START
Click on the product area of interest below to continue.
Roof Tops Exposed Masonry Balconies Bathrooms & Wet Areas Tanks & Water Retaining Structures Planter Boxes & Pots Retaining Walls & Below Grade Podium Decks Negative Side & Damp Substrates Parging
Advantages of Liquid Applied Membranes Fast, easy and seamless application, eliminating points of moisture ingress. Highly waterproof protective barriers. Permanently flexible to accommodate structural movement. Highly durable with high chemical and abrasion resistance. Sheet Membrane Liquid Applied Membrane Importance of Standards All Crommelin waterproofing membranes are independently tested to ensure that performance meets all relevant Australian standards. AS 4858 Wet Area Membranes. AS 3740 Waterproofing of Domestic Wet Areas. (Incorporated as a requirement of the Building Code of Australia.) AS 4654 Waterproofing Membrane Systems for Exterior Use. AS 4020 Products for Use in Contact with Drinking Water. Multiple Points of Moisture Ingress Seamless Membrane Joints and Reinforceable
Substrate design must be in accordance with BCA (Building Code of Australia) requirements. Surfaces must be installed to manufacturers requirements, suitable for use and include sufficient falls to waste. Surfaces must be clean and contaminant free. Surfaces must be sound and have a light even texture. Masonry should be flush pointed and all defects in existing surfaces made good. All surfaces must be dry (unless a specific damp surface membrane is used). Damp surfaces must be primed with suitable surface primer before membrane application. Weak or dusty surfaces must be consolidated before membrane application. Install appropriate puddle flanges or similar, coving and / or sealant to all joints and junctions. Waterproofing System Choice Always ensure that chosen membrane is fit for purpose. When To Waterproof Only when surface is completely dry. Only when environmental conditions are suitable and adequate air flow is provided to assist cure. Do not waterproof in extreme climatic conditions, or if moisture is expected during the curing phase.
Waterproofing Membrane Ensure substrate is completely dry before membrane application. Membrane should only be applied as per recommended coverage rates and film builds. Do not thin membrane with anything unless it is to be used as a prime coat and recommended by the manufacturer. Apply coat 1 evenly. Do not try and achieve too thick a film build per coat, especially in the corners. Apply coat 2 at 90⁰ to coat 1, to ensure any low points are rectified. Membrane must be protected from moisture during the cure phase. Ensure that the membrane is inspected for damage prior to over coating. Conduct any pond testing to manufacturers specifications and dry surface after test. If membrane is to be back filed against, ensure that protection board or similar is installed. Inspect membrane upon completion of after trades, to ensure that any penetrations are waterproofed or any damage repaired. Always ensure sufficient airflow is provided during the cure phase.
Bathrooms & Wet Areas Shower Waterproofing Membrane Liquid Reinforcing Shower Sealer Grout Sealer Shower Waterproofing Membrane Premium synthetic rubber under tile membrane. Showers, bathrooms, kitchens, laundries, balconies, patios, walls, floors and other wet area under tile applications. Concrete, masonry, render, plaster, steel, plywood sheeting, wet area Gyprock, wet area particle board, wet area fibre cement and timber. Class III to AS 4858. High elongation. Permanently flexible. Excellent adhesion. Colour Green Coverage 2m2 / L Coats 2 Full Cure 7 days High chemical resistance. Fast drying. Recoat 2 4 hours Thinner Water Dries to keyed finish. Promotes tile adhesion. Wet Film 500 um Shelf Life 12 months
Bathrooms & Wet Areas Drainage Termination Drain Insert Shower Waterproofing Membrane Liquid Reinforcing Shower Sealer Grout Sealer Examples of Common Wet Area Waterproofing Detailing Tiles Screed Reinforcing Elastomeric Sealant Drainage Pipe Membrane Coat 2 Membrane Coat 1 Puddle Flange Wall / Floor Junction Reinforcing Screed Tiles Hobless Shower Tiles Water Stop Screed Shower Screen Track Silicone Sealant Elastomeric Sealant Membrane Coat 1 Membrane Coat 2 Reinforcing Elastomeric Sealant Membrane Coat 2 Membrane Coat 1
Bathrooms & Wet Areas Shower Waterproofing Membrane Liquid Reinforcing Shower Sealer Grout Sealer Liquid Reinforcing Fabric Fibre reinforced, synthetic rubber under tile membrane. Class III to AS 4858. Replaces fabric. Easy detailing. Dries to keyed finish. Permanently flexible. Excellent adhesion. Fast drying. Strengthens membrane. Showers, bathrooms, kitchens, laundries, balconies, patios, walls, floors and other wet area under tile applications. Concrete, masonry, render, plaster, steel, plywood sheeting, wet area Gyprock, wet area particle board, wet area fibre cement and timber. Colour Green Coverage 2m2 / L Coats 1 Full Cure 7 days Recoat 2 4 Hours Thinner Water Wet Film 500 um Shelf Life 12 months
