SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 HERMON LABORATORIES 66 Hatachana Street (Postal Mail to P.O. Box 23) Binyamina, 3055001, ISRAEL Mr. George Shleimovich Phone: 972 4 6288 001 Email: mail@hermonlabs.com MECHANICAL Valid to: May 31, 2019 Certificate Number: 0839.04 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following environmental tests on radio, telecom, and medical devices: Test Technology: Telecommunication Equipment Environmental Conditions and Environmental Tests for Telecommunications Equipment Generic Standards Guidance for the Correlation and Transformation of Environmental Condition Classes of IEC 60721-3 to the Environmental Tests of IEC 60068 ETSI EN 300 019-2-0 V2.1.2 (2003-09); ETSI EN 300 019-2-1 V2.1.2 (2000-09); ETSI EN 300 019-2-1; ETSI EN 300 019-2-2 V2.1.2 (1999-09); ETSI EN 300 019-2-2; ETSI EN 300 019-2-3 V2.2.2 (2003-04); ETSI EN 300 019-2-3; ETSI EN 300 019-2-4 V2.2.2 (2003-04); ETSI EN 300 019-2-4; ETSI EN 300 019-2-5 V3.0.0 (2002-12); ETSI EN 300 019-2-6 V3.0.0 (2002-12); ETSI EN 300 019-2-7 V3.0.1 (2003-04); ETSI EN 300 019-2-8 V2.1.2 (1999-09) IEC 60721-4-1; IEC 60721-4-2; IEC 60721-4-3; IEC 60721-4-4; IEC 60721-4-5; IEC 60721-4-7 Basic Requirements: Atmospheric Conditioning, ISTA 2A Compression, Fixed Displacement or Random Vibration and shock testing Alarm systems - Part 5: Environmental test methods EN 50130-5:98; EN 50130-5:11 (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 1 of 11
Operating conditions Section 2: Environmental conditions (climatic, mechanical and other non-electrical influences) Altitude & Pressure Network Equipment - Building System (NEBS) requirements: Physical Protection, Clause 5.1.3 Operating Altitude IEC 60870-2-2 GR-63-CORE:06 Environmental Testing - Part 2: Tests - IEC 60068-2-13 Test M: Low Air Pressure Environmental Engineering Considerations and Laboratory Tests: Method 500 Procedure I/II MIL-STD 810B:67 + Notice 1:69 + Notice 2:69 + Method 504 Procedure I ; Method 518.1 Procedure I Method 500.1 Procedure I/II MIL-STD 810C:75 + Notice 1:81 Method 504.1 Procedure I Method 518.1 Procedure I Method 500.2 Procedure I/II/III MIL-STD 810D:83 + Notice 1:86 Method 520.0 Procedure III Method 500.3 Procedure I/II/III MIL-STD 810E:89 + Notice 1:90 + Notice 2:93 + Method 520.1 Procedure III Method 500.4 Procedure I/II/III MIL-STD 810F:00 + Notice 1:00 + Notice 2:02 + Method 520.2 Procedure III Method 500.5 Procedure I/II/III MIL-STD 810G:08 Method 520.3 Procedure III Method 500.6 Procedure I/II/III Method 520.4 Procedure III Section 4.0 Temperature and Altitude test RTCA/DO-160D:97 + CHG1:00 + CHG2:01 + RTCA/DO-160E:04; RTCA/DO-160F:07; RTCA/DO-160G:10 + CHG1:14 DEF STAN 00-35, Part 3, Issue 4:06 Section 3: Chapters: 9, 11-13, 15, 20 DEF STAN 00-035, Part 3, Issue 5:17 Section 3: Chapters: 9, 11-13, 15, 20 IEEE Standard Environmental and Testing IEEE Std 1613:09 + A1:11 Requirements for Communications Networking Devices Installed in Electric Power Substations. Section 3.3: Altitude Communication Networks and Systems in IEC 61850-3 Substations - Part 3: General Requirements. Clause: 5.4 Barometric Pressure IEC 60601-1-11:10 Selected clauses (4.2.2c, 4.2.2d) (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 2 of 11
