1. Carbonators and Accessories 2. Water Boosters and Accessories 3. Water Filtration Systems and Replacement Filters 4. Water Bottle Dispensing System Lancer Carbonators and Components Known for its superior quality and reliability, the Turbo heavy duty, high capacity carbonator has a 100 GPH (379 LPH) pump, ideal for fast flow valves. With 60 F inlet water it will provide a carbonation level of 6.0. With 75 F inlet water it will provide a carbonation level of 5.5, and at maximum flow 5.3. Turbo has solid state electronics, a built-in advanced diagnostics system, ASSE approved vented check valve, stainless steel base with rubber feet, 3/8" male barb inlets and dual 3/8" male flare soda outlets. Dimensions: 12.25"W x 12.5" H x 14.25" D. Shipping weight: 35 lbs. Number Description 85192300 Carbonator, fast flow with vented check valve (VCV) 85192701 Carbonator, recirculating system 520590/01 Probe assembly, fast flow, Turbo 520206 Probe assembly, universal 64500054 Liquid level control board, universal 520001 Proximity switch assembly 540007/01 Carbonation tester kit Lancer Turbo carbonator 520590/01 520206 64500054 520001 540007/01 SHURflo High Pressure Electric Carbonator 8005 Series, positive displacement, open flow, 3 chamber diaphragm pump is self-priming and can run dry without damage. Comes with ground wires and base plate. Flow rate: 1.4 GPM. Operating pressure: 100 psi. 115V. Number Description 8005932260 Carbonator, high pressure, 100 psi, 1.4 GPM Continuing product improvements may necessitate E-1
McCann s Carbonators and Components McCann s carbonators produce 100 GPM, have Diamond Bright tanks, brass water pumps, and encapsulated electronics to prevent moisture damage. Base is injection molded with press-in rubber feet to reduce noise. Heat sink probe caps prolong probe life, 2-piece probe design simplifies diagnostics, and there s no need to shut off the water or CO 2 for service. To test the 2-piece float probe: remove the probe electronics, pass the tip of a magnetic screwdriver past the lower end of the tube. If the reed switch closes, it is operating properly. The 2-piece probe has a five year warranty. Recirculating cold carb system maintains temperature at 30-33 F for optimum carbonation levels, and can be easily retrofit any installed dispenser system. E400397 All carbonators are 1/3 HP, 7.0 amps, 115/60/1, have ASSE 1022 backflow preventors, vented check valves, 1/4" MF CO 2 inlet, 3/8" MF water inlet and 3/8" MF soda water outlet(s). Number Low Lead Description E400397 E480397 Big Mac carbonator 13.5" W x 10.5" H x 12.75" D 436002 436802 Standard carbonator 9" W x 11" H x 11.5" D 435602 435802 Carbonator-in-a-box 12.25" W x 15" H x 6.5" D 153127 153127LL Recirculating cold carb system 25" W x 15" H x 18" D Tank 2 gals. 2 32 oz. 1 32 oz. 1 2 gals. 2 Soda Outlets 436002 McCann s Carbonator Components Number Description 161404 Float and probe assembly 161441 Probe kit and mounting studs 162115 Probe only 051374 2 male prong to 3 female prong adaptor cord/plug 051373 3 female prong cord/plug 152088 Power cord assembly (18/3), 8' 160856 Carb pump saver with lamp 190031 Pressure relief valve for carb tank, 180 psi 000868 Check valve, single, 1/4" MFL 000867 Check valve, double, 1/4" MFL 435602 E202397 recirculating cold carb system 001217 Carbonator foot (for bases) 161404 162115 190031 E-2 Continuing product improvements may necessitate
McCann s Carbonator Components Continued Number Description E400397 153100 Water inlet & nut assembly, plastic base 153018 Water inlet tubing assembly, 3/8", ASSE 1022 151319 Carbonator tank assembly, large w probe, 2 out 151318 Carbonator tank assembly w decals, large, 2 out 153095 Carbonator tank assembly, weld complete, 2 out 150538 Carbonator tank, small, 3/8 out, w decals & stud Back Flow Preventors A vented backflow preventor will provide pressure relief if the primary check valve fails, ensuring that the secondary check valve will remain closed. Plumbing codes in most states require that a ASSE standard 1022 vented backflow preventer is used on all carbonated beverage dispensers. Those with an internal ASSE 1032 non-vented check valve must have an ASSE 1022 check valve installed on the dispenser water line. 190897 61657 DS470DVV66X DS470DVV6F6X DS47066 161522 Number Type Description Fitting 190897 ASSE 1022 ABF-1 brass check valve, low lead 190944 ASSE 1022 ABF-1 brass check valve w 1/8" vent, low lead 61678 ASSE 1022 Watts SD-3 check valve 3/8" MF 61657 ASSE 1022 Watts SD-3 check valve with strainer 3/8" MF 61655 ASSE 1022 Watts SD-2 double check valve 3/8" MF S2722 ASSE 1022 Vent tube fitting 1/8" barb 161521 ASSE 1022 McCann s E3000 conversion kit 161522 ASSE 1022 McCann s E2000 conversion kit 161527 ASSE 1022 McCann s 43 Series conversion kit S470DVV66X ASSE 1032 Double check with vent 3/8" MF S470DVVP66X ASSE 1032 Double check with vent 3/8" MPT x 3/8" MF S470DVV6F6X ASSE 1032 Double check with vent stem 3/8" MF x 3/8" FF S470D66 SS Ball Double ball check valve 3/8" MF S470DH4H4 SS Ball Double ball check valve 1/4" barb S470DFP4P4 SS Ball Double ball check valve 1/4" FNPT x 1/4" NPT S47066 SS Ball Single ball check valve 3/8" MF S470H6H6 SS Ball Single ball check valve 3/8" barb Continuing product improvements may necessitate E-3
Carbonator Pumps Rotary vane pumps move potable water to beverage dispensers. Models with strainers have removable caps for periodic cleaning (every four months under normal conditions). Inlet and outlet ports are 3/8" NPT threaded. Some states require low or lead-free metals. The products listed below are the most commonly ordered part numbers. For additional pump options call ABS customer service. Fluid-O-Tech PA350X Fluid-O-Tech PA350 Fluid-O-Tech PA310X Fluid-O-Tech PA801 Number Procon Series 1 Procon Series 2 Procon Series 3 Procon Series 4 Low Lead Number Series Brass or SS GPH PSI Strainer Bypass Adj./ Releif Valve Brand PA350X250 PB350X250 PA Brass 125 250 Yes Yes Fluid-O-Tech 111A100F11AA250 111A100F11AA250LL 1 Brass 100 250 Yes Yes Procon 111A125F11AA250 111A125F11AA250LL 1 Brass 125 250 Yes Yes Procon PA3501250 PB3501250 PA Brass 125 250 No Yes Fluid-O-Tech 112A100F11AA170 112A100F11AA170LL 2 Brass 100 170 No Yes Procon 112A050F11AB100 112A050F11AB100LL 2 Brass 50 100 No Yes Procon 112E100F11BA170 112E100F11BA170LL 2 Brass 100 170 No Yes Procon PA110100 PB110100 PA Stainless Steel 50 100 No No Fluid-O-Tech PA310100 PB310100 PA Stainless Steel 100 100 No No Fluid-O-Tech 113A025F31XX 113A025F31XXLL 3 Stainless Steel 25 N/A No No Procon PA111100 PB111100 PA Stainless Steel 50 100 No Yes Fluid-O-Tech PA311100 PB311100 PA Stainless Steel 100 100 No Yes Fluid-O-Tech 113A050F31AB 113A050F31ABLL 3 Stainless Steel 50 100 No Yes Procon 113A100F31AA 113A100F31AALL 3 Stainless Steel 100 170 No Yes Procon 113A100F31AAT 113A100F31AATLL 3 Stainless Steel 100 170 No Yes Procon PA801240 PB801240 PA Brass 240 240 Yes Yes Fluid-O-Tech 114B240F11BA 114B240F11BALL 4 Brass 240 250 No Yes Procon E-4 Continuing product improvements may necessitate
Carbonation Testers Proper carbonation is critical to soft drink quality. During preventive maintenance several soft drink samples are poured into the chilled tester. Pressure and temperature are recorded and cross-referenced with the table on the canister to determine the current carbonation volume, and whether or not the carbonation needs adjustment. Pepsi carbonation tester Carbonator s and Accessories 161459 161480 CM1FJ CM3FJ Lancer carbonation tester 1143 26A 263A 67701 4406 Number Description 2701 Pepsi carbonation tester, complete assembly 270110A Pepsi carbonation tester, thermometer assembly 27013A Pepsi carbonation tester, relief valve assembly 2701200A Pepsi carbonation tester, canister assembly 2701A10 Pepsi carbonation tester, cap (must be purchased with gasket) 45001100 Pepsi carbonation tester, gasket with adhesive, for cap 270112 Pepsi carbonation tester, gauge 0-30 psi 600GP Pepsi carbonation tester, gauge protection boot 540007/01 Lancer carbonation tester, complete assembly 220025 Lancer carbonation tester, thermometer assembly 010767 Lancer carbonation tester, vent valve stem 010768 Lancer carbonation tester, vent cap 010814 Lancer carbonation tester, housing 011013 Lancer carbonation tester, adapter 020108 Lancer carbonation tester, seal 050112/02 Lancer carbonation tester, cap 160050 Lancer carbonation tester, gauge 4406 1/3 HP carbonator motor, welded base, 115V 4805 1/3 HP GE carbonator motor, 115/230V (dual) 101649 1/3 HP carbonator motor, welded base, 8 ft. harness, 115V 101647 1/3 HP carbonator motor, resilient base, 8 ft. harness, 115V 17849 1/3 HP carbonator motor, H682, carb ball bearing 1138 Strainer screen for Series 1 Procon pump 1143 Coupling ring for Procon pump 10451 Pressure spring G000520 Insulation cover for Series 3 Procon pump 011779W Insulation cover right side for Series 1 Procon pump 011910 Insulation cover left side for Series 1 Procon pump 161459 Carbonator/water booster floor stand, stainless 161480 Carbonator/water booster wall or rack mount shelf, stainless CM1FJ Carbonator/water booster floor stand, black CM3FJ Carbonator/water booster wall or rack mount shelf, black 103197 26A Watts water regulator, 3-50 psi, no gauge port, 3/8" FNPT 103200 26A Watts water regulator, 10-125 psi, no gauge port, 3/8" FNPT 0328060 263A Watts water regulator, 0-125 psi, 1/4" MPT gauge port, 3/8" FNPT 67701 5 gallon accumulator tank Continuing product improvements may necessitate E-5