Bathrooms & Wet Areas Shower Waterproofing Membrane Liquid Reinforcing Shower Sealer Grout Sealer Shower Sealer Biochemically modified silicate solution. Permanently waterproofs. Trafficable immediately. Increases surface strength. Seals up to 2mm cracks. Showers, bathrooms, kitchens, laundries, balconies, patios, walls, floors and all other grout installations in wet area waterproofing applications. All cementitious construction products including concrete, masonry and grout. Colour Clear Coverage 5m2 / L Coats 1 Full Cure 48 hours Reseals future cracks. Invisible protection. Fault finding. Breathable. Recoat n/a Thinner Water Wet Film n/a Shelf Life 12 months
Bathrooms & Wet Areas Shower Waterproofing Membrane Liquid Reinforcing Shower Sealer Grout Sealer Grout Sealer Water based acrylic polymer clear surface sealer. High water repellency. High stain resistance. Satin to gloss finish. Prevents water damage. Tough, durable coating. Inhibits mould growth. UV resistant. Non yellowing. Showers, bathrooms, kitchens, laundries, balconies, patios, walls, floors and all other grout installations in wet area waterproofing applications. Cementitious grout. Colour Clear Coverage 10m2 / L Coats 2 Full Cure 7 days Recoat 2 hours Thinner Water Wet Film 100 um Shelf Life 12 months
Balconies Shower Waterproofing Membrane Shower Sealer Grout Sealer Shower Waterproofing Membrane Premium synthetic rubber under tile membrane. Balconies, showers, bathrooms, kitchens, laundries, patios, walls, floors and other wet area under tile applications. Concrete, masonry, render, plaster, steel, plywood sheeting, wet area Gyprock, wet area particle board, wet area fibre cement and timber. Class III to AS 4858. High elongation. Permanently flexible. Excellent adhesion. Colour Green Coverage 2m2 / L Coats 2 Full Cure 7 days High chemical resistance. Fast drying. Recoat 2 4 hours Thinner Water Dries to keyed finish. Promotes tile adhesion. Wet Film 500 um Shelf Life 12 months
Balconies Balcony Door Sill Door sill Tiles Shower Waterproofing Membrane Shower Sealer Grout Sealer Examples of Common Balcony Waterproofing Detailing Water stop Reinforcing Flashings of Penetrations Splitter Elastomeric Sealant Membrane Coat 1 Tiles Screed Membrane Coat 2 Membrane Coat 2 Reinforcing Elastomeric Sealant Screed Membrane Coat 1
Balconies Shower Waterproofing Membrane Shower Sealer Grout Sealer Shower Sealer Biochemically modified silicate solution. Permanently waterproofs. Trafficable immediately. Increases surface strength. Seals up to 2mm cracks. Balconies, showers, bathrooms, kitchens, laundries, patios, walls, floors and all other grout installations in wet area waterproofing applications. All cementitious construction products including concrete, masonry and grout. Colour Clear Coverage 5m2 / L Coats 1 Full Cure 48 hours Reseals future cracks. Invisible protection. Fault finding. Breathable. Recoat n/a Thinner Water Wet Film n/a Shelf Life 12 months
Balconies Shower Waterproofing Membrane Shower Sealer Grout Sealer Grout Sealer Water based acrylic polymer clear surface sealer. Balconies, showers, bathrooms, kitchens, laundries, patios, walls, floors and all other grout installations in wet area waterproofing applications. Cementitious grout. High water repellency. Satin to gloss finish. Tough, durable coating. UV resistant. High stain resistance. Prevents water damage. Inhibits mould growth. Non yellowing. Colour Clear Coverage 10m2 / L Coats 2 Full Cure 7 days Recoat 2 hours Thinner Water Wet Film 100 um Shelf Life 12 months
Retaining Walls & Below Grade Blackseal Water Based Bitumen Paint Exterior Grade Waterproofer Blackseal Synthetic rubber co-polymer bitumen emulsion, for non critical applications. Permanent flexibility. High durability. High puncture resistance. High elongation. Retaining walls, planter boxes, in ground posts, planter boxes, pots and other non-exposed waterproofing applications. Note: Not suitable for use if membrane is required to be over coated or tiled over. Concrete, masonry, timber, steel, fibre cement sheet, marine plywood, wet area particle board etc. Colour Black Coverage 1.5m2 / L Coats 2 Full Cure 7 days Fast drying. Economical. Recoat 2-4 hours Thinner Water Suitable for permanent immersion. Wet Film 660 um Shelf Life 12 months
Retaining Walls & Below Grade Blackseal Water Based Bitumen Paint Exterior Grade Waterproofer Water Based Bitumen Paint Synthetic rubber co-polymer bitumen emulsion, for non critical applications. Permanent flexibility. High durability. High puncture resistance. High elongation. Retaining walls, planter boxes, in ground posts, planter boxes, pots and other non-exposed waterproofing applications. Note: Not suitable for use if membrane is required to be over coated or tiled over. Concrete, masonry, timber, steel, fibre cement sheet, marine plywood, wet area particle board etc. Colour Black Coverage 1.5m2 / L Coats 2 Full Cure 7 days Fast drying. Economical. Recoat 2-4 hours Thinner Water Suitable for permanent immersion. Wet Film 660 um Shelf Life 12 months
Retaining Walls & Below Grade Blackseal Water Based Bitumen Paint Exterior Grade Waterproofer Exterior Grade Waterproofer High performance synthetic rubber based SBR membrane for critical and non critical applications. Permanently flexible. Good crack bridging. Paintable. Trafficable (interior). High elongation. Quick drying. Suitable to tile over. Potable water safe. Retaining walls, planter boxes, in ground posts, planter boxes, pots, water tanks and other nonexposed waterproofing applications. Concrete, masonry, render, plywood, cement sheeting, steel, aluminium and most other common porous construction materials. Colour Grey Coverage 1.5m2 / L Coats 2 Full Cure 7 days Recoat 2 hours Thinner Water Wet Film 667 um Shelf Life 12 months
