Gas barrier and damp proofing accessories

Gas barrier and damp proofing accessories Gas barriers and damp proofing 2-4 5 Gas barrier and damp proof membrane cavity tray systems and accessories Damp Proof coursing accessories 1 Call. 01405 765567 Email. sales@timloc.co.uk www.timloc.co.uk

Gas barrier and damp proof membrane cavity tray systems and accessories Working in conjunction with radon, methane, CO2 and hydrocarbon gas barrier systems to contain rising gasses across the footprint of the building. Let us take the load with our free Cavity Tray specification and scheduling service. Top hat collar Radon sumps Corner units Contact the Timloc Technical Team for more information. Use Products in the system In areas outlined in BRE document Radon guidance on protective measures in new dwellings When gas protection is required across the footprint of the building Crossing cavity wall constructions to maintain gas barrier integrity Forming internal perimeter trays to allow membranes continuity Collars for service pipe protrusions Following a risk assessment where the requirement is for a good gas protection measure against Radon, Co2, Methane and Hydrocarbon To be designed and installed in a continuous system around the whole building perimeter Features and benefits Preformed mouldings eliminate the need for site fabrication to prevent errors through poor workmanship Easy to handle, flexible, tough, durable and puncture resistant Can be used for multi-storey or high-loading applications will not extrude under high loads up to the point of compression failure of wall Wide range of standard components with special tailor made accessories also available Fully itemised scheduling service Preformed cavity tray system Works by reducing on site exposure to the membrane through the use of independent performed and rigid cavity trays installed to the perimeter of the building, in both the cavity wall with our PCT range and installed at the slab edging with our SPT range. PCT Range - Horizontal cavity wall perimeter trays Supplied in 2.5 metre lengths and manufactured from heavy duty 2mm polypropylene. They should be installed continuously around the external perimeter of a building to allow the membrane to be laid at a later stage and so prevent damage as building works proceeds. SPT Range Horizontal slab perimeter trays Supplied in 2.5 metre lengths and manufactured from heavy duty 2mm polypropylene. They should be installed continuously around the internal slab pour area allowing the membrane to be laid at a later stage and so prevent damage as building work proceeds. Quality Manufactured to BS EN ISO 9001 and BS EN ISO 14001 Satisfies all NHBC requirements Meets BRE requirements Complies with Building Regulation Approved Documents C1 and C2 Meets all relevant British Standards Material and colour choice Formed in 2mm medium density polyethylene and/or polypropylene Available in black only Corners - PCT and SPT ranges Available in both SPT and PCT ranges and manufactured from heavy duty 2mm polyethylene. The standard corners are 90 but a wide range of options are available and selection is by cavity size, wall construction and damp roof course or slab rise required. Page 1 of 3 see next page Call. 01405 765567 Email. sales@timloc.co.uk www.timloc.co.uk 2

Gas barrier and damp proof membrane cavity tray systems and accessories Working in conjunction with radon, methane, CO2 and hydrocarbon gas barrier systems to contain rising gasses across the footprint of the building. Change of level units Top hat collar Stopends & change of level units Available in the PCT range and manufactured from heavy duty 2mm PP. Suitable if breaks appear in the natural run of the cavity tray system, and available in cavity size and rise options with 75, 150 and 225mm steps. Radon sumps (RSUMP01) Prefabricated sumps are required when a sub floor depressurisation is required under full radon protection. The sump is installed beneath the floor slab in non suspended floor applications and vented to atmosphere via a connecting 110mm drainage pipe to an external source and capped off with proprietary products i.e. air bricks & telescopic under floor vents or roof vents. Jubilee clips size 6 (110mm - 140mm) Jubilee clips size 7 (135mm - 160mm) Televent gas sleeve tray (TST01) For use when telescopic under floor vents need to pass through a perimeter cavity and still maintain gas tight integrity. TPT01 Radon sump illustrating horizontal and vertical 110mm soil pipe for venting with top hat collar Threshold internal protection tray (TPT01) Designed for detailing rebated areas inside door threshold to maintain water and gas tight integrity without having to trim membrane to fit. Due to possible variations in size, threshold dimensions will be required. The minimum number of sumps required is one per dwelling, but this will be dependent on the foundation construction of the building. 3x sumps req. 4x sumps req. single sump req. Column cloak Vented load bearing masonry Non-vented load bearing masonry Column cloaks (made to order) Non standard applications can require gas and water integrity around columns and stanchions. Timloc will design and produce rigid preformed units that are user friendly: simply contact our technical department. Top hat pipe collars (TH055, TH082, TH110, TH135, TH160) Top hat pipe collars are available in sizes from 55mm to 160mm. A standard range of preformed pipe sleeves that are designed to have sealing tape applied to the unit base to offer a unit for sealing to a gas barrier and at the intersection of pipe projections. Common applications are for soil /service pipes passing vertically via a gas barrier or membrane to maintain a continuous seal. Top hats are suitable for installation at ceiling level for pipe protrusions to assist in reducing air leakage. All sealing tapes (GTAPE 03) and fixing bands (JCLIP 6 or 7) are supplied separate to top hat units. Gastite sealing tape (GTAPE03) A 2mm x 50mm wide double sided modified polymer strip, protected on both sides with a silicone release paper. The principle is to apply between parts of the system in continuous joint lengths to achieve a gas tight seal. Also available in 100mm width rolls (GTAPE01). Girth tape (GTAPE02) A single sided 75mm wide tape with an aggressive adhesive to one side, used to cap overlaps that have been sealed with gastite tape to prevent uplift of joints when concrete slab or screed is poured. Page 2 of 3 see next page 3 Call. 01405 765567 Email. sales@timloc.co.uk www.timloc.co.uk

