SECTION E Ceiling Systems. Contents. Introduction. Design Considerations. Installation. Components. System Specifications. Floor/Ceiling Systems

SECTION E Ceiling Systems. Contents. SUBJECT Introduction Design Considerations Installation Components PAGE E2 E2 E4 E4 System Specifications Floor/Ceiling Systems Roof/Ceiling Systems E6 E12 Floor or Ceiling Systems - Fire Rated from Above E16 Ceiling Systems - Fire Rated from Above and/or Below E17 Panel Ceiling Systems System Installation Details E18 E19 E1. The Red Book

Introduction. CSR Gyprock and Fibre Cement (GFC) has developed a wide range of floor/ceiling and roof/ceiling systems to meet specific fire and acoustic requirements. The systems include ratings for sound transmission, sound impact and sound absorption, and for fire resistance up to. Generally, the fire resistance of floor and roof/ceiling systems is assessed from below, in accordance with the standard fire test of AS1530.4. This is the requirement of the BCA where lightweight construction is used for compartmentation and separation. Some elements such as fire-isolated passageways are required to have an when tested from outside. A number of ceiling systems are available that offer fire resistance from above to meet this requirement. CSR GFC ceiling systems use various fixing techniques for the attachment of linings. These include: a) Direct fixing to timber and steel joists or truss bottom chords. b) Screw fixing to steel furring channels that are attached to joists. c) Screw fixing to resilient or resiliently mounted furring channels. d) Screw fixing to suspended concealed metal grid. e) Lay-in panels in suspended exposed metal grid. Design Considerations. STRUCTURAL. All floor, roof and ceiling framing must be designed for the applied loads. Guidance for the selection of Rondo suspension and grid components is given in brochure GYP570 Gyprock Ceiling Systems Installation Guide. For other elements, refer to the appropriate design standards or handbooks, or contact the manufacturer for design information. CSR GFC recommends a minimum design pressure of 0.25kPa (downward) for the ceiling framing. Other wind pressures may be applicable; the designer should refer to AS/NZS1170. Wind loads on external ceilings can be similar to those on adjacent walls. Pressures can be positive or negative and the lining, grid and structure should be designed to resist the loads. Internal suspension components, even with down struts, may not be suitable. The maximum spacing of ceiling framing is 600mm. Closer spacing may be required for some lining materials or for design loads greater than 0.5kPa. CSR GFC Ceiling systems have been designed for timber or steel framing as noted in the system specification. Timber framing shall be solid timber or engineered floor joist such as LVL Glulam, plyweb joists, or trusses made from solid timber framing must be designed in accordance with AS1720.1. or AS1684 Steel framing for direct fixing of linings shall have base metal thickness (BMT) 0.5-1.6mm. Framing may be trusses, top hats, C sections, furring channels, or similar members. in all cases they should be designed in accordance with AS4600. For steel components in external environments, in heavy industrial areas or coastal areas, additional coatings may be required. Refer to AS/NZS2785 for guidance Direct-Fix Framing Systems. Ceiling linings may be fixed directly to primary timber or steel framing, or to secondary members such as furring channels and battens. Timber members to which plasterboard will be fixed must comply with AS1684 Residential Timber- Framed Construction, or be designed in accordance with AS1720.1 Timber Structures: Design Methods. Steel framing to which plasterboard will be fixed must comply with AS/NZS4600, Cold Formed Steel Structures. Suspended Ceiling Systems. Ceiling suspension systems must be designed to AS/NZS2785 Suspended Ceilings Design and Installation. Ceilings in this manual are not trafficable. Trafficable systems shall be designed in accordance with AS1657 Fixed Platforms, Walkways, Stairways and Ladders. Ceilings Rated from Above. Ceiling systems with plasterboard linings on top of joists are not trafficable or intended to be used for storage. The joists should be designed for all imposed loads including construction loads where fixing of sheets is required from above. Appropriate barriers and signage should be installed to prevent access. FIRE PERFORMANCE. Gyprock fire rated ceiling systems. have been designed with fire protection that protects the framing. E2. The Red Book