Selected clauses (4.2.3.1d, 4.2.3.1e) Standard Test Methods for Determining the Effects of High Altitude on Packaging Systems by Vacuum Method Temperature and Humidity Environmental Testing - Part 2: Tests - Test A: Cold Environmental Testing - Part 2: Tests - Test B: Dry Heat Environmental Testing - Part 2: Tests - Test N: Change of Temperature Environmental Testing - Part 2-30: Tests - Test Db: Damp Heat, Cyclic (12 h + 12 h cycle) Environmental Testing - Part 2: Tests - Test Z/AD: Composite Temperature/Humidity Cyclic Test Environmental Testing Part 2: Tests - Test Cb: Damp Heat, Steady State, Primarily for Equipment Environmental Testing - Part 2-78: Tests - Test 2-78: Body Cab: Damp Heat, Steady State Network Equipment Building System (NEBS) Requirements: Physical Protection Clause 5.1.1.1/2/3; Clause 5.1.2 Environmental Engineering Considerations and Laboratory Tests: Method 501, Procedure I/II Method 502, Procedure I Method 503, Procedure I Method 507, Procedures I/II/III/IV/V Method 501.1, Procedure I/II Method 502.1, Procedure I Method 503.1, Procedure I Method 507.1, Procedures I/II/III/IV/V Method 501.2, Procedure I/II Method 502.2, Procedure I/II/III Method 503.2, Procedure I Method 507.2, Procedures I/II/III Method 501.3, Procedure I/II Method 502.3, Procedure I/II/III Method 503.3, Procedure I Method 507.3, Procedures I/II/III IEC 60601-1-11 ASTM D6653/D6653M 01(R2010); ASTM D6653/D6653M IEC 60068-2-1:90 + A2:94; IEC 60068-2-1 IEC 60068-2-2:74 + A1:93 + A2:94; IEC 60068-2-2 IEC 60068-2-14:84 + A1:86; IEC 60068-2-14 IEC 60068-2-30:80 + A1:85; IEC 60068-2-30 IEC 60068-2-38:74; IEC 60068-2-38 IEC 60068-2-56:88 IEC 60068-2-78:01; IEC 60068-2-78 GR-63-CORE:06 MIL-STD 810B:67 + Notice 1:69 + Notice 2:69 + MIL-STD 810C:75 + Notice 1:81 MIL-STD 810D:83 + Notice 1:86 MIL-STD 810E:89 + Notice 1:90 + Notice 2:93 + (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 3 of 11
Method 501.4, Procedure I/II Method 502.4, Procedure I/II/III Method 503.4, Procedure I/II Method 507.4, Procedure I Method 501.5, Procedure I/II Method 502.5, Procedure I/II/III Method 503.5, Procedure I Method 507.5, Procedure I/II Method 501.6, Procedure I/II Method 502.6, Procedure I/II/III Method 503.6, Procedure I Method 507.5, Procedure I/II Section 5.0 Temperature Variation Test Section 6.0 Humidity Test Preferred Atmosphere Accelerated Aging of Sterile Barrier Systems for Medical Devices Specification for Environmental Testing of Switching and Transmission Equipment at India Paragraph 8.0, Category A, B, C, D, Humidity Paragraph 10.0, Category A, B, C, D, Humidity Paragraph 6.0, Category A, B, C, D, Low Temperature Paragraph 7.0, Category A, B, C, D, High Temperature Paragraph 9.0, Category A, B, C, D, Thermal Shock Section 3: Chapters: 1, 2, 4, 5, 7, 14, 21 Section 3: Chapters: 1, 2, 4, 5, 6, 7, 14, 21 IEEE Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Electric Power Substations. Section: 3.1: Usual service conditions Communication Networks and Systems in Substations - Part 3: General Requirements. Clauses: 5.2 Temperature 5.3 Humidity MIL-STD 810F:00 + Notice 1:00 + Notice 2:02 + MIL-STD 810G:08 RTCA/DO-160D: 97 + CHG1:00 + CHG2:01+ RTCA/DO-160E:04; RTCA/DO-160F:07; RTCA/DO-160G:10 + CHG1:14 ASTM D4332-01; ASTM D4332-01(2006) 1 ; ASTM D4332 ASTM F1980-07(R2011); ASTM F1980 QM-333 DEF STAN 00-35 Part 3 Issue 4: 06 DEF STAN 00-035, Part 3, Issue 5:17 IEEE Std 1613:09 + A1:11 IEC 61850-3 (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 4 of 11
