4. GENERAL SECONDARIES & SERVICES 4.- INDIVIDUAL PHASE SECONDARY OVERHEAD LINE EXTENSIONS 4.- SECONDARY AND SERVICE CABLE SPLICES 4.- INSULATED SERVICE ENTRANCE COMPRESSION CONNECTORS 4.- 4. POLE ATTACHMENTS POLE ATTACHMENT DEVICES 4.- MULTIPLEX SERVICE ATTACHMENTS TO POLES 4.-6 4.4 SECONDARIES SECONDARY SPACER INSTALLATIONS OVERHEAD TRIPLEX SECONDARIES 4.4-6 4.4-8 4.5 SERVICES SERVICE ATTACHMENT METHODS O4.5- OVERHEAD SERVICE POLE 4.5-6 TEMPORARY SERVICE POLE 4.5-8 BILLBOARD SERVICE ENTRANCE REQUIREMENTS METHOD "A" 4.5- BILLBOARD SERVICE ENTRANCE REQUIREMENTS METHOD "B" 4.5-7/8/ CECCONI GUINN ELKINS SECTION 4 - SECONDARY CONSTRUCTION OVERHEAD TABLE OF CONTENTS 4.-A
GENERAL. THE NEUTRAL SHALL BE COMMON TO BOTH PRIMARY AND SECONDARY CIRCUITS ON WYE SYSTEMS. THE NEUTRAL SHALL BE MULTI-GROUNDED.. THE NEUTRAL CONDUCTOR SHALL ALWAYS BE IN THE TOP POSITION ON AN OPEN-WIRE SECONDARY CIRCUIT. SIZING OF SECONDARY CONDUCTORS WILL DEPEND ON THE AMOUNT OF LOAD, THE TYPE OF LOAD (SUCH AS MOTORS, ETC.), AND THE VOLTAGE DROP.. ALL SERVICE CONDUCTORS WILL BE OF COVERED ALUMINUM. THE REQUIRED SIZE, SHALL BE SPECIFIED BY THE ENGINEER. 4. THE SERVICE ENTRANCE LOCATION WILL BE DETERMINED BY THE COMPANY AND MUST BE AGREED TO BY THE CUSTOMER. CUSTOMER'S REQUESTS FOR NON-STANDARD LOCATIONS FREQUENTLY REQUIRE AN ADDITIONAL CHARGE. 5. FOR THREE PHASE FOUR WIRE DELTA SECONDARY CABLE AND SERVICES, THE PHASE CONDUCTOR WITH THE MOST NUMBER OF RAISED RIBS WILL BE THE HIGH (8 VOLT) PHASE. 6. USE INSULINKS OR INSTALL COVERS OVER SECONDARY CABLE OR SERVICE CABLE PHASE CONNECTORS. 7. STREETLIGHT CIRCUITS ARE TO BE CONSIDERED AS SECONDARY. 8. BEFORE CUTTING THE LACING WIRE ON AERIAL SECONDARY CABLE, BIND THE LACING WITH SEVERAL TURNS OF SCRAP LACING WIRE. 9. TO DEADEND THE PHASE CONDUCTORS OF AERIAL SECONDARY CABLE WHILE ALLOWING NEUTRAL TO CONTINUE ON, FIRST TAPE THE ENDS OF THE PHASE CONDUCTOR THEN BEND THEM BACK AND SECURE WITH SEVERAL WRAPS OF THE BINDING WIRE. COVER ENDS IF NOT IN USE. LIMIT FOR ALUMINUM CABLES NOT REQUIRING GUYING WIRE SIZE CODE NAME **SPAN LENGTH #4 DUPLEX SECONDARY #4 TRIPLEX SERVICE # TRIPLEX SERVICE #/ TRIPLEX SERVICE/SECONDARY #4/ TRIPLEX SERVICE 5/5 TRIPLEX SERVICE #/ QUADRUPLEX SECONDARY #4/ QUADRUPLEX SECONDARY 6.4/5 QUADRUPLEX SERVICE WHIPPET CRAB SOLASTER SANDCRAB LEPAS *NO CODE NAME VIATKA WALKING *NO CODE NAME 5' 5' 5' ' 5 QUADRUPLEX SERVICE *NO CODE NAME 4' * WIRE SIZE CUSTOM MADE IN FIELD ** BASED ON 5 LB. CUSTOMER MAST TENSION LIMIT AS INDICATED IN THE REQUIREMENTS FOR ELECTRIC SERVICE AND METER INSTALLATIONS MANUAL. 7' 5' 9' 6' 4' /8/ BURLISON ADCOCK SECONDARIES & SERVICES 4.- R