Retaining Walls & Below Grade Below Grade Footing Fill Blackseal Wall Water Based Bitumen Paint Exterior Grade Waterproofer Examples of Common Retaining Wall Waterproofing Detailing Reinforcing Elastomeric Sealant Vertical Slab Joints Elastomeric Sealant Reinforcing ing rod Membrane Coat 2 Membrane Coat 1 Membrane Coat 1 Membrane Coat 2
Podium Decks Shower Waterproofing Membrane Exterior Grade Waterproofer Podium decks, balconies, terraces and roof gardens. Concrete, masonry, render, plywood, cement sheeting, steel, aluminium and most other common porous construction materials. Shower Waterproofing Membrane High performance synthetic rubber based SBR membrane for below tile / topping applications. Class III to AS 4858. High elongation. Permanently flexible. Excellent adhesion. High chemical resistance. Fast drying. Dries to keyed finish. Promotes tile adhesion. Colour Green Coverage 2m2 / L Coats 2 Full Cure 7 days Recoat 2 4 hours Thinner Water Wet Film 500 um Shelf Life 12 months
Podium Decks Shower Waterproofing Membrane Exterior Grade Waterproofer Podium decks, balconies, terraces and roof gardens. Concrete, masonry, render, plywood, cement sheeting, steel, aluminium and most other common porous construction materials. Exterior Grade Waterproofer High performance synthetic rubber based SBR membrane for below tile / topping applications. Colour Grey Coverage 1.5m2 / L Permanently flexible. Good crack bridging. Paintable. High elongation. Quick drying. Suitable to tile over. Coats 2 Full Cure 7 days Recoat 2 hours Thinner Water Wet Film 667 um Shelf Life 12 months
Roof Tops Membryl Concrete roof areas, concrete structures, exterior walls, masonry, metal and steel roofing and interior walls. Membryl Premium high build acrylic membrane with superior long term UV durability for exposed roof tops. Concrete, masonry, render, plywood, cement sheeting, steel, aluminium and most other common porous construction materials. Colour Range Coverage 1.5m2 / L Very high adhesion. Good crack bridging. Fungal resistant. Impact resistant. Quick drying. Colour range available. Coats 2 Full Cure 48 hours Recoat 4-6 hours Thinner Water Wet Film 675 um Shelf Life 12 months
Roof Tops Membryl Roof Top Reinforcing Membrane Coat 2 Examples of Common Exposed Roof Top Waterproofing Detailing Elastomeric Sealant Membrane Coat 1 Expansion Joint Reinforcing Membrane Coat 2 Parapet Wall Reinforcing Membrane Coat 2 Membrane Coat 1 Elastomeric Sealant ing Rod Membrane Coat 1 Elastomeric Sealant
Water Retaining Structures Exterior Grade Waterproofing Blackseal Trowel On Waterproofing Pond Sealer Exterior Grade Waterproofing Premium synthetic rubber tanking membrane. Suitable for full immersion. Permanently flexible. Non exposed water storage tanks, fire tanks, rain water tanks etc. Concrete, masonry, render, steel, plywood sheeting, particle board, fibre cement and aluminium. Colour Grey Coverage 1.5m2 / L High elongation. Excellent adhesion. Coats 2 Full Cure 7 days High chemical resistance. Fast drying. Recoat 2 hours Thinner Water Crack bridging. Over coatable. Wet Film 667 um Shelf Life 12 months
Water Retaining Structures Exterior Grade Waterproofing Blackseal Trowel On Waterproofing Pond Sealer Blackseal Synthetic rubber co-polymer bitumen emulsion, for non critical tanking applications. Permanent flexibility. High durability. High puncture resistance. High elongation. Fast drying. Economical. Suitable for permanent immersion. Non exposed water retaining structures, rain water tanks etc. Note: Not suitable for use if membrane is required to be over coated or tiled over. Concrete, masonry, timber, steel, fibre cement sheet, marine plywood, wet area particle board etc. Colour Black Coverage 1.5m2 / L Coats 2 Full Cure 7 days Recoat 2-4 hours Thinner Water Wet Film 660 um Shelf Life 12 months
Water Retaining Structures Exterior Grade Waterproofing Blackseal Trowel On Waterproofing Pond Sealer Trowel on Waterproofing 2 part, flexible cementitious membrane, ideal for positive and negative side waterproofing. Permanent flexibility. High abrasion resistance. High chemical resistance. Strong adhesion. Fast drying / over coating. Crack bridging. Non toxic. Non exposed water retaining structures, rain water tanks etc. Note: Must be applied to a damp substrate, but without standing water. Concrete, masonry, render, fibre cement sheeting. Colour Grey Coverage 1m2 / 1.5kg Coats 2 Full Cure 7 14 days Recoat 16-72 hrs Thinner N/ A Wet Film 1000 um Shelf Life 12 months
Water Retaining Structures Exterior Grade Waterproofing Blackseal Trowel On Waterproofing Pond Sealer Pond Sealer - Colours Synthetic rubber SBR membrane for permanently immersed conditions. Permanent flexibility. High durability. High puncture resistance. High elongation. Fast drying. Tile and paint over. Available in black, sandstone and blue. Ponds, water features, water tanks etc. Note: Use in conjunction with Dampstop for all in ground pond applications. Concrete, masonry, timber, steel, fibre cement sheet, marine plywood, wet area particle board etc. Colour Range Coverage 1.5m2 / L Coats 2 Full Cure 7 days Recoat 2-4 hours Thinner Water Wet Film 660 um Shelf Life 12 months