Needle-based Injection Systems for Medical use - Requirements and Test Methods - Part 1: Needle-based Injection Systems. Sections: 10.2 Cool, standard and warm atmosphere testing 10.4 Life-cycle testing 10.6 Dry-heat and cold-storage testing 10.7 Damp-heat testing 10.8 Cyclical testing Pen-injectors for medical use - Part 4: Requirements and Test Methods for electronic and electromechanical pen-injectors. Sections: 6.1 Standard atmosphere 6.2 Cool atmosphere 6.3 Hot atmosphere 7.1 Preconditioning in dry heat atmosphere 7.2 Preconditioning in cold storage atmosphere 7.3 Preconditioning in cyclical atmosphere 7.9 Preconditioning for damp heat Selected clauses (4.2.1, 4.2.2, 4.2.3) Selected clauses (4.2.1, 4.2.2, 4.2.3.1, and 4.2.3.2) ISO 11608-1 ISO 11608-4 IEC 60601-1-11:10 IEC 60601-1-11 Mechanical Shock Environmental Testing - Part 2: Tests - Test Ea and Guidance: Shock Environmental Testing - Part 2: Tests - Test Eb and Guidance: Bump Environmental testing - Part 2: Tests - Test Eh: Hammer Tests Railway Applications Rolling Stock Equipment - IEC 60068-2-27:87; IEC 60068-2-27 IEC 60068-2-29:87 IEC 60068-2-75 IEC 61373 Shock and Vibration Tests Environmental Engineering Considerations and Laboratory Tests: Method 516 Procedure I/III/IV MIL-STD 810B:67 + Notice 1:69 + Notice 2:69 + Method 516.2 Procedure I/III/IV MIL-STD 810C:75 + Notice 1:81 Method 516.3 Procedure I/II/V MIL-STD 810D:83 + Notice 1:86 Method 516.4 Procedure I/II/V MIL-STD 810E:89 + Notice 1:90 + Notice 2:93 + Method 516.5 Procedure I/II/V MIL-STD 810F: 00 + Notice 1:00 + Notice 2:02 + Method 516.6 Procedure I/II/V MIL-STD 810G:08 Method 516.7, Procedure I/II/V (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 5 of 11
Section 7.0 Operational Shock and Crash Safety Test Section 2: Chapters: 03, 12 Section 2: Chapters: 03, 12 IEEE Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Electric Power Substations. Section: 9 Vibration and shock Pen-injectors for Medical use - Part 4: Requirements and Test Methods for Electronic and Electromechanical Pen-injectors. Section: 7.6 Preconditioning by shock Medical electrical equipment Selected clauses (10.1.2a, 10.1.3a, 10.1.3b) Vibration Testing Environmental Testing - Part 2: Tests - Test Fc: Vibration (Sinusoidal) Basic Environmental Testing Procedures Part 2: Tests - Test Ee and Guidance: Bounce Environmental Testing - Part 2: Tests - Test Fh: Vibration, Broad-band Random (Digital Control) and Guidance Network Equipment - Building System (NEBS) Requirements: Physical Protection Clause 5.4.2 - Office vibration Clause 5.4.3 - Transportation vibration Specification for Environmental Testing of Switching and Transmission Equipment at India Paragraph 12.0, Category