This means that no consideration of steel or timber framing design need be given for the fire rating. To protect structural beams that are entirely within the ceiling space, the structural adequacy component of the ceiling system must be at least equivalent to that required by the structural member. For example, a ceiling system with provides 90/-/- for a steel beam within the ceiling. Systems are available for beams that are not entirely enclosed. Framing and Lining. Plasterboard must be screw fixed only, adhesive is not permitted. Joints in the outer layer of all systems must be set with Gyprock paper tape. As a minimum, a single coat finish may be used. For general installation information refer to FIG. E3 to F9. Detailed fixing information is provided in brochures: Gyprock Ceiling Systems Installation Guide GYP570, CSR Gyprock Shaft Systems GYP546, CSR Fibre Cement Ceiling Systems FC129, CSR Fibre Cement ExpressWall Facade System FC126 and CSR Hebel SoundFloor Design Guide, HBL751-SFS. Ceiling systems are generally shown in a horizontal orientation. The system will not be reduced if ceilings are built on a rake. The support framing, including lateral bracing, must be designed considering the slope of the ceiling. Alternative support framing members may be used where timber joists are shown without reducing the system. These members include, but are not limited to, steel, composite steel/timber joists, laminated timber joists, and trussed or plywood web joists. System specifications for minimum cavity depths and floor surface finishes relate to acoustic performance only. Caulking. To attain the specified, all perimeter gaps and penetrations must be carefully and completely filled with appropriate caulking material. In fire rated systems, to attain the stated use CSR Gyprock Fire Mastic or other tested fire rated material of equivalent or better performance. Details for fire sealing of penetrations is given in Section Z. Vermiculite plaster is not to be used as a general purpose fire rated caulking. Its use is specified in some wall/ceiling junctions; refer to Gyprock Ceiling Systems Installation Guide GYP570. Vermiculite plaster has no capacity to accommodate building movement. PERFORMANCE. Sound Transmission. Sound flanking, the effectiveness of workmanship and caulking, the presence and treatment of penetrations, and the inclusion of structural elements and bridging items, may affect the acoustic performance of ceiling systems. Refer to Section A for detailed information. Alternative structural framing systems including steel, and composite steel/timber joists, laminated timber joists, and trussed or plywood web joists may be used without reducing the system rating. The stated or implied minimum cavity depth must also be maintained. For effective control of sound in the flanking path of a floor or roof space, acoustically rated walls should continue to the underside of the floor or roof above. Alternatively, select a detail from section Z equivalent to the required Rw or Rw + Ctr performance of the wall. In non-fire rated systems, to attain the stated sound transmission performance use CSR Gyprock Wet Area Acrylic Sealant, Gyprock Fire Mastic or other tested acoustic rated material of equivalent or better performance. Sound impact performance is stated as Ln,w + CI. Note that a lower value of Ln,w + CI has a higher impact performance. Floors finished with carpet and underlay achieve better impact performance than those with hard surfaces such as floorboards and tiles. If carpet is subsequently removed (from a system that uses it in its performance value), the floor may no longer meet the BCA impact requirements. Sound Absorption. Gyprock Perforated Plasterboard, Ecophon and Celotex ceiling products, have sound absorption qualities. These products may be used to influence the reverberation time of a room in order to improve the sound quality. Product performance is expressed as NRC in accordance with ASTM C423.This is calculated as the average of four frequencies in the range 250 2000Hz. Sound absorption values vary from 0 (total reflection) and 1.00 (total absorption) NRC values can be found in system CSR 890 E3. The Red Book

Installation For detailed information on junctions with walls, access hatches, light fixtures, control joints and penetrations, refer to Section Z of this manual. Plasterboard & Fibre Cement Fixing. Ceilings may be built to achieve a particular Level of Finish as defined in AS/NZS2589.1. The Level of Finish specified can have requirements for frame alignment, jointing and back blocking methods. Lining sheets must be installed with the long edge at right angles to the direction of the framing to which they are fixed. Refer to FIG. E3 to E9 for general fixing information using fastener and fastener/adhesive fixing methods. Detailed fixing information is provided in Gyprock Residential Installation Guide, GYP547, CSR Fibre Cement Ceiling Systems FC129 and Gyprock Ceiling Systems Installation Guide, GYP570. Components. LINING & FIXING MATERIALS Refer to Section A of this manual for detailed information on Gyprock plasterboard products, CSR Fibre Cement products, adhesive and fastener specifications. Details of the performance and range of Ecophon and Celotex acoustic ceiling panels can be found in specific product manuals. Please contact CSR Gyprock for more information. Steel Grid & Suspension Components. CSR Gyprock and Fibre Cement recommends steel components manufactured by Rondo Building Services Pty Ltd. Additional information on the steel components can be obtained from the Rondo Building Services Pty Ltd, telephone 1300 367 663. GYPROCK RESILIENT MOUNT. Jointing. Refer to the Gyprock Residential Installation Guide, GYP547 for detailed jointing and finishing of ceilings lined with In multi-layer systems, jointing and finishing is required on the visible outer layer only. Expressed joints are recommended for ceilings lined with CSR Fibre Cement products. Refer to CSR Fibre Cement Ceiling Systems FC129 for more information. Gyprock Resilient Mount 24mm 4.5mm Furring Channel 129 or 308 GYPROCK Plasterboard 20mm 40mm (129) 28mm (308) Control Joints. Control joints are used to reduce the possibility of cracks forming from structural movement, thermal and moisture movement and the like. Locations for joints should be chosen by the designer with regard to building shape, structural breaks, changes of substrate, and joint appearance. Ceiling systems with plasterboard linings must have control joints at 12m maximum spacing in both directions. Ceilings lined with CSR Fibre Cement Wallboard should have joints at 3.6m in most cases. For additional information, refer to CSR Fibre Cement Ceiling Systems FC129. Top Cross Rail Resilient Mount to Top Cross Rail Clip Gyprock Screw Gyprock Resilient Mount Furring Channel Other. Sarking with mass at least 350g/m 2 is specified in some roof/ceiling systems to achieve the acoustic value. Suitable products are Bradford Thermofoil 733 and Thermotuff SS. E4. The Red Book

FIG E1. PERFORATION PATTERN. FIG E2. GYPROCK PERFORATED PLASTERBOARD SHEET. 8.2% OPEN AREA 75mm nom. 1200mm (nominal) 3600mm (nominal) 1050mm 1200mm (nominal) 450mm 150mm 450mm Overall 3600mm (nominal) TABLE E1. MAXIMUM SPAN OF PLASTERBOARD IN CEILING APPLICATIONS. GYPROCK Plasterboard Maximum Spacing of Framing Members General Applications Areas of High Humidity Thickness (mm) (mm) 6.5mm Flexible Plasterboard used in two layers 350 NA 10mm GYPROCK Plasterboard CD 6mm CSR Fibre Cement Wallboard 450 NA 10mm, AQUACHEK, IMPACTCHEK, SUPACEIL, FLAMECHEK MR 600 450 13mm plasterboard all types except Perforated 9mm CSR Fibre Cement Wallboard 600 450 13mm Perforated Sheet 600 NA 16mm FYRCHEK 600 450 NA = Not Applicable E5. The Red Book