Planter Boxes & Pots Water Based Bitumen Paint Planter boxes, pots, in ground posts, water tanks and other non-exposed waterproofing applications. Note: Not suitable for use if membrane is required to be over coated or tiled over. Water Based Bitumen Paint Synthetic rubber co-polymer bitumen emulsion, for non critical applications. Permanent flexibility. High durability. High puncture resistance. High elongation. Fast drying. Economical. Suitable for permanent immersion. Concrete, masonry, timber, steel, fibre cement sheet, marine plywood, wet area particle board etc. Colour Black Coverage 1.5m2 / L Coats 2 Full Cure 7 days Recoat 2-4 hours Thinner Water Wet Film 660 um Shelf Life 12 months
Exposed Masonry Brick & Render Sealer Natural Finish Sealer Exposed masonry and rendered surfaces such as exterior walls etc. Note: For vertical applications only. For floor sealing, please refer to the relevant section. Brick & Render Sealer Premium water based acrylic, weatherproofing surface coating. Clear. High water repellency. Algae resistant. Low sheen finish. Highly durable. Economical. Suitable for over coating with acrylic paints. Masonry, concrete and rendered surfaces. Colour Clear Coverage 12m2 / L Coats 2 Full Cure 7 days Recoat 30 mins Thinner Water Wet Film 100 um Shelf Life 12 months
Exposed Masonry Brick & Render Sealer Natural Finish Sealer All areas of exposed masonry and natural stone surfaces that require water repellency without effecting the final appearance of the substrate. Natural Finish Sealer Highly penetrating silane siloxane blended sealer for maximum weather protection. Clear. High water repellence. Natural finish. High penetration. Suppresses efflorescence. Highly durable. Long lasting performance. Most porous substrates including concrete, masonry, timber, natural stone, fibre cement sheet, and render. Colour Clear Coverage 6-10 m2 / L Coats 2 Full Cure 7 days Recoat 2 hours Thinner Solvent Wet Film n/a Shelf Life 12 months
Parging Exterior Grade Waterproofing Spray or paint applied to slab edges to prevent rising damp, in conjunction with installed moisture barrier. Concrete and masonry. Exterior Grade Waterproofing Premium synthetic rubber tanking membrane. Suitable for full immersion. Permanently flexible. Colour Grey Coverage 1.5m2 / L High elongation. Excellent adhesion. Coats 2 Full Cure 7 days High chemical resistance. Fast drying. Recoat 2 hours Thinner Water Crack bridging. Over coatable. Wet Film 667 um Shelf Life 12 months
Negative Side & Damp Substrates Trowel On Waterproofing Dampstop Non exposed water retaining structures, rain water tanks etc. Note: Must be applied to a damp substrate, but without standing water. Trowel on Waterproofing 2 part, flexible cementitious membrane, ideal for positive and negative side waterproofing. Permanent flexibility. High abrasion resistance. High chemical resistance. Strong adhesion. Fast drying / over coating. Crack bridging. Non toxic. Concrete, masonry, render, fibre cement sheeting. Colour Grey Coverage 1m2 / 1.5kg Coats 2 Full Cure 7 14 days Recoat 16-72 hrs Thinner N/ A Wet Film 1000 um Shelf Life 12 months
Negative Side & Damp Substrates Trowel On Waterproofing Dampstop Primer coating on damp or poor surfaces prior to membrane application, as a positive or negative side membrane or as a final floor finish. Dampstop 2 part water based epoxy for positive and negative side waterproofing and damp surface priming prior to membrane applications. Easy 1:1 mix ratio. Over coatable. Tough durable surface. Fast cure. Compatible with all Crommelin liquid membranes. Concrete, stone, masonry, timber, timber panel, metal, plaster, fibre cement sheeting, render and most other common construction materials. Colour Grey Coverage 5-7 m2 / L Coats 2 Full Cure 7 days Recoat 4-6 hours Thinner Water Wet Film 200 um Shelf Life 12 months
Porous Natural Stone Masonry Dense Natural Stone Grout Terracotta Poured Limestone Concrete & Exposed Aggregate Finish Natural/Satin/Gloss Concrete Paving
Finish Natural / Satin / Gloss
All surfaces must be clean all contaminants including dirt, dust, grease, oil, curing compounds, cement laitance, algae etc must be removed with suitable cleaner. If surface has been acid etched, acid must be neutralised before sealer is applied. All surfaces must be sound and dry When To Seal Recommended to seal in the late morning or early afternoon after substrate has released moisture. Slip Resistance Gloss or satin sealers may increase the slipperiness of the coated surface. If slip resistance is critical, do not apply a coating sealer. In grip critical situations, such as sloping surfaces or where standing water may be present, natural penetrating sealers are recommended. Slip resistance may be improved with the addition of slip resistant agents into solvent based gloss and satin sealers. Do not seal if surface or ambient temperature is too high or too low. Do not seal if rain is expected during cure time, or if humidity is too high or expected to be during initial cure phase.
