BY DAYTON SUPERIOR FormRight FORMING SYSTEM
System Design The FormRight concrete forming system is a modular design suitable in handset or gangform applications. Modular versatility Panels come in 23 different sizes and can be combined vertically or horizontally to create almost any dimension. A full line of accessories and hardware makes configuring gangs and setting details quick and simple. Rapid Clamps eliminate the need for walers even when moving large gangs. The Adjustable Aligning Clamp, Outer Corner Clamp and Strongback Clamp make panel connections for common details as fast and easy as standard panel connection. System strength FormRight panels are manufactured with rust resistant hot-dipped galvanized or dip painted steel frames. The form face is a 14 mm (½") plywood with a phenolic resin overlay on both sides to provide a high quality concrete finish and extended panel life. Panels, clamps and ties are designed to withstand 60 kn/m 2 (1250 psf) of concrete pressure and are fully compatible with the Rasto forming system. 2 WWW.SYMONS.COM
Panels FormRight panels are clamped together to create almost any wall or column dimension. They can also be stepped to accommodate uneven footing or slab elevations. Panel sizes FormRight panels come in heights from 270 cm to 150 cm (9'-10" to 4'-11" nominal). Widths from 90 cm to 30 cm (36" to 12") are available in most heights. 240 cm x 90 cm, 240 cm x 60 cm and 240cm x 30 cm panels are available for stacking with Giant panels. Gangform productivity Giant Panels are available for forming large walls. Their 240 cm wide and 270 cm high (7'-10" x 8'-10") size makes creating large gangs very fast, and reduces the materials required. This large panel option is a great way to boost productivity! Handset capability The 270 cm x 75 cm (8' -10" x 2'-6") panel and smaller sizes are also frequently utilized in handset applications. The panels quickly clamp together to create one of the fastest setting handset systems. Giant Panel (240cm x 270cm) 800-800-SYMONS 3
Clamps and Connectors Aligning Panel Clamp In one operation, the Rapid Clamp FR aligns panels and clamps them into postition with flush, tight joints. It straddles the panel crossmembers to provide vertical alignment and eliminates the need for walers in most common applications. Adjustable Aligning Clamp The Adjustable Aligning Clamp spans fillers up to 15 cm (6") wide and provides support for extension panels. Rapid Clamp FR Typical Clamp Application Outer Corner Clamp StrongBack Clamp The Strongback Clamp quickly stiffens and aligns tall FormRight gangs with stacking panels. A Strongback End Clamp attaches to the Strongback Clamp for tall face up gang assembly. Outer Corner Clamp The Outer Corner Clamp connects two panels to form a 90 outside corner. Adjustable Clamp Strongback Clamp Waler Spanner 30 and Tension Nut Strongback End Clamp Accessory Bolt Nuts and Bolts The Centering Tension Bolt distributes loads evenly across the FormRight profile. The Centering Tension Bolt Nut 100 centers itself evenly in the FormRight profile. They connect panels to hinged corners, mounting bulkheads and other applications. The FormRight Accessory Bolt is utilized with Outside Conversion Corners, Filler Angles and Column Hinges. Waler Spanner The Waler Spanner (30) with the Waler Spanner Tension Bolt connect Multi-Purpose Walers and Adjustment Walers to panels. Centering Tension Bolt and Centering Tension Nut 100 4 WWW.SYMONS.COM
Corners Most FormRight corners are formed using standard FormRight panels, Inside Corner Panels and Rapid Clamps. Other components provide additional form layout options that create an adaptable, productive system. Inside Corner The 30 cm (12" nom.) wide Inside Corner is available in 150 cm, 270 cm and 300 cm heights. Unlatching the stiffener flexes the corner, allowing it to be reduced by approximately 2 degrees to aid stripping. Outside Corners Outside Corners are attached to panels with Accessory Bolts and Centering Nuts. Typical Inside Corner Configuration Hinged Corners The 15 cm (6" nom.) wide Hinged Corner creates corner angles of 90 to 300. The 30 cm (12" nom.) wide Hinged Corner forms corner angles from 60 to 150. Both are available in 150 cm, 270 cm and 300 cm (4'-11", 8'-10" and 9'-10") heights. Three-Piece Stripping Corner The inside stripping corner allows core walls to be set and stipped without disassembling the gangs. The corner consists of three pieces which paritally disconnect and slide inward with ratched turnbuckles at the top and bottom of each gang. Outside Conversion Corner Outside Conversion Corner The Outside Conversion Corner converts metric panel dimensions to U.S. (Imperial) column widths. It requires the Accessory Bolt and Centering Nut to complete the attachment. Outside Corners Column Hinge The Column Hinge allows FormRight column form halves to fly as a single unit. It requires two Centering Nuts to complete the attachment. Column Hinge Hinged Corners 800-800-SYMONS 5
