Technical Information VESTAMID - PA 6T/X and PA 10T/X product range and main properties The following pages provide an overview of the main product information and properties of VESTAMID - PA 6T/X and PA 10T/X. In case, there are additional information missing please contact our technical support. Therefore please note our contact list on the last page. Evonik Resource Efficiency GmbH VESTAMID Januar 2016 Page 1/24
VESTAMID base and unfilled polymers VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications M1000 natural color PA6T/X Medium viscosity, semicrystalline with aromatic segments CO 3600 Manufacturing of compounds for injection molding M3000 natural color PA10T/X Medium viscosity, semicrystalline with aromatic segments; partly based on renewable raw materials CO 2700 Manufacturing of compounds for injection molding C2505 natural color PA10T/X Low viscosity, stabilized PO 2100 Fiber composites M5000 natural color PA6I/6T Medium viscosity, amorphous with aromatic segments; CO 2700 Manufacturing of compounds for injection molding M8000 natural color PA10T/X Medium viscosity, semicrystalline with aromatic segments; partly based on renewable raw materials CO 2700 Manufacturing of compounds for injection molding Abbreviations: CO = Compounding PO = Powder Evonik Resource Efficiency GmbH VESTAMID Page 2/24
Main properties of VESTAMID base and unfilled polymers Properties Test method Unit VESTAMID M1000 M3000 C2505 2) M5000 M8000 Physical, thermal, mechanical properties, and flammability Density 23 ISO 1183 g/cm³ 1.2 1.1 1.11 1.18 1.146 Melting temperature 2 nd heating DSC ISO 11357 300-315 approx. 285 approx. 265 Softening t approx. 130 approx. 297 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 120 205 128 230 124 130 > 105 > 115 130 260 Vicat softening temperature 10 N 10 N ISO 306 300 280 295 274 Flammability acc. UL94 1.6 mm 3.2 mm IEC 60695 Water absorption 23, saturation 23, 50 rel. humidity ISO 62 8.0 0.3 3.0 0.15 3.0 0.15 Mold shrinkage in flow direction in transverse direction ISO 294-4 1.3 1.5 1.4 1.5 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 75 2 73 5 62 >100 70 >100 60 3 Tensile modulus ISO 527-1/ -2 MPa 3600 2700 2100 2700 2700 CHARPY impact strength 23-40 ISO 179/1eU 45 C 1) 40 C 1) 60 C 1) 60 C 1) N 1) >100 N 1) 300 C 1) 50 C 1) 50 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 4,5 C 1) 4 C 1) 6,4 C 1) 5,5 C 1) 18 C 1) 15 C 1) 9.5 C 1) 8 C 1) 5,5 C 1) 5,5 C 1) Electrical properties Electric strength IEC 60243-1 kv/mm 30 Volume resistivity IEC 60093 Ω cm 550 1) C = Complete break, incl. hinge break H N = No break 2) Powder, based on C2000 Evonik Resource Efficiency GmbH VESTODUR Page 3/24
Glass fiber reinforced VESTAMID PA6T/X grades VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications M10315 PA6T/X, GF15 15 glass fibers, medium viscosity, stabilized; colors: natural, black M1033 PA6T/X, GF30 30 glass fibers, medium viscosity, stabilized; colors: natural, black M10345 PA6T/X, GF45 45 glass fibers, medium viscosity, stabilized; colors: natural, black M1035 PA6T/X, GF50 50 glass fibers, medium viscosity, stabilized; colors: natural, black M1036 PA6T/X, GF60 60 glass fibers, medium viscosity, stabilized; colors: natural, black IM 7100 Dimension-stable, highly and machinery IM 11000 Dimension-stable, highly and machinery IM 15500 Dimension-stable, highly and machinery, metal replacement IM 17000 Dimension-stable, highly and machinery, metal replacement IM 23000 Dimension-stable, highly and machinery, metal replacement Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 4/24