Sealer Conduct surface porosity test before sealer application, by adding water droplets to the surface. If water is readily absorbed and surface darkens, the surface is open to seal. If water is not absorbed, the surface is not open to seal. A trail patch is always recommended to assess final finish and slip resistant characteristics. Apply sealer as per recommended coverage rates only. Do not over apply sealer. Only thin sealer with appropriate solvent, to assist with initial coat penetration. Always ensure sealer coats are applied in an even film. Sealed area may be subjected to light foot traffic after 24 hours. Do not expose sealed area to heavy traffic until full cure has been achieved. Do not expose sealed area to moisture until full cure has been achieved. Ensure that adequate air flow is provided to assist with the curing process.
Concrete & Exposed Aggregate Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Concrete Floor Sealer Concrete Paving Sealer Clear, high performance solvent based acrylic sealer. Gloss finish. Tough durable coating. High colour enhancement. High stain resistance. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate concrete, stencilled concrete and coloured concrete. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Gloss Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Concrete & Exposed Aggregate Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Concrete Floor Sealer Wet Look Paving Sealer Clear, high performance solvent based acrylic sealer. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate concrete, stencilled concrete and coloured concrete. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Low sheen Full Cure 7 days Low sheen finish. Tough durable coating. Coats 2 Thinner Solvent High colour enhancement. High stain resistance. Recoat 2 hours Shelf Life 12 months High water repellency.
Concrete & Exposed Aggregate Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Concrete Floor Sealer Water Based Paving Sealer Clear, high performance, water based acrylic sealer. Low sheen finish. High durability. Resists mould growth. Good stain resistance. Interior and exterior low traffic areas including patios, entertaining areas, interior floors etc. Not suitable for vehicular traffic. Concrete, exposed aggregate concrete, stencilled concrete and coloured concrete. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 10-12 m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Water Recoat 1 hour Shelf Life 12 months Good water repellency.
Concrete & Exposed Aggregate Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Concrete Floor Sealer Natural Finish Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Invisible protection. Stops efflorescence. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate concrete, stencilled concrete and coloured concrete. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months High water repellency.
Concrete & Exposed Aggregate Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Concrete Floor Sealer Pool Paving Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Non-slip for wet areas. Salt / chlorine resistant. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate concrete, stencilled concrete and coloured concrete. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 4-6 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months High water repellency.
Concrete & Exposed Aggregate Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Concrete Floor Sealer Concrete Floor Sealer Clear, economical, dust-proofer and sealer. Matt to gloss finish. Good durability. Excellent dust proofing. Good stain resistance. Interior low traffic areas including workshops, sheds and interior floors etc. Not suitable for vehicular traffic. Concrete new and old. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 15-20 m2 / L Finish Matt - Gloss Full Cure 7 days Coats 2 Thinner Water Recoat 2 hours Shelf Life 12 months Good water repellency.
Concrete Paving Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Concrete Paving Sealer Clear, high performance solvent based acrylic sealer. Gloss finish. Tough durable coating. High colour enhancement. High stain resistance. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate concrete, stencilled concrete and coloured concrete. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Gloss Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Concrete Paving Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Wet Look Paving Sealer Clear, high performance solvent based acrylic sealer. Low sheen finish. Tough durable coating. High colour enhancement. High stain resistance. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate and coloured concrete paving. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Concrete Paving Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Water Based Paving Sealer Clear, high performance, water based acrylic sealer. Low sheen finish. High durability. Resists mould growth. Good stain resistance. Good water repellency. Interior and exterior low traffic areas including patios, entertaining areas, interior floors etc. Not suitable for vehicular traffic. Concrete, exposed aggregate and coloured concrete paving. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 10-12 m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Water Recoat 1 hour Shelf Life 12 months
Concrete Paving Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Natural Finish Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Invisible protection. Stops efflorescence. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate and coloured concrete paving. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Concrete Paving Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Pool Paving Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Non-slip for wet areas. Salt / chlorine resistant. High water repellency. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate concrete, stencilled concrete and coloured concrete. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 4-6 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Poured Limestone Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Concrete Paving Sealer Clear, high performance solvent based acrylic sealer. Gloss finish. Tough durable coating. High colour enhancement. High stain resistance. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Concrete, exposed aggregate concrete, stencilled concrete and coloured concrete. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Gloss Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Poured Limestone Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Wet Look Paving Sealer Clear, high performance solvent based acrylic sealer. Low sheen finish. Tough durable coating. High colour enhancement. High stain resistance. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Poured limestone, concrete and coloured concrete. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Poured Limestone Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Water Based Paving Sealer Clear, high performance, water based acrylic sealer. Low sheen finish. High durability. Resists mould growth. Good stain resistance. Good water repellency. Interior and exterior low traffic areas including patios, entertaining areas, interior floors etc. Not suitable for vehicular traffic. Poured limestone, concrete and coloured concrete. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 10-12 m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Water Recoat 1 hour Shelf Life 12 months
Poured Limestone Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Natural Finish Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Invisible protection. Stops efflorescence. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Poured limestone, concrete and coloured concrete. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Poured Limestone Concrete Paving Sealer Wet Look Paving Sealer Water Based Paving Sealer Natural Finish Sealer Pool Paving Sealer Pool Paving Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Non-slip for wet areas. Salt / chlorine resistant. High water repellency. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Poured limestone, concrete and coloured concrete. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 4-6 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Porous Natural Stone Slate Sealer Water Based Slate Sealer Limestone & Sandstone Sealer Wet Look Paving Sealer Natural Finish Sealer Pool Paving Sealer Stain Guard Slate Sealer Clear, high performance, gloss coating sealer. Gloss finish. High durability. High colour enhancement. High stain resistance. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors, path ways etc. Slate, sandstone, limestone and other porous natural stones. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Gloss Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months High water repellency.
