DANGEROUS GOODS PANEL (DGP) MEETING OF THE WORKING GROUP OF THE WHOLE

DGP-WG/09-IP/1 30/3/09 DANGEROUS GOODS PANEL (DGP) MEETING OF THE WORKING GROUP OF THE WHOLE Auckland, New Zealand, 4 to 8 May 2009 Agenda Item 6: Other business DEVELOPMENT OF STANDARDS FOR ELECTRONIC TRANSMISSION OF THE DANGEROUS GOODS TRANSPORT DOCUMENT (Presented by D. Brennan) SUMMARY This paper is provided as a follow-up to the changes incorporated into the 2009-2010 edition of the Technical Instructions with respect to provisions for electronic data transmission of the information required on the dangerous goods transport document. 1. INTRODUCTION 1.1 At the twenty-first meeting of the Dangerous Goods Panel, (DGP/21), the DGP agreed to revisions to Part 5;4 and Part 7;1 of the Technical Instructions to permit the use of electronic data transmission in lieu of a paper dangerous goods transport document and set out some conditions with respect to the use of electronic data for the information required by Part 5;4. 1.2 Following on from this work at the DGP similar proposals were put to the UN Subcommittee of Experts at the thirty-fourth session of the Subcommittee in December 2008. The proposals were adopted, which will result in changes being incorporated into the 16 th revised edition of the UN Model Regulations. 1.3 In December 2008, IATA established a task force to develop the Shipper s Declaration for Dangerous Goods (dangerous goods transport document) data standards to support the IATA e-freight project. Given the decision of the Subcommittee to adopt provisions to facilitate the use of electronic data transmission, as well as the belief that any electronic data standard should be truly multi-modal, the task force included members representing shippers, freight forwarders, solutions providers, maritime transport (VOHMA) and airlines as well as representatives from UN Centre for Trade Facilitation and Electronic Business (CEFACT) and the UNECE Secretariat. While there is no person identified to represent road and rail transport, a number of the representatives have experience with ADR and were able to provide a road transport perspective for the data requirements. In establishing this task force IATA accepted that the use of electronic data transmission for the information required on the dangerous goods transport (6 pages) DGPWG.09.IP.001.6.en.doc

DGP-WG/09-IP/1-2 - document will always be subject to the national laws in the applicable State, not withstanding what may be in the Technical Instructions. 1.4 From December 2008 until late March 2009 the task force convened almost weekly by teleconference, and one face-to-face meeting in Geneva in February 2009, to identify and document all of the data elements that will need to be incorporated into the standards for an electronic dangerous goods transport document. The basis for the discussions has been the Model Regulations together with the ICAO Technical Instructions, IATA Dangerous Goods Regulations, IMO IMDG and ADR to identify the modal differences/additions. 1.5 The initial work of the task force to identify and document all of the required data elements was completed in late March 2009 with V 1.0 of the draft functional specification, copy attached. 1.6 The next phase in the work is the development of an ML schema that will incorporate all of the possible data elements in a structure that can be used to transmit the information required in a dangerous goods transport document. The naming and structure of this ML schema will be based on the UN CEFACT Core Component Library as well as the UN CEFACT ML naming and design rules standards to ensure that the ML schema complies with the defined international standards. 1.7 Once developed, the ML schema will be tested against actual completed dangerous goods transport documents to validate that the content and structure of the schema can handle real-world shipments. 1.8 This testing phase will be followed by a proof of concept phase where actual dangerous goods consignments will be transported from consignor to consignee in parallel with a paper dangerous goods transport document to verify that all parties in the supply chain are able to manage a dangerous goods consignment using electronic data in lieu of the paper document. The target for the proof of concept is for this to commence by the fourth quarter of 2009. 2. ACTION 2.1 The DGP-WG is invited to note the progress of this work and is invited to pass this information to any parties to whom the information may be of interest.