Floor/Ceiling Systems. PKA-A029 100 x 20mm Tongue & Grooved Cypress Pine Flooring. Timber or steel Joists at 450mm centres. Minimum 190mm cavity depth. Ceiling lining as per system table, direct fixed to framing. CEILING LININGS CAVITY INFILL (Refer to Section A) Rw / Rw+Ctr (a) Nil 27/ CSR 800 Nil (b) 105 Comfortseal R2.0 GW (c) 75 Soundscreen R2.0 RW CSR 801 Plasterboard CD. (a) Nil 35/ (b) 105 Comfortseal R2.0 GW 38/ (c) 75 Soundscreen R2.0 RW 38/ CSR 802 2 x 13mm GYPROCK Plasterboard CD. (a) Nil 38/ (b) 105 Comfortseal R2.0 GW 42/ (c) 75 Soundscreen R2.0 RW 42/ CSR 803 1 x GYPROCK SUPACEIL (a) Nil 34/ (b) 105 Comfortseal R2.0 GW 37/ (c) 75 Soundscreen R2.0 RW 37/ CSR 804 2 x 10mm GYPROCK (a) Nil 38/ (b) 105 Comfortseal R2.0 GW 42/ (c) 75 Soundscreen R2.0 RW 42/ E6. The Red Book

Floor/Ceiling Systems. RISF = Resistance to Incipient Spread of Fire Floor finished bare or with carpet and underlay, as per system table. 1 x 19mm or 22mm particleboard, or timber flooring of at least 15kg/m 2. Timber or steel joists at 600mm maximum centres. Minimum 205mm cavity depth. RONDO Furring Channel at 600mm maximum centres, (except where noted). Ceiling lining as per system table, fixed to furring channel. PKA-A029 30/30/30 +RISF 30 minutes +RISF 30 minutes FCO 964 CSR 810 CSR 811 CSR 812 CSR 813 CSR 815 CSR 814 CSR 816 CSR 819 CSR 817 CSR 818 CEILING LININGS 1 x 10mm GYPROCK SUPACEIL Plasterboard CD. 1 x 6mm CSR Fibre Cement Wallboard. (Furring at 450mm centres) 1 x 9mm CSR Fibre Cement Wallboard. 2 x 13mm GYPROCK FYRCHEK (against frame). 3 x 16mm GYPROCK CAVITY INFILL (Refer to Section A) Bare Carpet + Floor Underlay Rw / Rw+Ctr Ln,w+CI/Ln,w Ln,w+CI/Ln,w (a) Nil 38/29 81/78 66/63 (b) 105 Comfortseal R2.0 GW 43/34 79/76 61/58 (c) 75 Soundscreen R2.0 RW 43/34 79/76 61/58 (a) Nil 39/30 80/77 65/62 (b) 105 Comfortseal R2.0 GW 44/35 78/75 60/57 (c) 75 Soundscreen R2.0 RW 44/35 78/75 60/57 (a) Nil 39/30 80/77 65/62 (b) 105 Comfortseal R2.0 GW 44/35 78/75 60/57 (c) 75 Soundscreen R2.0 RW 44/35 78/75 60/57 (a) Nil 41/32 79/76 64/61 (b) 105 Comfortseal R2.0 GW 46/37 77/74 59/56 (c) 75 Soundscreen R2.0 RW 46/37 77/74 59/56 (a) Nil 41/32 79/76 64/61 (b) 105 Comfortseal R2.0 GW 46/37 77/74 59/56 (c) 75 Soundscreen R2.0 RW 46/37 77/74 59/56 (a) Nil 45/30 76/73 61/58 (b) 105 Comfortseal R2.0 GW 53/46 74/71 56/53 (c) 75 Soundscreen R2.0 RW 53/46 74/71 56/53 (a) Nil 43/35 78/75 63/60 (b) 105 Comfortseal R2.0 GW 51/43 76/73 58/55 (c) 75 Soundscreen R2.0 RW 51/43 76/73 58/55 (a) Nil 46/39 75/72 60/57 (b) 105 Comfortseal R2.0 GW 54/47 73/70 55/52 (c) 75 Soundscreen R2.0 RW 54/47 73/70 55/52 (a) Nil 46/37 75/72 60/57 (b) 105 Comfortseal R2.0 GW 54/47 73/70 55/52 (c) 75 Soundscreen R2.0 RW 54/47 73/70 55/52 (a) Nil 47/41 73/70 53/50 (b) 105 Comfortseal R2.0 GW 55/49 68/65 48/45 (c) 75 Soundscreen R2.0 RW 55/49 68/65 48/45 E8. The Red Book

