Stump Grinders SSG2524 35276 328-215P Parts Manual Read the Operator's manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2014 Printed 08/14/14 Cover photo may show optional equipment not supplied with standard unit.
Table of Contents Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Section 2: Hitch & Arm Components...6 Hitch, Pivot & Arm...6 Section 3: Rotor Components...8 Rotor & Chute Components...8 Rotor Wheel Components...10 Section 4: Hydraulics...12 Hydraulic Cylinder (810-384C) Cross...12 Left/Right Rotate Hydraulics...14 Motor Drive Hydraulics S/N 859352-...16 Motor Drive Hydraulics S/N 859353+...18 Up/Down Tilt Hydraulics...20 Valve 2 Priority (810-840C)...22 Section 5: Labels...24 Label Placement...24 Section 6: Options & Accessories...26 14 Pin Connector Harnesses...26 Case Drain Coupler...28 Case Drain W/ Motor Guard S/N 859352-...30 Control Box (823-377C)...32 Control Harness...34 Control Harrness Kubota Skid W/ 2-Pin Power Supply...36 Couplers Quick Flat Faced...38 Wiring Harness 14 Pin...40 Wiring Harness 14 Pin JD...42 Wiring Harness 14 Pin JD Electric/Hydraulic...44...46 Copyright 2014. All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 SSG2524 Stump Grinders 328-215P 08/14/14
1 C H L M R U V W 14 Pin Connector Harnesses...26 Case Drain Coupler...28 Case Drain W/ Motor Guard S/N 859352-...30 Control Box (823-377C)...32 Control Harness...34 Control Harrness Kubota Skid W/ 2-Pin Power Supply...36 Couplers Quick Flat Faced...38 Hitch, Pivot & Arm...6 Hydraulic Cylinder (810-384C) Cross...12 Label Placement...24 Left/Right Rotate Hydraulics...14 Motor Drive Hydraulics S/N 859352-...16 Motor Drive Hydraulics S/N 859353+...18 Rotor & Chute Components...8 Rotor Wheel Components...10 Up/Down Tilt Hydraulics...20 Valve 2 Priority (810-840C)...22 Wiring Harness 14 Pin...40 Wiring Harness 14 Pin JD...42 Wiring Harness 14 Pin JD Electric/Hydraulic...44 Alphabetized Table of Contents 08/14/14 SSG2524 Stump Grinders 328-215P 3
4 SSG2524 Stump Grinders 328-215P 08/14/14
08/14/14 SSG2524 Stump Grinders 328-215P 5
Hitch, Pivot & Arm Section 2: Hitch & Arm Components 35277 6 SSG2524 Stump Grinders 328-215P 08/14/14
Hitch, Pivot & Arm Section 2: Hitch & Arm Components Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. dwg35277 328-200H 328-201H 328-202H 328-210H 328-211K 328-406D 328-434D 800-080C 802-057C 802-091C 802-138C 802-224C 803-084C 803-169C 803-255C 803-263C 804-007C 816-504C Drawing Image Number SKID HITCH STUMP GRINDER SWING WELD MOTOR LIFT WELD SKID SHOE WELD SKID SHOE ASSY PIVOT PIN SKID SHOE ADJUSTMENT GREASE ZERK 1/4-28 THD FORMING HHCS 5/8-11X2 1/4 GR5 HHCS 1/2-13X1 1/2 GR5 HHCS 5/16-18X2 1/4 GR5 HHCS 1/4-20X1 1/4 GR5 NUT HEX NYLOCK 5/16-18 PLT NUT HEX FLG LOCK 1/2-13 PLT NUT HEX NYLOCK 1/4-20 NUT HEX FLANGE LOCK 5/8-11 PLT WASHER FLAT 1/4 SAE PLT MANUAL STORAGE CONTAINER 08/14/14 SSG2524 Stump Grinders 328-215P 7
