~ SEE DETAIL 05/2.0 FOR EDGE DETAILING ~ NE~ SCHEDULE 80 PVC ELBO~ AS REQUIRED TO TURN UNDER SOFFIT FOR INSTALLATION OF NE~ VERTICAL DOWNSPOUT NE~ DOWNSPOUT STRAP ATIACHED TO EXISTING WALL ~ITH NE~ MASONRY ANCHORS (6' O.C. MAXIMUM) NE~ 4 11 SCHEDULE 80 PVC DO~NSPOUT DOWNSPOUT Sc.ale: None
Enhanced Performance Roof Hatches Our Most EnergyEfficient Model Yet! The new thermally enhanced design features special gasketing and increased insulation for superior thermal performance to improve the energy efficiency of your building. Energy efficiency exceeds standard hatches by more than 48% Meets LEED standards for recycled content High solar reflective index (SRI) Ozonefriendly polyisocyanurate insulation EPDM gasketing with enhanced weatherresistance Type S50T Roof Hatch Available in a Number of Standard Sizes www.bilco.com Type L50T Type NB50T
Specifications Furnish and install where indicated on plans metal roof hatch. Length denotes hinge side. These roof hatches shall be single leaf. The roof hatch shall be preassembled from the manufacturer. Performance Characteristics: Cover: Cover Insulation: Curb: Cover shall be reinforced to support a minimum live load of 40 psf (195 kg/m 2 ) with a maximum deflection of 1/0th of the span or 20 psf (97 kg/m 2 ) wind uplift. Operation of the cover shall be smooth and easy with controlled operation throughout the entire arc of opening and closing. Operation of the cover shall not be affected by temperature. Entire hatch shall be weathertight with fully welded corner joints on cover and curb..090 (2.3mm) aluminum with a 4 (102mm) beaded flange with formed reinforcing members. Cover shall have a heavy extruded EPDM rubber gasket which is bonded to the cover interior to ensure a continuous seal when compressed to the top surface of the curb. Shall be polyisocyanurate of 2 (50mm) thickness with an Rvalue of 12. Insulation shall be fully covered and protected by an aluminum liner. Shall be 12 (305mm) in height and of.090 (2.3mm) aluminum. The curb shall be formed with a 4½ (114mm) flange with 7 16 (11mm) holes provided for securing to the roof deck. The curb shall be equipped with an integral metal capflashing of the same gauge and material as the curb, fully welded at the corners, that features the Bilclip flashing system, including stamped tabs, 6 (3mm) on center, to be bent inward to hold single ply roofing membrane securely in place. Curb Shall be polyisocyanurate of 2 (50mm) thickness with an Insulation: Rvalue of 12. Lifting Mechanisms: Hardware: Finishes: Manufacturer shall provide compression spring operators enclosed in telescopic tubes to provide smooth, easy, and controlled cover operation throughout the entire arc of opening and closing. The upper tube shall be the outer tube to prevent accumulation of moisture, grit, and debris inside the lower tube assembly. The lower tube shall interlock with a flanged support shoe that is bolted to the curb assembly. Heavy stainless steel pintle hinges shall be provided. Cover shall be equipped with a spring latch with interior and exterior turn handles. Shall be equipped with interior and exterior padlock hasps. The latch strike shall be bolted to the curb assembly. Cover shall automatically lock in the open position with a rigid hold open arm equipped with a 1 (25mm) diameter red vinyl grip handle to permit easy release for closing. Compression spring tubes shall be an anticorrosive composite material and all other hardware shall be zinc plated and chromate sealed. Springs shall have an electrocoated acrylic finish for corrosion resistance. [For installation in highly corrosive environments or when prolonged exposure to hot water or steam is anticipated, specify Type 316 stainless steel hardware]. Cover hardware shall be bolted into heavy gauge channel reinforcing welded to the underside of the cover and concealed within the insulation space. Factory finish shall be mill finish aluminum. EPDM Finger Type Gasket Type S50T and E50T shown. All other models open to 90. The Bilco Company New Haven, CT 06505 2039346363 Fax: 2039338478 Email: bilco @bilco.com www.bilco.com Standard Sizes & Weights TYPE SIZE Inside Frame Opening WEIGHT inches mm lbs. kgs. S50T 36 x 30 (H) 9 x 760 (H) 132 60 E50T 36 x 36 9 x 9 143 65 NB50T 30 x 54 (H) 760 x 1370 (H) 168 76 L50T 30 x 96 (H) 760 x 2440 (H) 287 130 F50T 48 x 48 1220 x 1220 249 113 H = Hinge Side Special sizes available upon request 2010 The Bilco Company LEED is a registered trademark of the U.S. Green Building Council Printed on recycled paper Printed in the USA EPRHFLYERR3