Floor/Ceiling Systems. RISF = Resistance to Incipient Spread of Fire Floor finished bare or with carpet and underlay, as per system table. 1 x 19mm or 22mm particleboard, or timber flooring of at least 15kg/m 2. Timber or steel joists at 600mm maximum centres. Minimum 230mm cavity depth. RONDO Furring Channel at 600mm maximum centres, clipped to Gyprock Resilient Mounts. OR RONDO Resilient Furring Channel (581) at 600mm maximum centres. Ceiling lining as per system table, fixed to furring channel. PKA-A029 30/30/30 +RISF 30 minutes FCO 964 +RISF 30 minutes CSR 821 CSR 823 CSR 824 CSR 825 CSR 826 CSR 829 CSR 822 CSR 827 CEILING LININGS Plasterboard CD. 1 x 10mm GYPROCK 2 x 10mm GYPROCK FYRCHEK (against frame). 2 x 13mm GYPROCK CAVITY INFILL (Refer to Section A) Bare Carpet + Floor Underlay Rw / Rw+Ctr Ln,w+CI/Ln,w Ln,w+CI/Ln,w (a) Nil 45/36 73/76 55/58 (b) 105 Comfortseal R2.0 GW 53/44 64/67 47/50 (c) 75 Soundscreen R2.0 RW 52/42 64/67 47/50 (a) Nil 45/37 73/76 54/57 (b) 105 Comfortseal R2.0 GW 53/45 64/67 46/49 (c) 75 Soundscreen R2.0 RW 52/43 64/67 46/49 (a) Nil 49/41 69/72 50/53 (b) 105 Comfortseal R2.0 GW 57/49 64/67 44/47 (c) 75 Soundscreen R2.0 RW 56/47 64/67 44/47 (a) Nil 46/39 72/75 53/56 (b) 105 Comfortseal R2.0 GW 52/44 63/66 45/48 (c) 75 Soundscreen R2.0 RW 51/42 63/66 45/48 (a) Nil 48/40 71/74 52/55 (b) 105 Comfortseal R2.0 GW 54/46 62/65 44/47 (c) 75 Soundscreen R2.0 RW 53/44 62/65 44/47 (a) Nil 50/42 67/70 48/51 (b) 105 Comfortseal R2.0 GW 57/50 62/65 42/45 (c) 75 Soundscreen R2.0 RW 56/48 62/65 42/45 (a) Nil 51/44 78/71 49/52 (b) 105 Comfortseal R2.0 GW 57/50 63/66 43/46 (c) 75 Soundscreen R2.0 RW 56/48 63/66 43/46 (a) Nil 51/44 67/70 48/51 (b) 105 Comfortseal R2.0 GW 57/50 62/65 42/45 (c) 75 Soundscreen R2.0 RW 56/48 62/65 42/45 E9. The Red Book

Floor/Ceiling Systems. RISF = Resistance to Incipient Spread of Fire PKA-A029 Floor finished bare or with carpet and underlay, as per system table. 1 x 19mm or 22mm particleboard, or timber flooring of at least 15kg/m 2. Timber or steel joists at 600mm maximum centres. Minimum 340mm cavity depth. RONDO Suspended Ceiling System Ceiling lining as per system table, fixed to furring channel. 30/30/30 +RISF 30 minutes FCO 964 CSR 831 CSR 833 CSR 832 CSR 834 CSR 835 CSR 836 CSR 839 CSR 837 CSR 838 CEILING LININGS Plasterboard CD. 1 x 10mm GYPROCK 2 x 13mm GYPROCK Plasterboard CD. 2 x 10mm GYPROCK FYRCHEK (against frame). 3 x 16mm GYPROCK CAVITY INFILL (Refer to Section A) Bare Carpet + Floor Underlay Rw / Rw+Ctr Ln,w+CI/Ln,w Ln,w+CI/Ln,w (a) Nil 45/37 78/75 58/55 (b) 105 Comfortseal R2.0 GW 51/43 73/70 53/50 (c) 75 Soundscreen R2.0 RW 50/41 73/70 53/50 (a) Nil 45/37 77/74 57/54 (b) 105 Comfortseal R2.0 GW 51/43 72/69 52/49 (c) 75 Soundscreen R2.0 RW 50/41 72/69 52/49 (a) Nil 48/41 76/73 57/54 (b) 105 Comfortseal R2.0 GW 54/47 72/69 52/49 (c) 75 Soundscreen R2.0 RW 53/45 72/69 52/49 (a) Nil 48/41 76/73 57/54 (b) 105 Comfortseal R2.0 GW 54/47 72/69 52/49 (c) 75 Soundscreen R2.0 RW 53/45 72/69 52/49 (a) Nil 46/38 77/74 57/54 (b) 105 Comfortseal R2.0 GW 52/44 72/69 52/49 (c) 75 Soundscreen R2.0 RW 51/42 72/69 52/49 (a) Nil 47/39 78/75 58/55 (b) 105 Comfortseal R2.0 GW 53/45 73/70 53/50 (c) 75 Soundscreen R2.0 RW 52/43 73/70 53/50 (a) Nil 50/43 76/73 57/54 (b) 105 Comfortseal R2.0 GW 56/49 72/69 52/49 (c) 75 Soundscreen R2.0 RW 55/47 72/69 52/49 (a) Nil 50/43 76/73 57/54 (b) 105 Comfortseal R2.0 GW 56/49 71/68 52/49 (c) 75 Soundscreen R2.0 RW 55/47 71/68 52/49 (a) Nil 51/45 75/72 56/53 (b) 105 Comfortseal R2.0 GW 57/51 70/67 51/48 (c) 75 Soundscreen R2.0 RW 56/49 70/67 51/48 E10. The Red Book

Floor/Ceiling Systems. RISF = Resistance to Incipient Spread of Fire PKA-A029 Floor finished bare or with carpet and underlay, as per system table. 1 x 19mm or 22mm particleboard, or timber flooring of at least 15kg/m 2. Timber or steel joists at 600mm maximum centres. Minimum 340mm cavity depth. RONDO Suspended Ceiling System with Gyprock Resilient Mounts. Ceiling lining as per system table, fixed to furring channel. 30/30/30 +RISF 30 minutes FCO 964 CSR 841 CSR 845 CSR 846 CSR 849 CSR 847 CSR 848 CEILING LININGS Plasterboard CD. FYRCHEK (against frame). 3 x 16mm GYPROCK CAVITY INFILL (Refer to Section A) Bare Carpet + Floor Underlay Rw / Rw+Ctr Ln,w+CI/Ln,w Ln,w+CI/Ln,w (a) Nil 47/39 (b) 105 Comfortseal R2.0 GW 54/47 (c) 75 Soundscreen R2.0 RW 53/35 (a) Nil 47/39 (b) 105 Comfortseal R2.0 GW 54/46 (c) 75 Soundscreen R2.0 RW 53/44 (a) Nil 47/40 71/76 47/50 (b) 105 Comfortseal R2.0 GW 54/47 62/65 42/45 (c) 75 Soundscreen R2.0 RW 53/45 62/65 42/45 (a) Nil 53/46 67/70 47/50 (b) 105 Comfortseal R2.0 GW 60/53 62/65 42/45 (c) 75 Soundscreen R2.0 RW 59/51 62/65 42/45 (a) Nil 52/45 67/70 47/50 (b) 105 Comfortseal R2.0 GW 60/53 62/65 42/45 (c) 75 Soundscreen R2.0 RW 59/51 62/65 42/45 (a) Nil 52/46 66/69 46/49 (b) 105 Comfortseal R2.0 GW 61/55 61/64 41/44 (c) 75 Soundscreen R2.0 RW 60/53 61/64 41/44 E11. The Red Book