Main properties of glass fiber reinforced VESTAMID PA6T/X grades Properties Test method Unit VESTAMID M10315 M1033 M10345 M1035 M1036 Physical, thermal, mechanical properties, and flammability Density 23 ISO 1183 g/cm³ 1.31 1.43 1.58 1.64 1.77 Melting temperature 2 nd heating DSC ISO 11357 300-315 300-315 300-315 300-315 300-315 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 280 303 290 305 292 305 293 305 293 305 Vicat softening temperature Method 10 N ISO 306 305 308 308 308 308 Linear thermal expansion 23-55 ISO 11359 10-4 K -1 7 Flammability acc. UL94 1.6 mm 3.2 mm IEC 60695 Water absorption 23, saturation 23, 50 rel. humidity ISO 62 7.2 0.3 5.6 4.4 4.0 3.2 Mold shrinkage in flow direction in transverse direction ISO 294-4 0.6 0.9 0.9 0.1 0.7 <0.1 0.5 0.6 0.9 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 110 2.0 160 1.7 210 1.7 230 1.6 260 1.5 Tensile modulus ISO 527-1/ -2 MPa 7100 11000 15500 17000 23000 CHARPY impact strength 23-40 ISO 179/1eU 19 C 1) 18 C 1) 35 C 1) 27 C 1) 54 C 1) 37 C 1) 60 C 1) 40 C 1) 60 C 1) 40 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 4 C 1) 4 C 1) 7 C 1) 7 C 1) 10 C 1) 10 C 1) 11 C 1) 11 C 1) 17 C 1) 17 C 1) Electrical properties Electric strength IEC 60243-1 kv/mm 29 28 Volume resistivity IEC 60093 Ω cm 7 x 10 15 9 x 10 15 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 5/24
Glass fiber reinforced VESTAMID PA10T/X grades VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications M30315 PA10T/X, GF15 15 glass fibers, medium viscosity, stabilized; wide processing window; green, colors: natural, black IM 5600 Dimension-stable, highly temperatures and in contact with chemicals in and machinery M3033 PA10T/X, GF30 30 glass fibers, medium viscosity, stabilized; wide processing window; green, colors: natural, black IM 9400 Dimension-stable, highly temperatures and in contact with chemicals in and machinery M3035 PA10T/X, GF50 50 glass fibers, medium viscosity, stabilized; wide processing window; green, colors: natural, black IM 15000 Dimension-stable, highly temperatures and in contact with chemicals in and machinery, metal replacement M3036 PA10T/X, GF60 60 glass fibers, medium viscosity, stabilized; wide processing window; green, colors: natural, black IM 19000 Dimension-stable, highly temperatures and in contact with chemicals in and machinery, metal replacement Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 6/24
Main properties of glass fiber reinforced VESTAMID compounds Properties Test method Unit VESTAMID M30315 M3033 M3035 M3036 Physical, thermal, mechanical properties, and flammability Density ISO 1183 g/cm³ 1.24 1.36 1.58 1.70 Melting temperature 2 nd heating DSC ISO 11357 approx. 285 approx. 285 approx. 285 approx. 285 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 248 279 >265 >285 270 284 270 282 Vicat softening temperature Method 10 N ISO 306 284 289 285 282 Linear thermal expansion 23-55 ISO 11359 10-4 K -1 0.8 Flammability acc. UL94 1.6 mm 3.2 mm IEC 60695 Water absorption 23, saturation 23, 50 rel. humidity ISO 62 2.1 0.11 1.5 0.08 1.2 0.06 Mold shrinkage in flow direction in transverse direction ISO 294-4. processing acc. ISO 1874-2 0.3 0.8 0.1 0.7 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 95 2.0 130 1.6 185 1.9 190 1.7 Tensile modulus ISO 527-1/ -2 MPa 5600 9400 15000 19000 CHARPY impact strength 23-40 ISO 179/1eU 21 C 1) 19 C 1) 40 C 1) 30 C 1) 58 C 1) 50 C 1) 60 C 1) 50 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 4 C 1) 3,5 C 1) 8,5 C 1) 8 C 1) 11 C 1) 12 C 1) 13,5 C 1) 15,5 C 1) Electrical properties Electric strength IEC 60243-1 kv/mm Volume resistivity IEC 60093 Ω cm 10 14 10 13 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 7/24