Water Booster Systems Water boosters provide consistent water pressure to beverage dispensing systems, ensuring optimum performance. Gas-Driven Boosters Flojet K56 system has a 1/2 gallon accumulator tank, quick disconnect ports, and exhuast muffler for quiet operation. It is self-priming, supplies up to 4 GPM, and operates 60-90 psi. Dimensions: 12" H x 11.5" W x 7" D. 1 year warranty. Flojet G56 pump operates quietly and supplies up to 4 GPM. If pumping over 1.7 GPM a pulsation dampener or accumulator tank should be used to reduce pulsation due to momentary shifts in flow requirements. Operates 20-90 psi. Dimensions: 5.27" H x 3.21" W x 4.58" D. Weight: 1.24 lbs. 1 year warranty. G56 pump K56 system Number Description Product Inlet Product Outlet Gas Inlet K561030A K56 water boost system w 1/2 gal tank 1/2" barbed straight plastic 1/2" barbed straight nylon 1/4" CO 2 shutoff brass G561215A G56 water pump, stand-alone or 1/2" barbed straight plastic 1/2" barbed straight plastic 1/4" CO 2 shutoff brass replacement pump for K56 system 20793100 G56 pump muffler port N/A N/A N/A 20799100 K56 1/2 gallon bladder tank N/A N/A N/A Fully Automatic Electric Boosters Typically used when pumping from a cistern, water storage tank, or other ground water source. Both 2820 and 2840 Series have an accumulator tank, built-in inlet strainers, pressure switches and check valves. Dimensions: 11" W x 7" H x 11.5" D. 115V. 1 year warranty. 2820 and 2840 system Number Description Product Inlet/Outlet PSI GPM 2820040A 2820 Series, 115V 3/8" FPT 0-70 1.5 2840010A 2840 Series, 115V 1/2" OD or 3/4" OD hose barb 0-40 3.5 2840000A 2840 Series, 115V 1/2" OD or 3/4" OD hose barb 0-40 4.5 2840100A 2840 Series, 24V 1/2" OD or 3/4" OD hose barb 0-45 4.5 E-6 Continuing product improvements may necessitate
Triplex Water Booster System Triplex has a 4 gallon stainless steel tank, provides 1.4 GPM, and up to 100 psi outlet. Its advanced pump technology provides high efficiency, increased drawdown time, and extended life. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. Operating temperature: 40-120 F. Pump inlet: 3/8" hose barb. Tank discharge port: 1/2" hose barb. 115V. Triplex Water Booster/Water Delivery Pumps The Triplex High Pressure diaphragm pumps are self-priming and can run dry without harm. They are intended for intermittent duty cycles but can be run continuously for short periods of time. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. 115V. 1 year warranty. Duplex II Water Booster/Water Delivery Pumps The self-priming Duplex II Series with new diaphragm design, new valves, built-in back flow preventer, heavy-duty ball bearings and motor have been designed for maximum efficiency and long life. 115V. AC Variable Speed Drive (VCD) Pumps The AC VCD constant pressure pump matches motor speed to system demand to provide stable flow and reduced amp draw, eliminating unwanted pump switch cycling and the need for an accumulator tank. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. 115V. 1 year warranty. Number Description Water Inlet Water Outlet PSI GPM 2830000A Triplex booster system 3/8" barb 1/2" barb 100 1.4 03710042A Triplex Series 3/8" FPT 3/8" FPT 100 1.4 03810042A Triplex Series 3/8" FPT 3/8" FPT 150 1.4 D4821H4011A Duplex II Series 3/8" FPT 3/8" FPT 45 2.2 D4831H5011A Duplex II Series 3/8" FPT 3/8" FPT 60 2.2 D4834H6011A Duplex II Series 3/8" FPT 3/8" FPT 80 2.2 D4834H7011A Duplex II Series 3/8" FPT 3/8" FPT 100 2.2 04524043A AC VCD with 3 wires 5.0 04524500A AC VCD cable with plug 5.0 Continuing product improvements may necessitate E-7
Flojet Water Booster Accessories Number Description 01752300C Inline water regulator, 50 psi, QD connect, no ports 01752302C Inline water regulator, 50 psi, QD connect, 3/8" hose barb ports 01752320C Inline water regulator, 30 psi, QD connect, no ports 01752322C Inline water regulator, 30 psi, QD connect 3/8" hose barb ports 188100000 Accumulator tank, 1 gallon, 3/4" MPT openings, no fittings 20799000A Accumulator tank,.60 gallon, 3/4" MPT openings, no fittings 30573001 Accumulator tank, 125 psi,1 quart/liter capacity, 1/2" barb fittings 305730002B Accumulator tank, rubber valve, 125 psi, 1/2 quart/liter capacity, 1/2" barb fittings 305730012B Accumulator tank, metal valve, 125 psi, 1/2 quart/liter capacity, 1/2" barb fittings 188100000/ 20799000A 30573001 Flojet Water Booster/Pump Fittings Inline water regulators 305730002B/ 305730012B 21000131A 21000130A 20381002 20381026 20381009 20371024 21000229B 21000228B 91010004 91010053 91010003 91010052 Number Application Pump Series Barb Size Shape Material Additional Info 21000131A Inlet/Outlet G56 & K56 1/4" Straight hose barb Stainless steel 21000130A Inlet/Outlet G56 & K56 3/8" Straight hose barb Stainless steel 20381002 Inlet/Outlet G56 & K56 1/2" Straight hose barb Plastic/Celcon 20381026 Inlet/Outlet G56 & K56 1/2"-3/8" Straight hose barb Plastic/Celcon 20381009 Inlet/Outlet G56 & K56 1/2" Elbow hose barb Plastic/Celcon 20381024 Inlet/Outlet G56 & K56 1/2"-3/8" Elbow hose barb Plastic/Celcon 21000228B Inlet/Outlet G56 & K56 1/4" Straight Plastic John Guest 21000229B Inlet/Outlet G56 & K56 3/8" Straight Plastic John Guest 21000230B Inlet/Outlet G56 & K56 1/2" Straight Plastic John Guest 91010002 Inlet/Outlet Duplex II & 2820 3/8" x 3/8" Straight, MPT x barb Plastic 91010004 Inlet/Outlet Duplex II & 2820 1/4" x 3/8" Straight, MPT x barb Plastic 91010006 Inlet/Outlet Duplex II & 2820 3/8" x 1/2" Straight, MPT x barb Plastic 91010032 Inlet/Outlet Duplex II & 2820 3/8" x 1/4" Straight, MPT x barb Plastic 91010053 Inlet/Outlet Duplex II & 2820 1/4" x 1/4" Straight, MPT x barb Plastic 91010001 Inlet/Outlet Duplex II & 2820 3/8" x 3/8" Elbow, MPT x barb Plastic 91010003 Inlet/Outlet Duplex II & 2820 1/4" x 3/8" Elbow, MPT x barb Plastic 91010005 Inlet/Outlet Duplex II & 2820 3/8" x 1/2" Elbow, MPT x barb Plastic 91010033 Inlet/Outlet Duplex II & 2820 3/8" x 1/4" Elbow, MPT x barb Plastic 91010052 Inlet/Outlet Duplex II & 2820 1/4" x 1/4" Elbow, MPT x barb Plastic E-8 Continuing product improvements may necessitate
McCann s Water Boosters McCann s electric water boosters have stainless steel tanks and fittings, pre-charged bladders and relief valves. Flow rates up to 100 GPH. Minimum inlet pressure: 20 psi. Outlet pressure switch: 80-100 psi. 115V. Standard water boosters have a 1/3 HP motor, 100 GPH brass rotary vane pump and single ball check valve. Economy water boosters have a 100 GPH Aquatec motor and pump combination. Standard model Number Model Tank Inlet/Outlet Additional Information 162173 Standard 4 gallon 3/8" / 1/2" 168173 Standard 4 gallon 3/8" / 1/2" Low lead brass 162172 Standard 4 gallon 3/8" / 1/2" CC 168172 Standard 4 gallon 3/8" / 1/2" Low lead brass, CC 162171 Standard 2 gallon 3/8" / 1/2" 162171 Standard 2 gallon 3/8" / 1/2" Low lead brass 162170 Standard 2 gallon 3/8" / 1/2" CC 168170 Standard 2 gallon 3/8" / 1/2" Low lead brass, CC 1631723/8 Economy 2 gallon 3/8" 1631721/2 Economy 2 gallon 1/2" 1631743/8 Economy 4 gallon 3/8" 1631741/2 Economy 4 gallon 1/2" Economy model McCann s Water Booster s and Accessories Number Description 161473 Pressure switch and cord assembly for all McCann s boosters 111A100F11AA250 Rotary vane pump for 162171 or 162172 4406 Motor for 162171 or 162172 160166 Aquatec motor for 163172, 163173 or 163174 4406 Continuing product improvements may necessitate E-9