Roof/Ceiling Systems. RISF = Resistance to Incipient Spread of Fire A pitched tiled roof with or without 350g/m 2 sarking. OR A sheetmetal roof with minimum 50mm Bradford Anticon insulation over battens. Ceiling Joists or Trusses at 600mm maximum centres. Ceiling lining as per system table, fixed to framing. PKA-A030 CEILING LININGS CAVITY INFILL (Refer to Section A) Metal Roofing Tiled Roofing Tiled Roofing with without with Anticon Sarking Sarking Rw / Rw+Ctr CSR 950 1 x 10mm GYPROCK (a) 130 Comfortseal R2.5 GW 46/37 45/39 46/40 (b) 115 Soundscreen R3.0 RW 46/37 45/39 46/40 CSR 951 2 x 10mm GYPROCK (a) 130 Comfortseal R2.5 GW 53/44 51/45 52/46 (b) 115 Soundscreen R3.0 RW 53/44 51/45 52/46 CSR 952 Plasterboard CD. (a) 130 Comfortseal R2.5 GW 45/36 42/37 45/39 (b) 115 Soundscreen R3.0 RW 45/36 42/37 45/39 FCO 964 CSR 953 CSR 870 FYRCHEK (against frame). (a) 130 Comfortseal R2.5 GW 49/40 46/41 49/43 (b) 115 Soundscreen R3.0 RW 49/40 46/41 49/43 (a) 130 Comfortseal R2.5 GW 50/41 46/42 49/43 (b) 115 Soundscreen R3.0 RW 50/41 46/42 49/43 CSR 871 (a) 130 Comfortseal R2.5 GW 51/42 47/42 49/43 (b) 115 Soundscreen R3.0 RW 51/42 47/42 49/43 CSR 955 3 x 16mm GYPROCK (a) 130 Comfortseal R2.5 GW 54/45 51/46 52/47 (b) 115 Soundscreen R3.0 RW 54/45 51/46 52/47 E12. The Red Book

Roof/Ceiling Systems. RISF = Resistance to Incipient Spread of Fire A pitched tiled roof with or without 350g/m 2 sarking. OR A sheetmetal roof with minimum 50mm Bradford Anticon insulation over battens. Ceiling Joists or Trusses at 600mm maximum centres. RONDO Furring Channel at 600mm maximum centres, (except where noted). Ceiling lining as per system table, fixed to furring channel. PKA-A030 CEILING LININGS CAVITY INFILL (Refer to Section A) Metal Roofing Tiled Roofing Tiled Roofing with without with Anticon Sarking Sarking Rw / Rw+Ctr CSR 862 1 x 10mm GYPROCK Plasterboard CD. (a) 130 Comfortseal R2.5 GW 48/38 49/39 46/40 (b) 115 Soundscreen R3.0 RW 48/38 49/39 46/40 CSR 863 1 x 10mm GYPROCK (a) 130 Comfortseal R2.5 GW 46/37 45/39 46/40 (b) 115 Soundscreen R3.0 RW 46/37 45/39 46/40 CSR 864 (a) 130 Comfortseal R2.5 GW 49/40 46/41 48/42 (b) 115 Soundscreen R3.0 RW 49/40 46/41 48/42 CSR 868 1 x 6mm CSR Fibre Cement Wallboard. (Furring at 450mm centres). (a) 130 Comfortseal R2.5 GW 46/36 42/37 44/38 (b) 115 Soundscreen R3.0 RW 46/36 42/37 44/38 +RISF 30 minutes FCO 964 CSR 874 CSR 875 FYRCHEK (against frame). (a) 130 Comfortseal R2.5 GW 44/36 41/36 43/37 (b) 115 Soundscreen R3.0 RW 44/36 41/36 43/37 (a) 130 Comfortseal R2.5 GW 55/46 51/47 54/48 (b) 115 Soundscreen R3.0 RW 55/46 51/47 54/48 CSR 876 (a) 130 Comfortseal R2.5 GW 56/47 53/47 54/48 (b) 115 Soundscreen R3.0 RW 56/47 53/47 54/48 CSR 867 3 x 16mm GYPROCK (a) 130 Comfortseal R2.5 GW 59/50 56/51 57/52 (b) 115 Soundscreen R3.0 RW 59/50 56/51 57/52 E13. The Red Book

