TRC-FWR-51441 TINGLEY RUBBER CORPORATION Product Specification Women s Weather Fashions PVC Knee Boot Style 51441 Black/Clear / Plain Toe All products conform to Tingley general manufacturing quality standards (TRC-SOP-1.00) and the requirements itemized in their particular product specification, including those contained in any component specification or SOP listed. Certificates of compliance are required from all suppliers. 1.0 Description: This Women s Boot is an injection molded PVC kneeboot with a shiny black upper and a clear transluscent, cleated outsole molded on a rocker last with a plain toe. This over-the-sock style boot is lined with hi-loft gray felt and contains a removable insole. See figures 1, 2 and 3 below. Boot Assembly Cleated Transluscent Outsole Polyester Insole Fig. 1 Fig. 2 Fig. 3 2.0 Components: Black upper: TRC-PVC-45596 Clear outsole: TRC-PVC-45552 White Polyester Insole: TRC-INS-49061 Gray felt liner: TRC-FAB-18881 See MDRL for most recent revision. Page 1 of 8 Printed: 8/26/2013
3.0 Sizes: Women s 5-10 4.0 Physical Requirements: Boots are to conform to the individual component specifications listed in section 2.0, as well as all requirements listed below. 4.1 Mold Type: Aluminum Injection Mold, TRC # 912 - Mold is designed to provide optimum material distribution and to balance side-to-side wall thickness. 4.2 Dimensions: see appendix A for average height and length of boots, by size 4.3 Weight: see appendix A for average boot weight, by size 4.4 Gauge: see appendix B for material thickness at specific boot locations 4.5 Date Code: Date of Manufacture is required as per TRC-SOP-1.01 4.6 Insole: Each boot must contain a properly sized and mated insole of the type designated in section 2.0. Size designation follows TRC-SOP-1.02 4.7 Toe Caps: Not applicable. 4.8 Pair matching: Each pair consisting of 1 left and 1 right boot must be mated in all of the following criteria. Style Size Mold number Date of Manufacture Insole 4.9 Labeling: Each pair of boots contains the following information: 4.9.1 Outsole: Mold set designation number (in the case of multiple mold sets) Date of manufacture, by month and year Country of origin Size: (women s sizes 5-10, designated on men s sizes 3-8, respectively) 4.9.2 Toe: N/A 4.9.3 Shaft: Standard Tingley Eagle logo on outside shaft of each boot. See figures 4 and 5 below. See MDRL for most recent revision. Page 2 of 8 Printed: 8/26/2013
TINGLEY SINCE 1896 Fig. 4 Fig. 5 4.9.4 Insole: The date of manufacture including shift is located on a printed, pressure sensitive label on the right insole. See TRC-LBL-28600. 4.10 Liner: Each boot is totally lined with charcoal gray hi-loft felt. It is molded into the boot with no rips, tears or wrinkles. Lining is evenly cut at top of boot shaft. 4.11Appearance: Boots are to be clean, free from obvious defects, flash and contamination. Surfaces should be visually smooth in texture and contrast, with no evidence of foreign material or distortion. Molded surfaces must be fully formed, well defined and properly aligned, with smooth seams and neatly trimmed edges. Shafts are maintained to provide a high gloss finish. Gauge (thickness) of material in each boot must be balanced to ensure shafts remain upright in a normal freestanding position. 5.0 Special Properties or Performance Standards: N/A 6.0 Packaging: 6.1 Pair unit: Each mated pair of boots is connected with a plastic fastener strung through a prepunched hole in the hangtag. Tie length is 9 in. long (approximately 23 cm.). The fastener is attached to the beading of the left and right inner shaft panel no more than 0.5 inches (1.25 cm) below the boot tops. See figure 6 below. 6.1.1 Labeling: The hangtag front contains size, style number, description, product picture and UPC barcode along with the Tingley and satisfaction guarantee logos. The hangtag back lists product benefits and features. Printing and sizing is to conform to artwork as per TRC-LBL-49548. See figure 7 below. See MDRL for most recent revision. Page 3 of 8 Printed: 8/26/2013