SHURflo Electric Water Booster Systems All booster systems include a mountable base, 30 psi water regulator and pump cord. The Mini has a plastic accumulator tank. The Medium and Maxi booster systems have a stainless steel tank. 115V. Mini Medium Maxi Number Description GPM Tank PSI Water Inlet/Outlet 804001 Mini boost system w mounting board 21 oz. 60 psi 3/8" metal barb 804002 Mini boost system w mounting board 21 oz. 90 psi 3/8" metal barb 804023 Medium E boost system w side mount, quick disconnect pump ports, 1.6 2 gal 90 psi 3/8" metal barb replaceable tank bladder 804023SV Medium E boost system w side mount, quick disconnect pump ports, 1.6 2 gal 90 psi 3/8" metal barb replaceable tank bladder, SHURlock shut-off ball valve 804037 Maxi boost system, 3/8" inlet/outlet 1.6 6 gal 90 psi 3/8" metal barb 804026 Maxi boost system, 1/2" inlet/outlet 1.6 6 gal 90 psi 1/2" metal barb SHURflo Electric Water Pumps Positive displacement 3 chamber diaphragm water delivery pumps are self-priming, and can run dry without damage. Pumps include ground wires and baseplate. 115V. 8025 Series 2088 Series 8005 Series Number Description GPM PSI Water Inlet/Outlet 2088594154 Transfer pump 3 45 1/2" MPT 8005733155 Delivery pump 1.4 60 1/2" MPT 8025213236 Standard water boost pump 1.4 60 3/8" FPT 8025933289 Standard water boost pump 1.4 90 3/8" FPT 8025933399 Replacement pump for water boosters: 804023, 804037, 804026 1.6 90 9405300 High flow/high pressure water boost/carbonation pump with two 3 chamber diaphragms 3.8 150 3/8" barb SHURflo Accumulator Tanks Number Description Water Inlet/Outlet 181201 21 oz. accumulator tank, metal mounting bracket 1/2" FPT 181400 21 oz. accumulator tank, gas pump QD clip ports 14045 2 gallon stainless steel tank, 1/2" or 3/4" FPT 181201 E-10 Continuing product improvements may necessitate
Water Booster Filter Combo Systems Filtered water improves the flavor of soft drinks, increases carbonation, and extends the life of equipment. Boosted water ensures consistent water pressure for consistent brix ratio, maximum flow rate and efficiency. Combining the two systems into one conserves valuable space. SHURflo s LVPO (Low Volume per Outlet) water boost filtration system is a complete turn-key solution which provides perfect ingredient water to low volume fountain dispensers and ice machines. The LVPO filtration system features: SHURflo 90 psi, 115 VAC, 8000 Series corded booster pump 2 gallon stainless steel water accumulator tank LVPO F-1 Big Boy 5 micron carbon block inline filter for particulate, chlorine, taste and odor reduction Filter can be mounted in any orientation, improving serviceability Colored coded inlet & outlet filter ports & valves for easy identification of water flow Quick connect 3/8" barb inlet/outlet ports Low pressure drop (less than 8 psi at 3.0 gpm) 50 psi pre-charge recommended for most beverage applications WB2LVPO01 is designed for single fountain dispensers that serve less than 500 gals. of syrup per year. Service life of filter: 6,000 gal. @ 3.0 GPM. SHURlock Fittings Double O-ring QD ball valve fittings (1/2" FPT straight & elbow available) 3/8" barb WB2LVPO02 has two filters; one that pressurizes and filters the water to a single dispenser that serves less than 500 gals. of syrup per year, and one that provides nonboosted treated water to the ice-maker. LVPO-F-1 (fountain filter) reduces particulates, chlorine, bad taste and odors. Service life: 6,000 gal. @ 3.0 GPM. LVPO-F-2 (ice filter) reduces particulates and inhibits lime scale build-up. Service life depends on the water conditions. Number WB2LVPO01 WB2LVPO02 Description Water boost/filter combo system for fountain dispenser, single filter cartridge Water boost/filter combo system for fountain dispenser and ice machine, dual filter cartridges 9489700 SHURlock kit: 1/2" FPT quick connect swivel ball valve, (2) 3/8" barb x 1/2" MPT 9489700 Continuing product improvements may necessitate E-11
Selecto Water Booster Filter Combo Systems Selecto SMF filters remove 99% of all contaminants, don t require a pre-filter for sediment removal, and provide high flow rates (up to 100 GPH/1.7 GPM) with nearly zero pressure drop. NSF std. 42 & 53. All SMF filters remove chloramine (chlorine + 20% ammonia used in many municipalities to slow the dissipation of chlorine). Chloramine has a strong odor, deteriorates O-rings, and causes stainless steel to pit, rust and turn gray. Low draw systems have a 2 gallon tank, high draw systems have a 4 gallon tank. Filters with -5 in the description have ScaleOUT (scale inhibitor) for ice machines. Operating pressure: 80-100 psi. Operating temperature: 40-100 F. Inlet and outlets: 3/8" barbs. Water analysis, site survey, selection of water appliances, service, maintenance and training are available. QC350 Low Draw QC500 Low Draw QC500/ScaleOUT Low Draw SMF IC600 Low Draw SMF IC600-5 Low Draw SMF IC614-5 Low Draw SMF IC620 Low Draw SMF IC620-5 Low Draw SMF IC620-5 High Draw Number Description Chlorine Chloramine Scale Tank Replacement Cartridge(s) 660350 QC350 Low Draw 8,000 gals. 4,000 gals. N/A 2 gals. QC3502 660500 QC500 Low Draw 11,000 gals. 6,000 gals. N/A 2 gals. QC5002 660500S QC500/ScaleOUT Low Draw 11,000 gals. 6,000 gals. 30,000 gals. 2 gals. 1090500S 660600LFM SMF IC600 Low Draw 50,000 gals. 7,000 gals. N/A 2 gals. 108010 666105LFM SMF IC600-5 Low Draw 50,000 gals. 7,000 gals. 75,000 gals. 2 gals. 108015S 666145LFM SMF IC614-5 Low Draw 70,000 gals. 15,000 gals. 75,000 gals. 2 gals. 108016S 660620LFM SMF IC620 Low Draw 100,000 gals. 30,000 gals. N/A 2 gals. 108020 660625LFM SMF IC620-5 Low Draw 100,000 gals. 30,000 gals. 75,000 gals. 2 gals. 108025S 660625HFM SMF IC620-5 High Draw 100,000 gals. 30,000 gals. 75,000 gals. 4 gals. 108025S E-12 Continuing product improvements may necessitate
3M Water Filtration Products for Multi-Equipment Applications The High Flow Series can meet the filtration needs of an entire foodservice establishment or address specific applications one at a time. A one-cartridge High Flow system with Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media delivers recipe quality water of up to 5 gallons per minute, lasts 6 months, and accomplishes what was previously the job of a three- or four-cartridge system. The High Flow Series provides unprecedented cyst and bacteria reduction, sediment holding, chlorine taste and odor reduction and scale inhibition. Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media provides nearly 6 times the filtration surface area, and reduction of up to 99.99% of common water-borne heterotrophic bacteria as tested by 3M Purification Inc., as well as Cryptosporidium and Giardia cysts. No activation steps are required, and for most water, no pre-filter is needed. Change-outs are fast and easy with the Sanitary Quick Change (SQC) encapsulated cartridge design. Most cartridge materials are NSF Std. 42 and/or CRF-21 compliant and certified by NSF to Std. 53 for cyst reduction. Dual Port (DP) and Dual Flow (DF) Systems for Multiple Applications Two separate streams exit the manifold. Both streams have reduced sediment and chlorine taste and odor. One stream has added scale inhibition media from a dedicated cartridge to help reduce the ability of calcium and magnesium to adhere as hard scale on the evaporator plates of an ice machine and/or the heating coils of a coffee brewer. The second stream supplies cold beverage dispensers and includes no added scale inhibitor. DP190 DP290 DP390 Model Number Gallon GPM Flow Rate Micron Rating Fountain/Cold Cup Coffee/Tea/Hot Cup Espresso/Cappacino Ice Machine Case Qty. Replacement Cartridge Reduces DP190 5624301 54,000 5.2 X X X 1 5613801 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 DP290 5624201 108,000 10.2 X X X 1 5613802 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 DP390 5624102 162,000 15.2 X X X 1 5613803 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 DF290-CL* 5623601 25,000 2.7 /5.2 X X 1 5613807 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chloramine, chlorine taste & odor, scale 3 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory *Beverage flow rate is 2.66 GPM, ice machine flow rate is 5 GPM. Continuing product improvements may necessitate E-13
3M Water Filtration Products for Cold Beverages Cold beverages are often the most profitable part of convenience stores, restaurants and quick-service operations. For these high-volume cold beverage applications, High Flow filters deliver enough Recipe Quality Water to make more than 432,000 soft drinks (16 oz. soft drinks in 22 oz. cups) with a single cartridge. High Flow catridge filters deliver the improved performance of Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media. A single High Flow cartridge system replaces a three- or four-cartridge manifold system, lowering capital and operating costs. All systems on this page deliver sediment and chlorine taste and odor reduction. BEV130 (std. 42 & 53) and BEV135 (std. 42) contain media wrapped carbon-block only. BEV140, BEV160 and BEV190 systems include Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria 2 reduction, and are NSF std. 42 and 53. BEV135, BEV145, BEV165 and BEV195 systems are designed for high turbidity water, but not cyst or bacteria reduction, and are std. 42 only. All have NSF and/or FDA CFR-21 compliant materials. BEV130 BEV135 BEV160 BEV165 BEV190 BEV195 Number Gallon GPM Flow Rate Micron Rating Fountain/Cold Cup Model Reduces BEV130 5616101 14,000 1.7.5 X 4 5615105 Cyst 1, sediment 3, chlorine taste & odor BEV135 5616102 12,600 1.7 1 X 4 5615205 Sediment 3, chlorine taste & odor Case Qty. Replacement Cartridge BEV140 5616201 25,000 2.1.2 X 2 5613303 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor BEV145 5616202 25,000 2.1 3 X 2 5613307 Sediment 3, chlorine taste & odor BEV160 5616301 35,000 3.3.2 X 1 5613403 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor BEV165 5616302 35,000 3.3 3 X 1 5613407 Sediment 3, chlorine taste & odor BEV190 5616401 54,000 5.2 X 1 5613503 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor BEV195 5616402 54,000 5 3 X 1 5613507 Sediment 3, chlorine taste & odor 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory E-14 Continuing product improvements may necessitate
