NOVOTEST of Ukraine, founded in 2009, is a leading manufacturer in Ukraine of high quality portable instruments for non-destructive testing of materials such as concrete, metal or polymeric materials. www.novotest.biz Scientific and Technical Centre "Industrial Devices and Technologies" Ltd 5, Spasskaya street Novomoskovsk, Ukraine 51200 Phone: +38-067-593-59-77, +38-056-789-88-66, 38-067-634-01-66 Fax: +38-0562-355-880, +38-05693-587-44 Email: sales@novotest.biz Skype: novotest.ua
Portable digital hardness tester NOVOTEST T-D1 is designed for rapid non-destructive testing of hardness : metals and alloys on hardness scales: Rockwell (HRC), Brinell (HB), Vickers (HV); metals with different properties from steel (for example, non-ferrous metals, alloys, cast iron, etc.) with five additional scales for calibration; use of the scale of tensile strength (Rm) for determining the tensile strength of carbon steel products pearlitic by automatically converting from the scale of hardness Brinell (HB); Implements the rebound method. Portable Hardness Tester NOVOTEST T-D1 The advantages of dynamic hardness NOVOTEST T-D1 measuring the hardness of materials with heterogeneous, coarse-grained structure, forged products, castings, cast iron performance wide range of hardness convenience and ease of measurement minimum number of controls graphical display with backlight, battery status monitoring Limitations of dynamic hardness NOVOTEST T-D1 Measurement items weighing less than 3 kg or less thickness of 12mm is possible only when the following conditions: product must be kept tightly stoppered to the surface of the base plate weighing not less than 3 kg.
Portable UCI Hardness Tester NOVOTEST T-U1 UCI Hardness tester NOVOTEST T-U1 is designed for rapid non-destructive testing of hardness according to ASTM A956 and DIN 50156: metals and alloys on standardized CIS hardness scales: Rockwell (HRC), Brinell (HB), Vickers (HV); metals with different properties from steel (for example, non-ferrous metals, alloys, cast iron, etc.) with five additional scales for calibration; use of the scale of tensile strength (Rm) in accordance with GOST 22791-77 for determining the tensile strength of carbon steel products pearlitic by automatically converting from the scale of hardness Brinell (HB); Implements the method of ultrasonic contact impedance (UCI). The advantages of ultrasonic contact impedance hardness tester NOVOTEST T-U1 hardness measurement of any mass products with a thickness of 1mm - inaccessible to the dynamic hardness (small parts, thin-walled structures, pipes, tanks, steel sheets, articles of complex shape control of metallic coatings, etc.) small print on the product surface (mirror surfaces is possible to control necks crankshafts, knives, etc. wide range of hardness convenience and ease of measurement minimum number of controls graphical display with backlight, battery status monitoring Limitations of UCI hardness tester NOVOTEST T-U1 Limited use for the measurement of products with a coarse-grained structure (eg, iron) or weighing less than 10 grams, or less than 1 mm thick
Portable Two-In-One Combined Hardness Tester NOVOTEST T-UD2 Combined hardness tester NOVOTEST T-UD2 implements methods for rebound and ultrasonic contact impedance (UCI). The combination of both methods allows control of all metal products. The advantages of universal hardness tester NOVOTEST T-UD2: 2 removable probes: ultrasonic and dynamic there are no restrictions under the control of hardness (by weight, configuration, structure, degree of mechanical and thermal treatment, etc.) to evaluate changes in the hardness of the hardened layer depth articles and the effect of surface stress wide range of hardness convenience and ease of measurement minimum number of controls graphical display with backlight automatic recognition of sensor indication of the type connected sensor control of the battery extended temperature range (frost, down to -20 degrees Celsius LED) presence of internal memory and a communication channel with PC new, intuitive menu with tips on the buttons
Coating Thickness Gauge NOVOTEST TP-1 Nondestructive testing of all types of the coatings! Rugged, fully electronic coating thickness gauges use magnetic and eddy current principles to measure coating thickness on both ferrous and non-ferrous metals, accurately and quickly. Coating thickness gauge NOVOTEST TP-1 designed for nondestructive testing thickness of: paint and other dielectric (mastic, plastic, Teflon etc.) and plating on steel (ferrous metals); paint and other dielectric (mastic, plastic, Teflon etc.) and plating on nonferrous metals and non-ferrous alloys; thickness of the bitumen and other thick coatings on various metals and alloys; as well as relative humidity, air temperature, surface temperature, dew point temperature and difference between surface and dew point temperatures, estimate the depth of grooves and the surface roughness
Ultrasonic method for measuring the thickness Ultrasonic Thickness Gauge NOVOTEST UT-1 Thickness gauge NOVOTEST UT-1 operates on the principle of measuring the propagation time of ultrasound in the product. The pulse generator produces a high frequency electrical pulses that excite the piezoelectric transducer (Probe). At the same transducer converts electrical signals into the elastic (mechanical) vibrations - sound waves. These waves propagate from the surface to reflect the input (bottom) of the surface and re-taken and converted into an electrical signal by means of PET. The instrument calculates the thickness. Ultrasonic Thickness Gauge NOVOTEST UT-1 is designed for rapid non-destructive testing of thickness: products made of various metals, alloys and other materials; thickness of glass, plastic, composite and other products from non-metallic materials; the walls of the tanks, pipes, casing parts, sheets, overhead, transportation, and other structures, including the corroded surfaces, pitted, with scum, etc. thickness of the products during their production and operation; metal thickness for diagnostic and expert work with one-side access to the object of control