Roof/Ceiling Systems. RISF = Resistance to Incipient Spread of Fire A pitched tiled roof with or without 350g/m 2 sarking. OR A sheetmetal roof with minimum 50mm Bradford Anticon insulation over battens. Ceiling Joists or Trusses at 600mm maximum centres. RONDO Furring Channel at 600mm maximum centres, clipped to Gyprock Resilient Mounts. Ceiling lining as per system table, fixed to furring channel. PKA-A030 CEILING LININGS CAVITY INFILL (Refer to Section A) Metal Roofing Tiled Roofing Tiled Roofing with without with Anticon Sarking Sarking Rw / Rw+Ctr CSR 851 1 x 10mm GYPROCK (a) 130 Comfortseal R2.5 GW 48/39 47/41 48/42 (b) 115 Soundscreen R3.0 RW 48/39 47/41 48/42 CSR 852 2 x 10mm GYPROCK (a) 130 Comfortseal R2.5 GW 53/44 50/44 51/45 (b) 115 Soundscreen R3.0 RW 53/44 50/44 51/45 CSR 853 (a) 130 Comfortseal R2.5 GW 51/42 48/43 50/44 (b) 115 Soundscreen R3.0 RW 51/42 48/43 50/44 +RISF 30 minutes CSR 856 (a) 130 Comfortseal R2.5 GW 46/38 43/38 45/39 (b) 115 Soundscreen R3.0 RW 46/38 43/38 45/39 FCO 964 CSR 857 FYRCHEK plasterboard (against frame). (a) 130 Comfortseal R2.5 GW 57/48 53/49 56/50 (b) 115 Soundscreen R3.0 RW 57/48 53/49 56/50 CSR 858 (a) 130 Comfortseal R2.5 GW 58/49 55/49 56/50 (b) 115 Soundscreen R3.0 RW 58/49 55/49 56/50 CSR 859 3 x 16mm GYPROCK (a) 130 Comfortseal R2.5 GW 61/52 58/53 59/54 (b) 115 Soundscreen R3.0 RW 61/52 58/53 59/54 E14. The Red Book

Roof/Ceiling Systems. RISF = Resistance to Incipient Spread of Fire Metal deck roof Bradford R1.5 Glasswool Blanket over timber or steel purlins hard under roof. RONDO Suspended Ceiling System with Gyprock Resilient Mounts. Ceiling lining as per system table, fixed to furring channel. PKA-A030 CEILING LININGS CAVITY INFILL (Refer to Section A) Rw / Rw+Ctr CSR 860 Plasterboard CD. (a) 130 Comfortseal R2.5 GW 49/44 (b) 115 Soundscreen R3.0 RW 49/44 A low slope metal roof. Timber or Steel Purlins at 1200mm maximum centres. RONDO Furring Channel at 600mm maximum centres, fixed to purlin with fixing clips (226). Ceiling lining as per system table, fixed to furring channel. PKA-A030 CEILING LININGS CAVITY INFILL (Refer to Section A) Rw / Rw+Ctr CSR 865 (a) 130 Comfortseal R2.5 GW 51/44 (b) 115 Soundscreen R3.0 RW 51/44 CSR 866 3 x 16mm GYPROCK (a) 130 Comfortseal R2.5 GW (b) 115 Soundscreen R3.0 RW Timber or steel framing to engineer s detail. CSR ExpressWall top hat framing system. Ceiling lining as per system table, fixed to framing. PKA-A030 CEILING LININGS CAVITY INFILL (Refer to Section A) Rw / Rw+Ctr CSR 869 1 x CSR ExpressPanel. (a) Nil E15. The Red Book

Floor or Ceiling Fire Rated from Above. Ceiling lining as per system table, fixed to framing. Steel framing maximum 1.6 BMT at 600mm maximum centres. Minimum cavity depth 150mm. Ceiling lining as per system table, fixed to framing. PKA-A025 from top only FAR 2358 from top only FAR 2358 from top only FAR 2358 from top only FAR 2358 from top only FAR 2358 CSR 981 CSR 982 CSR 983 CSR 986 CSR 985 CEILING LININGS CAVITY INFILL Rw / Rw+Ctr ABOVE FYRCHEK. BELOW 1 x 10mm GYPROCK Plasterboard CD. ABOVE FYRCHEK. BELOW Nil. ABOVE FYRCHEK. BELOW 1 x 10mm GYPROCK Plasterboard CD. ABOVE 3 x 13mm GYPROCK FYRCHEK. BELOW Nil. ABOVE 3 x 16mm GYPROCK FYRCHEK. BELOW Nil. (a) Nil 40/31 (b) 50 Glasswool Partition batts 44/35 (a) Nil 34/ (a) Nil 46/37 (b) 50 Glasswool Partition batts 50/41 (a) Nil 36/34 (a) Nil 36/34 HEBEL SOUNDFLOOR Refer to CSR Hebel Carpet and medium duty underlay. CSR Hebel SoundFloor, as per system table. Timber or steel joists at 600mm maximum centres. Note: Refer to CSR Hebel for design considerations. 240/240/240 from top only Refer to CSR Hebel SF001 CEILING LININGS CAVITY INFILL Rw / Rw+Ctr Ln,w+CI ABOVE 1 x CSR Hebel SoundFloor. (a) Nil 33/30 45 E16. The Red Book

Ceilings Fire Rated from Above and/or Below. Shaftwall C-H studs at 600mm maximum centres. Lining to top side as per system table, in framing. Ceiling lining as per system table, fixed to framing. PKA-A025 CEILING LININGS CAVITY INFILL (Refer to Section A) Rw / Rw+Ctr STUD DEPTH 64 102 from top only FAR 2358 CSR 987 ABOVE 1 x 25mm GYPROCK SHAFT LINER PANEL. BELOW (a) Nil 41/30 43/34 (b) 50 Glasswool Partition batts 47/36 48/39 FAR 2358 CSR 995 ABOVE 1 x 25mm GYPROCK SHAFT LINER PANEL. BELOW (a) Nil 45/35 47/39 (b) 50 Glasswool Partition batts 51/41 52/44 FAR 2358 CSR 997 ABOVE 1 x 25mm GYPROCK SHAFT LINER PANEL. BELOW 3 x 16mm GYPROCK (a) Nil 47/37 49/41 (b) 50 Glasswool Partition batts 53/43 54/46 RISF = Resistance to Incipient Spread of Fire Ceiling lining as per system table, fixed to framing. Steel framing maximum 1.6mm BMT at 600mm maximum centres. Ceiling lining as per system table, fixed to framing. PKA-A025 CEILING LININGS CAVITY INFILL (Refer to Section A) Rw / Rw+Ctr STUD DEPTH 150 FAR 2358 CSR 994 ABOVE & BELOW (a) Nil 43/35 (b) 50 Glasswool Partition batts 47/39 from below from above FAR 2358 CSR 992 ABOVE & BELOW (a) Nil 51/43 (b) 50 Glasswool Partition batts 55/47 FAR 2358 CSR 993 ABOVE BELOW 3 x 16mm GYPROCK RISF = Resistance to Incipient Spread of Fire (a) Nil 54/46 (b) 50 Glasswool Partition batts 58/50 E17. The Red Book

