection/vent tile Vent tile for hydraulic pipes 60 mm 60 mm A B Vent tiles must be bonded to the roofing membrane in accordance with the relevant system so as to be watertight. 36 271 727 r1 V02 07.2010

Commissioning Commissioning/instructing the operator/maintenance/ decommissioning/environmental requirements Commission the system in accordance with the installation/operating instructions for the Schüco solar station. Instructing the system operator/maintenance of the system/device Train the system operator in: The correct operation and the functions of the system/device The correct and most efficient temperature setting(s) The necessity for regular maintenance The maintenance instructions described To avoid damage to the surface of the storage cylinder, clean the external casing with a damp cloth only; never use cleaners containing sand or abrasive materials, or solvent cleaning agent or paint thinner (nitro etc.). The maintenance instructions described Maintenance Maintain the system in accordance with the installation/operating instructions for the Schüco solar station. Check the mounting system for loose screws and nuts in an annual visual inspection. Re-tighten the loose screws and nuts to suit the material. Draining/decommissioning Drain the system in accordance with the installation/operating instructions for the Schüco solar station. Decommission the system in accordance with the installation/operating instructions for the Schüco solar station. The Schüco CTE 319 CH and CTE 319 CH AR collectors are maintenance-free. Environmental requirements When servicing or decommissioning solar stations, observe the environmental requirements with regard to recycling, re-use and disposal of operating materials and components in accordance with the local, country-specific and international current technical regulations and official regulations. For the materials to be recycled/re-used correctly, use the list of materials for the individual system components in the next section. List of materials 1.00 Solar glass ESG 1.01 Gasket EPDM 1.02 Pipework Cu-DPH 1.03 Absorber plate SF-Cu 1.04 Insulation Mineral wool 1.05 Pipe bushing VMQ 50 1.06 Solar Panel EN AW 6060 1.07 Absorber bracket Edelstahl 1.4310 1.08 Backing plate EN AW 6060 1.09 Corner angle AlMg1 2.0 Mounting rail EN AW 6060 3.0 Flat-roof brackets EN AW 6060 3.1 Support cruciform EN AW 6060 3.9 Mounting battens Nadelholzklasse II 4.0 One Turn Edelstahl 1.4310 1.00 1.02 1.03 1.01 1.04 1.05 1.07 1.06 1.08 1.08 V02 07.2010 271 727 r1 37

Technical data for Schüco CTE 319 CH and CTE 319 CH AR collectors Technical data h l = 2102 mm CTE 319 CH CTE 319 CH AR b = 1202 mm l A h = 80 mm A = 2,53 m² bar max: test: 1,7 10 10 2,5 10 10 b 44 44 C mm 203 12 210 12 Pressure drop characteristic curve for Schüco CTE 319 CH and CTE 319 CH AR collectors 38 271 727 r1 V02 07.2010

Schüco International KG Whitehall Avenue Kingston, Milton Keynes MK10 0AL United Kingdom Phone +44 19 08 28 21 11 Fax +44 1908 28 21 24 www.schueco.co.uk Schüco International KG Karolinenstraße 1-15 33609 Bielefeld Deutschland Telefon +49 5 21-7 83-0 Telefax +49 5 21-7 83-4 51 www.schueco.com