Porous Natural Stone Slate Sealer Water Based Slate Sealer Limestone & Sandstone Sealer Wet Look Paving Sealer Natural Finish Sealer Pool Paving Sealer Stain Guard Water Based Slate Sealer Clear, high performance, water based coating sealer. Satin to gloss finish. Good durability. Low odour. Good stain resistance. Interior and exterior low traffic areas including patios, entertaining areas, interior floors etc. Not suitable for vehicular traffic. Slate, sandstone, limestone and other porous natural stones. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 12-14m2 / L Finish Satin to Gloss Full Cure 7 days Coats 2 Thinner Water Recoat 30 Minutes Shelf Life 12 months High water repellency.
Porous Natural Stone Slate Sealer Water Based Slate Sealer Limestone & Sandstone Sealer Wet Look Paving Sealer Natural Finish Sealer Pool Paving Sealer Stain Guard Limestone & Sandstone Sealer Clear, vertical surface, water based binder and sealer. Natural finish. Excellent binding. Low odour. Resists mould growth. Vertical surfaces only, including retaining walls and garden features etc. Not suitable for vehicular traffic. Limestone, sandstone and other porous natural stones. Colour Clear Coverage 2-3m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Water Recoat 2 Hours Shelf Life 12 months High water repellency.
Porous Natural Stone Slate Sealer Water Based Slate Sealer Limestone & Sandstone Sealer Wet Look Paving Sealer Natural Finish Sealer Pool Paving Sealer Stain Guard Wet Look Paving Sealer Clear, high performance solvent based acrylic sealer.. Low sheen finish. Tough durable coating. High colour enhancement. High stain resistance. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Porous natural stone paving, cladding and feature walls. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Porous Natural Stone Slate Sealer Water Based Slate Sealer Limestone & Sandstone Sealer Wet Look Paving Sealer Natural Finish Sealer Pool Paving Sealer Stain Guard Natural Finish Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Invisible protection. Stops efflorescence. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Porous natural stone paving, cladding and feature walls. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months High water repellency.
Porous Natural Stone Slate Sealer Water Based Slate Sealer Limestone & Sandstone Sealer Wet Look Paving Sealer Natural Finish Sealer Pool Paving Sealer Stain Guard Pool Paving Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Non-slip for wet areas. Salt / chlorine resistant. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Porous natural stone paving, cladding and feature walls. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 4-6 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months High water repellency.
Porous Natural Stone Slate Sealer Water Based Slate Sealer Limestone & Sandstone Sealer Wet Look Paving Sealer Natural Finish Sealer Pool Paving Sealer Stain Guard Stain Guard Clear, premium penetrating and coating sealer. Natural/Low sheen finish. High durability. Max stain protection. Maintains breathability. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Porous natural stone paving, cladding and feature walls. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 10-30m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Water Recoat 1 hour Shelf Life 12 months High water repellency.