Rebar Detector and Concrete Cover Meter NOVOTEST Armaturoskop The main function of rebar detector and concrete cover meter NOVOTEST Armaturoskop Measuring the thickness of the protective layer of concrete with a certain diameter Determination of the diameter of fittings for a known protective layer Measurements of the unknown parameters of reinforcement Scan mode products Deep search for reinforcement Configuration mode for steel Rebar detector and concrete cover meter NOVOTEST Armaturoskop intended for operational monitoring of reinforced concrete products and structures for process control in the factories and building sites, surveys buildings and structures. The device measures the protective layer of concrete magnetic method in accordance with GOST 22904. Measuring the thickness of concrete cover NOVOTEST Armaturoskop allows for : Operational control of the quality of reinforced concrete products and structures magnetic method in accordance with GOST 22904 for process control in factories and construction sites, the examination of structures, buildings and structures Determination of surface areas of structures, free from the overlying valve to measure the strength of the methods: ultrasound, shock pulse, separation from the edge chipping and cleavage Measure the diameter and depth of reinforcement (depending on modification)
Ultrasonic Tester of building materials strength + Depth of cracks + Flow Detect NOVOTEST IPSM U+T+D The device allows you to control the strength and homogeneity of the concrete (GOST 17 624, Recommendations NIIZhB MDS 62-2.01), brick (GOST 17624) and other materials under the composition and surface sounding in products and designs for construction projects, the process control, inspection of buildings, structures. Allows you to control the strength of concrete of unknown composition on the characteristics of TSNIIOMTP. Has the function of determining the depth of cracks in the surface sounding. Measuring the strength and uniformity of construction materials by ultrasonic method NOVOTEST IPSM-U + T + D is for : Detection of voids, cracks and defects encountered in the production and operation of structures (for process control and inspection of facilities) Control and uniformity of concrete strength (GOST 17624, Guidelines MDS 62-2.01), brick (GOST 24332), construction and composite materials, structures, bridges and waterworks Measure the depth of cracks in the products and designs Determine the density and elastic modulus uglegrafitov and fiberglass Definitions of sound index construction ceramics and abrasives Estimates of the porosity, fracturing and anisotropy of the material Assess the degree of maturity of the concrete in a monolithic concreting visualize the presence of a signal (A-scan) the possibility of control of concrete (and other) constructions for internal defects, discontinuities. Improve the accuracy of measurement of time intervals by allowing manual selection of the moment trip meter
Ultrasonic Flow Detector NOVOTEST UD-1 Flaw Detector NOVOTEST UD-1 is designed to detect defects, such as continuity and uniformity of materials in products and welded joints, to measure the depth and position of their occurrence, thickness measurements, measurements of velocity and attenuation of ultrasonic waves (ultrasonic) in the material. Ultrasonic Flaw detector NOVOTEST UD-1 with a color display and a minimum size - this is the best choice for expert ultrasonic testing. Powerful, lightweight and portable, the ergonomic impact-resistant metal casing. The flaw detector UD-1 allows to measure the thickness of the product with great accuracy, the signal to be in the form of A-and B-scans and has all the features of the full documentation of control. Ultrasonic Flaw detector NOVOTEST UD-1 allows you to replace outdated flaw detectors, providing a modern level of comfort with flaw, the function of testing results, save the settings and control of converters, and the device is priced at analog flaw detector. Ultrasonic Flaw detector NOVOTEST UD-1 meets all requirements of the modern digital flaw detector, while having a value lower than all the existing analogues! The advantages of ultrasonic flaw NOVOTEST UD-1 Frequency range with continuously adjustable from 0.2 to 10MHz. Two independently controlled gate (A and B). Automatic or manual construction of the TCG curve (32 points). Two types of representations of signals: the detection and radio. Build and handling A, B scans. Modes: the envelope, freeze and display of the beam.
Gaussmeters (Magnetometers) NOVOTEST MF-1 Gaussmeter (magnetometer) NOVOTEST MF-1 is designed for rapid non-destructive testing: magnetic fields in the control of ferromagnetic products by MT control; levels of industrial noise; technical characteristics of equipment for magnetic particle inspection of passport data and the requirements of normative and technical documentation; the level of the remanent magnetization of products after magnetic particle inspection; Portable magnetometer (gaussmeter) NOVOTEST MF-1 is equipped with a Hall sensor to measure the magnetic induction in the following units: Gauss, Tesla, Amps / meter. The instrument used to measure the static field. Magnetometer (gaussmeter) consists of an electronic unit and various removable sensors. The device runs on two standard alkaline batteries AAA (1.5 V).
www.novotest.biz NOVOTEST's worldwide dealer network supplies and supports our products throughout the world. Please contact us for the authorized dealer in your country. If you are interested in distributing our NDT Inspection Instruments, please contact us. Russia: St. Petersburg city Novotest-Russia Phone: +7-812-962-14-81 Fax: +7-812-627-68-78 Email: sales@novotest-russia.ru Canada: Port Moody BC LineLight Trading Canada Inc Phone: 604-828-0337 Fax: 604-931-2017 Email: info@linelight.ca China: Beijing Beijing LAB Hightech Instrument Ltd 121Room, Building 15, Xueyuan Road 20 Haidian District, Beijing, China (100083) Ben Zhang Phone: 86-10-58447318 Fax: 86-10-58850811