Gas barrier and damp proof membrane cavity tray systems and accessories Working in conjunction with radon, methane, CO2 and hydrocarbon gas barrier systems to contain rising gasses across the footprint of the building. Let us take the load with our free Cavity Tray specification and scheduling service. Contact the Timloc Technical Team for more information. Page 3 of 3 How to order Timloc can prepare a comprehensive schedule and quotation service. Forward full working drawings and specifications to our technical department Orders can be established from written quotations by stipulating number issued Bill of quantity (Gas barrier accessories) F30 Accessories/sundry items for brick/block/stone walling Clause 360 GAS RESISTANT CAVITY TRAY ACCESSORIES Manufacturer: Timloc Building Products, Rawcliffe Road, Goole, East Yorkshire, DN14 6UQ. Tel: 01405 765567, Fax: 01405 720479. Web: www.timloc.co.uk Reference: e.g. Top hat pipe collar Size: e.g. 110mm Product code: e.g. TH110 Use: For use in all types of floor construction to protect buildings against gas penetration from the ground. To cover the full footprint of the building and to incorporate proprietary accessories for pipe, vent protrusions. Product codes Active-guard radon barrier accessories Product code Top hat pipe collars 55mm - 160mm TH055 TH160 Jubilee clips size 6, 7 JCLIP 6 or 7 Radon sump 350mm x 350mm RSUMP01 Threshold internal protection tray 930mm TPT01 Televent gas sleeve tray (cavity tray profile req.) TST01 Gastite sealing tape 50mm x 15mtr GTAPE03 Girth tape 75mm x 33mt GTAPE02 SPT150 Slab perimeter cavity tray 150mm rise 5107 SPT150 Corner cavity tray 90-150mm rise 5122 SPT225 Slab perimeter tray 225mm rise 5108 SPT225 Corner cavity tray 90-150mm rise 5123 Product codes to suit cavity widths of PCT150 Perimeter cavity tray 150mm rise 5101 5102 5103 PCT150 External 90 corner cavity tray 5110 5112 5114 PCT150 Internal 90 corner cavity tray 5111 5113 5115 PCT150 Cavity tray stopend RH 5130 5132 5134 PCT150 Cavity tray stopend LH 5131 5133 5135 PCT150 Change of level 75mm step 9060 9063 9066 PCT150 Change of level 150mm step 9061 9064 9067 PCT150 Change of level 225mm step 9062 9065 9068 PCT225 Perimeter cavity tray 225mm rise 5104 5105 5106 PCT225 External 90 corner cavity tray 5116 5118 5120 PCT225 Internal 90 corner cavity tray 5117 5119 5121 PCT225 Cavity tray stopend RH 5136 5138 5140 PCT225 Cavity tray stopend LH 5137 5139 5141 PCT225 Change of level 75mm step 9070 9073 9076 PCT225 Change of level 150mm step 9071 9074 9077 PCT225 Change of level 225mm step 9072 9075 9078 Call. 01405 765567 Email. sales@timloc.co.uk www.timloc.co.uk 4