NORMAL POINT OF DELIVERY NORMAL POINT OF DELIVERY 5' 5' 5' NORMAL P.O.D. NO CHARGE NORMAL P.O.D. IS ON THE END OF THE BUILDING NEAREST THE OVERHEAD SOURCE. NO EXTRA POLE CHARGE TO NORMAL P.O.D. USING OH SECONDARY LIFT POLES WIRING BEYOND NORMAL POINT OF DELIVERY 4' NOTE: DIMENSIONS SHOWN ARE FOR ILLUSTRATIVE PURPOSES ONLY. 7' 6' POLE FEE AND PER FOOT CABLE CHARGES APPLY. CONTACT COMPANY REPRESENTATIVE FOR COSTS. 8/8/4 SIMPSON GUINN ADCOCK 5// SIMPSON SIMPSON ADCOCK 4// SIMPSON SIMPSON ELKINS 7/8/ BURLISON GUINN ELKINS INDIVIDUAL PHASE SECONDARY OVERHEAD LINE EXTENSIONS DEC DEM DEP DEF X 4.-
SEMI-TENSION SLEEVE INSULATED SERVICE ENTRANCE COMPRESSION CONNECTOR; SEE DWG 4.- FOR INSTALLATION INSTRUCTIONS AND CONNECTOR INFORMATION 6" 6" TRIPLEX CABLE SPLICE SEMI-TENSION SLEEVES FOR SERVICE NEUTRALS CATALOG NUMBER CONDUCTOR SIZE 56 #6 ACSR OR ALLOY 64 #4 ACSR OR ALLOY 64 # ACSR OR ALLOY 656 #4/ ACSR OR ALLOY INSULATED SERVICE ENTRANCE COMPRESSION CONNECTOR; SEE DWG 4.- FOR INSTALLATION INSTRUCTIONS AND CONNECTOR INFORMATION SEMI-TENSION SLEEVE 6" 6" 6" QUADRUPLEX CABLE SPLICE. WHEN SPLICING NEUTRAL, CUT OFF ENOUGH CONDUCTOR TO ASSURE A LOOSE WRAP OF PHASE CONDUCTORS AT SPLICE.. USE "BG" GROOVE OF BURNDY TOOL, OR EQUIVALENT TOOL WITH DIE FOR 5/8" SLEEVES. USE 84 DIE ON 4/ SLEEVE.. CLEAN CONDUCTORS BY WIRE BRUSHING. 4. FOR DETAILS OF INSULATED COMPRESSION CONNECTOR INSTALLATION SEE DWG 4.-. 5. "NEW" TRIPLEX OR QUADRUPLEX SECONDARIES AND SERVICES MAY CONTAIN A MAXIMUM OF ONE SPLICE PER SPAN. "REPAIR" TRIPLEX OR QUADRUPLEX SECONDARIES AND SERVICES MAY CONTAIN A MAXIMUM OF TWO SPLICES PER SPAN. 6. PHASE CONDUCTORS SHALL BE POSITIONED SUCH THAT CONTACT WITH THE NEUTRAL SLEEVE WILL NOT OCCUR. 7/8/ BURLISON GUINN ELKINS SECONDARY AND SERVICE CABLE SPLICES 4.-