Ties and Accessories Taper Tie She Bolt Tie Rod Tie Sleeve, Cones and Plugs Tie Holding Clip 15mm x 4" x 6" Tie Plate and Nut Frame Tie Plate FormRight panel design includes reinforced tie holding bays located next to the edge profiles. If a tie is not inserted in a holding bay, a Panel Plug is inserted to fill the tie hole. One tie nut typically supports adjacent panels. Taper Ties Taper Ties are 15 mm ( 5 /8") diameter and come in lengths to accommodate wall diameters from 7" to 39". The same size standard Tie Nut is used on both ends of the Taper Tie to simplify hardware needs. She Bolts These reusable outer tie units are used with a cut-to-size 5 /8" inner unit and standard Tie Nuts. Tie Rods The reusable Tie Rods are available in 6" increments and are used in combination with Sleeves and Cones. Sleeves are cut-to-length and Cones are added to ensure the proper spacing between the two erected forming faces. Tie Sleeve Plugs close the openings left in the wall. Tie Holding Clip The Tie Holding Clip holds the Tie Rod away from the form in dry tie applications (i.e.: top ties and bulkheads). Tie Nuts The Swivel Tie Nut (85) pivots up to 10 for bat - tered walls and other applications. It includes a swivel bearing plate. The standard Tie Nut does not pivot, but is used in most applications. Frame Tie Plate The Frame Tie Plate is used at panel corners to cover the joint where all four corners meet and provide support for certain applications. Tie Nut Ratchet The Tie Nut Ratchet is utilized to install and tighten tie nuts and hardware. Tie Nut Ratchet 6 WWW.SYMONS.COM
Walers Two Hinged Waler 170s are required to form a complete hinged waler assembly for nonrectangular corners. Each Hinged Waler 170 includes a Pivot Pin. An Adjustment Waler 120 provides length adjustments and is typically used for creating bulkheads. The Multi-Purpose Waler 100 is used like the Adjustment Waler 120, and can be used to create tension resistant filler alignment. It also features holes for nailing. Hinged Waler 170 Adjustment Waler 120 Multi-Purpose Waler 100 Lift Brackets The RTL Lift Bracket has a maximum load capacity of 1,100 pounds. A minimum of two lift brackets are required to lift a gang of up to 265 ft 2. Note: The actual total area will depend on the total weight of the panels and hardware. Caution: The angle for the attached lifting lines must be greater than or equal to 60 degrees from horizontal. If they are less than 60 degrees, or if more than two brackets are used, a spreader beam must be used. Column Lift Brackets can be used with Outside Conversion Corners to provide convenient lifting points. Core Forming Shaft Spindle Brackets provide attachment points for spindle braces commonly used to retract interior forms in core wall forming. Leveling Devices provide level adjustment of core formwork prior to placing concrete. They require 1.90" diameter screw jacks. RTL Lift Bracket Column Lift Bracket Shaft Spindle Bracket Leveling Device 800-800-SYMONS 7
BY DAYTON SUPERIOR 2400 Arthur Avenue Elk Grove Village, IL 60007 USA 847-298-3200 FAX847-635-9287 www.symons.com info@symons.com 800-800-SYMONS Adjustable Column Form Form square or rectangular columns effi ciently with a minimum number of steel panels. Alisply Clamp-type, metric-dimension system is quickly assembled and reconfi gured for fast-paced gangforming. Aluminum Beams and Joists Lightweight beams/ joists from 4' to 30' (122cm to 914cm) for deck or gangform applications. Box Culvert Traveler Rolling steel framework is compatible with Steel-Ply, Versiform and Max-A-Form systems. Chemicals Liquid, cement, epoxy and other specialty products for concrete construction and repair. DeckFast A quick two-component system of modular panels and shores for creating fl at concrete decks. Flex-Form Specially designed steel-faced system for forming curved walls and round tanks with no surface chording. Form Liner More than 100 standard patterns, in four different materials, create unique concrete textures. FormRight The advantages of a clamp-type gangform, with the handset fl exibility for details. FrameFast Provides 24,000 lb. (106kN) load capacity per shore frame with spacings from 3' to 15' (91.4cm to 457.2cm). Garage Beam A complete system to form an economical, pouredin-place concrete parking garage. Max-A-Form A durable, all-steel forming system that is ideal for pier caps and self-spanning applications. Resi-Ply A low cost, 1 1 8" (2.9cm) plywood forming system for residential construction, in 4-bar, 5-bar and 6-bar spacing. Roller Deck Column-mounted deck support system replaces conventional shoring, providing access for other trades. Room Tunnel One room per day, per form provides maximum forming productivity for repetitive room designs like hotels. ShorFast High capacity aluminum leg and jack shoring system can support up to 30 kips (133kN) per leg. Steel-Ply The most recognized modular system, with more than 80 panel and fi ller sizes, for handsetting or gangforming. Street Smart Reusable steel forms for residential curb and gutters, industrial slabs and highway paving applications. Symons Silver A lightweight aluminum system that makes residential forming operations effi cient and productive. Symons Soldier The next generation construction beam that can be used as a brace, strongback, waler or shore. Truss Crane handling of large aluminum tables increases deck forming productivity for repetitive bays. Versiform Steel frame/plywood face gangforming system that provides a smooth concrete fi nish. Printed in U.S.A. 2008, Symons Product Code 91206