Rotor & Chute Components Section 3: Rotor Components 35278 8 SSG2524 Stump Grinders 328-215P 08/14/14
Rotor & Chute Components Section 3: Rotor Components Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. dwg35278 328-208K 328-209H 328-404D 328-436D 328-437D 802-010C 802-080C 803-084C 803-169C 803-229C 804-041C 816-759C Drawing Image Number ROTOR WHEEL ASSY ROTOR SHROUD WELD GUARD PIVOT RUBBER GUARD RETAINER CHIP GUARD HHCS 5/16-18X1 1/4 GR5 HHCS 7/16-14X1 GR5 NUT HEX NYLOCK 5/16-18 PLT NUT HEX FLG LOCK 1/2-13 PLT NUT HEX FLANGE LOC 7/16-14 PLT WASHER FLAT 7/16 SAE PLT CHIP GUARD RUBBER 08/14/14 SSG2524 Stump Grinders 328-215P 9
Rotor Wheel Components Section 3: Rotor Components 35279 10 SSG2524 Stump Grinders 328-215P 08/14/14
Rotor Wheel Components Section 3: Rotor Components Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. dwg35279 328-207H 820-493C 820-494C 820-495C 820-496C 820-497C 842-028C 328-108A Drawing Image Number ROTOR WHEEL WELD CUT TOOTH RH CARBIDE CUT TOOTH LH CARBIDE CUT TOOTH STRAIGHT CARBIDE CUT TOOTH MNT COUNTERBORE CUT TOOTH MNT THREADED HSHCS 5/8-18X2 1/4" SSG2524 SERVICE BLADE KIT 12 ea. of 820-493C & 820-494C & 8 ea. of 820-495C 08/14/14 SSG2524 Stump Grinders 328-215P 11
Hydraulic Cylinder (810-384C) Cross Section 4: Hydraulics 33918 12 SSG2524 Stump Grinders 328-215P 08/14/14
Hydraulic Cylinder (810-384C) Cross Section 4: Hydraulics Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. dwg33918 810-384C 1D1205-8 N/A 1D1401-300 N/A 1D0007-850 1D0206-1075 1D1157-17 N/A 2A0235-8 N/A 2A0580-1100 2A0246-12 1D1003-5 2A0079-616 2A0235-6 805-032C 1D1551-16275 810-009C Drawing Image Number CYL 3X6X1.25 ROD (TIE ROD) * CROSS, BASE CLEVIS CROSS, O-RING CROSS PISTON 3 BORE CYLINDER CROSS, BACK-UP CROSS, TUBE CROSS, ROD CROSS HEAD 3 BORE CYLINDER WIPER SEAL CROSS CROSS NUT, TIE ROD CROSS U-CUP CROSS,TIE ROD CROSS NUT, PISTON CROSS ROD CLEVIS CROSS SCREW, CAP CROSS NUT, CLEVIS & TIE ROD PIN HAIR COTTER.148 WIRE CROSS CLEVIS PIN CYL SEAL KIT 3 (CROSS) In Seal Kit Item #18 In Seal Kit Item #18 In Seal Kit Item #18 In Seal Kit Item #18 08/14/14 SSG2524 Stump Grinders 328-215P 13
Left/Right Rotate Hydraulics Section 4: Hydraulics 35283 14 SSG2524 Stump Grinders 328-215P 08/14/14
Left/Right Rotate Hydraulics Section 4: Hydraulics Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. dwg12345 810-384C 811-170C 811-171C 841-818C 841-819C Drawing Image Number CYL 3X6X1.25 ROD (TIE ROD) AD 9/16MORB 9/16MJIC EL 3/4MORB 9/16MJIC HH1/4R2 62.4 9/16FJIC HH1/4R2 55.12 9/16FJIC 08/14/14 SSG2524 Stump Grinders 328-215P 15
Motor Drive Hydraulics S/N 859352- Section 4: Hydraulics 35280 16 SSG2524 Stump Grinders 328-215P 08/14/14