LadderUP Safety Post Standard Features and Benefits Adjustable mounting hardware accommodates virtually any ladder rung size or spacing Telescoping design is spring balanced for ease of operation Automatically locks in the fully raised position to provide the user with a firm and steady handhold Handy release lever allows the post to be easily lowered to its retracted position Available in four levels of corrosion resistance to provide many years of trouble free, dependable service Specifications: Install on fixed ladder(s) below hatch cover(s), LadderUP safety post Model as manufactured by The Bilco Company. Device shall be (refer to chart for material/finish of model specified). It shall be designed with a telescoping tubular section that locks automatically when fully extended. Upward and downward movement shall be controlled by a stainless steel spring balancing mechanism. Unit shall be completely assembled with fasteners for securing to the ladder rungs in accordance with the manufacturer s instructions. If installation is to be in corrosive atmosphere, specify Model LU2, LU3 or LU4 as conditions warrant. Standard Sizes and Weights Model Material/Finish lbs. Weight LadderUP Safety Posts provide easier, safer ladder access through roof hatches, floor access doors and manholes. This telescoping post permanently mounts to the top two rungs of anyfixed ladder, providing a positive handhold and enabling the user to enter or exit an opening in an upright and balanced position. kg. LU1* Steel, yellow powder coat 24 11 LU2 Steel, hot dip galvanized 24 11 LU3 Type 304 Stainless Steel, sand blast finish 24 11 LU4 Aluminum, mill finish 14 7 *LU1 can be supplied with a black powder coat finish on request. CAD details, BIM Models, 3part specifications available on www.bilco.com
14 RUNG STANDARD F14S M Modular Fixed Ladder 40" Construction 28" 7" 12 3 /4" 42" 32" 28" Cotterman fixed steel ladder accessories are designed to provide an additional measure of safety or security for any fixed steel ladder. FIXED STEEL LADDERS F AND M without safety cages. OSHA requires safety cages on ladder heights POWDER Cotterman fixed steel ladders are designed for use where safe, solid vertical climbing access is required. Series F and Series M modular fixed steel exceeding 20'. Separate cages are offered for updating older ladders to COATED current safety standards. All Cotterman fixed ladders meet or exceed TOUGH ladders are available with and without walkthru handrails at the top landing surface. Standard fixed and walkthru models can be used up to 20' OSHA 1910.27 and 1926.1053 TM standards. 9 /16" DIA. HOLE 32 1 /2" 14 RUNG WITH CAGE F14SC 16" 40 19 1 /4" 24" ACCESSORIES SAFETY CHAIN OPTIONAL F FIXED LADDERS: Ladders are heavy duty onepiece welded assemblies. M MODULAR FIXED LADDERS: Ladders are heavy duty subassemblies, no section is greater than 7' in length. CONSTRUCTION FEATURES: Side members are 1 /4"x2"x2" steel angle. Climbing rungs are 3 /4" corrugated steel round rungs space on 12" centers. Standoff brackets are 7". Gray powder coat finish is standard color, yellow available. FIXED LADDERS WITH SAFETY CAGES: Standard fixed steel ladders are combined with safety cage protection. They are available in 10' through 29' sizes and are ideal for hatchway or side step landing access. CAGE FEATURES: OSHA design safety cages have flared bottom opening for easy entry. Left or right side step access cage designs are available at no charge. Cage begins 7' from bottom of ladder. Gray powder coat finish, yellow available. SPECIFICATIONS STANDARD WITH CAGE LENGTH: TOP TO M OVERALL LENGTH BOTTOM RUNG RUNGS SHPG. WT. PRICE SHPG. WT. 3'3" 4'3" 5'3" 6'3" 7'3" 8'8" 9'3" 10'3" 11'3" 12'3" 13'3" 14'3" '3" 16'3" 17'3" 18'3" 19'3" 20'3" 3' 4' 5' 6' 7' 8' 9' 10' 11' 12' 13' 14' ' 16' 17' 18' 19' 20' 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 20 21 F4S F5S F6S F7S F8S F9S F10S F11S F12S F13S F14S FS F16S F17S F18S F19S F20S 35 43 52 60 68 77 88 96 105 113 122 130 139 0 8 167 175 STANDOFF LANDING PLATFORM: Standoff landing platforms with offset caged