A, B, C, D, Sine Vibration Environmental Engineering Considerations and Laboratory Tests: Method 514 Random Vibration Method 519.1, Gunfire Vibration Method 514.2, Random Vibration Method 519.2, Gunfire Vibration Method 514.3, Random Vibration Method 519.3, Gunfire Vibration Method 514.4, Random Vibration Method 519.4, Gunfire Vibration Method 514.5, Random Vibration, Method 519.5, Gunfire Vibration RTCA/DO-160 D: 97 + CHG1:00 + CHG2:01 + RTCA/DO-160E:04; RTCA/DO-160F:07; RTCA/DO-160G:10 + CHG1:14 DEF STAN 00-35 Part 3 Issue 4:06 DEF STAN 00-035, Part 3, Issue 5:17 IEEE Std 1613:09 + A1:11 ISO 11608-4 IEC 60601-1-11:10; IEC 60601-1-11 IEC 60068-2-6:95; IEC 60068-2-6 IEC 60068-2-55:87; IEC 60068-2-55 IEC 60068-2-64:93; IEC 60068-2-64 GR-63-CORE:06 QM-333 MIL-STD 810B:67 + Notice 1:69 + Notice 2:69 + MIL-STD 810C:75 + Notice 1:81 MIL-STD 810D:83 + Notice 1:86 MIL-STD 810E:89 + Notice 1:90 + Notice 2:93 + MIL-STD 810F:00 + Notice 1:00 + Notice 2:02 + (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 6 of 11
Method 514.6, Random Vibration, MIL-STD 810G:08 Method 519.6, Gunfire Vibration Method 528, Mechanical Vibrations of Shipboard Equipment Method 514.7, Random Vibration, Method 519.7, Gunfire Vibration Method 528.1, Mechanical Vibrations of Shipboard Equipment Mechanical Vibrations of Shipboard Equipment MIL-STD 167-1A:05 Section 8.0 Vibration Test RTCA/DO-160D: 97 + CHG1:00 + CHG2:01 + RTCA/DO-160E:04; RTCA/DO-160F:07; RTCA/DO-160G:10 + CHG1:14 Performance Testing of Shipping Containers and System Vibration Testing Section 2: Chapter: 01 Section 2: Chapter: 01 IEEE Standard Environmental and Testing Requirements for Communications Networking Devices Installed in Electric Power Substations. Section: 9 Vibration and Shock Communication networks and Systems in Substations - Part 3: General Requirements Section: 5.5 Mechanical and Seismic Needle-based Injection Systems for Medical use Requirements and Test Methods Part 1: Needle-based Injection Systems. Section: 10.9 Vibration Testing Pen-injectors for Medical use - Part 4: Requirements and Test Methods for Electronic and Electromechanical Pen-injectors. Section: 7.5 Preconditioning by Vibration Selected Clauses (10.1.2b, 10.1.3c) ASTM D4169-99 1 ; ASTM D4169-08 1 ; ASTM D4169-09; ASTM D4169-14; ASTM D4169 ASTM D999-01 1 ; ASTM D999 ASTM D4728 DEF STAN 00-35 Part 3 Issue 4:06 DEF STAN 00-035, Part 3, Issue 5:17 IEEE Std 1613:09 + A1:11 IEC 61850-3 ISO 11608-1 ISO 11608-4 IEC 60601-1-11:10; IEC 60601-1-11 Rain or Water (Immersion), Dust, and Salt Fog Environmental Testing - Part 2: Tests - Test Ka: Salt Mist Environmental Testing - Part 2: Tests - Test R and Guidance: Water IEC 60068-2-11 IEC 60068-2-18 (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 7 of 11
