sylodyn NF Material Colour closed cellular polyurethane violet Standard Sylodyn range Standard dimensions on stock thickness:.5 mm with Sylomer NF 5 mm with Sylomer NF5 rolls:.5 m wide, 5. m long stripes: max..5 m wide, up to 5. m long other dimensions (also thickness), as well as stamped and molded parts on request NF NE ND Area of application compression load (depending on form factor) deflection NC Static load limit Operating load range ( plus dynamic loads) up to.5 N/mm ** up to. N/mm ** approx. %** approx. 6 %** NB Load peaks (short term, infrequent loads) up to 8. N/mm ** approx. 5 %**... load limit [N/mm ] Material properties test methods comment DB Sylodyn NF E Copyright by l -8 We reserve the right to amend the data. tensile stress at break elongation at break tear strength abrasion coefficient of friction (steel) coefficient of friction (concrete) compression set shear modulus dynamic shear modulus mechanical loss factor rebound elasticity operating temperature flammability specific volume resistance thermal conductivity further characteristic values on request * tests according to respective standards ** at form factor q= 7 N/mm 5 % N/mm 9 mm.7.7 < 5 %.8 N/mm.8 N/mm. 7 % - up to 7 C B B, C and D > Ω cm. W/[m K] DIN EN ISO 57-/5/* DIN EN ISO 57-/5/* DIN 555* DIN 556 Getzner Werkstoffe Getzner Werkstoffe EN ISO 856 DIN ISO 87* DIN ISO 87* DIN 55* DIN 55 DIN 4 EN ISO 95- DIN IEC 9 DIN 56/ minimum value minimum value minimum value load N, bottom surface dry dry 5 %, C, 7 h, minutes after unloading at load limit at load limit depending on frequency, load and amplitude (reference value) tolerance + /- % short term higher temperatures possible normal flammable passed dry All information and data is based on our current knowledge. The data can be applied for calculations and as guidelines, are subject to typical manufacturing tolerances, and are not guaranteed. We reserve the right to amend the data. Further information can be found in VDI Guidline 6 Page. Herrenau 5 676 Bürs Austria Phone +4-555-- Fax +4-555--899 info.buers@getzner.com Am Borsigturm 57 Berlin Germany Phone +49--454- Fax +49--454-5 info.berlin@getzner.com Nördliche Münchner Str. 7a 8 Grünwald Germany Phone +49-89-695- Fax +49-89-695- info.gruenwald@getzner.com Middle East Regional Office Abdul-Hameed Sharaf Str. 4 Rimawi Center - Shmeisani P.O. Box 96 Amman 96, Jordan Phone +966-56-74 Fax +966-569-75 info@geme.jo Nihon Getzner K.K. Landmark Plaza, 8F Shiba Koen -6-7, Minato-ku 5- Tokyo, Japan Phone +8--54-54 Fax +8--54-69
sylodyn NF load deflection curve full surface bearing form factor: q=6.5 mm 5 mm 7.5 mm 5 mm operating load range load limit 4 5 6 7 8 9 strip bearing form factor: q=.5 mm 5 mm 7.5 mm 5 mm operating load range load limit 4 5 6 7 8 9 point bearing form factor: q=.5.5 mm 5 mm 7.5 mm 5 mm operating load range load limit 4 5 6 7 8 9 Quasi- load deflection curve measured at a velocity of deformation of % of the thickness per second; testing between flat steel-plates; recording of the rd loading; testing at room temperature
modulus of elasticity form factor: q=6 natural frequency form factor: q=6 E-modulus [N/mm ] Hz Hz.5 mm 5 mm 7.5 mm 5 mm 5 5 5 form factor: q= form factor: q= E-modulus [N/mm ] Hz Hz.5 mm 5 mm 7.5 mm 5 mm 5 5 5 form factor: q=.5 form factor: q=.5 E-modulus [N/mm ] Hz Hz.5 mm 5 mm 7.5 mm 5 mm 5 5 5 Static modulus of elasticity as a tangent modulus taken from the load deflection curve; dynamic modulus of elasticity due to sinusoidal excitation with a velocity level of dbv re. 5-8 m/s; test according to DIN 55 Natural frequency of a single-degree-of-freedom system (SDOF system) consisting of a fixed mass and an elastic bearing consisting of Sylodyn NF based on a stiff subgrade; parameter: thickness of elastomeric bearing
vibration isolation efficiency disturbing frequency [Hz] 8 6 4-4 db/99% - db/97% - db/9% reduction of the transmitted mechanical vibrations by implementation of an elastic bearing consisting of Sylodyn NF parameter: factor of transmission in db, isolation rate in % 8 - db/69% 6 4 - db/% 5 5 5 5 4 45 5 creep behaviour relative deflection [% of thickness with unstressed assay] 5 5 5 5 % load % load increase in deformation under consistent loading parameter: permanent loading form factor: q= d m a a.,,,,, period of loading [h] dynamic E-modulus at long term loading dyn. E-modulus [N/mm ] 5 4, h, h change of dynamic modulus of elasticity under consistent loading (at Hz) parameter: load duration form factor: q= h. h permanent loading [N/mm ] 4
temperature dependency dyn. E-modulus [N/mm ] 5 4 mechanical loss factor..9.8.7.6 DMA-test (Dynamic Mechanical Analysis); tests within linear area of the load deflection curve, at low specific loads.5.4 Hz. Hz Hz. Hz. - 4 5 temperature [ C]. - 4 5 temperature [ C] frequency dependency dyn. E-modulus [N/mm ] mechanical loss factor.8.6 DMA-tests; mastercurve with a reference-temperature of C; tests within the linear area of the load deflection curve, at low specific loads.4., frequenzy [Hz]., frequency [Hz] dependency on amplitude dependency on loading velocity dyn. E-modulus [N/mm ] Hz 5 N/mm /s.5 N/mm /s.5 N/mm /s dependency on amplitude: preload at load limit; form factor: q=, thickness of material 5 mm dependency on loading velocity: form factor: q=, thickness of material 5 mm Hz... amplitude [mm] 4 5 6 7 8 9 5
Form factor The form factor is a geometric measure for the shape of an elastomeric bearing defined as the ratio of the loaded area and the area of sum of the perimeter surfaces. loaded area definition: form factor= for a rectangular shape: q= (l..length, w..width, t..thickness) loaded area perimeter surface area I w t (I+w) perimeter surface area perimeter surface area The form factor has an influence on the deflection and the load limit respectively. Elastic Sylodyn-bearings are considered as full surface bearing: form factor > 6 strip bearing: form factor between and 6 point bearing: form factor < Influence of the form factor on the deflection at the load limit for a homogeneous material reference value: form factor q= Influence of the form factor on the load limit for a homogeneous material reference value: form factor q= deviation of deflection [%] % 8% 6% 4% increase of deflection load limit [N/mm ]..4 decrease of load limit increase of load limit % % decrease of deflection.8 -%. 4 5 6 4 5 6 form factor form factor 6