WANG TAPPING SADDLES 0-0 fast, permanent tapping SOLUTION FOR BOTH rigid and flexible pipe types FEATURES bodies are manufactured from either stainless steel or Ductile Iron Fusion Bonded Epoxy coated (depending on saddle type) with stainless steel fasteners Nitrile rubber gaskets provide a potable water approved seal in all saddle types. Larger diameter Rigi-Tap saddles ( 00 and larger) employ an EPDM back mat, insulating against galvanic corrosion Fully passivated stainless steel underscore the quality of the product Dry film coating employed to minimise galling of the stainless steel fasteners All sharp surfaces linished to avoid injury to the installer Supplied with detailed installation instructions and pipe type compatability information Manufacturing facility certified to the ISO 00 Quality Assured Standard DESCRIPTION TECHNICAL DATA WANG Tapping s provide a quick and permanent means of tapping into both rigid and flexible pipe types Tapping saddles are ideal for service connections and provide an effective means of conducting an under pressure tapping The saddle body supplies a strong reinforced aperture for the parent and offtake pipe Note. This product is not suitable for gas application Range: 0-0 Depending on saddle type.see selection chart inside Maximum Operating Pressure: 00 kpa Temperature Range: -0 C to 0 C Relevant Standards: AS/NZS Lic. No. SMK00
WANG RIGI-TAP TAPPING SADDLES Pipe Pipe Type Application Rigid Non PVC Flexible All PVC 0-0 STANDARD CLAMP DATA Typical specifying sequence Offtake Code Prefix No.of Studs Stud No. of Segments Width OD Range Example KT T 00 0-0, KT M KT = Tapping 0-0 0,,, 0, 0 KT M 0 = number of studs only indicated on RIGI-TAP s. = stud / = studs 00-0 0,,, 0, 0 KT M 0 = delineator = size (start of the OD range) T 00 = Offtake type (indicates female threaded BSP offtake) = nominal offtake size. 00 = 0 / 0 = / 0 = / 00 = 0 / 00 = 0 KT TAPPING SADDLE parts list No Description Material / Standard Skin Stainless Steel / ASTM A0M Locking Plate Stainless Steel / ASTM A0M Studs Stainless Steel / Anti-galling compound coated ASTM A KT TAPPING SADDLE Nuts Stainless Steel / Anti-galling compound coated ISO 0, AS. Washer Stainless Steel / ISO Lugs Stainless Steel / ASTM A0M Flat Bars Stainless Steel / ASTM A0M Sealing Gasket Nitrile (NBR) compound / AS and AS/NZS 00 BSP Offtake Stainless Steel ASTM AM, ISO or ANSI B., AS.
WANG FLEXI-TAP TAPPING SADDLES Pipe Pipe Type Application Rigid Non PVC Flexible All PVC 00-0 STANDARD CLAMP DATA Typical specifying sequence Offtake Code Prefix No.of Studs Stud No. of Segments Width OD Range Example KT F S T 00 00-0 0,,, 0, 0 KTFS M 0 KT = Tapping F = Flexible pipe S = Stainless steel saddle body = Delineator = size (fixed OD) T 00 = Offtake type (indicates female threaded BSP offtake) = nominal offtake size. 00 = 0 / 0 = / 0 = / 00 = 0 / 00 = 0 parts list No. Description Material / Standard Skin Stainless Steel / ASTM A0M Locking Plate Stainless Steel / ASTM A0M Studs Nuts Stainless Steel / Anti-galling compound coated ASTM A Stainless Steel / Anti-galling compound coated ISO 0, AS. Washer Stainless Steel / ISO Lugs Stainless Steel / ASTM A0M Flat Bars Stainless Steel / ASTM A0M Sealing Gasket Nitrile (NBR) compound / AS and AS/NZS 00 BSP Offtake Stainless Steel ASTM AM, ISO or ANSI B., AS.