NOTE STRIP LENGTH NOTE NOTE INSULATED COMPRESSION CONNECTOR SIZE TABLE PGN CN CONDUCTOR SIZE END MARKINGS END COLOR CONDUCTOR SIZE END COLOR 85 84 85 87 889 898 84 8 8 9498 956 956 95 6 4 4 / / / BLUE ORANGE ORANGE RED RED RED YELLOW YELLOW YELLOW 6 6 4 6 4 4 I/ BLUE BLUE ORANGE BLUE ORANGE RED ORANGE RED YELLOW / YELLOW / GRAY /O /O 4/O YELLOW YELLOW PINK / 4/ 4/O BLACK PINK PINK. STRIP INSULATION ON EACH CONDUCTOR FOR LENGTH SHOWN BY ARROWS ON SIDE OF CONNECTOR, CLEAN CONDUCTOR BY WIRE BRUSHING.. INSERT CONDUCTORS THROUGH CAPS ON EACH END UNTIL THEY HIT THE CENTER STOP.. MAKE THREE COMPRESSIONS ON EACH END. ROTATE TOOL SO THAT CRIMPS DO NOT LINE UP. USE "BG" GROOVE OF BURNDY TOOL, OR EQUIVALENT TOOL WITH DIE FOR 5/8" SLEEVES. REMOVE END CAPS WHEN INSTALLED ON BARE NEUTRAL. 4. INSULATED COMPRESSION CONNECTOR IS TO BE USED FOR NON-TENSION JOINTS ONLY. NO TAPING OR ADDITIONAL INHIBITOR IS REQUIRED. SEE 4.- FOR SERVICE DROP CABLE SPLICE. 9/4/ BURLISON ADCOCK INSULATED SERVICE ENTRANCE COMPRESSION CONNECTORS 4.- R
INSULATOR, SECONDARY SPOOL FOR TANGENT POLE NEUTRAL SUPPORT AND OPEN-WIRE SECONDARY SUPPORT (ANGLES TO 5 DEGREES) MACRO UNIT - CU ITEM NO. COMPATIBLE UNIT NSSBC QTY REQ'D NSSBC BILL OF MATERIALS QTY CATALOG PER NUMBER CU DESCRIPTION 8 BOLT, SPOOL, 5/8 X, GALV, DUI WASHERS 547 WASHER, SQ, -/4", /6, GALV. 5445 WASHER, LOCK, 5/8, COIL, DOUBLE, GALV. 8 BOLT, SPOOL, 5/8 X, GALV, DUI WASHERS 547 WASHER, SQ, -/4", /6, GALV. 5445 WASHER, LOCK, 5/8, COIL, DOUBLE, GALV. ISPLC 5 INSULATOR, SPOOL, INCH INSULATOR, SECONDARY RACK FOR ANGLE POLE NEUTRAL SUPPORT AND OPEN-WIRE SECONDARY DEAD ENDS MACRO UNIT - CU/CN ITEM NO. COMPATIBLE UNIT QTY REQ'D NSSCC BILL OF MATERIALS QTY CATALOG PER NUMBER CU DESCRIPTION 498 54 BOLT, MACH, SQ, 5/8- X, GALV CLEVIS, INSULATOR SPOOL, GALV, -/8" 547 WASHER, SQ, -/4", /6, GALV. ISPLC 5 INSULATOR, SPOOL, INCH. FOR FACTORY FORMED TIE INFORMATION, SEE.4-9. /8/ BURLISON ADCOCK 4// BURLISON BURLISON ELKINS 7/8/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. POLE ATTACHMENT DEVICES 4.- R
CU ISEYENUT58C CN 8 WEDGE GRIP 4" " " DETAIL SHOWN FOR / AND SMALLER TPX AND QPX (SEE NOTE ) ON OPPOSITE SIDE FROM EXISTING SECONDARY DEADEND ON SAME SIDE AS EXISTING SECONDARY CONNECTIONS TO OPEN WIRE SECONDARIES WEDGE GRIP CU SERCLMP4ALC CN 85 CU SERCLMPNALC CN 49 CU ISEYEBOLT58C CN 6 WEDGE GRIP EYENUT DEAD END CLAMP CN 4957 4" TO SERVICE TO SOURCE LIFT POLE GUYED LIFT POLE USE MINIMUM /4" GUYSTRAND AND 6" SCREW ANCHOR