Environmental Testing. Part 2: Tests - Test Kb: Salt Mist, Cyclic (Sodium Chloride solution) Degrees of Protection Provided by Enclosure (IP Code) Environmental Testing - Part 2: Tests - Test L: Dust and Sand Selected clauses (8.3.1) Standard Practice for Operating Salt Spray (Fog) Apparatus Environmental Engineering Considerations and Laboratory Tests: Method 506, Rain, Method 509, Salt Fog, Method 510, Dust Test Method 512, Leakage (Immersion) Method 506.1, Rain, Method 509.1, Salt Fog, Method 510.1, Dust (Fine Sand) Method 512.1, Leakage (Immersion) Method 506.2, Rain, Method 509.2, Salt Fog, Procedure I Method 510.2, Sand and Dust Method 512.2, Leakage (Immersion) Method 506.3, Rain, Method 509.3 Salt Fog, Method 510.3, Sand and Dust Method 512.3, Leakage (Immersion) Method 506.4, Rain, Method 509.4, Salt Fog, Method 510.4, Sand and Dust, Method 512.4, Immersion Method 506.5, Rain, Method 509.5, Salt Fog, Method 510.5, Sand and Dust, Method 512.5, Immersion Method 506.6, Rain, Method 509.6, Salt Fog, Method 510.6, Sand and Dust, Method 512.6, Immersion Section 10.0 Waterproofness Test, Section 12.0 Sand and Dust Test, Section 14.0 Salt Fog Test Pen-injectors for Medical use - Part 4: Requirements and Test Methods for Electronic and Electromechanical Pen-injectors. Section: 7.8 Preconditioning for Dust Test IEC 60068-2-52 IEC 60529:89 + A1:99 IEC 60068-2-68 IEC 60601-1-11:10; IEC 60601-1-11 ASTM B117 MIL-STD 810B:67 + Notice 1:69 + Notice 2:69 + MIL-STD 810C:75 + Notice 1:81 MIL-STD 810D:83 + Notice 1:86 MIL-STD 810E:89 + Notice 1:90 + Notice 2:93 + MIL-STD 810F:00 + Notice 1:00 + Notice 2:02 + MIL-STD 810G:08 RTCA/DO-160D:97 + CHG1:00 + CHG2:01 + RTCA/DO-160E:04; RTCA/DO-160F:07; RTCA/DO-160G:10 + CHG1:14 ISO 11608-4 (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 8 of 11
Section 3: Chapters: 25-29 Section 3: Chapters: 25-29 DEF STAN 00-35 Part 3 Issue 4:06 DEF STAN 00-035, Part 3, Issue 5:17 Free Fall / Drop Environmental Testing - Part 2: Tests - Test Ec: Topple Environmental Testing - Part 2: Tests - Test Ed: Free Fall (Procedure 1) Network Equipment - Building System (NEBS) Requirements: Physical Protection - Clause 5.3.1 Handling Drop Tests - Packaging Equipment - Clause 5.3.2, Unpackaged Equipment Drop Test IEC 60068-2-31:69 + A1:82; IEC 60068-2-31 IEC 60068-2-32:75 + A1:88 + A2:90; GR-63-CORE:06 Environmental Engineering Considerations and Laboratory Tests Method 516.1, Shock, Procedure II, V MIL-STD 810B:67 + Notice 1:69 + Notice 2:69 + Method 516.2, Shock, Procedure II, V MIL-STD 810C:75 + Notice 1:81 Method 516.3, Shock, Procedure IV, VI MIL-STD 810D:83 + Notice 1:86 Method 516.4, Shock, Procedure IV, VI MIL-STD 810E:89 + Notice 1:90 + Notice 2:93 + Method 516.5, Shock, Procedure IV, VI MIL-STD 810F:00 + Notice 1:00 + Notice 2:02 + Method 516.6 Shock, Procedure IV, VI MIL-STD 810G:08 Method 516.7 Shock, Procedure IV, VI Paragraph 13.0, Category A, B, C, D Handling Drop ASTM D4169-99 1 ; ASTM D4169-08 1 ; ASTM D4169-09; ASTM D4169-14; ASTM D4169 Drop Test of Loaded Containers by Free Fall Standard Test Methods for Rough Handling of Unitized Loads and Large Shipping Cases and Crates Standard Test Method for Concentrated Impacts to Transport Packages Standard test Method for Determining Compressive Resistance of shipping Containers, Components, and Unit Loads Communication Networks and Systems in Substations - Part 3: General Requirements Clause: 5.5 Mechanical and Seismic QM-333 ASTM D5276 ASTM D6179 ASTM D6344 ASTM D642 IEC 61850-3 (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 9 of 11