- 3 - DGP-WG/09-IP/1 Functional Specifications s SHIPPERS' DECLARATION FOR DG HEADER M 1:1 Grouping Element Shipper's Reference Number O 0:1 AN an 35 Reference number assigned by the shipper 1140 Applies Freight Forwarder's Reference Number O 0:1 AN Reference number assigned by the freight forwarder 1460 Booking Number O 0:1 AN Booking reference number of the carrier 1016 Reference Documents O 0:n Grouping Element Document Reference Number M 1:1 AN Contains the Number being referenced within the document (e.g. Air Waybill number) 1004 Document Type O 0:1 AN Contains the Type of the referenced document. UN EDIFACT 1001 Document/message name, code list. CODED EDIFACT 1 740 1001 Document Name M 1:1 AN Contains the Name of the referenced document. Free Text or the UNEDIFACT 1001 Document/message name, code list can be used. CODED EDIFACT 1 Shipper Details M 1:1 Grouping Element Applies Shipper Internal ID O 0:1 AN Internal ID assigned to the Shipper. 3031 042 Agency d O 0:1 AN Reference identifying the Standard ID. UNEDIFACT 3055 list responsible agency code CODED EDIFACT 3 EAN Shipper Standard ID O 0:1 AN The Standard ID is used to identify the Shipper using a 3rd Party Identifier such as EAN, DUNS etc. Shipper Name And Address M 1:1 Grouping Element Contains the Shipper's name or legal identity. In case additional names need to be specified, the different names should be separated by Shipper Name M 1:1 AN an 35 3030 041 a specific character. PO Box O 0:1 AN Contains the post office box number. 3042 239 Contains the street address. In case additional street names need to be specified, the different names should be separated by a specific Street M 1:1 AN an 35 3042 239 character. Department O 0:1 AN Contains the company department name or number. 3412 246 Zip/Postal O 0:1 AN an 9 Contains the ZIP/Postal corresponding to the street address. 3251 245 Region Name O 0:1 AN an 9 City Name M 1:1 AN an 17 Contains the name of the region within a country specific to this address. Used to hold the state in US addresses. The code related to the name can be identified in the UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations. Contains the name of the city. The code related to the name can be identified in the UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations Air Waybill 1000 3039 238 3228 243 3164 241 Country M 1:1 A a2 Contains the ISO Country s ISO 3166-1/1998. UNECE Recommendation N. 3 - for the Representation of Names of Countries CODED ISO3166 US 3207 242 Country name O 0:1 AN Contains the name of the country 3206 Shipper Contact Information M 1:1 Grouping Element Shipper Contact Name O 0:1 AN Contains the Shipper contact name of the department or person. 3412 246 of Contact Numbers O 0:n Grouping Element Phone Number O 0:1 N n 25 Consignee Details M 1:1 Grouping Element Applies Consignee Internal ID O 0:1 AN Internal ID assigned to the Consignee. 3021 040 Agency d O 0:1 AN Reference identifying the Standard ID. Field is hardcoded to "EAN", "DunAndBradStreet", "UCS", etc. CODED EDIFACT 3 EAN 3039 238 Consignee Standard ID O 0:1 AN The Standard ID is used to identify the Consignee using a 3rd Party Identifier such as EAN, DUNS etc. Consignee Name And Address M 1:1 Grouping Element In case of transport of infectious substances all data Contains the Consignee's name or legal identity. In case additional names need to be specified, the different names should be separated Consignee Name M 1:1 AN an 35 3020 039 by a specific character. PO Box O 0:1 AN Contains the post office box number. 3042 239 Contains the street address. In case additional street names need to be specified, the different names should be separated by a specific Street M 1:1 AN an 35 3042 239 character. Department O 0:1 AN Contains the company department name or number. 3412 246 Zip/Postal O 0:1 AN an 9 Contains the ZIP/Postal corresponding to the street address. 3251 245 Region Name O 0:1 AN an 9 City Name M 1:1 AN an 17 Contains the name of the region within a country specific to this address. Used to hold the state in US addresses. The code related to the name can be identified in the UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations. Contains the name of the city. The code related to the name can be identified in the UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations 3228 243 3164 241 Country M 1:1 A a2 Contains the ISO Country s ISO 3166-1/1998. UNECE Recommendation N. 3 - for the Representation of Names of Countries CODED ISO3166 US 3207 242 Country name O 0:1 AN Contains the name of the country 3206 Consignee Contact Information M 1:1 Grouping Element Consignee Contact Name O 0:1 AN Contains the Consignee contact name of the department or person. of Contact Numbers O 0:n Grouping Element Phone Number O 0:1 AN n 25 In case of transport of infectious substances this element is mandatory In case of transport of infectious substances this element is mandatory of Other Party Details O 0:n Grouping Element - If more than one Party is specified a business logic should be designed to establish a sequence? Party Type M 1:1 AN Additional parties if required. Standard codes from UNEDIFACT 3035 Party function code qualifier can be used. CODED EDIFACT 3 Carrier 3035 Other Party Internal ID O 0:1 AN Internal ID assigned to the Party. 