Figure 6 51441.05 WOMEN S PVC KNEE BOOT SIZE 5 Front Figure 7 Back See MDRL for most recent revision. Page 4 of 8 Printed: 8/26/2013
6.2 Inks: All materials including tags, case and pallet labels must be printed with permanent water-resistant inks. 6.3 Barcodes: All printed barcodes must be electronically scannable to the degree that inventory control, retail tracking and identification are facilitated. 6.4 Outer (shipping) case: Six pairs of boots are packed into each corrugated case. Each pair is placed in a toe-to-toe L-7 pattern with overlapping shafts. A cardboard divider sheet is placed in the carton after the 2 nd and 4 th pair. The carton is then straight taped to seal. Corrugated case requirements are listed in TRC-COR-42283 6.4.1 Case Logo: The red Tingley logo, company location and date of establishment is printed on opposing major panels of the case along with the country of manufacturing origin as per TRC-PKG-7500. 6.4.2 A case label containing description, style number, count, size and UPC barcode is placed in the lower right hand corner of one of the blank panels, and stacked with the labels facing the exterior of the skid. For more information on case labels, see TRC-LBL-49502. 6.4.3 Sealing: The case is straight-taped with adhesive tape on top and bottom, as per TRC-SOP-1.16 6.5 Palletization: Thirty (30) sealed shipping cartons (outer cases) are stacked on a 4-way entry 40x48 pallet. The pallet is stretch-wrapped to encompass all case layers and the pallet. All pallets must be in compliance with all US Federal requirements. 6.5.1 Labeling: Placed in the upper right hand corner of each wrapped pallet is a pallet label indicating Tingley Rubber Corporation, style number, and description as well as barcode denoting style number/size, total product count on the pallet and pallet case count. The ship date is also recorded in the space provided. See TRC-LBL-49503. 6.5.2 Partial Pallets: Palletizing multiple SKU s on one skid is minimized. When necessary, not more than two different SKU s of the same style (product number code) are mixed on a skid. Pallet labels for each SKU are placed on the stretch wrap on the upper right hand corner of the front panel of the pallet. See MDRL for most recent revision. Page 5 of 8 Printed: 8/26/2013
Attachments: TRC-SOP-1.00 (MFG STD) TRC-PVC-45552 (Compound) TRC-PVC-45596 (Compound) TRC-SOP-1.01 (Boot Date Code) TRC-SOP-1.02 (Insole Size) TRC-LBL-28600 (I.D. label-insole) TRC-LBL-49503 (Pallet Label) TRC-SOP-1.16 (Case Taping) TRC-PKG-7500 (Outer Case Graphic) TRC-INS-49061 (Insole) TRC-COR-42283 (Outer Case) TRC-LBL-49548 (Hangtag) TRC-FAB-18881 (Gray Liner) TRC-LBL-49502 (Outer Case Label) Appendix A.: Average weight and dimensions: TRC-FWR-51441 Boot size: 5 6 7 8 9 10 Height +/- 0.1 inch: 13.81 13.84 14.25 14.09 14.38 14.38 Height +/- 0.25 cm.: 35.08 35.15 36.20 35.79 36.53 36.53 Length +/- 0.1 in.: 9.66 10.00 10.34 10.63 10.84 11.28 Length +/-0.25 cm.: 24.54 25.40 26.26 27.00 27.53 28.65 Weight: +/- 0.1 lbs. 2.99 3.29 3.13 3.45 3.76 3.79 Weight: +/- 0.05 Kg. 1.36 1.49 1.42 1.57 1.71 1.72 Mold sets 1 2 2 2 1 1 * All weights listed are per pair without inserts. See MDRL for most recent revision. Page 6 of 8 Printed: 8/26/2013
Appendix B: TRC-FWR-51441 MOLD 912 - KNEE BOOT - GAUGE SPECIFICATIONS 0.085/0.090 0.100/0.110 0.120 0.140 0.220- Background 1.250 Total 0.875 Background 1.125 Total 0.345 Total (MOLD 912 KNEE BOOT) ALL MEASUREMENTS IN INCHES 1 st color - sole membrane: 0.108 +/-.010 See MDRL for most recent revision. Page 7 of 8 Printed: 8/26/2013
Appendix C: Style 51441 UPC code information : TRC-FWR-51441 Style # & Size UPC Code 51441.05 081138514454 51441.06 081138514461 51441.07 081138514478 51441.08 081138514485 51441.09 081138514492 51441.10 081138514508 See MDRL for most recent revision. Page 8 of 8 Printed: 8/26/2013