3M Water Filtration Products for Ice Machines Scale build-up on evaporator plates can significantly increase maintenance costs. 3M Water Filtration Products for ice machines provide built-in scale inhibition as well as chlorine and sediment reduction, which reduce service calls and downtime, yield consistent product, and increase customer satisfaction. ICE120-S (std. 42 & 53) and ICE125-S (std. 42) contain carbonblock media only. ICE140-S, ICE160-S, ICE190-S and ICE260-S include Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria 2 reduction, and are NSF std. 42 and 53. For higher turbidity waters, the media in ICE145-S, ICE165-S, ICE195-S and ICE265-S systems are specifically designed to provide cartridge and system life, but not cyst or bacteria reduction, and are std. 42 only. All have NSF and/or FDA CFR-21 compliant materials. ICE265-S ICE190-S ICE120-S ICE140-S Model Number Gallon GPM Flow Rate Micron Rating HF Cubers Lbs. To LF Cubers Lbs. To Flakers Lbs. To Continuing product improvements may necessitate E-15 Case Qty. Replacement Cartridges ICE120-S 5616003 9,000 1.5.5 200 750 1200 6 HF20S 5615103 ICE125-S 5616004 10,000 1.5 1 200 750 1200 6 HF25S 5615203 ICE140-S 5616203 25,000 2.1.2 600 1000 1800 2 HF40S 5613305 ICE145-S 5616204 25,000 2.1 3 600 1000 1800 2 HF45S 5613309 ICE160-S 5616303 35,000 3.3.2 1000 1450 2400 1 HF60S 5613405 ICE165-S 5616304 35,000 3.3 3 1000 1450 2400 1 HF65S 5613409 ICE190-S 5616403 54,000 5.2 >1000 >1450 >2400 1 HF90S 5613505 ICE195-S 5616404 54,000 5 3 >1000 >1450 >2400 1 HF95S 5613509 ICE260-S 5624503 70,000 6.7.2 2400 3000 4800 1 (2) HF60S 5613405 ICE265-S 5624504 70,000 6.7 3 2400 3000 4800 1 (2) HF65S 5613409 Reduces Cyst 1, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory
3M Water Filtration Products for Hot Beverages High Flow Series products for hot beverage applications reduce excess sediment and chlorine that cause bitter taste and clog spray heads. If not filtered, these elements can wreak havoc on your equipment and lead to expensive repair and replacement costs. When scale is an issue, High Flow BREW systems add scale inhibitor to prevent calcium and magnesium build-up that can significantly decrease efficiency and increase maintenance costs. ESP and ScaleGARD Pro (SGP) systems reduce calcium and magnesium ions by ion exchange (water softening) for crystal clear iced tea and excellent bean extraction for espresso and espresso-based beverages. ESP and SGP systems do not need a drain, electrical connection or salt regeneration. All have NSF and/or FDA CFR-21 compliant materials. BREW 120 BREW 130 ESP 124 SGP 165 Model Number Gallon GPM Flow Rate Micron Rating Coffee/Hot Cup Espresso/Capp./Tea Case Qty. Replacement Cartridge(s) BREW105-MS 6213801 1,500.75 1 X 8 HF05MS 5609327 BREW110-MS 6213803 3,500 1.5 X 8 HF10MS 5609329 BREW115-MS 6213807 3,500 1 5 X 8 HF15MS 5609331 BREW120-MS 5616001 9,000 1.5.5 X 6 HF20MS 5615109 BREW125-MS 5616002 10,000 1.5 1 X 6 HF25MS 5615209 BREW130-MS 5616103 14,000 1.7.5 X 4 HF30MS 5615111 BREW135-MS 5616104 12,600 1.7 1 X 4 HF35MS 5615211 Reduces Sediment 2, chlorine taste & odor, scale 2 Cyst 1, sediment 2, chlorine taste & odor, scale 2 Sediment 2, chlorine taste & odor, scale 2 Cyst 1, sediment 2, chlorine taste & odor, scale 2 Sediment 2, chlorine taste & odor, scale 2 Cyst 1, sediment 2, chlorine taste & odor, scale 2 Sediment 2, chlorine taste & odor, scale 2 ESP114-T* 5617609 700 gr..5 N/A X 6 5610909 Hardness (softens), chlorine taste & odor ESP124-T* 5617610 1,100 gr..5 N/A X 4 5610907 Hardness (softens), chlorine taste & odor SGP124BN-T* 5617603 422.6.5 N/A X 4 5610901 Hard scale 2, chlorine taste & odor SGP165BN-T* 5617601 719 1 N/A X 1 5615601 Hard scale 2, chlorine taste & odor SGP195BN-T* 5617602 1200 1 N/A X 1 5615001 Hard scale 2, chlorine taste & odor SGP-124B* 5608902 422.6.5 N/A X X 4 5609103 Hard scale 2, chlorine taste & odor 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested and verified by Manufacturer s Laboratory *Systems not NSF listed E-16 Continuing product improvements may necessitate
3M Water Filtration Products for Hot Beverages - Reverse Osmosis NEW! For optimum flavor it is recommended that filtered water contain 100-200 ppm of Total Dissolved Solids (TDS) for coffee and about 50 ppm for espresso. Designed for water conditions with high TDS and/or hardness, the TFS450 reverse osmosis (RO) water filtration system is ideal. RO is the tightest of all filtration processes, removing about 90% of all contaminants and providing the greatest equipment protection. The TFS450 has a blending feature that allows you to blend back just the right amount of TDS (from 10-50% of incoming feed water) into the water to satisfy both needs; equipment protection and customer satisfaction. With conventional RO systems the waste water can be 2-4 times the volume of the filtered water. For the production of 100 gallons of filtered water the TFS450 conserves up to 250 gallons of water per day - over 90,000 gallons per year - than conventional RO systems. Features: Makes 300 gal/day without blending*, and up to 600 gal/ day of blended water Blending valve (with lock) adjusts the desired amount of TDS, and online meter monitors product water TDS level Keeps running during high demand periods and power outages with automatic non-electric bypass All product water (including bypass) is pre- and postfiltered Change-outs are fast and easy with Sanitary Quick Change (SQC) disposable cartridges Compact, uses very little space, and is easy to install Optional pumping module is available for low inlet water pressure areas The TFS450 requires an external storage tank. TFS450 Model Number Gallon TFS450RO 5623901 300 gpd without blending/ 600 gpd with blending Micron Rating Coffee/Hot Cup Espresso/Capp./Tea Case Qty. Replacement Cartridge(s) Reduces.0005 X X 1 5624802 Cysts 1, sediment 2, chlorine taste & odor, TDS 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested and verified by Manufacturer s Laboratory *at 77 F and 70 psi. Continuing product improvements may necessitate E-17
3M Replacement Cartridges for 3M Water Filtration Systems Sorted by Number Number Gallon GPM Flow Rate Micron Rating Case Qty. Model Reduces 5609327 HF05-MS 1,500.75 1 8 Sediment 3, chlorine taste and odor, scale 3 5609329 HF10-MS 3,500 1.5 8 Cyst 1, sediment 3, chlorine taste and odor, scale 3 5609331 HF15-MS 3,500 1 5 8 Sediment 3, chlorine taste and odor, scale 3 5610901 P124BN* 423@ 10 gr..5 N/A 4 Hardness, chlorine taste and odor 5610907 PS124* 1,100 gr..5 N/A 4 Hardness, chlorine taste and odor 5610909 PS114* 700 gr..5 N/A 6 Hardness (softens), chlorine taste and odor 5613303 HF40 25,000 2.1.5 2 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor 5613305 HF40-S 25,000 2.1.2 2 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale 3 5613307 HF45 25,000 2.1 1 2 Sediment 3, chlorine taste and odor 5613309 HF45-S 25,000 2.1 3 2 Sediment 3, chlorine taste and odor, scale 3 5613403 HF60 35,000 3.3.2 1 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor 5613405 (2) HF60-S 70,000 6.7.2 1 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale 3 5613407 HF65 35,000 3.3 3 1 Sediment 3, chlorine taste and odor 5613409 (2) HF65-S 70,000 6.7 3 1 Sediment 3, chlorine, taste and odor, scale 3 5613503 HF90 54,000 5.2 1 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor 5613505 HF90-S 54,000 5.2 1 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale 3 5613507 HF95 54,000 5 3 1 Sediment 3, chlorine taste and odor 5613509 HF95-S 54,000 5 3 1 Sediment 3, chlorine taste and odor, scale 5613801 DP190-CARTPAK 54,000 5.2 1 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale 3 5613802 DP290-CARTPAK 108,000 10.2 1 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale 3 5613803 DP390-CARTPAK 162,000 15.2 1 Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale 3 5613807 DF290CL-CART- 25,000 2.7/5.2 1 Cyst 1, bacteria 2, sediment 3, chloramine, chlorine taste and odor, scale 3 PAK 5615001 P195BN* 1200@ 9 gr. 1 N/A 1 Hardness, chlorine taste and odor 5615103 HF20-S 9,000 1.5.5 6 Cyst 1, sediment 3, chlorine taste and odor, scale 3 5615105 HF30 14,000 1.7.5 4 Cyst 1, sediment 3, chlorine taste and odor 5615109 HF20-MS 9,000 1.5.5 6 Cyst 1, sediment 3, chlorine taste and odor, scale 3 5615111 HF30-MS 14,000 1.7.5 4 Cyst 1, sediment 3, chlorine taste and odor, scale 3 5615203 HF25-S 10,000 1.5 1 6 Sediment 3, chlorine taste and odor, scale 3 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory *Systems not NSF listed E-18 Continuing product improvements may necessitate