3039 Agency d O 0:1 AN Reference identifying the Standard ID. Field is hardcoded to "EAN", "DunAndBradStreet", "UCS", etc. CODED EDIFACT 3 EAN Other Party Standard ID O 0:1 AN The Standard ID is used to identify the Carrier using a 3rd Party Identifier such as EAN, DUNS etc. Other Party Name And Address M 1:1 Grouping Element Contains the name or legal identity of the Other Party. In case additional names need to be specified, the different names should be Other Party Name M 1:1 AN 3036 separated by a specific character. PO Box O 0:1 AN Contains the post office box number. 3042 239 Contains the street address. In case additional street names need to be specified, the different names should be separated by a specific Street M 1:1 AN 3042 239 character. Department O 0:1 AN Contains the company department name or number. 3412 246 Zip/Postal O 0:1 AN Contains the ZIP/Postal corresponding to the street address. 3251 245 Region Name O 0:1 AN City Name M 1:1 AN Contains the name of the region within a country specific to this address. Used to hold the state in US addresses. The code related to the name can be identified in the UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations. Contains the name of the city. The code related to the name can be identified in the UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations 3412 246 3039 238 3228 243 3164 241 Country M 1:1 A Contains the ISO Country s ISO 3166-1/1998. UNECE Recommendation N. 3 - for the Representation of Names of Countries CODED ISO3166 US 3207 242

DGP-WG/09-IP/1-4 - Functional Specifications s Country name O 0:1 AN Contains the name of the country 3206 Other Party Contact Information O 0:1 Grouping Element Other Party Contact Name O 0:1 AN Contains the Other Party contact name of the department or person. 3412 246 of Contact Numbers O 0:n Grouping Element. At least one contact number should be provided. Phone Number O 0:1 AN Dangerous Goods Emergency Contact O 0:n Grouping Element Applies Dangerous Goods Emergency Contact Name M 1:1 AN an 35 Contains the Emergency contact name (e.g. the name of the agency) 3036 153 Phone Number M 1:1 AN n 25 Transport Details O 0:1 Grouping Element Contains the code of the country of departure. UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations Departure Country M 1:1 A 3215 can be used. Departure Country Name O 0:1 AN Contains the name of the country of departure 3214 Contains the code of the country of destination. UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations Destination Country M 1:1 A 3259 can be used. Destination Country Name O 0:1 AN Contains the name of the country of destination 3258 Mode of Transport used O 0:n AN Grouping Element Sequence of the transport O 0:1 A Contains the incremental number that identifies the sequence 7168 Mode of Transport O 0:1 AN of the Mode of Transport. UNECE Recommendation N. 19 - for Modes of Transport CODED NECE Rec. 4 8067 183 Mode of Transport Name O 0:1 A Name of the Mode of Transport as mentioned in the UNECE Recommendation N. 19 - for Modes of Transport code list CODED NECE Rec. AIR 8066 Means of Transport ID O 0:1 AN Reference to the unique conveyance ID of the means of transport (e.g. flight number, voyage number) BA1234 8028 149 Means of Transport Name O 0:1 AN Name of the Mean of Transport (e.g. Vessel name) Transport equipment O 0:n AN Grouping Element Reference O 0:1 AN Contains identification number (e.g. vehicle registration number) 8260 Seal Number O 0:1 AN Contains the seal number affixed 9308 Type O 0:1 AN Describes the type of the Container or Vehicle 8155 Size O 0:1 AN Contains the size of the Container or Vehicle 8154 Reference identifying the Loading point. Field can be hardcoded to the following codes "Seaport", "Airport", "Freight Terminal", "Rail Loading Location Type O 0:1 AN HARDCODED Airport 3227 Station", "Other". name of a seaport, airport, freight terminal, rail station or other place at which goods are loaded onto the means of transport being Loading Location O 0:1 AN CODED NECE Rec. GB LHR 3335 070 used for their carriage. UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations can be used. Name of a seaport, airport, freight terminal, rail station or other place at which goods are loaded onto the means of transport being used Loading Location Name O 0:1 AN an 17 3334 069 for their carriage. Free text or UNECE Recommendation N. 16 - LOCODE can be used. Loading Date O 0:1 D Date at which goods are loaded onto the means of transport being used for their carriage. 