Damp proof coursing accessories Products allowing a complete horizontal cavity tray system to be formed Change of level unit Joint support Stopend (full height) Jointing tape Sloping stopend (75mm high) Muti stopend (75mm high) Corner unit Use Wherever DPC is used to form a horizontal cavity tray Features and benefits One piece seamless mouldings eliminate the need for site fabrication to prevent errors through poor workmanship Easy to handle, flexible, tough, durable and puncture resistant Fully compatible with 9000 polymeric dpc Can be used for multi-storey or high loading applications - will not extrude under loads up to the point of compressive failure of wall Wide range of standard components with special, tailor-made accessories also readily available Quality Satisfies all NHBC requirements Manufactured to BS EN ISO 9001 and BS EN ISO 14001 Complies with all relevant Building Regulations Meets all relevant British Standards Material and colour choice 9000 polymeric dpc accessories are moulded in 2.0mm thick medium density polyethylene. They do not contain any pitch, tar or bitumen. Available in black only Products in the system Corner units For use where a cavity tray must turn the corner of a building Change of level units For use where the cavity tray steps up or down along its run Stopend units For sealing off the ends of the cavity tray at its start and finish Jointing tape For sealing lapped joints in the DPC or for sealing the DPC on to the accessories Joint supports For fitting below lapped joints in the DPC to provide support and allow the jointing tape to be sealed correctly Installation advice As with the DPC, accessories should always be bedded on to fresh mortar, never dry bedded. The masonry laid over the DPC should also be bedded on to fresh mortar so that the DPC is approximately half way through the thickness of the mortar joint DPC must be lapped on to the accessory by a minimum of 100mm All lapped joints must be fully sealed with jointing tape. It is essential that the jointing surfaces are clean and dry or the jointing tape will not seal correctly Please see technical section for more details. How to order State the wall construction, cavity width and the rise which is required across the cavity If you need a special, tailor-made accessory - please supply a dimensioned sketch detailing your requirements Bill of quantity F30 Accessories/sundry items for brick/block/stone walling Clause 380 PREFORMED DPC/CAVITY TRAY JUNCTION CLOAKS/STOPENDS Manufacturer: Timloc Building Products, Rawcliffe Road, Goole, East Yorkshire, DN14 6UQ. Tel: 01405 765567, Fax: 01405 720479. Web: www.timloc.co.uk Type(s) and location(s): Preformed stopend units to be positioned at the start and finish of a run of cavity trays. Seal all laps with dpcs and/or cavity trays using adhesive/mastic in accordance with manufacturer s recommendations to ensure a fully watertight installation. Reference:... 9000 Stopend Unit (RH/LH) Cavity Rise:... (150mm or 225mm) Cavity Width:... (50mm, 75mm and 100mm) Product codes Built in at 150mm rise Handing Product codes to suit cavity widths of Stop end units - Full height RH 9010 9012 9014 Stop end units - Full height LH 9011 9013 9015 Stop end units - 75mm high (sloping) RH 9045 9047 9049 Stop end units - 75mm high (sloping) LH 9046 9048 9050 Stop end units - 75mm high Multi 9024 9024 9024 Corner units - 9001 9002 9003 Joint supports - 9026 9027 9028 Change level unit - 75mm step Multi 9060 9063 9066 Change level unit - 150mm step Multi 9061 9064 9067 Change level unit - 225mm step Multi 9062 9065 9068 Jointing tape - 22.5m roll - 9040 Built in at 225mm rise Handing Product codes to suit cavity widths of Stop end units - Full height RH 9018 9020 9022 Stop end units - Full height LH 9019 9021 9023 Stop end units - 75mm high (sloping) RH 9051 9053 9055 Stop end units - 75mm high (sloping) LH 9052 9054 9056 Stop end units - 75mm high Multi 9024 9024 9024 Corner units - 9004 9005 9006 Joint supports - 9030 9031 9032 Change level unit - 75mm step Multi 9070 9073 9076 Change level unit - 150mm step Multi 9071 9074 9077 Change level unit - 225mm step Multi 9072 9075 9078 Jointing tape - 22.5m roll - 9040 5 Call. 01405 765567 Email. sales@timloc.co.uk www.timloc.co.uk