3M Replacement Cartridges for 3M Water Filtration Systems Sorted by Number Number Gallon GPM Flow Rate Model Reduces 5615205 HF35 12,600 1.7 1 4 Sediment 3, chlorine taste and odor 5615209 HF25-MS 10,000 1.5 1 6 Sediment 3, chlorine taste and odor, scale 3 5615211 HF35-MS 12,600 1.7 1 4 Sediment 3, chlorine taste and odor, scale 3 5615601 P165BN* 719@ 9 gpg 1 N/A 1 Hardness, chlorine taste and odor 5572101 CFS9110 N/A 1.5 5 4 Sediment 3 5589203 CFS9112 10,000 1.5 1 12 Sediment 3, chlorine taste and odor 5601201 CFS9812X 9,000 1.5.5 12 Cyst 1, sediment 3, chlorine taste and odor 5589003 CFS9720 4,800 1.5 5 12 Sediment 3, chlorine taste and odor 5572103 CFS9110S N/A 1.5 5 4 Sediment 3, scale 3 5589201 CFS9112S 10,000 1.5 1 12 Sediment 3, chlorine taste and odor, scale 3 5601203 CFS9812XS 9,000 1.5.5 12 Cyst 1, sediment 3, chlorine taste and odor, scale 3 5589101 CFS9710S 2,400 1 5 12 Sediment 3, scale 3 5589001 CFS9720S 4,800 1.5 5 12 Sediment 3, chlorine taste and odor, scale 3 5593701 CFS9005IMF N/A N/A N/A 12 Scale 3 5589213 CFS9112EL 12,600 1.67 1 4 Sediment 3, chlorine taste and odor 5601205 CFS9812ELX 14,000 1.67.5 4 Cyst 1, sediment 3, chlorine taste and odor 5589005 CFS9720EL 5,500 1.67 5 4 Sediment 3, chlorine taste and odor 5589215 CFS9112ELS 12,600 1.67 1 4 Sediment 3, chlorine taste and odor, scale 3 5601207 CFS9812ELXS 14,000 1.67.5 4 Cyst 1, sediment 3, chlorine taste and odor, scale 3 5589007 CFS9720ELS 5,500 1.67 5 4 Sediment 3, chlorine taste and odor, scale 3 5572201* SWC9135 1,350 gr..5 N/A 4 Scale 3 (softens water) 5572203* SWC9135C 1,100 gr..5 5 4 Chlorine taste and odor, scale 3 (softens water) Micron Rating 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory *Systems not NSF listed Case Qty. 3M Replacement Filters NEW! NEW 9000 Series cartridges fit all Everpure heads, both old and new style. Continuing product improvements may necessitate E-19
Selecto Water Filtration Systems Selecto s SMF filters last up to 10 times longer than traditional carbon filters. Modular units are simple to install and service, and adaptable to changing water conditions change. All systems (except some inline filters) come with mounting brackets. Fountain systems have a pressure gauge. 100% performance guarantee. NSF 42 & 53. Selecto s hollow carbon filter Traditional carbon block filter Selecto can customize a filtration system to meet your requirements. Call customer service for details. IL35 QC350 QC500 SMF IC600 SMF IC614 SMF IC620 SMF IC620S SMF IC6142 SMF IC6202 SMF IC6203 SMF Espresso 7500 SMF Espresso 12000 SMF CoffeePRO SMF IC600S ScaleOUT-W E-20 Continuing product improvements may necessitate
Selecto Water Filtration Systems Gallon GPM Flow Rate Fountain Juice Coffee Tea* Espresso/Capp. Ice Machine Replacement Cartridge(s) Model Number Reduces/Eliminates IL35 0110/35 3,000 2 X X X X 0110/35 Chlorine, sediment, bad taste, odor IL35B 0110/35B 3,000 1 X X X 0199/35B Chlorine, sediment, bad taste, odor IL35S 0110/35S 3,000 2 X X X 0110/35S Chlorine, sediment, bad taste, odor, scale IL35BS 0110/35BS 2,500 1 X X X 0199/35BS Chlorine, sediment, bad taste, odor, scale QC350 QC3503 8,000 2.2 X X X X QC3502 Chlorine, chloramine, sediment, bad taste, odor QC350S QC350S 8,000 2.2 X X X X QC3502S Chlorine, chloramine, sediment, bad taste, odor, scale QC350F QC350F 8,000 2.2 X QC350-2 Chlorine, chloramine, sediment, bad taste, odor, scale QC500 QC5003 11,000 2.5 X X X X QC5002 Chlorine, chloramine, sediment, bad taste, odor QC500S QC500S 11,000 2.5 X X X X QC5002S Chlorine, chloramine, sediment, bad taste, odor, scale QC500F QC500F 11,000 2.5 X QC500-2 Chlorine, chloramine, sediment, bad taste, odor, scale QC500 Combo 60-0500S 11,000 2.5 X X 1090500S Chlorine, chloramine, sediment, bad taste, odor, scale SMF Espresso 7500 SMF Espresso 12000 SMF CoffeePRO 821600 7,500 1 X X X 108600 Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale 821620 12,000 2 X X X 108620 Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale 806100CP 15,000 5 X X X 108010CP Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale ScaleOUT 05260W 40,000 5 X X X X 101260 Scale SMF IC600 806100 50,000 2.5 X X X X X 108010 Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor SMF IC614 806140 70,000 3.7 X X X X X 108014 Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor SMF IC620 806200 100,000 5 X X X X X 108020 Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor SMF IC600S 801600S 50,000 5 X X X X X X 108015S Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IC620S 806200S 100,000 5 X X X X X X 108020S Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IC6142 806142 140,000 7.4 X X X X X X 1080142 Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IC6202 80-6202 200,000 10 X X X X X 1080202 Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor SMF IC6203 806203 300,000 15 X X X X X 1080203 Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor * numbers ending in S provide scale inhibition, which in some water conditions may cause tea to become cloudy. Continuing product improvements may necessitate E-21
Selecto Water Filtration Systems SMF IcePRO SMF IM600 SMF IM614 SlimeGUARD Spray SlimeGUARD Stick Gallon GPM Flow Rate Ice Machine Replacement Cartridge(s) Model Number Reduces/Eliminates SMF IcePRO 806100IP 15,000 5 X 108010IP Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IM600 806100S 75,000 7 X 108010S Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IM614 80614S 150,000 7 X 108014S Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SlimeGUARD Spary 40003 N/A N/A X N/A Bacteria, mold, algae and fungus up to 3 months, ice makers up to 2400 lbs. SlimeGUARD Stick 40002 N/A N/A X N/A Bacteria, mold, algae and fungus up to 3 months, ice makers up to 2400 lbs. SHURflo Inline Filters Number GPM Port Fitting Reduces/Eliminates SF210TO 2 1/4" plastic FPT taste, odor SF210TOS 2 1/4" plastic FPT taste, odor, sediment SF210SED 2 1/4" plastic FPT sediment SF210TOHQD 2 1/4" brass quick disconnect taste, odor SF210TOSHQD 2 1/4" brass quick disconnect taste, odor, sediment SF210SEDHQD 2 1/4" brass quick disconnect sediment SF210TOPQD 2 1/4" plastic quick disconnect taste, odor SF210TOSPQD 2 1/4" plastic quick disconnect taste, odor, sediment SF210SEDPQD 2 1/4" plastic quick disconnect sediment SF215TOCAT 2.5 1/4" plastic FPT SF215CATPQD 2.5 1/4" plastic quick disconnect Female plastic quick disconnects can be found in the Installation Products, fittings section. E-22 Continuing product improvements may necessitate
SHURflo Water Filtration Systems Number Single Standard 10" Filter System, 3/8" MPT threads SF410010 With ball valve & gauge, no filters SF410020 No fittings, no filters, single packed SF410021 No fittings, no filters, bulk packed (12 to case) SF412010 With ball valve & gauge, Granular Activated Carbon (GAC) element SF414010 With ball valve & gauge, Granular Activated Carbon (GAC) / Phosphate Element Dual Standard 10" Filter Systems, 3/8" MPT threads SF510010 With ball valve & gauge, no filters SF510020 No fittings, no filters SF511110 With ball valve & gauge, 5 micron sediment/gac element SF511310 With ball valve & gauge, 5 micron sediment/gac/phosphate element SF414010 With ball valve & gauge, Granular Activated Carbon (GAC) / Phosphate Element Dual Standard 10" UV Filter Systems, 3/8" MPT threads SF520010 US System with ball valve & gauge, mechanical ballast, no filters SF520020 US System, no fittings, mechanical ballast, no filters SF521110 US System with ball valve & gauge, mech. ballast, 5 mic sed/gac element Dual Great White 10" x 20" Filter Systems, 3/4" MPT threads SF60010 With ball valve & gauge, no filters SF60020 No fittings, no filters SF600TOCL With ball valve & gauge, 5 micron sediment/gac element Dual Great White 10" Filter Systems, 3/4" MPT threads SF50010 With ball valve & gauge, no filters SF50020 No fittings, no filters SF500TOCL With ball valve & gauge, 5 micron sediment/gac element Dual Great White 10" UV Filter Systems, 3/4" MPT threads SF530010 US System with ball valve & gauge, mechanical ballast, no filters SF530020 US System, no fittings, mechanical ballast, no filters Dual Great White 20" Filter Systems, 3/4" MPT threads SF70010 With ball valve & gauge, no filters SF70020 No fittings, no filters Accessory Description 1505610 UV light, 2.0 GPM, 8 watts, 2 pin 1505611 UV light, 1.0 GPM, 6 watts, 2 pin 1505700 UV light ballast, 2 pin 1505800 Clip set (2) for UV light and inline filters 1504800 Wrench for standard series sumps 1504700 Wrench for Great White Series 10" sumps 1504900 Wrench for Great White Series 20" sumps UV light 1505800 Single Standard 10" 1505700 Dual Standard 10" Dual Standard 10" UV Dual Great White 10" & 20" Dual Great White 10" Wrenches Continuing product improvements may necessitate E-23
