BBA 001 Documents included under the scope of BBA s ISO 17065 UKAS accreditation Product Standard Building Systems and Kits BBA Technical Specification 001 Ceiling Products BBA Technical Specification 002 Concrete and Plaster Products BBA Technical Specification 003 Heating and Ventilation Products and BBA Technical Specification 004 Systems Finishes BBA Technical Specification 005 Floor Products BBA Technical Specification 006 High Works, Products and Systems BBA Technical Specification 007 Jointing Products, Components and BBA Technical Specification 008 Materials Masonry Products BBA Technical Specification 009 Roof and Roofing Products and Systems BBA Technical Specification 0010 Drainage and Plumbing Products and BBA Technical Specification 0011 Systems Wall and Cladding Products and Systems BBA Technical Specification 0012 Window, Door and Opening Products and BBA Technical Specification 0013 Systems Polymer Modified Bitumen Liquid Applied CUAP 01.07/05 Bridge Deck Waterproofing Kit Metal Anchors for use in Concrete Part 1: ETAG 001 Anchors in General (97/177/EC) Metal Anchors for use in Concrete Part 2: ETAG 001 Torque-controlled Expansion Anchors (97/177/EC) Metal Anchors for use in Concrete Part 3: ETAG 001 Undercut Anchors (97/177/EC) Metal Anchors for use in Concrete Part 4: ETAG 001 Deformation-Controlled Expansion Anchors (97/177/EC) Metal Anchors for use in Concrete Part 5: ETAG 001 Bonded Anchors (97/177/EC) Metal Anchors for use in Concrete Part 6: ETAG 001 Anchors for Multiple use for Non-Structural Applications (97/177/EC) Structural Sealant Glazing Systems ETAG 002 (SSGS) Part 1: Supported and Unsupported Systems (96/582/EC) Structural Sealant Glazing Systems ETAG 002 (SSGS) Part 2: Coated Aluminium Systems (96/582/EC) Structural Sealant Glazing Systems ETAG 002 (SSGS) Part 3: Systems incorporating Profiles with a Thermal Barrier (96/582/EC) International Partition Kits for use as Non ETAG 003 Load-Bearing Walls (2001/596/EC) BBA 001 (18-06-59) date 03/11/15 Page 1 of 7
External Thermal Insulation Composite ETAG 004 Systems with Rendering (2001/596/EC) Liquid Applied Roof Waterproofing Kits ETAG 005 Part 1: General (2001/596/EC) Systems of Mechanically Fastened ETAG 006 Flexible Roof Waterproofing Membranes (98/143/EC) Timber Frame Building Kits (99/455/EC) ETAG 007 Prefabricated Stair Kits in General ETAG 008 (excluding severe climatic conditions) (2001/596/EC) Non Load-Bearing Permanent Shuttering ETAG 009 Kits/Systems based on Hollow Blocks or Panels of Insulating Materials and sometimes Concrete (2001/596/EC) Self Supporting Translucent Roof Kits ETAG 010 (2001/596/EC) Light Composite Wood-Based Beams and ETAG 011 Columns (99/92/EC) Log Building Kits (99/455/EC) ETAG 012 Post-Tensioning Kits for Pre-stressing of ETAG 013 Structures (98/456/EC) Plastic Anchors for Fixing of External ETAG 014 Thermal Insulation Composite Systems with Rendering (97/463/EC) Three-Dimensional Nailing Plates ETAG 015 (97/638/EC) Panels Part 1: General (94/23/EC) Panels Part 2: Specific Aspects Relating to Self-Supporting Composite Lightweight Panels for use in Roofs (94/23/EC) Panels Part 3: Specific aspects relating to Self-Supporting Composite Lightweight Panels for use in External Walls and Claddings (94/23/EC) Panels Part 4: Specific Aspects Relating to Self-Supporting Composite Light Panels for use in Internal Walls and Ceilings (94/23/EC) Veture Kits - Prefabricated Units for ETAG 017 External Wall Insulation (2001/308/EC) Fire Protective Products Part 1: General ETAG 018 (2001/596/EC) BBA 001 (18-06-59) date 03/11/15 Page 2 of 7