Needle-based injection Systems for Medical use - Requirements and Test Methods - Part 1: Needle-based Injection Systems. Section: 10.5 Free-fall Testing Pen-injectors for Medical use - Part 4: Requirements and Test Methods for Electronic and Electromechanical Pen-injectors. Section: 7.4 Preconditioning by Free Fall Selected clauses (10.1.3d) ISO 11608-1 ISO 11608-4 IEC 60601-1-11:10; IEC 60601-1-11 Contamination by Fluids Method 504, Contamination by Fluids MIL-STD 810F:00 + Notice 1:00 + Notice 2:02 + Method 504.1, Contamination by Fluids MIL-STD 810G:08 Method 504.2, Contamination by Fluids Section 11.0 Fluids Susceptibility Test RTCA/DO-160D: 97 + CHG1:00 + CHG2:01 + RTCA/DO-160E:04; RTCA/DO-160F:07; RTCA/DO-160G:10+ CHG1:14 Explosive Atmosphere Method 511 Explosive Atmosphere MIL-STD 810B:67 + Notice 1:69 + Notice 2:69 + Method 511.1 Explosive Atmosphere MIL-STD 810C:75 + Notice 1:81 Method 511.2 Explosive Atmosphere MIL-STD 810D:83 + Notice 1:86 Method 511.3 Explosive Atmosphere MIL-STD 810E:89 + Notice 1:90 + Notice 2:93 + Method 511.4 Explosive Atmosphere MIL-STD 810F:00 + Notice 1:00 + Notice 2:02 + Method 511.5 Explosive Atmosphere MIL-STD 810G:08 Method 511.6 Explosive Atmosphere Section 9.0 Explosive Proofness Test RTCA/DO-160D: 97 + CHG1:00 + CHG2:01 + RTCA/DO-160E:04; RTCA/DO-160F:07; RTCA/DO-160G:10+ CHG1:14 Solar Radiation (Sunshine) Environmental Testing - Part 2-5: Tests - Test Sa: Simulated Solar radiation at Ground Level and Guidance for Solar Radiation Testing Method 505, Procedure I IEC 60068-2-5:75; EN 60068-2-5:99; IEC 60068-2-5; EN 60068-2-5 MIL-STD-810:62 Method 505.1, Procedure I MIL-STD-810A:64 Method 505, Procedure I, II MIL-STD-810B:67 + Notice 1:69 + Notice 2:69 + Method 505.1, Procedure I, II MIL-STD 810C:75 + Notice 1:81 Method 505.2, Procedure I, II MIL-STD 810D:83 + Notice 1:86 Method 505.3, Procedure I, II MIL-STD 810E:89 + Notice 1:90 + Notice 2:93 + (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 10 of 11
Method 505.4, Procedure I, II MIL-STD 810F:00 + Notice 1:00 + Notice 2:02 + Method 505.5, Procedure I, II MIL-STD 810G:08 Method 505.6, Procedure I, II Paragraphs 24, 25 Simulated Solar Radiation EN 50130-5:98; EN 50130-5 Highly Accelerated Life Test Cold Temperature Steps Hot Temperature Steps Rapid Temperature Changes Random Vibration - 3 Axis Combined Temperature and Vibration Highly Accelerated Stress Screening (HASS) Stress Profile Definition GM Worldwide Engineering Standards Test Procedure Analysis GMW8287 1 Note: This laboratory s scope contains withdrawn or superseded methods. As a clarifier, this indicates that the applicable method itself has been withdrawn or is now considered historical and not that the laboratory s accreditation for the method has been withdrawn. (A2LA Cert. No. 0839.04) Revised 01/08/2018 Page 11 of 11
Accredited Laboratory A2LA has accredited HERMON LABORATORIES Binyamina, Israel for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 10 th day of October 2017. President and CEO For the Accreditation Council Certificate Number 0839.04 Valid to May 31, 2019 For the tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.