SHURflo Replacement Filters Number Standard 10" Replacement Filters 1502812 Standard 10" 0.5 micron modified molded carbon block FD 1505200 Standard 10" 5 micron spun bonded polypropylene sediment cartridge 1505300 Standard 10" 20 micron water washed coconut shell granular activated carbon (GAC) element 1505400 Standard 10" 5 micron GAC w food grade hexametaphosphate 1505420 Standard 10" phosphate crystal cartridge 1505430 Standard 10" cation softening resin 1505500 Standard 10" 20 micron spun bonded polypropylene sediment cartridge 1505620 Standard 10" 4-8 micron modified molded block FD 1505610 Standard 10" 4-8 micron modified molded block FD with siliphos softening 1505203 Standard 20" 5 micron spun bonded polypropylene sediment cartridge 1505503 Standard 20" 20 micron spun bonded polypropylene sediment cartridge 1506200 Standard 20" 10 micron modified molded carbon block 1505300 Standard 20" 0.5 micron modified molded carbon block 1503900 Great White 10" 5 micron modified carbon block - FD 1503910 Great White 10" 5 micron modified carbon block - FD with siliphos 1504000 Great White 10" 0.5 micron carbon briquette 1505201 Great White 10" 1 micron nom dual gradient density SED element - spun poly 1505301 Great White 10" 5 micron granular activated carbon/sed element 1505401 Great White 10" 5 micron SED element - pleated polypropylene 1504100 Great White 20" 0.5 micron carbon briquette 1505202 Great White 20" 1 micron nom dual gradient density SED element - spun poly 1505302 Great White 20" 5 micron granular activated carbon/sed element 1505402 Great White 20" 5 micron SED element pleated polypropylene 9475100 LVPO-F1 starter kit: 5 micron carbon filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass 9447900 LVPO-F2 starter kit: 5 micron sediment & phosphate filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass 9475101 LVPO-F3 starter kit: 5 micron carbon & phosphate filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass 9475102 LVPO-F4 starter kit: inline resin filter, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass 9439900 LVPO-F1, 5 micron carbon filter NSF 42, 3 GPM, 6000 gal life 9447000 LVPO-F2, 5 micron sediment & phosphate filter NSF 42, 3 GPM, life depends on water conditions 9447001 LVPO-F3, 5 micron carbon & phosphate filter NSF 42, 3 GPM, 6000 gal life 9447002 LVPO-F4, inline resin filter,.5 GPM, 4400 grains or 500 gal @ 150 ppm 9472900 PLF-1 inline 5 micron carbon filter NSF 42, 2 GPM, 5000 gal life 1505620 1503900 LVPO starter kit LVPO-F1 LVPO-F2 LVPO-F3 LVPO-F4 E-24 Continuing product improvements may necessitate
SHURflo Accessories and Fittings Number Description 9447500 LVPO filter QD-bypass 9447300 LVPO filter brackets for slide track/wall mount, 1 pair 9447400 LVPO filter to filter brackets, 1 pair 9447200 LVPO filter brackets for tank mount, 1 pair 9447100 Quick connect 3/8" barb ball valve set: gray handle for inlet, blue handle for outlet 9447101 Quick connect 1/2" FPT with SS rings ball 90 valve set: gray handle for inlet, blue handle for outlet 183130SS 30 psi water pressure reducer valve, 3/8" SS barb inlet/outlet 183150SS 50 psi water pressure reducer valve, 3/8" SS barb inlet/outlet 183165SS 65 psi water pressure reducer valve, 3/8" SS barb inlet/outlet 183180SS 80 psi water pressure reducer valve, 3/8" SS barb inlet/outlet 9416500 65 psi water pressure reducer valve w pressure gauge, 3/8" barb inlet/outlet 17006029 Water strainer, 50 mesh SS screen, EPDM O-ring, 1/2" barb inlet, 1/2" FPST outlet.* 17006104 Water strainer, 50 mesh SS screen, Buna O-ring, 1/2" barb inlet, 1/2" FPST outlet.* 17006105 Water strainer, 50 mesh SS screen, Viton O-ring 1/2" barb inlet, 1/2" FPST outlet.* 17006109 Water strainer, 50 mesh SS screen, EPDM O-ring 1/2" barb inlet, 1/2" FPST outlet.* 8433134 Tank pressure switch, 25 psi on/40 psi off, NPT ports 9409000 Tank pressure switch, 25 psi on/40 psi off, FPT ports, 2' wire harness 9409001 Tank pressure switch, 25 psi on/40 psi off, push fit connectors, 2' wire harness 9409002 Tank pressure switch, 25 psi on/40 psi off, 3/8" push fit connectors, 2' wire harness 8433137 Low pressure switch, 3 psi on / 8 psi off, FPT ports 9408001 Low pressure switch, 3 psi on / 8 psi off, push fit connectors, 2' wire harness 800700 3/8" MPT x 1/2" straight barb, electric pump fitting, plastic 800500 3/8" MPT x 3/8" straight barb, electric pump fitting, plastic 800800 3/8" MPT x 1/2" elbow barb, electric pump fitting, plastic 800600 3/8" MPT x 3/8" elbow barb, electric pump fitting, plastic 807000 1/2" swivel nut x 1/2" straight barb, electric pump fitting, plastic 807100 1/2" swivel nut x 3/8" straight barb, electric pump fitting, plastic 807200 1/2" swivel nut x 1/4" straight barb, electric pump fitting, plastic 803400 1/2" swivel nut x 1/2" elbow barb, electric pump fitting, plastic 806000 1/2" swivel nut x 3/8" elbow barb, electric pump fitting, plastic 806900 1/2" swivel nut x 1/4" elbow barb, electric pump fitting, plastic 814500 3/8" MPT x 1/2" MPT adapter, electric pump fitting, plastic *Use adapter 814501 for 8000 Series pumps with 3/8" FPT Quick connect 90 valve set Water pressure reducer valve Water strainers Tank pressure switch Continuing product improvements may necessitate E-25
SHURflo Accessories and Fittings Number Description 807001 Hex swivel straight, polypropylene 1/2" FPT x 1/2" barb 807101 Hex swivel straight, polypropylene 1/2" FPT x 3/8" barb 815401 Wingnut swivel straight, polypropylene 1/2" FPT x 5/8" barb 815601 Wingnut swivel straight, polypropylene 1/2" FPT x 3/4" barb 816101 Wingnut swivel straight, polypropylene 1/2" FPT x 1/2" barb 815501 Wingnut swivel elbow, polypropylene, 1/2" FPT x 5/8" barb 815801 Wingnut swivel elbow, polypropylene, 1/2" FPT x 1/2" barb 815901 Wingnut swivel elbow, polypropylene, 1/2" FPT x 3/8" barb 815701 Wingnut swivel elbow, polypropylene, 1/2" FPT x 3/4" barb 803400 Hex swivel elbow, polypropylene, 1/2" FPT x 1/2" barb 806000 Hex swivel elbow, polypropylene, 1/2" FPT x 3/8" barb 803500 Hex swivel elbow, polypropylene, 1/2" FPT x 1/2" MPT 820500 Adapter, nylon 1/2" FPT x 1/2" MPT 815001 Adapter, Nylon 1/2" FPT x 3/4" GSH (M) 826901 Adapter, Nylon 1/2" MPT x 3/4" barb 812600 Barb tee, polypropylene, 1/2" barb x 1/2" barb x 1/2" barb Hex swivel straight Wingnut swivel straight Wingnut swivel elbow Hex swivel elbow Adapter, FPT x MPT Adapter, FPT x GSH (M) Adapter, MPT x barb Barb tee E-26 Continuing product improvements may necessitate
Everpure Water Filtration Systems Everpure products can help you enjoy the taste without the waste of bottled water, and indirectly reduce waste by saving energy and prolonging the life of your equipment. Water analysis, site survey, selection of water appliances, service, maintenance and training are available. Everpure has over 200 models and model variations, and can customize a system to meet your needs. The most popular systems are shown here. All systems have a five year warranty, and cartridges have a one year limited warranty. NSF std. 42 & 53. QC71 Single-MC QC71 Twin-MC QC71 Triple-MC QC71 Quad-MC Coldrink 1-MC Coldrink 2-MC Coldrink 3-MC Dual HF Coldrink S-MC CB20-124E CB20-302E CB20-312E Insurice Single I2000 Insurice Twin I2000 Insurice Triple I4000 Insurice Quad I4000 E-Series 10" Prefilter E-Series 20" Prefilter SRX Scale Inhibitor Feeder IN-6 Inline Filter IN-10 Inline Filter Head and filter sold separately IN-12 Inline Filter EV933726 SRX QL2-OW200L QL2-OCS QL3-BH QC7I Single-MH Continuing product improvements may necessitate E-27