2347 Reference identifying the Unloading point. Field can be hardcoded to the following codes "Seaport", "Airport", "Freight Terminal", "Rail Unloading Location Type O 0:1 AN HARDCODED Airport 3227 Station", "Other". name of a seaport, airport, freight terminal, rail station or other place at which goods are unloaded from the means of transport Unloading Location O 0:1 AN CODED NECE Rec. GB LHR 3393 080 having been used for their carriage. UNECE Recommendation 16 can be used. Name of a seaport, airport, freight terminal, rail station or other place at which goods are unloaded from the means of transport having Unloading Location Name O 0:1 AN an 17 3392 079 been used for their carriage. Free text or UNECE Recommendation N. 16 - LOCODE can be used. Unloading Date O 0:1 D Date at which goods are unloaded from the means of transport having been used for their carriage. 2113 Additional Information O 0:1 AN Free text such as the Transport statement Mode specific additional information Grouping Element Aircraft DG limitation O 0:1 AN Shipment DG Type O 0:1 AN Contains the Special Handling related to the prescribed limitation. Hardcoded to "PASSENGER AND CARGO AIRCRAFT" or "CARGO AIRCRAFT ONLY" Contains the Special Handling related to radioactive or non-radioactive shipment. Hardcoded to "Non-Radioactive" or "Radioactive" Compliance Declaration Text O 0:1 AN Contains the warning message complying with the regulations text note. Shipper's Declaration Text O 0:1 AN Contains the shipper's declaration to comply with the regulations text note. Free text HARDCODED HARDCODED CARGO AIRCRAF T ONLY Non- Radioacti ve Applies Applies Applies Applies Header Note O 0:1 AN Contains a message level text note. Free text 4150 105 SHIPPERS' DECLARATION FOR DG LINE ITEM DETAILS O 0:1 Grouping Element Applies of Line Item Detail M 1:n Grouping Element - Repeated per Line-Item Item Details M 1:1 Grouping Element Line-Item Number M 1:1 AN Identifies uniquely each line-item contained in the document. Dangerous Goods M 1:1 Grouping Element UN/ID number M 1:1 N A 4-numeric field that must be preceded by the letters "UN" or "ID", as applicable. UN1263 7124 Proper shipping name M 1:1 AN an 65 The name used to describe the particular article or substance as shown in the UN Model Regulations Dangerous Goods Paint Technical name O 0:1 AN Supplementary information O 0:1 AN This is additional chemical name(s) required for some proper shipping names. When added the technical must be shown in parentheses immediately following the proper shipping name. Additional information that may be added in addition to the proper shipping to more fully describe the goods or to identify a particular condition Hazard class / division M 1:1 AN Identifies the hazard class / division identification containing a numeric field separated by a decimal Waste, empty uncleaned, etc. 1.3, 2.2, 3, etc. 7254 7488 8351 Compatibility Group O 0:1 A Specifies the reference to the group which identifies the kind of substances and articles that are deemed to be compatible. Mandatory field in case of transport of explosive articles or substances Subsidiary hazard class / division O 0:1 N Packing group O 0:1 A a 3 If used must reference I, II or III RQ O 0:1 AN Reportable quantities Mode specific additional information Grouping Element Identifies the subsidiary hazard class / division identification containing a numeric field separated by a decimal. There may be 0, 1 or 2 subsidiary risk classes or divisions. If there is more than one, each should be separated by a comma. The subsidiary risk must be shown in parentheses. To and from the USA only (2.1), (3, 8), etc. 8078

