Product Version Gro-Wall PRO Document ID xxxx VERTICAL GARDEN SYSTEM PRO Assembly, Installation & Watering Guide www.atlantiscorp.com.au
Additional Materials Required (Not Included) Irrigation Components Typical 13mm and 19mm irrigation fittings and connectors are compatible with Gro-Wall. Poly Irrigation Pipe 90 0 Angle Connector End Cap Connector T Connector (3 way) Water Tap Connector Garden Hose Connector Poly Clamp Stainless Steel Clamp (Recommended) Various irrigation drip heads are available for use within the Gro-Wall adjustable or fixed flow rates. For most installations online drippers of fixed flow rates ranging from 2 L/h, 4L/h and 8 L/h are sufficient. Adjustable Online Dripper Fixed Flow Rate Online Dripper Fixtures for attaching Gro-Wall to wall structures Gro-Wall can be easily fixed to concrete, brick, masonry, sheet metal, timber and other surfaces using appropriate fasteners. Note: Allow for 23mm depth when fixing the fastener through the Gro-Wall Long Plate and Locking Clip. Self Tapping Screws, Wood or Metal Galvanized self tapping screws are recommended. Shaft length will be determined by wall surface. 7/32 (5.5mm) diameter shaft 5/16 (8mm) Hex Head with 9/16 (14.5mm) Flange 7/32 (5.5mm) Shaft Diameter 5/16 (8mm) Head 9/16 (14.5mm) Flange Steel & Sheet Metal Wood Concrete, Brick & Masonry 8mm shaft anchor bolt. Flanged Hexagon Nut (Recommended) 8mm Shaft Diameter 13mm Flange 10mm Head Phillips Countersunk Soil Components Various soil components will be required for planting within the Gro-Wall bags. The components will vary depending what soil mix design is chosen. Typically soil mixes consist of organic matter (potting mix), fertilizers and inorganic materials such as volcanic rock (Pearlite, Vermiculite) and washed sand. Always consult your local nursery or garden centre for more accurate soil compositions. Potting Mix (Organic Matter) Fertilizer (Pelletized) Inorganic Material (Pearlite, Vermiculite) Inorganic Material (Washed Sand)
Gro-Wall Kit Contents Gro-Wall PRO kits contain components for 6 modules. 52mm Half Tile Gro-Wall Pot 52mm Drainage Cells Gro-Wall PRO Dimensions & Orientation Single Gro-Wall PRO modules are 000mm in width, 000mm in depth and 000mm in height. A single Gro-Wall PRO module contains 2 plant cells. 270mm 487mm 265mm
Assembly of 1 Column of Gro-Wall PRO module 1. Place 1bottom tile flat 2. Connect a divider on one side 3. Connect a second divider on the other side 4. Connect the top plate Completed 1 Gro-Wall PRO Module Assembly of 2 Columns of Gro-Wall PRO module Note: Always start with the width of the structure and build UP from that. It is not possible to connect 2 or more columns together once 1 (one) column is assembled 1. Connect 2 bottom tiles 2. Connect 4 dividers... 3.... at the ends of each tile 4. Connect the top plates Completed Gro-Wall PRO 2 columns
Assembly of 3 Columns of Gro-Wall PRO module 1. Connect 3 bottom tiles 2. Connect 6 dividers... 3.... at the ends of each tile 4. Connect the top plates Completed Gro-Wall PRO 3 columns 1, 2 & 3 Columns of Gro-Wall PRO module
Irrigation System Overview The Gro-Wall PRO system enables the caretaker to tailor the watering requirements to suit various environmental conditions, seasonal changes and plant species. Typical Irrigation Setup 1 Gro-Wall kit irrigation requirements: 6m length of poly irrigation hose (13mm or 19mm) 18 x Online Drippers 6 x Poly end cap connectors 5 x Poly T (3 way) connectors 3 x Poly 90 0 angle connectors 1 x Poly water tap connector 26 x Hose Clamps (poly or stainless steel) Fastening the Gro Wall PRO The clips can be attached to the module and bolted onto a structure The clips can be placed inside or outside the module
Irrigation Installation Insert the irrigation tube and cut to size at the ends Puncture the tube from the top first Punctured tube Insert nozzle tightly When all nozzles are connected Insert the end plug of that row..and turn 90 o forwards Insert the Tee-Connector at the other end An end angle plug has to be inserted at the top module. Connect all tee-connectors on the side with a piece of 13mm tube and clamp
VERTICAL GARDEN SYSTEM PRO Note: Atlantis products are manufactured from high quality recycled materials, carefully selected and under strict quality control procedures. The strength could vary slightly due to raw material, country of manufacture, manufacturing process and external conditions. All trademarks are the property of Atlantis Water Management Australia. Safety Factors: Engineers, designers and geotechnical engineers should design and calculate safety factors to a serviceable limited state to suit specific project. In case of doubt, consult your nearest distributor or Atlantis representative. Disclaimer: All information provided in this publication is correct to the best knowledge of the company and is given out in good faith. This information is intended only as a general guide, no responsibility can be accepted for any errors, omissions or incorrect assumption. As each project is unique, and as Rebirth Pty Ltd, Atlantis Water Management, Atlantis Corporation Pty Ltd and its distributors and agents world wide have no direct control over the methods employed by the user in specifying, installing or supervising of its products hence no responsibility is accepted by Rebirth Pty Ltd, Atlantis Water Management, Atlantis Corporation Pty Ltd and its distributors and agents world wide. Users should satisfy themselves as to the suitability of the product for their purpose. All product designs, and specification are subject to change without further notice. All Atlantis products are tested in approved NATA laboratories, and safe allowed tolerances should be practised in the actual field, to compensate for any unforeseen situations, on site and on products. All material contained within this brochure is subject to copyright, and belongs to Humberto E. Urriola and Christian Urriola, Rebirth Pty Ltd Australia. No part of this brochure may be reproduced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without prior written permission of Rebirth Pty Ltd. Australia, Atlantis Water Management, Atlantis Corporation Pty Ltd. Copyright @ 2009.