Everpure Water Filtration Systems Did you know as little as a 1/8" layer of scale can reduce the efficiency of a coffee machine by 50%, resulting in twice the amount of electricity consumed? Gallon GPM Flow Rate Fountain Model Number Reduces/Eliminates QC71 Single-MC 2 EV927501 9,000 1.7 X X (1) EV961256 Sediment, taste, odor, cyst QC71 Twin-MC 2 EV927502 18,000 3.3 X X (2) EV961256 Sediment, taste, odor, cyst QC71 Triple-MC 2 EV927503 27,000 5 X X (1) EV997042 Sediment, taste, odor, cyst QC71 Quad-MC 2 EV933711 36,000 6.7 X X (1) EV962828 Sediment, taste, odor, cyst Coffee Espresso/Capp. Ice Machine Drinking Water Combination Replacement Cartridge(s)/Kits QC71 Single-MH 2 EV927241 9,000 1 X (1) EV961301 Sediment, chlorine, taste, odor, cyst, scale (head only, filter sold separately) QC71 Twin-MH 2 EV927222 18,000 1 X (2) EV961321 Sediment, chlorine, taste, odor, cyst, scale (head only, filter sold separately) QC71 Single-ESO7 EV927241 5,300 gr..5 X (1) EV960725 Hardness QC71 Twin-ESO7 EV927222 10,600 gr. 1 X (2) EV960725 Hardness QC71 Triple-ESO7 EV927223 15,900 gr. 1.5 X (3) EV960725 Hardness Coldrink 1 MC 2 EV932801 9,000 1.7 X (1) EV953426 Sediment, taste, odor, cyst (1) EV961256 Coldrink 2 MC 2 EV932802 18,000 3.3 X (1) EV953426 Sediment, taste, odor, cyst (2) EV961256 Coldrink 3 MC 2 EV932803 27,000 5 X (1) EV953426 Sediment, taste, odor, cyst (3) EV961256 Dual High Flow EV933744 72,000 13.4 X (2) EV953426 Sediment, taste, odor, cyst Coldrink S-MC 2 (8) EV961256 Dual High Flow EV933722 96,000 13.4 X (2) EV953426 Sediment, taste, odor, cyst Coldrink M-XC 2 X (8) EV961256 CB20-124E EV910051 15,000 5 X X X X X (1) EV910502 Chloramine, chlorine, taste, odor, cyst CB20-302E EV910032 20,000 5 X X X X X (1) EV910521 Chloramine, chlorine, taste, odor, cyst CB20-312E EV910037 60,000 5 X X X X X (1) EV910534 Chloramine, chlorine, taste, odor, cyst Insurice Single I2000 2 EV932401 9,000 1.7 X (1) EV961222 Sediment, chlorine, taste, odor, cyst, scale Insurice Twin I2000 2 EV932402 18,000 3.3 X (2) EV961222 Sediment, chlorine, taste, odor, cyst, scale Insurice Triple I4000 2 EV932503 36,000 5 X (3) EV931232 Sediment, chlorine, taste, odor, cyst, scale Insurice Quad I4000 2 EV932504 48,000 6.7 X (4) EV931232 Sediment, chlorine, taste, odor, cyst, scale Insurice Single PFI2000 2 EV932421 9,000 1.7 X (1) EV953426 (1) EV961222 Insurice Twin PFI2000 2 EV932422 18,000 3.3 X (1) EV953426 (2) EV961222 Insurice Triple PFI4000 2 EV932523 36,000 5 X (1) EV953426 (3) EV961232 SRX Scale Inhibitor EV979845 Depends N/A X X (1) EV979902 Scale, deliming E-Series 10" Prefilter EV979580 Depends N/A X X X X X X (1) EV953412 Sediment E-Series 20" Prefilter EV979590 Depends N/A X X X X X X (1) EV953412 Sediment Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection E-28 Continuing product improvements may necessitate
Everpure Water Filtration Systems EV927224 Head and filters sold separately EV910003 EV933042 EV934720 EV934400 EV910094 EV910002 EV932805 EV934430 Gallon GPM Flow Rate Fountain Coffee Esp./Capp./Tea Ice Machine Drinking Water Combination Replacement Cartridge(s) Model Number Reduces/Eliminates MC 2 -SO EV927224 9,000 1.7 X (1) EV961256 Sediment, taste, odor, cyst, and softens (1) EV960704 2,000 grains SO-24 Espresso EV910094 4,500 2 X (1) DEV910545 Hardness (softens 4,500 grains) SO-20 Housing EV910003 1,500.75 X (1) DEV910542 Hardness (softens 1,500 grains) SO-10 Housing EV910002 750.5 X (1) DEV910541 Hardness (softens 750 grains) High Flow CSR Twin-MC 2 EV933042 18,000 3.3 X X X X X (1) EV953426 (2) EV961256 (1) EV979932 High Flow CSR Triple-MC 2 *optional low pressure alarm High Flow CSR Quad- MC 2 *optional low pressure alarm High Flow CSR Plus-XC 2 (with 5 gallon reserve surge tank) HSD 440P Automatic Self Flushing Prefilter (120V) EV932806, *with alarm: EV932805 EV943710, *with alarm: EV943711 EV944720, *with alarm: EV934721 27,000 5 X X X X X (1) EV953426 (3) EV961256 (1) EV979932 36,000 6.7 X X X X X (1) EV953426 (4) EV961256 (1) EV979932 48,000 6.7 X X X X X (1) EV953426 (4) EV961310 (1) EV979932 Sediment, taste, odor, cyst, scale Sediment, taste, odor, cyst, scale Sediment, taste, odor, cyst, scale Sediment, taste, odor, cyst, scale EV934400 N/A 10 X X X X X X (1) EV312536 Sediment, turbidity, bacteria, virus (.025 micron) QL2-OW200L EV927570 480.5 X (1) EV961901 Sediment, chlorine, taste, odor, lead, THMs, asbestos, cyst, scale QL2-OCS 2 EV927560 1,500.5 X (1) EV961801 Sediment, chlorine, taste, odor, cyst, scale QL3-BH 2 EV927200 3,000.5 X (1) EV961200 Sediment, chlorine, taste, odor, cyst, scale Continuing product improvements may necessitate E-29
Everpure Claris Water Filtration Systems for Coffee, Espresso and Brewed Iced Tea To achieve the Golden Cup Standards of the Specialty Coffee Association of America, it is recommended that filtered water contain 100-200 ppm of Total Dissolved Solids (TDS) for coffee and ~50 ppm for espresso for optimum flavor. Claris adjustable ion-selective filters enable you to tailor the carbonate hardness levels to deliver just the right amount of TDS for optimum coffee and espresso flavor while removing excessive and harmful hard water contaminants. Claris can be installed vertically or horizontally. The head features a built-in flush port, auto shut-off, adjustable by-pass, flow restrictor and backflow restrictor. The duo-blend by-pass technology has a 5-stage filtration process: Pre-filtration Carbonate hardness adjustment Fine filtration Highly efficient carbon block removes harmful contaminants and unpleasant odors and tastes Solid membrane filter removes particles down to 5 microns for equipment protection Heads and filters are sold separately. The CLARIS Flow Sensor monitors the filtrate volume to calculate and display the remaining filtration capacity in litres. When the filtration capacity or the maximum operation time has been reached the display unit indicates filter cartridge replacement. The programming and display unit shows: Residual capacity of installed filter cartridge Filtrate volume of the last five installed filter cartridges Operation time of the last five installed filter cartridges Total filtrate volume since Flow Sensor installation Claris Filter Family Gallon GPM Flow Rate Micron Rating Filter Number Reduces/Eliminates Claris Small EV433910 400.5 5 X X 1 Hardness, sediment, chlorine, taste, odor, scale Claris Medium EV433911 660.5 5 X X 1 Hardness, sediment, chlorine, taste, odor, scale Claris Large EV433912 1100 1 5 X X 1 Hardness, sediment, chlorine, taste, odor, scale Claris X-Large EV433913 1585 1 5 X X 1 Hardness, sediment, chlorine, taste, odor, scale Coffee Esp./Capp./Tea Case Qty. Number EV433921 EV433923 EV433925 EV433931 EV433940 Description Claris Head 3/8" BSP Claris Head 3/8" QCF Claris Head 1/4" QCF Claris Flowmeter Claris Test Kit Claris Head Claris Flowmeter EV433931 Claris Test Kit E-30 Continuing product improvements may necessitate
Everpure Costguard Water Filtration Systems DEV910010 DEV910012 DEV910020 DEV910022 DEV910023 DEV910050 Housing Number Filter Size Connection CGS-10 Single DEV910010 10" 3/8" FPT CGS-12 Dual DEV910012 10" 1/2" FPT CGS-20 Single DEV910020 20" 3/8" FPT CGS-22 Dual DEV910022 20" 1/2" FPT CGS-23 Parallel DEV910023 20" 3/8" FPT CGS-55 Single DEV910050 20" 1/2" FPT Costguard value priced filtration systems are designed for rigorous applications. Housings feature inlet/outlet shut-off valves, gauges, mounting bracket and hardware. Costguard filters are standard width and length that will fit most sump style filtration systems. Housing and filters are sold separately. Everpure Costguard Filters DEV910811 DEV910815 DEV910857 Gallon GPM Flow Rate Micron Rating Fountain Coffee Esp./Capp./Tea Ice Machine Drinking Water Combination Case Qty. Filter Number Reduces/Eliminates CGT10S DEV910813 5,000 1 20 X X 12 Clorine, taste, odor, scale CGT20S DEV910833 10,000 2 20 X X 6 Clorine, taste, odor, scale CGT10 DEV910811 5,000 1 20 X 12 Clorine, taste, odor CGT20 DEV910832 10,000 2 20 X 6 Clorine, taste, odor CG510S DEV910817 6,000 1.7 5 X X 12 Clorine, taste, odor, scale, sediment CG520S DEV910827 12,000 3.3 5 X X 6 Clorine, taste, odor, scale, sediment CG510 DEV910815 6,000 1.7 5 X 12 Clorine, taste, odor, sediment CG520 DEV910825 12,000 3.3 5 X 6 Clorine, taste, odor, sediment CG5310S DEV910857 10,000 2.5 X X 12 Clorine, taste, odor, scale, sediment, cyst CG5320S DEV910867 20,000 4.5 X X 6 Clorine, taste, odor, scale, sediment, cyst CG5310 DEV910853 10,000 2.5 X 12 Clorine, taste, odor, sediment, cyst CG5320 DEV910863 20,000 4.5 X 6 Clorine, taste, odor, sediment, cyst Continuing product improvements may necessitate E-31