FOR ANGLE POLES AS NEEDED LIFT POLE ATTACHMENTS. FOR 4/ AND LARGER TPX & QPX, SUBSTITUTE STRAIGHT DEAD END CLAMP ( CN 4957) AND SALVAGED 4" STRAIN INSULATORS ( CN 98) FOR LOOP DEAD END CLAMP, AND EYEBOLT ( CN 6) FOR CLEVIS AND SPOOL.. APPLY INHIBITOR AND WIRE BRUSH ALL CONNECTIONS. USE ALUMINUM COMPRESSION CONNECTORS ON COPPER TO ALUMINUM CONNECTIONS. INSTALL CONNECTORS SO THAT ALUMINUM IS ABOVE COPPER.. POLES WITH ONLY SECONDARY CONDUCTORS WILL NOT BE EQUIPPED WITH A POLE GROUND. 4. POLES WITH METERING EQUIPMENT TO BE EQUIPPED WITH A POLE GROUND (EITHER WRAP BUTT OR TWO DRIVEN 5' GROUND RODS). 5 /8/ SIMMONS GUINN ADCOCK 4 /8/ BURLISON ADCOCK 4/7/ GUINN BURLISON ELKINS 7/8/ BURLISON GUINN ELKINS MULTIPLEX SERVICE ATTACHMENTS TO POLES 4.-6 R
SERVICE DROP LOCATED TO AVOID OBSTACLES OR TO CLEAR POLE FOR CLIMBING (TO BE USED ONLY WHERE SPECIFIED BY ENGINEER) SERVICE DROP FROM TRANSFORMER POLE (TO BE USED ONLY WHERE SPECIFIED BY ENGINEER) DOUBLE SERVICE DROP (TO BE USED ONLY WHERE SPECIFIED BY ENGINEER) SECONDARY SPACER 8" SPACING (CN ) " SPACING (CN 9) FOR 4/ ACSR MAXIMUM DOUBLE SERVICE BAIL CN 47. SERVICE DROP INSTALLATIONS SHALL BE APPLIED ONLY IN THOSE CASES WHERE THE ALTERNATIVE WOULD BE RELOCATING EXISTING POLES OR INSTALLING ADDITIONAL ONES TO SERVE CUSTOMERS.. SERVICE DROPS SHALL NOT BE SPECIFIED WHEN THE LOCATION IS INACCESSIBLE TO A LADDER.. INSTALLATIONS SHALL BE MADE SO THAT SAGS AND TENSIONS OF THE SECONDARY SERVICE CABLE ARE MAINTAINED FOR PROPER APPEARANCE. 4. MAXIMUM SIZE SERVICES PERMITTED FOR THIS INSTALLATION ARE 8' OF # TRIPLEX OR 6' OF #/ TRIPLEX. 5. MORE THAN ONE SERVICE PULL-OFF IN THE SAME SPAN IS NOT PERMITTED EXCEPT FOR BACK-TO-BACK SERVICES. DOUBLE TAP FOR SINGLE TAP USE SINGLE SERVICE BAIL ( CN 8) 6. SECONDARY SPACERS MAY BE INSTALLED AT APPROXIMATELY 5' INTERVALS TO PREVENT OUTAGES DUE TO SECONDARY CONDUCTORS COMING TOGETHER IN LONG SPANS. 6// BURLISON GUINN ELKINS SECONDARY SPACER INSTALLATIONS 4.4-6