Fire Protective Products Part 2: Reactive ETAG 018 Coatings for Fire Protection of Steel Elements Fire Protective Products Part 3: ETAG 018 Renderings and Rendering Kits for Fire Resisting Applications Fire Protective Products Part 4: Fire ETAG 018 Protective Board, Slab and Mat Products and Kits Pre-Fabricated Wood-Based Load-Bearing ETAG 019 Stressed Skin Panels (94/23/EC) Cold Storage Premises Kits Part 1: Cold ETAG 021 Storage Room Kits (2005/484/EC) Watertight covering kits for wet room floors ETAG 022 Part 1 and / or walls Part 1: Liquid Applied Coverings with or without wearing surface: Watertight covering kits for wet room floors ETAG 022 Part 2 and / or walls Part 2: Kits based on flexible sheets Watertight covering kits for wet room floors ETAG 022 Part 3 and / or walls Part 3: Kits based on inherently watertight boards Inverted roof insulation kits ETAG 031 Liquid applied roof waterproofing kits ETAG 033 Performance of windows and doors Part BS 6375-1: 2009 1: Classification for weathertightness and guidance on selection and specification Performance of windows and doors Part BS 6375-2: 2009 2: Classification for operation and strength characteristics and guidance on selection and specification Performance of windows and doors Part BS 6375-3: 2009 3: Classification for additional performance characteristics and guidance on selection and specification Building lime. Part 1: Definitions, BS EN 459-1: 2010 specifications and conformity criteria Specification for Masonry Units. BS EN 771-4: 2010 Autoclaved Aerated Concrete Masonry Units Specification for ancillary components for BS EN 845-1 masonry Part 1: Ties, tension straps, hangers and brackets Specification for ancillary components for BS EN 845-2 masonry Part 2: Lintels Admixtures for Concrete, Mortar and BS EN 934-2: 2009 Grout. Concrete Admixtures. Definitions, Requirements, Conformity, Marking and Labelling BBA 001 (18-06-59) date 03/11/15 Page 3 of 7
Admixtures for concrete, mortar and grout BS EN 934-3: 2009 Part 3: Admixtures for masonry mortar Definition, requirements, conformity and marking and labelling Admixtures for concrete, mortar and grout BS EN 934-5: 2007 Part 5: Admixtures for sprayed concrete Specification for Mortar for Masonry. BS EN 998-2: 2011 Masonry mortar Execution of steel structures and BS EN 1090-1:2009/AC:2010 aluminium structures - Part 1: Requirements for conformity assessment of structural components Steel castings for structural uses BS EN 10340: 2007 Road construction products BS EN 12273: 2008 (microsurfacing). specifications Part 1: Asphalt Concrete specifications Part 2: Asphalt Concrete for very thin layers specifications Part 3: Soft Asphalt specifications Part 4: Hot Rolled Asphalt specifications Part 5: Stone Mastic Asphalt specifications Part 6: Mastic Asphalt specifications Part 7: Porous Asphalt Bituminous mixtures Material specifications Part 8: Reclaimed asphalt Factory Made Mineral Wool (MW) Products. Specification Factory Made Products of Expanded Polystyrene. Specification Factory Made Products of Extruded Polystyrene Foam (XPS). Specification Factory Made Rigid Polyurethane Foam (PUR) Products. Specification Factory Made Products of Phenolic Foam (PF). Specification BS EN 13108-1:2006 BS EN 13108-2: 2006 BS EN 13108-3: 2006 BS EN 13108-4: 2006 BS EN 13108-5: 2006 BS EN 13108-6: 2006 BS EN 13108-7: 2006 BS EN 13108-8: 2005 BS EN 13162:2012 BS EN 13163:2012 BS EN 13164:2012 BS EN 13165:2012 BS EN 13166:2012 BBA 001 (18-06-59) date 03/11/15 Page 4 of 7