Dense Natural Stone Stain Guard Natural Finish Sealer Pool Paving Sealer Stain Guard Clear, premium penetrating and coating sealer. Natural/Low sheen finish. High durability. Max stain protection. Maintains breathability. High water repellency. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Dense natural stone paving, cladding and feature walls, including granite, marble and travertine etc. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 10-30m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Water Recoat 1 hour Shelf Life 12 months
Dense Natural Stone Stain Guard Natural Finish Sealer Pool Paving Sealer Natural Finish Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Invisible protection. Stops efflorescence. High water repellency. Interior and exterior high traffic areas including driveways, garages, patios, entertaining areas, interior floors and path ways etc. Dense natural stone paving, cladding and feature walls, including granite, marble and travertine etc. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 6-10 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Dense Natural Stone Stain Guard Natural Finish Sealer Pool Paving Sealer Pool Paving Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Dense natural stone paving, cladding and feature walls, including granite, marble and travertine etc. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 4-6 m2 / L Finish Natural Full Cure 7 days Non-slip for wet areas. Salt / chlorine resistant. High water repellency. Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Masonry Brick & Render Sealer Natural Finish Sealer Exposed masonry and rendered surfaces such as exterior walls etc. Note: For vertical applications only and not suitable for vehicular traffic. Brick & Render Sealer Premium water based acrylic, weatherproofing Surface coating. Clear. High water repellency. Algae resistant. Low sheen finish. Highly durable. Economical. Suitable for over coating with acrylic paints. Masonry, concrete and rendered surfaces. Colour Clear Coverage 12m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Water Recoat 30 minutes Shelf Life 12 months
Masonry Brick & Render Sealer Natural Finish Sealer All areas of exposed masonry and natural stone surfaces that require water repellancy without effecting the final appearance of the substrate. Natural Finish Sealer Highly penetrating silane siloxane blended sealer for maximum weather protection. Clear. High water repellence. Natural finish. High penetration. Suppresses efflorescence. Highly durable. Long lasting performance. Most porous substrates including concrete, masonry, timber, natural stone, fibre cement sheet, and render. Colour Clear Coverage 6-10 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Grout Grout Sealer Shower Sealer Interior and exterior, vertical and horizontal grout used in tiling applications. Not suitable for use with epoxy grout. Most common cementitious grouts. Grout Sealer High performance, water based sealer for maximum grout surface protection. Clear. High water repellence. High stain resistance. Long lasting performance. Low sheen finish. Resists mould growth. Highly durable. Colour Clear Coverage 10-12 m2 / L Finish Low sheen Full Cure 7 days Coats 2 hours Thinner Water Recoat 1 hour Shelf Life 12 months
Grout Grout Sealer Shower Sealer Interior and exterior, vertical and horizontal grout used in tiling applications. Not suitable for use with epoxy grout. Most common cementitious grouts. Shower Sealer Highly penetrating treatment to permanently waterproof cementitious grout. Clear. 100% Waterproof. Densifies substrate. Permanent performance. Natural finish. High penetration. Highly durable. Colour Clear Coverage 4-6 m2 / L Finish Natural Full Cure Immediate Coats 2 Thinner n/a Recoat n/a Shelf Life 12 months
Terracotta & Clay Paving Stain Guard Natural Finish Sealer Pool Paving Sealer Stain Guard Clear, premium penetrating and coating sealer. Natural/Low sheen finish. High durability. Max stain protection. Maintains breathability. High water repellency. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Terracotta paving, pots and features and clay paving etc. Note: Coating sealers may increase surface slipperiness. Colour Clear Coverage 10-30m2 / L Finish Low sheen Full Cure 7 days Coats 2 Thinner Water Recoat 1 hour Shelf Life 12 months
Terracotta & Clay Paving Stain Guard Natural Finish Sealer Pool Paving Sealer Natural Finish Sealer Highly penetrating silane siloxane blended sealer for maximum weather protection. Clear. High water repellence. Natural finish. High penetration. Suppresses efflorescence. Highly durable. Long lasting performance. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Terracotta paving, pots and features and clay paving etc. Colour Clear Coverage 6-10 m2 / L Finish Natural Full Cure 7 days Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Terracotta & Clay Paving Stain Guard Natural Finish Sealer Pool Paving Sealer Pool Paving Sealer Clear, high performance, highly penetrating sealer. Natural finish. High durability. Exterior high traffic areas including pool surrounds, driveways, garages, patios, entertaining areas, interior floors and path ways etc. Terracotta paving, pots and features and clay paving etc. Note: Penetrating sealers will not increase surface slipperiness. Colour Clear Coverage 4-6 m2 / L Finish Natural Full Cure 7 days Non-slip for wet areas. Salt / chlorine resistant. High water repellency. Coats 2 Thinner Solvent Recoat 2 hours Shelf Life 12 months
Admixtures /Acc. Superseal Foam Admixtures Tools Reinforcing Sealants & Bond Breakers Cleaning, Thinning & Efflorescence Removal Slip Resistance
Admixtures /Acc. Admixtures Sealants & Bond Breakers Reinforcing Cleaning, Thinning & Efflorescence Removal Tools Slip Resistance Superseal Foam Liquid dampcourse additive. Prevents movement of water up masonry walls. Forms a 100% waterproof barrier. Dampco Black & Clear Superflow Concentrated plasticiser for cement mortars. Reduces amount of water required. Increases mortar strength and durability. High Performance Bonding Agent Primer for cementitious surfaces prior to waterproofing. Promotes membrane adhesion. Reduces substrate porosity. Improves performance of cement mortars and renders.
Admixtures /Acc. Admixtures Sealants & Bond Breakers Reinforcing Cleaning, Thinning & Efflorescence Removal Tools Silicone WP Plus Premium, neutral cure with ± 25% movement capability. Sanitary grade, interior and exterior. Available in translucent, white and grey. Slip Resistance Superseal Foam Reinforcing Fabric with Bond Breaker Polyurethane Sealant & Bond Breaker Self adhesive polyester fabric tape. Easy to shape and apply. For use with Crommelin Shower Waterproofing Membrane. Permanently flexible with ±25% movement capability. High recovery rate. Excellent substrate adhesion.
