MATERIAL SAFETY DATA SHEET Laser Bonding Technology Laser Bonding Technology 5336 Vincent Avenue Los Angeles, CA 90041 Emergency Telephone Number: CHEMTREC: 1 800 424 9300 (OUTSIDE US): 1 703 527 3887 COMPANY: 1 844 577 7772 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY Product Name: CAS No.: Recommended Use: Product Code: Date of Preparation: LaserBond 100 Laser Bonding Material Mixture Undustrial Use Only LBM 100 08/02/2013 2. HAZARDS IDENTIFICATION Emergency Overview Warning Avoid contact with skin and eyes. May cause irritation to eyes. Harmful if swallowed or inhaled. HMIS NFPA 704 Color: Black Health: 2 2 Physical State: Paste Flammability: 0 0 Odor: Characteristic Physical Hazard: 0 0 Potential Health Effects PPE: B Principle routes of exposure: Eye contact: Skin contact: Inhalation: Ingestion: Chronic Toxicity: Inhalation, ingestion, skin or eye contact May cause eye irritation Irritating to skin; prolonged contact may cause dermatitis May be harmful if inhaled. Vapors may be irritating to eyes and lungs May be harmful if swallowed and irritate digestive tract Long term exposure may cause loss of appetite, weight loss, liver damage. Combined exposure to ethanol and certain other chemicals may result in increased toxic effects. 3. COMPOSITION/INFORMATION ON INGREDIENTS Component CAS Number Weight % Proprietary Molybdenum Compound None - Trade Secret 50-60% 7732-18-5 40-50% Specific chemical identities are being withheld as a trade secret (29 CFR 1910.1200) Product Name: LaserBond 100 Page 1 of 5
4. FIRST AID MEASURES Eye contact: Skin contact: Inhalation: Ingestion: Notes to physician: Rinse immediately with water, also under eyelids. Get medical attention if needed Wash off immediately with soap and water. Remove and wash contaminated clothing before re-use. If symptoms persist, call a physician. Move to fresh air. If breathing is difficult, give oxygen. If symptoms persist, call a physician. Drink plenty of water. Do not induce vomiting. Consult a physician, if necessary Treat symptomatically 5. FIRE FIGHTING MEASURES Flash Point: Suitable extinguishing media: Hazardous decomposition products under fire conditions: Special protective equipment for firefighters: Unusual hazards: Non-Combustible Use dry chemical, CO2, water spray or foam Carbon oxides and metal compounds As in any fire situation, wear self-contained breathing apparatus (pressure-demand NIOSH approved or equivalent) and full protective gear Fumes are heavier than air and may spread along flooring. 6. ACCIDENTAL RELEASE MEASURES Personal precautions: Environmental precautions: Clean up methods: Remove all non-essentialpersonnel from the affected area. Ensure adequate ventilation. In case of insufficient ventilation, wear suitable respiratory equipment. Avoid contact withskin, eyes and clothing. Wear personal protective equipment. Prevent further leakage if safe to do so and prevent product from entering drains. Do not flush into surface water or sanitary sewer system. Do not allow material to contaminate ground water system. Wear protective equipment. Absorb spill with inert materials (e.g. dry sand/earth) and place in a chemical waste container. Clean contaminated surface thoroughly and dispose of promptly. 7. HANDLING AND STORAGE Handling: Storage: Handle in accordance with good hygiene and safety practices. Use only in well ventilated area and use protective equipment. Avoid contact with skin, eyes and clothing. Do not eat or drink in areas of use. Wash thoroughly after handling. Keep containers tightly closed in dry, well ventilated area. Product Name: LaserBond 100 Page 2 of 5
8. EXPOSURE CONTROLS / PERSONAL PROTECTION Component OSHA PEL ACGIH Proprietary Molybdenum Compound 20 mppcf TWA Not 3 5 mg/m TWA respiratory fraction Not Ventilation: Eye protection: Skin protection: Hand protection: Respiratory protection: Personal hygiene protection: Local exhaust ventilation should be provided to keep product concentrations of dust, fumes and vapors below acceptable exposure limits. Discharge from the ventilation system should comply with all local air quality regulations. Safety glasses with side shields should be worn to protect against exposure. Lightweight protective clothing should be worn. Chemically resistant rubber or latex gloves should be worn. Appropriate respiratory protection should be used when exposure to airborne fumes may exceed acceptable limits. Respirators should be selected and used in accordance with OSHA Subpart I (29 CFR 1910.134). Seek professional advice prior to the selection and use of respiratory equipment. Wash hands before work breaks and at the conclusion of work. 9. PHYSICAL AND CHEMICAL PROPERTIES Color: Odor: Boiling point/range: Melting point/range: Bulk density : Black Characteristic 13 lb/gal Physical state: Paste solubility: Specific gravity (water=1) VOC content < 1% ph: 10. STABILITY AND REACTIVITY Stability: Polymerization: Hazardous decomposition: Materials to avoid: Conditions to avoid: Stable at normal conditions None under normal processing and use None under normal use. Thermal decomposition can lead to release of irritating gasses and vapors, carbon oxides, molybdenum and metal compounds Strong oxidizing agents. Strong acids and strong bases. Closed and/or non ventilated areas. 11. TOXICOLOGICAL INFORMATION No toxicological data available for this product Product Name: LaserBond 100 Page 3 of 5
No ecological data available for this product 12. ECOLOGICAL INFORMATION 13. DISPOSAL CONSIDERATIONS Disposal of waste: In accordance with Federal, State and Local environmental laws and regulations 14. TRANSPORT INFORMATION DOT (USA) TDG (Canada) IMDG IATA 15. REGULATORY INFORMATION U.S. Regulations TSCA: Not subject to TSCA 12(b) Export Notification This product or its ingredients have been evaluated for New Jersey, Pennsylvania and California Prop 65 for supplier notification requirements. Substances subject to notification requirements are listed below. Molybdenum Compounds PARTK (PARTK) (PARTK) Molybdenum Compounds NJRTK (NJRTK) (NJRTK) Molybdenum Compoundsl State Regulation - CA Prop 65 Carcinogen - Developmental Toxicity Product Name: LaserBond 100 Page 4 of 5
SARA 313 (50-60%) Molybdenum Compounds (40-50%) US - CERCLA/SARA - Section 313 - Emission Reporting 1.0% de minimis concentration 1.0% de minimis concentration Canadian WHMIS WHMIS hazard class: Non Flammable Paste D2B Toxic materials Canadian Ingredients Disclosure List (IDL): Canada - WHMIS Ingredient Disclosure Molybdenum Compounds 1 0.1 International Inventories U.S. EPA TSCA 8(b): Canada DSL/NDSL list: Europe (EINECS): Philipines (PICCS): Japan (ENCS): Korea )KECL): China (IECS): Australia (AICS): New Zealand (NZIoC): or exempt All ingredients are listed on the DSL or NDSL or exempt or exempt 16. OTHER INFORMATION For industrial Use Only Prepared by: Laser Bonding Technology Technical Center Disclaimer: The information and recommendations contained in this Material Data Safety Sheet have been compiled from sources believed to be reliable and to represent the most reasonable current opinion on the subject matter, No warranty, guarantee or representation is made as to the correctness or sufficiency of the information. The user of this product must decide what safety measures are reasonable and necessary to safely use this product, either alone or in combination with other products and determine its environmental regulatory compliance obligations under any applicable laws or regulations. **** END OF MATERIAL SAFETY DATA SHEET **** Product Name: LaserBond 100 Page 5 of 5