- 5 - DGP-WG/09-IP/1 Functional Specifications s Flashpoint O 0:1 AN The lowest temperature at which a liquid produces enough vapor to form an ignitable mixture in air. Only applied to flammable liquids Marine Pollutant O 0:1 AN An indicator if these transported dangerous goods have a marine pollutant content. Tunnel Restriction O 0:1 AN related to the restrictions for the transport of dangerous goods in Tunnels Hazard Identification O 0:1 AN indicating the hazards of the substance transporter Applies to road transport only Applies only to Rail for Bulk 7088 SP 640 O 0:1 AN Indicates that the Special provision number 640 applies Transport Category O 0:1 AN indicating the hazards of the transport category IMDG Segregation Group O 0:1 AN IMDG Segregation Group and number Temperatures O 0:1 AN Grouping Element Control Temperature O 0:1 AN Specifies the control temperature in C 6242 Emergency Temperature O 0:1 AN Specifies the emergency temperature in C Unit of measurement M 1:1 A Quantity M 1:1 N The total quantity of dangerous goods transported of this line item. Packing Instruction number O 0:1 AN Authorisations O 0:1 AN. In case of transport of radioactive materials the units of measure to be used is Becquerel, multiples of Becquerel, Grams or multiples of Grams The packing instruction number applicable to the UN number / proper shipping name entry. A three-numeric value which may be preceded by the letter "Y". Contains additional information relating to an approval, permission or other specific detail applicable to the commodity (e.g. Dangerous Goods in excepted quantities) For air transport some kg values must be followed by the letter "G" For air transport the value must be the volume or mass in each package. Mandatory field for air transport Litre, L, ml, kilogram, kg, gram, etc. 372, Y305 LTD QTY, A2, certificate number, etc. All packed in one O 0:1 AN A statement identifying that the dangerous goods listed above are all contained in the same outer packaging. Takes the form "All packed in one aaaa (description of packaging type) x nn (number of packages)". Applies to air transport only. All packed in one fiberboard box x 3 Q" value O 0:1 AN Most instances of "all packed in one" will require the addition of the Q value which 1. Overpack O 0:1 AN Radioactive materials O 0:1 Grouping Element Radionuclide M 1:1 AN M 1:1 AN Physical and chemical form O 0:1 AN A description of the physical and chemical form of the material. Required to be shown when individual packages are assembled into a single unit for handling. The statement "Overpack used" must be inserted immediately after all of the relevant entries relating to the packages within the overpack. The name or symbol of each radionuclide or for mixtures of radionuclides, an appropriate general description, or a list of the most restrictive radionuclides. Applies to air transport only. Applies to air transport only. Q = 0.8 Special Form O 0:1 AN A notation that the material is "special form" LDM O 0:1 AN A notation that the material is "low dispersable radioactive material". Category M 1:1 A The category of the package, overpack or freight container, i.e. I-White, II-Yellow, III-Yellow. Transport Index O 0:1 AN Applies to categories II-Yellow and III-Yellow only. A numeric value expressed to one decimal place preceded by the letters "TI". TI 3.0 Criticality Safety Index O 0:1 AN Applies to fissile material only, other than fissile excepted. A numeric value expressed to one decimal place preceded by the letters "CSI". Fissile excepted O 0:1 AN Indicates if Fissile is excepted Line-Item Note O 0:1 AN Contains an item level text note. Free text SHIPPERS' DECLARATION FOR DG PACKAGING DETAIL M 1:1 Grouping Element Applies of Package Detail O 0:n Grouping Element - Repeated per unique Logistics Unit Package Details M 1:n Grouping Element Packaging Type O 0:1 AN Identifies the Logistic Unit package type. UN Recommendation on Transport of Dangerous Goods, Model Regulations 7065 141 Packaging Type M 1:1 AN an 20 Free Text. Describes the package type. 7064 Number of Packages M 1:1 AN Identifies the number of logistics unit that are being described. 7224 of Package O 0:n Grouping Element 7075 Package Item ID O 0:1 AN Logistics Unit ID. The package ID is an incremental number that identifies each logistic unit being described. 7070 006 Package ID From O 0:1 AN Logistics Unit ID. The package ID from is the first incremental number that identifies each logistic unit being described. 7070 Package ID To O 0:1 AN Logistics Unit ID. The package ID to is the last incremental number that identifies each logistic unit being described. 7070 Package Gross Weight Unit Of Measurement O 0:1 AN Package Gross Weight O 0:1 AN Package gross weight Package Net Weight Unit Of Measurement O 0:1 AN Package Net Weight O 0:1 AN Package net weight Package Volume Unit Of Measurement O 0:1 AN Package Volume O 0:1 AN Package volume Package Length Unit Of Measurement O 0:1 AN Package Length O 0:1 AN Package length Package Width Unit Of Measurement O 0:1 AN In case of transport of radioactive materials this grouping element is mandatory Sr-90, Iridium - 192 metal solid, special form CSI 12 CODED NECE Rec 20 6022 6026 6028 6096 6098