PRIMARIES EXISTING PRI.-NEUT. SPACING PRIMARY NEUTRAL SEE DETAIL A 4" CLEAR. MIN. AT POLE TRIPLEX SECONDARY CLEARANCE " MIN. IN SPAN TELEPHONE/CATV MINIMUM CLEARANCE TO GROUND BELOW PER 9.- FINAL GRADE * GUY CLAMP PRIMARY NEUTRAL TPX BARE NEUT. TRIPLEX PHASE WIRES PRIMARY NEUT. SIZE GUY CLAMP CN 4/ AL 4574 #4 - #/ AL 59 DETAIL "A" (SEE CHART FOR SIZE & CN). THE PREFERRED METHOD IS TO INSTALL THE TRIPLEX BENEATH THE PRIMARY NEUTRAL, CLEAR-SPANNING FROM POLE TO POLE.. THE TRIPLEX AT ITS LOWEST POINT MUST BE AT LEAST " ABOVE THE TELEPHONE/CATV LINES BELOW. IF THERE ARE NO TELEPHONE/CATV LINES, THE TRIPLEX AT ITS LOWEST POINT MUST HAVE THE APPROPRIATE MINIMUM GROUND CLEARANCE GIVEN BY.-.. IF THE SAG OF THE TRIPLEX ENCROACHES THE MINIMUM CLEARANCE TO THE TELEPHONE/CATV LINES OR GROUND BELOW, THE TRIPLEX SHOULD BE ATTACHED TO THE PRIMARY NEUTRAL, AS SHOWN IN DETAIL A ABOVE, AS OFTEN AS NECESSARY TO ACHIEVE THE REQUIRED MINIMUM CLEARANCES. 4. ONLY # AND #4 TRIPLEX MAY BE ATTACHED TO THE PRIMARY NEUTRAL FOR ITS SUPPORT. THE LARGER SIZE TRIPLEXES MUST BE CLEAR-SPANNED BETWEEN POLES AND NOT SUPPORTED BY THE PRIMARY NEUTRAL. 8/6/4 EANES EANES ADCOCK 7/8/ BURLISON GUINN ELKINS OVERHEAD TRIPLEX SECONDARIES DEC DEM DEP DEF X 4.4-8
HOUSE BRACKETS FASCIA HOUSE BRACKET CN. HOUSE BRACKETS MUST BE INSTALLED IN STUDS (" X 4") OR EQUIVALENT SUPPORT. CUSTOMER'S GUY WIRE OR BRACE SERVICE MAST STEEL CONDUIT ONLY FASCIA MAST BRACKET /4" - /" CU SDEMASTCLMPSMC CN 67 " - 4" CU SDEMASTCLMPLGC CN 58. SERVICE MAST SHALL BE OF ADEQUATE STRENGTH OR BE SUPPORTED BY A GUY OR BRACE TO WITHSTAND A MAXMIUM TENSION FORCE OF 5 LBS. IMPOSED BY SERVICE DROP.. " RIGID STEEL CONDUIT IS REQUIRED FOR MASTS UP TO 4'. LONGER MAST HEIGHTS REQUIRE GUYING, BRACING, LARGER MAST SIZE OR SPECIAL SAG.. DRIP LOOPS SHALL BE FORMED ON SERVICE DROP SERVICE ENTRANCE CONDUCTORS.. THE CONNECTIONS OF THE SERVICE DROP CONDUCTORS TO THE SERVICE ENTRANCE CONDUCTORS SHALL BE MADE BELOW THE LEVEL OF THE SERVICE WEATHERHEAD.. SEE DWGS..- AND.- FOR SERVICE GROUND CLEARANCES AND DWGS..4-9A AND.4-9B FOR SERVICE CLEARANCES AT BUILDINGS. 4. SERVICE ENTRANCE CONNECTORS SHALL BE INSULATED PER NEC RULE -. 5. THE SERVICE POINT OF ATTACHMENT SHOULD BE LOCATED BELOW THE LEVEL OF THE WEATHERHEAD OR GOOSENECK. IF THIS IS IMPRACTICAL, THE POINT OF ATTACHMENT MUST BE LOCATED WITHIN 4" OF THE WEATHERHEAD OR GOOSENECK (REF. NEC -54C). 6. CUSTOMER IS RESPONSIBLE FOR PROVIDING AN ATTACHMENT POINT FOR MASONRY AND STEEL BUILDINGS. 7. SEE 4.-6 FOR SERVICE CLAMP COMPATIBLE UNITS. 8/6/4 EANES EANES ADCOCK /8/ BURLISON ADCOCK 7/8/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. SERVICE ATTACHMENT METHODS DEC DEM DEP DEF X 4.5-