Panel Ceiling Systems. Rondo Duo suspended ceiling system. (Overall Depth of System as per system table). OR Plasterboard ceiling or timber battens (Ecophon Focus F only). PANEL OPTIONS EDGE OPTIONS System CSR 890 Gyprock Exposed Grid Celotex Trim Edge Ecophon Edge A Celotex Reveal Edge Ecophon Edge E Ecophon Edge D Ecophon Edge F NRC NRC NRC NRC Overall Depth of System (mm) 50 400 60 400 50 400 20 Gyprock Perforated Plasterboard 0.13 0.49* Celotex Fine Fissured 0.55 0.55 Celotex Concorde 0.6 0.60 Celotex Directional Fissured 0.60 Celotex Sand Perforated 0.55 Ecophon Focus 085 0.85 0.9 0.8 0.85 0.80 0.75 Ecophon Master 1.0 0.95 0.9 0.8 0.85 0.95 Ecophon Advantage 0.8 0.85 * With 50mm Bradford Anticon Foil face up. E18. The Red Book

FIG E3. INSTALLATION DETAIL. SINGLE LAYER ADHESIVE & NAIL/SCREW FIXING. Timber or steel framing For 1350mm width sheets, hold sheet with temporary fastener through block at every second joist until adhesive sets Adhesive Daubs NON FIRE RATED 300mm for cornice finish 150mm for set finish For Level of Finish 4 and 5, where Butt Jointing is unavoidable, joint centrally between members and back-block. 2 Nails 50 to 75mm apart or 1 screw Where permitted, Butt Joint on member (Levels of Finish 0 to 3) 200mm min. cts 200mm min. cts Nail at 150mm or screw at 200mm 230mm centres Fixing Specifications Fasteners Adhesive Location Field Sheet Width 900mm 1200mm 1350mm Recessed Joints Centreline of Sheet Butt Joints between framing Butt Joints on framing Openings Sheet Ends Refer to Section A. Gyprock Stud Adhesive Fixing & Spacing Adhesive Daubs at 230mm centres and 200mm min. from fastener points 2 daubs 4 daubs 4 daubs Nail/screw fix at each frame member 2 nails at 50 to 75mm apart or 1 screw at each frame member Joint within 50mm of centre line between framing and adhesive fix back-block Nail fix at 150mm or screw fix at 200mm centres Nail fix at 150mm or screw fix at 200mm centres. For cornice finish, fasten at 300mm cts. For set finish, fasten at 150mm centres Offset butt joints in adjoining sheets by 600mm minimum Timber or Steel Framing at 600mm centres 300mm for cornice finish 150mm for set finish Adhesive Daubs For Levels of Finish 0 to 3, Butt Joint on member and screw fix at 200mm centres For Level of Finish 4 and 5, where Butt Jointing is unavoidable, joint centrally between members, fix with laminating screws at 200mm Offset Butt Joints in 2nd layer 600mm min. in adjoining sheets and between layers 230mm 200mm min. 230mm 200mm min. FIG E4. INSTALLATION DETAIL. TWO LAYER ADHESIVE & SCREW FIXING. 200mm 300mm Temporary block Butt Joints in 1st layer may be on same member Begin 2nd layer with a full width sheet and offset recessed joint 300mm minimum between 1st and 2nd layer Begin 1st layer with a half width sheet NON FIRE RATED Fixing Specifications 1st Layer Screws Refer to Section A. 2nd Layer Fasteners Refer to Section A. Adhesive Gyprock Stud Adhesive 1st Layer Body Sheet Width 900mm 1200mm 1350mm Butt Joints on framing Sheet Ends & Openings 2nd Layer Body Sheet Width 900mm 1200mm 1350mm Recessed Joints Centreline of Sheet Butt Joints on framing Butt joints between framing Openings Sheet Ends Fixing & Spacing Screw fix to each framing member at 300mm centres 4 screws equally spaced 5 screws equally spaced 6 screws equally spaced Screw fix at 200mm centres Screw fix at 300mm centres Fixing & Spacing Adhesive Daubs at 230mm centres and 200mm min. from fastener points 2 daubs 4 daubs 4 daubs Screw fix at each frame member. Screw fix at each frame member. Screw fix at 200mm centres. Laminating screws at 200mm centres Screws at 200mm centres. For cornice finish, screw fix at 300mm cts. For set finish, screw fix at 150mm centres E19. The Red Book