Everpure Replacement Filters Sorted by Number Number Gallon GPM Flow Rate Micron Rating Model Reduces/Eliminates EV910008 IN-10 2,400.75 6 Sediment, chlorine, taste, odor, cyst, scale EV910066 IN-6 CGS 700.75 6 Taste, odor, scale EV910067 IN-6 PGS 6 mo..75 N/A 6 Scale EV910068 IN-10-CK 5,000 Taste, odor, scale, slime EV910069 IN-10-CS 3,900.5 6 Taste, odor EV910071 IN-10-CC 2,000.75 6 Taste, odor EV910072 IN-10-NSS 6-12 mo.75 5 6 Sediment EV910073 IN-10-CL1 750.75 1 6 Taste, odor, lead, cyst EV910075 IN-9 CFS 1,500.75 5 6 Taste, odor, scale EV910076 IN-15-CF 5,000.75 5 6 Taste, odor EV910077 IN-15-CFS 5,000.75 5 6 Taste, odor, scale EV910078 IN-15-CR 650 gr..75 6 Hardness, taste, odor EV910079 IN-10-UV 12 mo..75 12 Bacteria, viruses EV910086 IN-12 4,800.75 6 Sediment, chlorine, taste, odor, cyst, scale EV910502 CB20-124E 15,000 5 1 Chloramine, chlorine, taste, odor, cyst EV910521 CB20-302E 20,000 5 1 Chloramine, chlorine, taste, odor, cyst EV910534 CB20-312E 60,000 5 1 Chloramine, chlorine, taste, odor, cyst EV910541 SO-10 N/A 2 N/A 1 Hardness, scale EV910542 SO-20 1500 gr. 2 N/A 0 Hardness, scale EV910545 SO-204 N/A 2 N/A 0 Hardness, scale EV910700 QCP 10L 500.5 5 12 Sediment EV910700 QCP 10L 500.5 12 Chlorine, taste, odor, lead EV910701 QCP 10GAC 1,700.5 5 12 Chlorine, taste, odor, lead EV910701 QCP 10GAC 2,500.5 12 Chloramine, taste, odor EV910702 QCP 10SED --.5 5 0 Chloramine, taste, odor EV910702 QCP 10SEDS Depends.5 5 0 Sediment, taste, odor EV910703 QCP 10TSGAC 2,500.5 5 0 Scale Case Qty. E-32 Continuing product improvements may necessitate
Everpure Replacement Filters Sorted by Number Number Gallon GPM Flow Rate Micron Rating Case Qty. Model Reduces/Eliminates EV910703 QCP 10TSGAC 1,700.5 0 Chloramine, taste, odor, scale EV910837 20" x 4" Big Bowl N/A 50/5 0 Sediment EV910840 20" x 4" Big Bowl N/A 20 25/1 6 Sediment EV953412 EC110 10" Slimline N/A 5 10 0 Sediment EV953426 EC210 20" Slimline N/A 10 10 0 Sediment EV953430 10" ECPI N/A 1 Sediment EV953433 20" ECPI N/A 1 Sediment EV953436 20" ECPI Big Bowl N/A Sediment EV960700 7DBG Depends 1.7 40 1 Extraordinary taste and odor, high turbidity EV960701 7DM 1600 gr..5 0 Scale, high mineral content, low volume application EV960702 7NE Depends.5 1 Buffer/neutralizer for acidic (low ph) water, taste, odor EV960703 7OF Depends.5 1 Iron, sulfer, stains EV960704 7SO 2000 gr..5 1 High mineral content, low volume application EV960705 7TO 30,000 1.5 6 Extraordinary taste and odor, high turbidity EV960710 ESO 6 Depends.5 0 Hardness, buffering, chlorine, cyst, iron, sediment, scale, taste, odor EV960725 ESO 7 Depends.5 0 Hardness, buffering, chlorine, cyst, iron, sediment, scale, taste, odor EV961222 I20002 9,000 1.7.5 0 Sediment, chlorine, taste, odor, cyst, microbial control, scale EV961232 I40002 12,000 1.7.5 0 Sediment, chlorine, taste, odor, cyst, microbial control, scale EV961250 BH2 3,000.5.5 0 Sediment, chlorine, taste, odor, cyst, microbial control, scale EV961256 MC2 9,000 1.7.5 0 Class I particulates, chlorine, taste, odor, cyst EV961310 XC2 12,000 1.7.5 0 Class I particulates, chlorine, taste, odor, cyst EV961321 MH2 9,000 1.7.5 0 Sediment, chlorine, taste, odor, cyst, microbial control, scale EV961706 2CB5K 3,000 1 5 0 Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure) EV961711 4CBS 6,000 1.7 5 0 Sediment, chlorine, taste, odor, high turbidity (for low flow/pressure) EV961721 4CB5S 6,000 1.7 5 0 Sediment, chlorine, taste, odor, scale EV961722 2CB5S 3,000 1 5 0 Sediment, chlorine, taste, odor, scale EV961736 4CB5K 6,000 1.7 5 0 Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure) EV961776 7CB5K 10,000 2.5 5 0 Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure) EV961802 OCS2 1,500.5.5 0 Sediment, chlorine, taste, odor, cyst, microbial control, scale EV961811 7CB5 10,000 2.5 5 0 Sediment, chlorine, taste, odor, high turbidity (for low flow/pressure) EV961821 7CB5S 10,000 2.5 5 0 Sediment, chlorine, taste, odor, scale Continuing product improvements may necessitate E-33
Everpure Replacement Filters Sorted by Number Number Gallon GPM Flow Rate Micron Rating Case Qty. Model Reduces/Eliminates EV961901 OW200L 480.5.5 0 Sediment, chlorine, taste, odor, lead, scale, cyst, THMs EV962828 MC2 Quad Kit 36,000 6.7.5 0 Class I particulates, chlorine, taste, odor, cyst EV962829 XC2 Quad Kit 48,000 6.7.5 0 Class I particulates, chlorine, taste, odor, cyst EV963401 OW2-Plus 1,000.5.5 0 Sediment, chlorine, taste, odor, cyst, microbial control, lead, scale EV963501 OW4-Plus 2,000.5.5 0 Sediment, chlorine, taste, odor, cyst, microbial control, lead, scale EV963701 Microguard Pro 2 2,200 1.15 0 Sediment, chlorine, taste, odor, bacteria, asbestos, cyst EV963702 Microguard Pro 4 3,600 1.15 0 Sediment, chlorine, taste, odor, bacteria, asbestos, cyst EV979902 SS-10 6 mo. 6 N/A 0 Hardness, scale EV979932 SS-IMF N/A 6 N/A 1 Hardness, scale EV997042 MC2 Triple Kit 27,000 5.5 0 Class I particulates, chlorine, taste, odor, cyst Everpure Water System Cleaning Accessories Number Description EV960800 4JT flushing/sanitizing cartridge for ScaleKleen, bleach, or other sanitizing agent EV960810 2JT flushing/sanitizing cartridge EV979831 ScaleKleen scale remover, 1.75 oz. EV979833 ScaleKleen scale remover, 7 oz. EV979835 ScaleKleen scale remover, 2.2 lb EV910091 HFC-10 deliming agent EV910091 EV960800 E-34 Continuing product improvements may necessitate
Everpure Water System Heads EV910721 EV910722 EV910723 EV433921 EV925617 EV925924 EV927241 EV927222 EV927224 EV927223 EV933611 EV933726 Model Number Shut-Off Valve Mtg. Bracket Connection Flushing Valve Pressure Gauge QCP1 Single Head EV910721 Yes No 1/4" QCF No No QCP2 Twin Head EV910722 Yes No 1/4" QCF No No QCP3 Triple Head EV910723 Yes No 1/4" QCF No No QCPC (1 head no shut-off) EV910720 No No 1/4" QCF No No QL1 Single Head EV925618 No Yes 3/8" MPT No No QL1 Single Head EV925617 No Yes 3/8" QCF No No QL3B Single Head EV925924 Yes Yes 3/8" MPT No No QC71 Single Head EV927241 Yes Yes 3/8" MPT Yes Yes QC71 Twin Parallel Head EV927222 Yes Yes 3/4" MPT Yes Yes QC71 Twin Plumbed Head EV927224 Yes Yes 3/4" MPT Yes No QC71 Triple Parallel Head EV927223 Yes Yes 3/4" MPT Yes Yes QC71 Quad Parallel Head EV933611 Yes Yes 3/4" MPT Yes Yes QC71 Quad Head EV933726 Yes Yes 3/4" MPT Yes Yes Claris Head 3/8" BSP EV4339-21 Yes Yes 3/8" BSP Yes No Claris Head 3/8" QCF EV4339-23 Yes Yes 3/8" QCF Yes No Claris Head 1/4" QCF EV4339-25 Yes Yes 1/4" QCF Yes No Everpure Water System Accessories QCF = quick connect fitting, comparable to John Guest fittings Number DEV701344 EV982010 EV8300101 EV907550 EV933650 EV311469 EV126122 Description Smartworks water test kit Faucet kit Bottled water delivery system Filter usage monitor Surge tank, 9 gallon with fittings and tubing Spacer for SS-IMF cartridge Titration kit for Claris system Continuing product improvements may necessitate E-35
Bottled Water Dispenser At just 6" x 8" the Flojet Inlet Bottled Water Dispensing System is compact, affordable and perfect for dispensing bottled water to coffee machines, beverage dispensers, vending machines and carts in remote locations where water supply is inaccessible. This system has a universal seal cap, float switch for automatic shut-off when bottle is empty, built-in check valve to prevent back flow, and 20' discharge hose. Available in single or dual inlet. The dual inlet model has a T to draw from two bottles simultaneously. Flow rate: 1.0 GPM. Maximum pressure: 40 psi. BW1000A Number BW1000A BW1020A BW3000A BW3020A BW1520A BW3520A 21000633A 91006466A 21000006B 91006698A Description Single inlet, 1 GPM pump, 115 Volt, 20' discharge hose 1/4" OD Dual inlet, 1 GPM pump, 115 Volt, 20' discharge hose 1/4" OD Single inlet, 12V DC with 12" lead wires Dual inlet, 12V DC with 12" lead wires Dual inlet, appliance controller interface, 115 Volt Dual inlet, appliance controller interface, 12 Volt DC with 12" lead wires Conversion kit, single to dual inlet Conversion kit, legacy to A.C. interface Appliance controller Daisy chain (multi-hook up) 4-6 pin RJ-1, 9' cable Appliance Controller Unit is designed to work with applications drawing water from a reservoir or a bottled water system such as coffee machines and carbonator pumps at soft drink kiosks. It will sense water empty signal (0-5 VDC) coming from the water level sensor and turn connected devices ON or OFF. Audible alarm. 1 year warranty. Appliance controller can be mounted over or under the counter. Operating temperature: 32 F to 158 F. RJ-11 4 pins: daisy chain configuration. RJ-11 6 pins: BW interface. 6 pin RJ-11 cable: 9'. 2 AC outlets. 115V. Number Description 91006467A Appliance controller 91006698A 4-6 pin RJ-11 cable, 6' Lancer is a registered trademark of Lancer Corporation, San Antonio, Texas. SHURflo is a registered trademark of SHURflo, LLC, Cypress, California. McCann s is a registered trademark of McCann s Engineering, a Manitowoc Company, Los Angeles, California. Procon is a registered trademark of Procon Products, Standex International Corporation, Murfreesboro, Tennessee. Fluid-o-Tech is a registered trademark of Fluid-o-Tech International, Inc., Plantsville, Connecticut. Flojet is a registered trademark of ITT Industries, Foothill Ranch, California. CUNO, ScaleGARD, and Recipe Quality Water are trademarks of CUNO Incorporated, a 3M Company, Meriden, Connecticut. 3M is a trademark of 3M Company. Selecto is a registered trademark of Selecto, Inc., Suwanee, Georgia. Everpure is a registered trademark of Everpure, Inc., Hanover Park, Illinois. E-36 Continuing product improvements may necessitate