4" MIN. SECURE TO POLE USING HOUSE BRACKET SCREW OR DRIVE HOOK SCREW MOUNTED IN THE SIDE OF POLE. DO NOT ATTACH TO TOP OF POLE. POLE OPTION A NOT TO SCALE BACKFILL WITH SOIL AND TAMP IN 6" LAYERS. HOLE DIAMETER SHALL BE JUST WIDE ENOUGH TO ALLOW TAMPING. 4'-7" POINT OF DELIVERY 5'-5" OPTION B NOT TO SCALE METER SOCKET (SEE NOTE ) POLE CONCRETE 6' BACKFILL WITH CONCRETE IN A 5" (MIN.) DIAMETER HOLE. '-" TO 5'-6" CUSTOMER'S EQUIPMENT (SEE NOTE B) CUSTOMER'S POLE (SEE NOTE A) '-6" MIN. ANYWHERE IN THE SPAN (8' MIN. IF OVER ROADS OR AREAS SUBJECT TO VEHICULAR TRAFFIC) POLE /4", 7-STRAND GUY (MIN.) 4' DEPTH 6' OPTION C NOT TO SCALE 4' DEPTH BACKFILL WITH SOIL AND TAMP IN 6" LAYERS. HOLE DIAMETER SHALL BE JUST WIDE ENOUGH TO ALLOW TAMPING. GUY AND ANCHOR INSTALLATION MUST BE APPROVED BY LOCAL ENGINEER. 4" SCREW ANCHOR MINIMUM GROUNDING ELECTRODE PER N.E.C.. OWNER PROVIDE AND INSTALL A. A ' CLASS 9 SOUTHERN YELLOW PINE (SYP) POLE OR A 6" X 6" SYP POST THAT IS PROPERLY TREATED WITH A WOOD PRESERVATIVE FOR EARTH CONTACT. SET POLE IN ACCORDANCE WITH OPTION A, B OR C. B. SERVICE ENTRANCE TO BE GROUNDED IN ACCORDANCE WITH N.E.C.. OWNER WILL INSTALL A. METER SOCKET IN ACCORDANCE WITH N.E.C.. SETTING DEPTHS FOR THE THREE OPTIONS ARE FOR 5 LB. ICE TENSIONS. 4. THIS DRAWING MAY BE USED FOR VARIOUS TYPES OF OVERHEAD SERVICES: A. OVERHEAD MOBILE HOME SERVICES B. NON-RESIDENTIAL SERVICES 8// SIMPSON SIMPSON ADCOCK /8/ SIMPSON SIMPSON ELKINS 7/8/ BURLISON GUINN ELKINS OVERHEAD SERVICE POLE 4.5-6
. ALL DIMENSIONS SHOWN ARE MINIMUM.. MINIMUM ' POLE REQUIRED. TALLER MAY BE NEEDED TO MEET SERVICE SAG REQUIREMENTS. MINIMUM 6' POLE ALLOWED IF SET WITHIN ' OF SOURCE COMPANY POLE.. ONE BRACE TO BE IN DIRECTION OF SERVICE. AT LEAST ONE ADDITIONAL BRACE TO BE LOCATED AT 9 TO DIRECTION OF SERVICE. 4. SOIL TO BE FIRMLY TAMPED AROUND POLE AND STAKES DRIVEN INTO FIRM EARTH. 5. CUSTOMER FURNISHES ALL ITEMS EXCEPT METER. THE METER BASE, WIRING, EQUIPMENT SERVICE EQUIPMENT GROUND ON THE POLE ARE TO BE INSTALLED BY THE CUSTOMER'S ELECTRICIAN IN ACCORDANCE WITH THE N.E.C AND LOCAL ORDINANCES. 6. SOLID, ONE PIECE, 4" X 4" WOOD POST MAY BE SUBSTITUTED WITH ENGINEER'S APPROVAL. 