Factory Made Cellular Glass (CG) Products. Specification Factory Made Wood Wool (WW) Products. Specification Factory Made Products of Expanded Perlite (EPB). Specification Factory Made Wood Fibre (WF) Products. Specification Flexible sheets for waterproofing - Reinforced bitumen sheets for roof waterproofing Definitions and characteristics Bitumen and bituminous binders Framework for specifying cationic bituminous emulsions Flexible sheets for waterproofing Plastic and rubber sheets for roof waterproofing Definitions and characteristics Flexible sheets for waterproofing Plastic and rubber damp proof sheets including plastic and rubber basement tanking sheet Definitions and characteristics Flexible sheets for waterproofing Bitumen damp proof sheets including bitumen basement tanking sheets Definitions and characteristics Wood-Based Panels for use in Construction. Characteristics, Evaluation of Conformity and Marking Bitumen and bituminous binders Specification framework for polymer modified bitumens Thermal insulation products for buildings - In situ formed loose-fill mineral wool (MW) Part 1: Specification for the loose fill products before installation Timber structures Product requirements for prefabricated structural members assembled with punched metal plate fasteners Thermal insulating products for buildings In situ formed sprayed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products Part 1: Specification for the rigid foam spray system before installation BS EN 13167:2012 BS EN 13168:2012 BS EN 13169:2012 BS EN 13171:2012 BS EN 13707: 2004 BS EN 13808: 2005 BS EN 13956: 2012 BS EN 13967: 2012 BS EN 13969: 2004 BS EN 13986:2004 BS EN 14023: BS EN 14064-1: 2010 BS EN 14250: 2010 BS EN 14315-1: 2013 BBA 001 (18-06-59) date 03/11/15 Page 5 of 7
Thermal insulating products for buildings BS EN 14318-1: 2013 In situ formed dispensed rigid polyurethane (PUR) and polyisocyanurate (PIR) foam products Part 1: Specification for the rigid foam dispensed system before installation Windows and doors - Product standard, BS EN 14351-1: 2006 performance characteristics - Part 1: Windows and external pedestrian doorsets without resistance to fire and/or smoke leakage characteristics Timber Structures. Structural Laminated BS EN 14374: 2004 Veneer Lumber. Requirements Timber Structures - Connectors - EN 14545: 2009 Requirements Timber structures Dowel-type fasteners - BS EN 14592 Requirements Flexible sheets for waterproofing BS EN 14695 Reinforced bitumen sheets for waterproofing of concrete bridge decks and other trafficked areas of concrete Definitions and characteristics Thermal Insulation and lightweight fill BS EN 14933 products for civil engineering applications - Factory Made products of expanded polystyrene (EPS) -Specification Precast concrete products Beam and BS EN 15037-1: 2008 block floor systems Part 1: Beams Precast concrete products Beam-and BS EN 15037-4: 2010 block floor systems Part 4: Expanded polystyrene blocks Aluminium and Aluminium Alloys - BS EN 15088: 2005 Structural Products for Construction Works Bitumen and Bituminous binders BS EN 15322 : 2009 Framework for specifying cut back and fluxed bituminous binders Solar Collectors MCS 004 Solar Photovoltaic Panels MCS 005 Micro and Small Wind Turbines MCS 006 Heat Pumps MCS 007 Biomass MCS 008 Generic Factory Production Control MCS 010 Pitched Roof Installation Kits MCS 012 Testing and acceptance criteria MCS 011 Heat led Micro-cogeneration packages in MCS 014 dwellings CHP Electricity Lead MCS 015 Bespoke Building Integrated Photovoltaic MCS 017 Products BBA 001 (18-06-59) date 03/11/15 Page 6 of 7
Enhanced Security performance requirements for doorsets and windows in the UK. External doorsets and windows intended to offer a level of security suitable for dwellings and other buildings exposed to comparable risk PAS 24:2012 BBA 001 (18-06-59) date 03/11/15 Page 7 of 7