DGP-WG/09-IP/1-6 - Functional Specifications s Package Width O 0:1 AN Package width Package Height Unit Of Measurement O 0:1 AN CODED NECE Rec 20 Package Height O 0:1 AN Package height Line Item Reference Number O 0:n Grouping Element Dangerous Goods Line-Item Reference Number O 0:1 AN Logistics Unit Purchasing. Reference to the Packing list Line-Item Number. 1082 144 Sub-Package Detail O 0:n Grouping Element - Repeated once per unique Base Unit when purchasing is not done by Logistic Unit. Base Unit Package Type M 1:1 AN This identifies the lowest level package type. UNECE Recommendation N. 21 - s for Passengers, Types of Cargo, Packages and Packaging Materials can be used Base Unit Package Type O 0:1 AN Free Text. Describes the lowest level package type. 7064 Number of Base Units M 1:1 AN Identifies the number of base units per logistic unit. 7224 144 of Sub-Packages/Units M 1:n Grouping Element 7075 Package Item ID O 0:1 AN Base Unit ID. The package ID is an incremental number that identifies each base unit. 7070 006 Package ID From O 0:1 AN Logistics Unit ID. The package ID from is the first incremental number that identifies each logistic unit being described. 7070 Package ID To O 0:1 AN Logistics Unit ID. The package ID to is the last incremental number that identifies each logistic unit being described. 7070 Package Gross Weight Unit Of Measurement O 0:1 AN Indicates the Unit of Measure from the. (UNECE Rec 20 Annex I) 6022 Package Gross Weight O 0:1 AN Package gross weight Package Net Weight Unit Of Measurement O 0:1 AN Package Net Weight O 0:1 AN Package net weight Package Volume Unit Of Measurement O 0:1 AN Package Volume O 0:1 AN Package volume Package Length Unit Of Measurement O 0:1 AN Package Length O 0:1 AN Package length Package Width Unit Of Measurement O 0:1 AN Package Width O 0:1 AN Package width Package Height Unit Of Measurement O 0:1 AN Package Height O 0:1 AN Package height Line Item Reference Number O 0:n Grouping Element Dangerous Goods Line-Item Reference O 0:1 AN Logistics Unit Purchasing. Reference to the Packing list Line-Item Number. 1082 ADDITIONAL HANDLING INFORMATION M 1:1 Grouping Element Other information O 0:1 AN Exclusive use shipment O 0:1 AN Indicates an exclusive use shipment SHIPPERS' DECLARATION FOR DG SUMMARY M 1:1 Grouping Element Free text. This may include items such as "Control temperature" for substances stabilized by temperature control, name and telephone number of a responsible person for infectious substances. 7065 141 Control temperature: 35 C, Responsible person: Dr. I. Brown, Tel: + 1 514 123 4567 Total Tare Unit Of Measurement O 0:1 AN 6156 Applies Total Tare Weight O 0:1 AN Contains the tare weight of the equipment Applies Total Gross Weight including Tare Unit Of Measurement O 0:1 AN 6012 131 Applies Total Gross including Tare Weight O 0:1 AN Total gross weight including the tare weight of the equipment Declaration Details O 0:1 Grouping Element Consignor Declaration M 1:1 AN Grouping Element Consignor Name M 1:1 AN Name of the Consignor 3336 Consignor Declaration Date M 1:1 D Date upon which the certification is made 2179 Consignor Declaration Place M 1:1 AN Place upon which the certification is made 3410 Consignor Declaration Text M 1:1 AN Contains the certification information. Free text. 4426 104 Consignor Declaration signature M 1:1 AN Contains the authentication of the Consignor 4427 Container/Vehicle Packing Certificate O 0:1 Grouping Element Declarant Company Name O 0:1 AN Name of the company of the declarant 3036 Declarant Name M 1:1 AN Name of the declarant 3036 Declarant Titel/Status O 0:1 AN Title or status of the declarant Declarant Declaration Date M 1:1 D Date upon which the certification is made 2001 Declarant Declaration Place Name O 0:1 AN Name of the Place on which the certification is made. The code related to the name can be identified in the UNECE Recommendation N. 16 - LOCODE - for Trade and Transport Locations. Declarant Declaration Text M 1:1 AN Contains the certification information complying with the Regulations 4426 104 Declarant Signature M 1:1 AN Contains the authentication of the Declarant 4427 Driver Information O 0:1 Grouping Element Driver Name O 0:1 AN Name of the Driver 3036 Driver reference O 0:1 AN Contains a reference number of the driver (e.g. vehicle registration number) 1153 Driver signature O 0:1 AN Contains the authentication of the Driver 4427 104 Driver Declaration Date O 0:1 D Date upon which the declaration is made 2001 Summary Note O 0:1 AN Contains a summary level text note as free text. Free text 4150 105 6008 6026 6028 6096 6098 6008 3410