Motor Drive Hydraulics S/N 859352- Section 4: Hydraulics Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. dwg35280 326-627A 328-435D 802-004C 802-082C 802-168C 803-169C 803-209C 803-255C 805-246C 810-715C 810-839C 810-840C 811-408C 811-411C 811-744C 811-745C 841-291C 841-676C 841-816C 841-817C 841-829C 841-876C Drawing Image Number COUPLERS, QUICK FLAT FACED SKID VALVE COVER HHCS 1/4-20X3/4 GR5 HHCS 1/2-13X1 3/4 GR5 HHCS 3/8-16X3 1/4 GR5 NUT HEX FLG LOCK 1/2-13 PLT NUT FLANGE LOCK 3/8-16 PLT NUT HEX NYLOCK 1/4-20 PIN COTTER 5/32 X 1 3/4 LG VALVE 3/4 IN-LINE CHECK HYD MOTOR VALVE 2 PRIORITY STUMP GRINDER AD 1 1/16MORB 1 1/16MJIC EL 1 1/16MJIC 1 1/16MORB CP 1 1/16FORB MALE QUICK CP 1 1/16FORB FEMALE QUICK AD 1 1/16MORB 1 1/16FJIC TEE 1.06FJIC 1.06MJIC 1.06MJIC HH3/4R16 117.5 1.06MOR1.06FJIC HH3/4R16 123.5 1.06MOR1.06FJIC HH3/4R16 18.6 1.06FJIC(1)90 HH3/4R16 10.75 1.06MJIC90FJIC Optional Optional Optional 08/14/14 SSG2524 Stump Grinders 328-215P 17
Motor Drive Hydraulics S/N 859353+ Section 4: Hydraulics 35952 18 SSG2524 Stump Grinders 328-215P 08/14/14
Motor Drive Hydraulics S/N 859353+ Section 4: Hydraulics Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. dwg35952 326-627A 328-290D 328-435D 802-004C 802-017C 802-082C 802-168C 803-169C 803-209C 803-255C 805-246C 810-715C 810-840C 811-408C 811-411C 811-744C 811-745C 841-291C 841-676C 841-816C 841-817C 841-829C 841-876C 850-007C 851-208C 851-209C 990-296R Drawing Image Number COUPLERS, QUICK FLAT FACED FITTING SHIELD SKID VALVE COVER HHCS 1/4-20X3/4 GR5 HHCS 3/8-16X1 GR5 HHCS 1/2-13X1 3/4 GR5 HHCS 3/8-16X3 1/4 GR5 NUT HEX FLG LOCK 1/2-13 PLT NUT FLANGE LOCK 3/8-16 PLT NUT HEX NYLOCK 1/4-20 PIN COTTER 5/32 X 1 3/4 LG VALVE 3/4 IN-LINE CHECK VALVE 2 PRIORITY STUMP GRINDER AD 1 1/16MORB 1 1/16MJIC EL 1 1/16MJIC 1 1/16MORB CP 1 1/16FORB MALE QUICK CP 1 1/16FORB FEMALE QUICK AD 1 1/16MORB 1 1/16FJIC TEE 1.06FJIC 1.06MJIC 1.06MJIC HH3/4R16 117.5 1.06MOR1.06FJIC HH3/4R16 123.5 1.06MOR1.06FJIC HH3/4R16 18.6 1.06FJIC(1)90 HH3/4R16 10.75 1.06MJIC90FJIC HYDRAULIC MOTOR 25 GPM HH1/4R2 139 7/16MJIC3/8MNPT AD 7/16MORB 7/16MJIC CORRUGATED LOOM, 3/8 ID Optional Optional Optional S/N + 08/14/14 SSG2524 Stump Grinders 328-215P 19
Up/Down Tilt Hydraulics Section 4: Hydraulics 35284 20 SSG2524 Stump Grinders 328-215P 08/14/14
Up/Down Tilt Hydraulics Section 4: Hydraulics Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. dwg35284 810-384C 811-170C 811-171C 841-820C 841-821C Drawing Image Number CYL 3X6X1.25 ROD (TIE ROD) AD 9/16MORB 9/16MJIC EL 3/4MORB 9/16MJIC HH1/4R2 8.36 9/16FJIC HH1/4R2 18.5 9/16FJIC 08/14/14 SSG2524 Stump Grinders 328-215P 21
Valve 2 Priority (810-840C) Section 4: Hydraulics 35860 22 SSG2524 Stump Grinders 328-215P 08/14/14
Valve 2 Priority (810-840C) Section 4: Hydraulics Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. dwg35860 810-840C 88400016 86020673 86020379 86020133 38400002 61010016 61010050 61010007 30103150 Drawing Image Number VALVE 2 PRIORITY STUMP GRINDER * DELTA PRESSURE COMPENSATOR DELTA RELIEF VALVE DELTA 4W3P SOLENOID VALVE DELTA CHECK VALVE DELTA 12 VDC COIL, WITH DIODE DELTA PLUG, #4 SAE, HEX SOC DELTA ORFICE PLUG (DIA.047) DELTA #6 SAE PLUG DELTA MANIFOLD 08/14/14 SSG2524 Stump Grinders 328-215P 23