Admixtures /Acc. Admixtures Sealants & Bond Breakers Reinforcing Liquid Reinforcing Fabric Fibre reinforced, synthetic rubber under tile membrane. Cleaning, Thinning & Efflorescence Removal Tools Class III to AS 4858. Replaces fabric. Permanently flexible. Excellent adhesion. Slip Resistance Superseal Foam Non-woven, rot proof, 100% polyester. Superior elongation. Increases membrane strength and puncture resistance. Reinforcing Fabric Fast drying. Dries to keyed finish. Showers, bathrooms, kitchens, laundries, balconies, patios, walls, floors and other wet area under tile applications. Concrete, masonry, render, plaster, steel, plywood sheeting, wet area Gyprock, wet area particle board, wet area fibre cement and timber.
Admixtures /Acc. Admixtures Sealants & Bond Breakers Reinforcing Cleaning, Thinning & Efflorescence Removal Tools Slip Resistance Superseal Foam Pre-treatment prior to sealing. Removes ugly masonry efflorescence and white mineral salts. Efflorescence Remover Cleaning & Thinning Solvent For use in conjunction with Crommelin solvent borne acrylic resin sealers. Assists with substrate penetration. Cleaner for application tools. Water Rinsable Degreaser General purpose cleaner, degreaser and sealer remover. Prepares surface with no need to acid etch. Safe and easy removal with water.
Admixtures /Acc. Admixtures Sealants & Bond Breakers Reinforcing Cleaning, Thinning & Efflorescence Removal Tools Slip Resistance Superseal Foam Fits directly on to 500ml Crommelin Grout Sealer and Shower Sealer bottles. Fast and accurate application. Sealer Applicator Wheel Membrane Applicator Brush Non-clog, quality synthetic filament. Optimal liquid pick up and release. Available in 75mm and 100mm. Membrane Applicator Roller Non-clog, medium nap, general purpose cover. Durable polyester construction. Optimal liquid pick up and release. Available in 230mm.
Admixtures /Acc. Admixtures Sealants & Bond Breakers Reinforcing Cleaning, Thinning & Efflorescence Removal Tools Slip Resistance Superseal Foam Engineered ceramic spheres to increase slip resistance. Formulated for use with Crommelin solvent borne acrylic resin sealers. Slip Resistant Additive Sloping and grip critical surfaces and those exposed to water, in conjunction with Crommelin solvent borne acrylic resin sealers. All applicable to Crommelin solvent borne acrylic resin sealers. Note: The use of Slip Resistant Additive may increase dirt pick up and reduce cleanability of the surface. Colour Clear Consumption Width 130um 1L Sealer 10g Weight 0.4kg / L 6L Sealer 60g Coat 1 or 2 15L Sealer 125g
Admixtures /Acc. Admixtures Sealants & Bond Breakers Reinforcing Cleaning, Thinning & Efflorescence Removal Tools Slip Resistance Superseal Foam Superseal Foam Premium, highly flexible, closed cell polyurethane foam. Provides a positive seal against dust, moisture, vibration, air and vermin. Tolerates large structural movements. Remains permanently flexible. Popular profiles: Custom orb x 0.97m. Speedeck eaves / ridges x 1.02m. Trimdeck eaves / ridges x 0.94m. 25mm x 25mm x 2m. 30mm x 30mm x 2m. 40mm x 40mm x 2m. 50mm x 25mm x 2m. 50mm x 50mm x 2m. Superseal is also available in custom design profiles, self adhesive backing and alternative grade options, to meet individual project specifications.
1800 7 Day Technical Line ITP Checklists Specifications Warrantees & Certifications On Site How To Videos
1800 7 Day Specifications On Site ITP Check Lists Warranties & Certifications How To Videos Product selection advice Preparation and application advice Specifications Problem solving Organise Crommelin site visit Tips and tricks General enquiries 1800 655 711 7 Days - Nation Wide - 7.00am to 6.00pm
1800 7 Day Specifications On Site ITP Check Lists Warranties & Certifications Short format specifications. Generic format. Task specific. Designed to assist the project quoting stage. How To Videos Long format specifications. Customer project specific. Step by step, detailed instructions. Includes, preparation, application and maintenance details etc.
1800 7 Day Specifications Northern Territory Agent - Palmerston On Site ITP Check Lists Warranties & Certifications How To Videos Nationwide on site support Queensland State service centre at Banyo Western Australia Head office at Welshpool South Australia Agent - Bowden Simply call 1800 655 711 to discuss your on site requirements. New South Wales State service centre at Rydalmere Victoria State service centre at Port Melbourne
1800 7 Day Specifications On Site ITP Check Lists Warranties & Certifications Full Instructions Waterproofing Priming Checklist Membrane Installation Checklist Substrate Prep Checklist - Waterproofing How To Videos Full Instructions Sealers Substrate Prep Checklist Sealers Installation Checklist - Sealers
1800 7 Day Specifications On Site ITP Check Lists Warranties & Certifications How To Videos Up to 20 Years Product and system warranties available.
1800 7 Day Specifications On Site ITP Check Lists Warranties & Certifications How To Videos Seal a shower. Waterproof retaining walls and planter boxes. Fix leaking gutters, roofs and flashing. Waterproof a shower. Seal and protect paving around swimming pools. Seal and protect limestone and sandstone. Seal and protect paving with a water based paving sealer. Seal and colour old and stained concrete. Seal and protect paving with wet look sealer. Enhance and protect slate floors.