ladders are required by OSHA Standard 1910.27 at 30' maximum height intervals. These rugged, preengineered platforms are constructed with left or right entries as required. PRICE OSHA NOTE: Although not required by OSHA, safety caging is offered on 11 thru 20 rung models. M11SC M12SC M13SC M14SC MSC M16SC M17SC M18SC M19SC M20SC M21SC F11SC F12SC F13SC F14SC FSC F16SC F17SC F18SC F19SC F20SC F21SC 6 182 197 213 268 282 298 316 342 357 373 21'3" 21' 22 M22SC F22SC 388 22'3" 22' 23 M23SC F23SC 414 23'3" 23' 24 OSHA NOTE: M24SC F24SC 429 24'3" 24' 25 Fixed ladder heights M25SC F25SC 444 25'3" 25' 26 exceeding 20' are M26SC F26SC 471 required to 26'3" 26' 27 M27SC F27SC 486 have safety caging. 27'3" 27' 28 M28SC F28SC 501 28'3" 28' 29 M29SC F29SC 559 29'3" 29' 30 M30SC F30SC 575 OSHA NOTE: Heights exceeding 30' require a standoff platform (see option model SP) SHIPPING NOTE: All thru 28 rung Series F models with cages ship in 2 sections. All 29 and 30 rung models ship in 3 sections. HOT DIP GALVANIZED FINISH OR STAINLESS STEEL CONTSTRUCTION CAN BE QUOTED. RIGHT SIDE ENTRY SHOWN A MINIMUM OF 11' DIA. SURFACE REQUIRED SP CG FIXED LADDER WITH WALKTHRU HANDRAILS: Ladders are designed for applications where safe landing access is required. They are onepiece welded assemblies for use in applications less than 20' in vertical height. CONSTRUCTION FEATURES: Side members are 1 /4"x2"x2" steel angle. 3 /4" corrugated steel round climbing rungs on 12" centers. Standoff mounting brackets are 7". Walkthru handrails extend 42" above landing surface. Mounting brackets included. Welded onepiece, gray powder coat finish, yellow available. SPECIFICATIONS LENGTH: TOP TO BOTTOM RUNG SECURITY CAGE ENTRY GATE: The cage security gate is designed to prevent unauthorized entry into the bottom of the ladder cage. Doors have lockable hasp for complete security. FIXED LADDER WITH WALKTHRU HANDRAILS AND SAFETY CAGES: Designed for safe landing access and available from 10' to 29'. Cages and walkthru handrails extend 42" above landing surface. CAGE FEATURES: Safety cages are designed to OSHA specifications with flared bottom opening for easy entry. Cage begins 7' from bottom of ladder. Gray powder coat finish, yellow available. SECURITY LADDER GUARD: The ladder guard is mounted directly over the ladder climbing rungs to prevent unauthorized use. It is available in either 6' or 8' lengths. The guard ha a one piece piano hinge, and is furnished with lockopen and lockclosed hasps. OPTION LG6... Shipping wt. 130 lbs. OPTION LG8... SAFETY CHAIN ATTACHMENT: The safety chain attachment is used on the walkthru handrails to prevent accidental exit from the top landing surface. OPTION SP........ OPTION CG.. Shipping wt. 3 lbs. Shipping wt. 31 lbs. OPTION D3... FOR MOUNTING Shipping wt. 148 lbs. 2. 3. OVERALL LENGTH 6'8" 7'8" 8'8" 9'8" 10'8" 11'8" 12'8" 13'8" 14'8" '8" 16'8" 17'8" 18'8" 19'8" 20'8" 21'8" 22'8" 23'8" 24'8" 25'8" 26'8" 27'8" 28'8" 29'8" 30'8" 31'8" 32'8" 3' 4' 5' 6' 7' 8' 9' 10' 11' 12' 13' 14' ' 16' 17' 18' 19' 20' RUNGS 4 5 6 7 8 9 10 11 12 13 14 16 17 18 19 20 21 WALKTHRU RAIL WITH WALK THRU & CAGE M SHPG. SHPG. WT. PRICE WT. PRICE F4W F5W F6W F7W F8W F9W F10W F11W F12W F13W F14W FW F16W F17W F18W F19W F20W 61 70 78 87 95 104 1 123 132 140 148 7 165 176 185 193 202 OSHA NOTE: Although not required by OSHA, safety caging is offered on 8 thru 20 rung models. M11WC M12WC M13WC M14WC MWC M16WC M17WC M18WC M19WC M20WC M21WC F8WC F9WC F10WC F11WC F12WC F13WC F14WC FWC F16WC F17WC F18WC F19WC F20WC F21WC 167 194 211 226 242 268 284 327 353 369 384 401 428 443 21' 22 M22WC F22WC 458 22' 23 M23WC F23WC 485 23' 24 OSHA NOTE: M24WC F24WC 500 24' 25 Fixed ladder heights M25WC F25WC 5 25' 26 exceeding 20' are M26WC F26WC 571 26' 27' 27 28 required to have safety caging. M27WC M28WC F27WC F28WC 586 601 28' 29 M29WC F29WC 619 29' 30 M30WC F30WC 634 OSHA NOTE: Heights exceeding 30' require a standoff platform (see option model SP) SHIPPING NOTE: All thru 25 rung Series F models with cages ship in 2 sections. All 26 thru 30 rung models ship in 3 sections. HOT DIP GALVANIZED FINISH OR STAINLESS STEEL CONTSTRUCTION CAN BE QUOTED. LG 11 RUNG WITH WALKTHRU F11W 32" 28" 32 1 /2" 40 F construction features 11 RUNG WITH WALKTHRU AND CAGE: F11WC D3 12 3 /4" 7" 6" 1" DIA. 11 GA. TUBING 13 /32" HOLES (4) 3" APART 6"