7. SERVICES SHALL NOT BE RUN TO TEMPORARY POLES NOT MEETING THE REQUIREMENTS SET FORTH HEREIN WITHOUT APPROVAL OF THE LOCAL ENGINEER ON SPECIFIC CASES. 8. HOUSE BRACKET MOUNTING LOCATION SHALL BE IN THE SIDE OF THE SERVICE POLE NOT IN THE TOP. 9. IF THE 4 FOOT MINIMUM DEPTH CANNOT BE OBTAINED DUE TO ROCK, TWO ADDITIONAL BRACES 9 DEGREES TO THE BRACES SHOWN MUST BE INSTALLED (FOUR BRACES TOTAL). IN NO CIRCUMSTANCES SHOULD THE EMBEDMENT DEPTH BE LESS THAN FEET. 8' '-" TO 5'-6" TREATED WOOD POLE WITH MIN. DIAMETER OF 4" '-6" MINIMUM ANYWHERE IN SPAN (8'-" MINIMUM IF OVER ROADS OR AREAS SUBJECT TO VEHICULAR TRAFFIC) WEATHERPROOF SWITCH BOX " X 4" BRACE GROUND WIRE 9 ALTERNATE BRACE LOCATION 9 FROM DIRECTION OF SERVICE 9 SEE NOTE PLAN VIEW DIRECTION OF SERVICE " X 4" BRACE GROUNDING ELECTRODE PER N.E.C. 6' 4' MIN. ' MIN. 6' ' MIN. SEE NOTE 9 " X 4" STAKES //4 SIMPSON GUINN ADCOCK 8// SIMPSON SIMPSON ADCOCK 4// SIMPSON SIMPSON ELKINS 6// BURLISON GUINN ELKINS TEMPORARY SERVICE POLE DEC DEM DEP DEF X 4.5-8
CATWALKS BILLBOARDS LADDER LOCATION LADDER LOCATION NO COMPANY SERVICE SHALL BE ATTACHED TO ANY PART OF THE CATWALKS SERVICE MASTHEAD AND RISER ' EXTENSION BRACKET (SUPPLIED BY CUSTOMER) ' MAX. COMPANY SERVICE WIRE ENTRANCE TO BE SPOTTED BY COMPANY ENGINEER PLAN VIEW BILLBOARD MASTHEAD COMPANY SERVICE WIRE ' EXTENSION BRACKET MUST PROVIDE REQUIRED SERVICE DROP CLEARANCES LADDER LOCATION SERVICE RISER SEE.- AND.- METER AND BASE FINAL GRADE '-" TO 5'-6" MT.HT. ELEVATION NOTE:. DO NOT PROVIDE SERVICE TO SIGN WHICH DOES NOT HAVE CLEARANCES FROM ADJACENT OVERHEAD CONDUCTORS AS REQUIRED BY N.E.S.C. AND ANY ADDITIONAL COMPANY SPECIFICATIONS. 8/6/4 EANES EANES ADCOCK 4// SIMPSON SIMPSON ELKINS 7/8/ BURLISON GUINN ELKINS BILLBOARD SERVICE ENTRANCE REQUIREMENTS METHOD "A" DEC DEM DEP DEF X 4.5-
BILLBOARD ' MIN. COMPANY SERVICE WIRE LADDER LOCATION SEE DWGS..- AND.- SERVICE RISER '-" TO 5'-6" MT. HT. METER AND BASE FINAL GRADE ELEVATION COMPANY SERVICE WIRE ' MIN. SERVICE RISER AND MASTHEAD STEEL POLE NO PART OF COMPANY SERVICE WIRE WILL BE RUN WITHIN ' OF LADDER OVERHEAD SERVICE WIRE MAY BE LOCATED ANYWHERE IN THIS AREA. CALL LOCAL COMPANY OFFICE FOR SERVICE ENTRANCE SPOTTING. ' MIN. PLAN VIEW 8/6/4 EANES EANES ADCOCK BILLBOARD SERVICE ENTRANCE REQUIREMENTS METHOD "B" DEC DEM DEP DEF X O 7/8/ BURLISON GUINN ELKINS 4.5-