Label Placement Table of Contents Section 5: Labels 35285 24 SSG2524 Stump Grinders 328-215P 08/14/14
Label Placement Section 5: Labels Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. dwg35285 818-339C 818-402C 818-798C 818-858C 838-107C 838-295C 848-088C 848-945C 858-009C Drawing Image Number DECAL WARNING HIGH PRESSUR SML DECAL GREASE 10 HRS RH DECAL WARNING PINCH POINT GEN DECAL CAUTION GENERAL SAFTEY DECAL DANGER THROWN OBJECT DECAL ROTATNG BLADE DT55 SW407 DECAL DANGER GUARD MISSING DECAL SSG2524 GOLD DECAL TREE STUMP GOLD 13" 08/14/14 SSG2524 Stump Grinders 328-215P 25
14 Pin Connector Harnesses Section 6: Options & Accessories 35475 26 SSG2524 Stump Grinders 328-215P 08/14/14
14 Pin Connector Harnesses Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. dwg35475 231-009 231-375 252-007 252-058 255-093 255-101 255-104 255-806 255-978 255-979 823-417C 823-418C 823-419C Drawing Image Number SHRINKTUBING.500" BLK SHRINKTUBING.375" BLK CABLE 5CON 18GA PVC GRY FASSE WIRE 18GA BLK WEATHERPACK CTR 2 PIN SHROUD CONT W/P SOCKET 18-20GA WEATHERPACK CNTR CABLE SEAL GR FASSE CONN DEUT HD30 PLG W/CBL FASSE CTR DEUTSCH SKT 16/18GA FASSE TRM CAVITY PLUG DEUT. DEUTSCH HD30 14 PIN 2 FUNCTION DEUTSCH HD30 14 PIN 2 FUNCTION DEUTSCH HD30 14 PIN 2 FUNCTION Harness A Harness B Harness C 08/14/14 SSG2524 Stump Grinders 328-215P 27
Case Drain Coupler Section 6: Options & Accessories 35963 28 SSG2524 Stump Grinders 328-215P 08/14/14
Case Drain Coupler Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. dwg35475 326-474A 800-060C 841-539C Drawing Image Number CTL/SS COUPLER PACKAGE CABLE TIE.19X14.25 3DIA 50LB CP 3/8 FEMALE QD 3/8FNPT 08/14/14 SSG2524 Stump Grinders 328-215P 29
Case Drain W/ Motor Guard S/N 859352- Section 6: Options & Accessories 35962 30 SSG2524 Stump Grinders 328-215P 08/14/14
Case Drain W/ Motor Guard S/N 859352- Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. dwg35962 328-109K 328-290D 802-017C 803-209C 851-208C 851-209C Drawing Image Number CASE DRAIN W/GUARD BNDL FITTING SHIELD HHCS 3/8-16X1 GR5 NUT FLANGE LOCK 3/8-16 PLT HH1/4R2 139 7/16MJIC3/8MNPT AD 7/16MORB 7/16MJIC 08/14/14 SSG2524 Stump Grinders 328-215P 31
Control Box (823-377C) Section 6: Options & Accessories 33091 32 SSG2524 Stump Grinders 328-215P 08/14/14
Control Box (823-377C) Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. dwg33091 823-377C 213-005 800-303C 219-007 219-009 250-007 250-023 255-092 255-093 255-098 255-102 255-103 255-104 255-186 259-001 259-004 259-005 304-345 Drawing Image Number CONTROL BOX SNOW BLOWER * FASSE WSHR RBR1ODX1/4IDX1/16TK CABLE TIE 2 DIA MIN - BLK FASSE SCR THUMB BLK 1/4-20X1/2 FASSE BRKT ALM 4.70 #1591C FASSE SW TOG DPDT 3P MOM SHORT FASSE SW TOG BOOT OPN BLK FASSE CNTR WP 2 PIN SHROUD WEATHERPACK CTR 2 PIN SHROUD CNTR WP 6 PIN SHROUD WEATHERPACK CTR MALE TRM 14/16 WEATHERPACK CNTR F TRM 14/16 WEATHERPACK CNTR CABLE SEAL GR CNTR WP CAVITY PLUG FASSE GROMMET.5000D SNAP FASSE SW TOG GRP VNYL WHT.187 FASSE SW TOG GRP VNYL RED.187 ECL 1591CBK/6060A-2X1/2SWSXTSX 08/14/14 SSG2524 Stump Grinders 328-215P 33
