Die changing station, electrically driven Dies up to a weight of 200 kn Die changing system directly adapted to the press This new die changing system with special push-pull drive makes handling of dies easier and ensures time-saving and accident-free change of dies with a maximum weight of 25 tons in places difficult to access. (Higher load-bearing capacities on request) Description: The cost-effective drive system has been developed on the basis of standard die consoles and can be easily installed as it requires only little space. Thus, it is very suitable for both retrofitting and new constructions. The drive unit and the carrying console are hung in hooks provided on the press for this purpose and then locked. The die is deposited on the consoles using a crane or a forklift truck. After the die has been deposited, it can be connected to the changing station by means of a pushand-pull system. The integral chain drive system allows the user automatic die loading and positioning, just by depressing a pushbutton on a separate remote control pendant. During a die change, the press bed is free, i.e. the push-pull elements do not project over the press bed. Also the rear side of the press is completely free. This changing station is suitable for almost any press, can be easily removed and is easy to handle. Special features: Besides the reduction of non-productive set-up time, the die changing system offers further important benefits to the user: maximization of profits due to less downtime smaller production batches are possible due to shorter set-up times greater safety for man and machine safe and accident-free handling of dies with less effort, thus creating a more humanized place of work Roller and ball bars in the T-slots of the table provide for easy insertion of the die, either manually or automatically. Damage to the die causing production loss is avoided. Individual solutions including automatic die changing and integration in the press are possible. 8.18353 233
Die changing station, electrically driven Variations of the die changing station Various variants with two driven, synchronized drive consoles and with drive motor at left/right side. The length of the console, adaptor and loads are flexibly selectable. Die changing console with drive and side loading of the press. Drive console with motor mounted at the right side Load: 100 kn, length: 2500 mm. 8.18353 234
Die changing console, manually driven Low-cost alternative to an electric drive Die changing system directly adapted to the press This new die changing console with crank handle and transmission gearing makes handling of dies easier and ensures time-saving and accident-free change of dies with a maximum weight of 6 tons in places difficult to access. (Higher loads on request) Description: The cost-effective drive system has been developed on the basis of standard die changing consoles and can be easily installed as it requires only little space. Thus, it is very suitable for both retrofitting and new constructions. The drive console is hung in hooks provided on the press for this purpose and then locked. The die is deposited on the consoles using a crane or a forklift truck. After the die has been deposited, it can be connected to the push-pull docking device of the die changing console. A crank handle at the side allows the user a safe and effortless insertion and positioning of the die. During a die change, the press bed is free, i.e. the pushpull elements do not project over the press bed. Also the rear side of the press is completely free. This die changing console is suitable for almost any press, can be easily removed and is easy to handle. Special features: Besides the reduction of non-productive set-up time, the die changing system offers further important benefits to the user: maximization of profits due to less downtime smaller production batches are possible due to shorter set-up times more safety for man and machine safe and accident-free handling of dies with less effort, thus creating a more humanized place of work Roller and ball bars in the T-slots of the bed provide for easy insertion of the die, either manually or automatically. Damage to the die causing production loss is avoided. Individual solutions including automatic die change and integration in the press are possible. 251 1 Phone Phone +49 800-827-2526 (0) 2733 / 281-0 Fax Fax 636-386-8034 +49 (0) 2733 / www.hilma-usa.com 281-169 8.18354 04/2017
Die changing console, manually driven L +40 L Push-pull docking device 345,5 91 20 45 ±0,1 1,5 3 M16 Ø16 105 Press bed h Hooks When ordering, please specify the exact support height Scope of supply: 2 carrying consoles (1 pair) 4 hooks 2 supporting feet Console Support Please indicate support height (± 60 mm) Adjustable foot with ball joint (± 60 mm) 49 125 Threaded hole M 16 for eye screws (transport by forklift truck) Technical data: Length of the console: as per customer's request Support height: as per customer's request Die weight: up to 60 kn Dimensioning and further technical details in the course of the project. Crank handle can be easily moved by one hand with a die weight of 60 kn. 8.18354 04/2017 Phone Phone +49 800-827-2526 (0) 2733 / 281-0 Fax Fax 636-386-8034 +49 (0) 2733 / www.hilma-usa.com 281-169 2 252
211
This page intentionally left blank. 212
Slot/Rollblock Dimensions RH Rollblock T-Slot Rectangular Slot ASA T-slots (ASA B5.1 1949) Metric T-slots (DIN 650) T-slot size 13 / 16 1 1 / 16 1 5 / 16 1 9 / 16 22mm 28mm 36mm a*.81 1.06 1.31 1.56.87 1.11 1.42 b 1.37 1.75 2.13 2.56 1.46 1.81 2.20 h** 1.16 1.53 2.03 2.53 1.50 1.89 2.40 Rectangular slot sizes 13 17 21 25 22 28 36 a*.81 1.06 1.31 1.56.87 1.11 1.42 h** 1.16 1.53 2.03 2.53 1.50 1.89 2.40 Rollblock size 13 17 21 25 22 28 36 Dia. of roller.39.63.63.75.63.63.75 A.795 1.04 1.28 1.54.85 1.09 1.41 H 1.14 1.51 2.01 2.51 1.48 1.87 2.38 Slot tolerance a* h** +.020 -.000 +.012 -.000 213 8.0100.US