WANG VARI-TAP TAPPING SADDLES Pipe Pipe Type Application Rigid Non PVC Flexible All PVC 00, 0 STANDARD CLAMP DATA Typical specifying sequence Offtake Code Prefix No.of Studs Stud No. of Segments Width OD Range* Example KT F D T 00 00 0, KTFD M 0-0 0, KTFD M 0 - KT F D = Tapping = Flexible pipe = DI-FBE coated saddle body = Delineator * T = OD in flexible configuration = Offtake type (indicates female threaded BSP offtake) 00 = Nominal offtake size. 00 = 0 / 0 = SADDLE CONFIGURATION INDICATOR parts list No. Description Material / Standard Top Segment Ductile Iron / AS Bottom Segment Ductile Iron / AS Bolt M x Hex Head Stainless Steel / AS0 Washer - M Stainless Steel / ISO 0 Nut Retaining O-Ring Nitrile (NBR) Rubber Stainless Steel Anti-galling compound coated ISO 0, AS. Ring Seal Gasket Nitrile (NBR) Rubber / AS & AS00 BSP thread RP ISO. Coating Fusion Bonded Epoxy / AS
WANG Tapping s - PN OPERATING PRESSURE rigid and flexible pressure pipe RIGI-TAP FLEXI-TAP VARI-TAP Pipe 0 0 0 00 0 00 0 00 0 00 0 RIGID PIPE FLEXIBLE PIPE DICL Steel CICL AC ABS* GRP* RC PVC HDPE MSCL GWI B C AB CD Series Series - B Series (U) AS/NZS AS/NZS AS AS 0 AS AS AS AS AS AS AS 0 (M) AS/NZS AS/NZS 0 (O) AS/NZS KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? Select missing 0 offtake size as shown 0 KT-0T0?? in the typical specifying KT-0T0?? sequence KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? 0 KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KTFD-T0?? 0 0 0 KT-T0?? KT-T0?? KT-0T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-0T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KTFD-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? KT-T0?? *** KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T?? KT-0T0?? *** 0 KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? *** KT-0T0?? KT-T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-T0?? KT-0T0?? KT-T0?? *** KT-T0?? KT-T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? *** 0 00 KT-0T0?? KT-0T0?? KT-0T0?? 0 S Steel Rigi-Tap option Cast Vari-Tap option KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? KT-0T0?? *** 0 0 0 0 00 0 0 Pipe OD KTFD-T0?? 0 *** Contact Pentair Water Solutions for further information and availability of this product. * Min. required pipe rating for saddle application: PN * Min. required pipe rating for saddle application: SN0,000
WANG CLAMPS & COUPLINGS WANG is one of the leading manufacturers and suppliers of Grade Stainless Steel Repair and Tapped as well as Couplings for reticulated water, sewerage and gas mains including industrial piping systems. As part of the Pentair Water Solutions business, WANG products have become synonymous with quality and reliability. Our product range is widely utilised and relied upon by Water Authorities and Councils throughout Australia in the installation and maintenance of their supply mains and reticulation network. Quality ISO 00 Wang Components products can be sourced through the Pentair Water Solutions national sales and service network of customer centres. Pentair Water Solutions is a specialist in integrated solutions for all your water and wastewater pipeline system requirements. KWIK A full circle repair clamp for small bore galvanised steel, copper and PVC pipe. - 0 Repair A fast, permanent and economical repair solution for most pipe types and sizes. 0-00 Tapped A reliable means of tapping into old, unstable or damaged pipe. 0-00 HDPE Provide fast, expedient on-site repair and tapping solutions for HDPE pipe. 0-00 Flanged Offtake A cost effective means of achieving a T connection or under pressure tapping. 00-00 Sewer OB Junction A quick method of installing a new property service connection on a sewer main. 00-0 Vari GIB COUPLINGS Non-restrained mechanical couplings for connecting pipes with equal or unequal diameters. 0-00 High Pressure Couplings Provides a mechanical joint between similar or dissimilar pipes in high pressure environments. 0-000 Socket Joint Leak Provide a permanent and economical seal over a leaking socket-spigot joint. 0-00 PENTAIR WATER SOLUTIONS LEVEL, GEORGE STREET, PARRAMATTA, NEW SOUTH WALES 0 / WWW.PENTAIR.COM/WATERSOLUTIONS PHONE 0 00 AUSTRALIA / 0 0 NEW ZEALAND All Pentair trademarks and logos are owned by Pentair Ltd. All other brand or product names are trademarks or registered marks of their respective owners. Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice. PNR_TS0 0 Pentair Ltd. All Rights Reserved.