Control Harness Table of Contents Section 6: Options & Accessories 35246 34 SSG2524 Stump Grinders 328-215P 08/14/14
Control Harness Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. 6. dwg35246 370-134A 823-385C 823-385C 823-386C 823-405C 800-112C 823-377C Drawing Image Number CONTROL HARNESS SKID * HARNESS EXTENSION HARNESS EXTENSION HARNESS, POWER HARNESS SOLENOID 2 PRIORITY CABLE TIE.19X7.25 1.75D 50LB CONTROL BOX 2 PRIORITY 08/14/14 SSG2524 Stump Grinders 328-215P 35
Control Harrness Kubota Skid W/ 2-Pin Power Supply Section 6: Options & Accessories 37145 36 SSG2524 Stump Grinders 328-215P 08/14/14
Control Harrness Kubota Skid W/ 2-Pin Power Supply Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. 4. 5. dwg37144 370-434A 823-439C 823-377C 823-385C 823-405C 800-112C Drawing Image Number CONTROL HARNESS KUBOTA SKID HRN DTP04-2P 14GA 2WPS /5' CONTROL BOX 2 PRIORITY HARNESS EXTENSION HARNESS SOLENOID 2 PRIORITY CABLE TIE.19X7.25 1.75D 50LB 08/14/14 SSG2524 Stump Grinders 328-215P 37
Couplers Quick Flat Faced Section 6: Options & Accessories 35292 38 SSG2524 Stump Grinders 328-215P 08/14/14
Couplers Quick Flat Faced Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. dwg35292 326-627A 811-744C 811-745C Drawing Image Number COUPLERS, QUICK FLAT FACED CP 1 1/16FORB MALE QUICK CP 1 1/16FORB FEMALE QUICK 08/14/14 SSG2524 Stump Grinders 328-215P 39
Wiring Harness 14 Pin Section 6: Options & Accessories 35289 40 SSG2524 Stump Grinders 328-215P 08/14/14
Wiring Harness 14 Pin Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. dwg35289 370-336A 800-060C 823-417C Drawing Image Number WIRING HARNESS 14 PIN CABLE TIE.19X14.25 3DIA 50LB DEUTSCH HD30 14 PIN 2 FUNCTION 08/14/14 SSG2524 Stump Grinders 328-215P 41
Wiring Harness 14 Pin JD Section 6: Options & Accessories 35290 42 SSG2524 Stump Grinders 328-215P 08/14/14
Wiring Harness 14 Pin JD Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. dwg35290 370-337A 800-060C 823-418C Drawing Image Number WIRING HARNESS 14 PIN JD CABLE TIE.19X14.25 3DIA 50LB DEUTSCH HD30 14 PIN 2 FUNCTION 08/14/14 SSG2524 Stump Grinders 328-215P 43
Wiring Harness 14 Pin JD Electric/Hydraulic Section 6: Options & Accessories 35291 44 SSG2524 Stump Grinders 328-215P 08/14/14
Wiring Harness 14 Pin JD Electric/Hydraulic Section 6: Options & Accessories Ref. Part No. Part Description Comments Revision 1. 2. 3. dwg35291 370-338A 800-060C 823-419C Drawing Image Number WIRING HARNESS 14 PIN JD EH CABLE TIE.19X14.25 3DIA 50LB DEUTSCH HD30 14 PIN 2 FUNCTION 08/14/14 SSG2524 Stump Grinders 328-215P 45