FIG E5. INSTALLATION DETAIL. SINGLE LAYER SCREW FIXING. NON FIRE RATED Suspended Grid at 600mm maximum centres 300mm for cornice finish 150mm for set finish Structural support of timber, steel or concrete Practical minimum 150mm 300mm 200mm Fixing Specifications Screws Refer to Section A. Location Fixing & Spacing Recessed Screw fix to each frame Joints & at 10 to 16mm from Body sheet edges and at Sheet 300mm centres Width between. 900mm 4 screws equally spaced 1200mm 5 screws equally spaced 1350mm 6 screws equally spaced Butt Joints Joint within 50mm of between centre line between framing framing. Back-block and fix with laminating screws at 200mm centres. Butt Joints Screw fix at 200mm on framing centres Openings Screw fix at 200mm centres. Sheet Ends For cornice finish, screw fix at 300mm cts. For set finish, screw fix at 150mm centres For Level of Finish 4 and 5, where Butt Jointing is unavoidable, support plasterboard with additional framing (Refer to FIG. 13) Where permitted, Butt Joint on member and screw fix at 200mm centres (Levels of Finish 0 to 3) 200mm Offset butt joints in adjoining sheets by 600mm minimum FIG E6. INSTALLATION DETAIL. PERFORATED PLASTERBOARD SHEETS. At butt joints, screw at 200mm centres opposed 25mm GYPROCK screws at 300mm centres Framing at 600mm centres NON FIRE RATED Fixing Specifications Screws Location Recessed Joints & Body Butt Joints on framing Sheet Ends Openings Refer to Section A. Fixing & Spacing Screw fix to each frame at 10 to 16mm from sheet edges and at 300mm centres between. Screw fix at 200mm centres. Screw fix at 200mm centres Screw fix at 200mm centres. Staggered butt joints GYPROCK Perforated Plasterboard (perforations not shown) Border of standard GYPROCK plasterboard or finish with wall angle trim E20. The Red Book

FIG E7. INSTALLATION DETAIL. ONE OR TWO LAYER NAIL OR SCREW FIXING. FOR S WITH LINING ABOVE OR BELLOW FRAMING. Refer to system specifications For framing at 600mm centres, Butt Joints in 2nd layer must be centred between framing members For framing at 450mm centres, Butt Joints in 2nd layer may be on or centrally between framing members 150/200mm Butt Joints in 2nd layer must be offset 600mm minimum in adjoining sheets and between layers Perimeter track/angle required in fire rated ceiling systems (refer to Perimeter Framing & Caulking) 150mm 200mm Butt Joints in 1st layer may be on same member Begin 2nd layer with full width sheet and offset recessed joint 300mm minimum between 1st and 2nd layer 200mm Begin 1st layer with half width sheet FIRE RATED Fixing Specifications Fasteners Refer to Section A. Location Fixing & Spacing Body of Fasten to each framing Sheet member at 10 to 16mm 1st & 2nd from sheet edges and at Layer 200mm maximum centres Butt Butt Joint on framing and Joints fasten at 150mm 1st layer centres. Butt Framing at 450mm Joints spacing Butt Joint on 2nd layer framing and fasten at 150mm centres (or as detailed for 600mm frame spacing). Framing at 600mm spacing Butt Joint within 50mm of centre line between framing and fix to 1st layer with Laminating Screws at 200mm centres Openings Fasten at 150mm centres Sheet Cornice finish Fasten Ends at 200mm centres Set finish Fasten at 150mm centres Note: Single layer systems to be fixed as per 2nd layer, Butt joints between framing are to be fully back blocked and fixed with laminating screws. FIG E8. INSTALLATION DETAIL. THREE LAYER FIXING TO STEEL OR TIMBER FRAMING NAIL OR SCREW FIXING. Suspended Grid, Steel Framing or Timber Framing at 600mm maximum centres 150/200mm 1st and 2nd layer Butt Joints on framing members, offset 600mm minimum between layers Butt Joints in 3rd layer must be placed centrally between framing, offset 600mm minimum in adjoining sheets and from previous layers 150mm 200mm 150mm 200mm Fixing Specifications Fasteners Location Body of Sheet All Layers Butt Joints 1st & 2nd Layers Butt Joints 3rd layer Sheet Ends Openings FIRE RATED Refer to Section A. Fixing & Spacing Fasten to each framing member at 10 to 16mm from sheet edges and at 200mm centres Butt Joint on framing and fasten at 150mm centres. Butt Joint within 50mm of centre line between framing and fix to previous layer with Laminating Screws at 200mm centres Cornice finish, fasten at 200mm centres Set finish, fasten at 150mm centres Fasten at 150mm centres Perimeter track/angle required in fire rated ceiling systems (refer to Perimeter Framing & Caulking) Begin 1st layer with 400mm width sheet Begin 2nd layer with 800mm width sheet Begin 3rd layer with full width sheet E21. The Red Book

FIG E9. INSTALLATION DETAIL. PLASTERBOARD FIXING TO STEEL FRAMING FIRE RATED FROM ABOVE AND/OR BELOW. FIRE RATED 150mm 200mm 300mm 150mm Top Layers Fixing Specifications Fasteners Location Body of Sheet All Layers Butt Joints Sheet Ends Refer to Section A. Fixing & Spacing Fix to upper framing at 300 centres. Fix lower framing through to upper framing at 200mm centres. Fix to upper framing at 300mm centres. Fix lower framing through to upper framing at 150mm centres. Fix at 150mm centres. 150mm 200mm 150mm Bottom Layers Fixing Specifications Fasteners Refer to Section A. Location Fixing & Spacing Body of Fasten to each framing Sheet member at 10 to 16mm from sheet edges and at 200mm centres. Sheet Width 1200mm 1350mm Butt Joints Openings Sheet Ends FIRE RATED 7 fasteners equally spaced 8 fasteners equally spaced Framing at 450mm spacing Butt Joint on framing and fasten at 150mm centres. OR Framing at 600mm spacing Butt Joint within 50mm of centre line between framing. Fully backblock and fix with laminating Screws at 200mm centres. Fasten at 150mm centres Cornice finish Fasten at 200mm centres Set finish Fasten at 150mm centres SUITABLE FOR: E22. The Red Book