The is a numeric index of all part numbers included in this manual. The index shows what page(s) the part is used on. Part Number Page Part Number Page Part Number Page 1D0007-850...13 1D0206-1075...13 1D1003-5...13 1D1157-17...13 1D1205-8...13 1D1401-300...13 1D1551-16275...13 213-005...33 219-007...33 219-009...33 231-009...27 231-375...27 250-007...33 250-023...33 252-007...27 252-058...27 255-092...33 255-093...27, 33 255-098...33 255-101...27 255-102...33 255-103...33 255-104...27, 33 255-186...33 255-806...27 255-978...27 255-979...27 259-001...33 259-004...33 259-005...33 2A0079-616...13 2A0235-6...13 2A0235-8...13 2A0246-12...13 2A0580-1100...13 30103150...23 304-345...33 326-474A...29 326-627A...17, 19, 39 328-108A...11 328-109K...31 328-200H...7 328-201H...7 328-202H...7 328-207H...11 328-208K...9 328-209H...9 328-210H...7 328-211K...7 328-290D...19, 31 328-404D...9 328-406D...7 328-434D...7 328-435D...17, 19 328-436D...9 328-437D...9 370-134A...35 370-336A...41 370-337A...43 370-338A...45 370-434A...37 38400002...23 61010007...23 61010016...23 61010050...23 800-060C...29, 41, 43, 45 800-080C...7 800-112C...35, 37 800-303C...33 802-004C...17, 19 802-010C...9 802-017C...19, 31 802-057C...7 802-080C...9 802-082C...17, 19 802-091C...7 802-138C...7 802-168C...17, 19 802-224C...7 803-084C...7, 9 803-169C...7, 9, 17, 19 803-209C...17, 19, 31 803-229C...9 803-255C...7, 17, 19 803-263C...7 804-007C...7 804-041C...9 805-032C...13 805-246C...17, 19 810-009C...13 810-384C...13, 15, 21 810-715C...17, 19 810-839C...17 810-840C...17, 19, 23 811-170C...15, 21 811-171C...15, 21 811-408C...17, 19 811-411C...17, 19 811-744C...17, 19, 39 811-745C...17, 19, 39 816-504C...7 816-759C...9 818-339C...25 818-402C...25 818-798C...25 818-858C...25 820-493C...11 820-494C...11 820-495C...11 820-496C...11 820-497C...11 823-377C...33, 35, 37 823-385C...35, 37 823-386C...35 823-405C...35, 37 823-417C...27, 41 823-418C...27, 43 823-419C...27, 45 823-439C...37 838-107C...25 838-295C...25 841-291C...17, 19 841-539C...29 841-676C...17, 19 841-816C...17, 19 841-817C...17, 19 841-818C...15 841-819C...15 841-820C...21 841-821C...21 841-829C...17, 19 841-876C...17, 19 842-028C...11 848-088C...25 848-945C...25 850-007C...19 851-208C...19, 31 851-209C...19, 31 858-009C...25 86020133...23 86020379...23 86020673...23 88400016...23 990-296R...19 dwg12345...15 dwg33091...33 dwg33918...13 dwg35246...35 dwg35277...7 dwg35278...9 dwg35279...11 dwg35280...17 dwg35284...21 dwg35285...25 dwg35289...41 dwg35290...43 dwg35291...45 dwg35292...39 dwg35475...27, 29 dwg35860...23 dwg35952...19 dwg35962...31 dwg37144...37 N/A...13 46 SSG2524 Stump Grinders 328-215P 08/14/14
This Page Intentionally Left Blank 08/14/14 SSG2524 Stump Grinders 328-215P 47
Great Plains Manufacturing, Inc. Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com