Reinforced VESTAMID grades for drinking water applications VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications M1633 PA6T/X, GF30 30 glass fibers, medium approvals for contact with drinking water; colors: natural, black M1634 PA6T/X, GF40 40 glass fibers, medium approvals for contact with drinking water; colors: natural, black M1635 PA6T/X, GF50 50 glass fibers, medium approvals for contact with drinking water; colors: natural, black M1636 PA6T/X, GF60 60 glass fibers, medium approvals for contact with drinking water; colors: natural, black IM 10000 Dimension-stable, highly and machinery, metal replacement IM 14000 Dimension-stable, highly and machinery, metal replacement IM 17000 Dimension-stable, highly and machinery, metal replacement IM 22000 Dimension-stable, highly and machinery, metal replacement Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 8/24
Main properties of reinforced VESTAMID grades for drinking water applications Properties Test method Unit VESTAMID M1633 M1634 M1635 M1636 Glass fiber content 30 40 50 60 Physical, thermal, mechanical properties, and flammability Density ISO 1183 g/cm³ 1.43 1.54 1.64 1.77 Water absorption 23, saturation 23, 50 rel. humidity ISO 62 5.6 4.8 4.0 3.2 Tensile strength 23 ISO 527 MPa 160 195 230 260 Strain at break ISO 527 1.7 1.7 1.6 1.6 Tensile modulus ISO 527-1/ -2 MPa 10000 14000 17000 22000 CHARPY impact strength 23-40 ISO 179/1eU 35 C 1) 27 C 1) 47 C 1) 34 C 1) 60 C 1) 40 C 1) 60 C 1) 40 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 7 C 1) 7 C 1) 9 C 1) 9 C 1) 11 C 1) 11 C 1) 18 C 1) 13 C 1) Temp. of deflection under load 1.8 MPa 0.45 Mpa ISO 75 290 305 290 305 293 305 293 305 Vicat softening temperature Method 10 N ISO 306 308 308 308 308 Flammability UL94 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 9/24
Reinforced VESTAMID grades for water / glycol applications VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications HY10333 PA6T/X, GF33 33 glass fibers, medium viscosity, stabilized1); colors: black HY1034 PA6T/X, GF40 40 glass fibers, medium viscosity, stabilized1); colors: black HY10345 PA6T/X, GF45 45 glass fibers, medium viscosity, stabilized 1) ; colors: black HY1035 PA6T/X, GF50 50 glass fibers, medium viscosity, stabilized1); colors: black IM 11000 Dimension-stable, highly automotives, machinery, and in contact with water / glycol IM 12000 Dimension-stable, highly automotives, machinery, and in contact with water / glycol IM 13500 Dimension-stable, highly automotives, machinery, and in contact with water / glycol IM 15600 Dimension-stable, highly automotives, machinery, and in contact with water / glycol HY3034 PA10T/X, GF40 40 glass fibers, medium viscosity, stabilized1), wide processing window, colors: black IM 11500 Dimension-stable, highly automotives, machinery, and in contact with water / glycol 1) for water / glycol contact Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 10/24
Main properties of glass fiber reinforced VESTAMID PA6T/X grades Properties Test method Unit VESTAMID HY10333 HY1034 HY10345 HY1035 HY3034 Physical, thermal, mechanical properties, and flammability Density 23 ISO 1183 g/cm³ 1.44 1.50 1.56 1.62 1.46 Melting range 2 nd heating DSC ISO 11357 295-315 295-315 300-315 300-315 approx. 286 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 286 305 290 309 292 307 293 309 270 285 Vicat softening temperature 10 N 50 N ISO 306 308 277 308 277 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 170 2.1 190 2.2 205 2 220 2 175 2.2 Tensile modulus ISO 527-1/ -2 MPa 11000 12000 13500 15600 11500 CHARPY impact strength 23-40 ISO 179/1eU 55 C 1) 40 C 1) 65 C 1) 50 C 1) 65 C 1) 60 C 1 ) 81 C 1) 77 C 1) 70 C 1) 55 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 8 C 1) 7 C 1) 9 C 1) 8 C 1) 9 C 1) 9 C 1) 13 C 1) 11 C 1) 10 C 1) 8 C 1) 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 11/24
Flame retardant VESTAMID grades VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications M1900 PA6T/X unreinforced, medium viscosity, flame retardant (UL94 V-0 from 0,4 mm), halogen free, free of red phosphorus, RoHS and WEEE conform colors: natural, black IM 4000 Parts for the electric and elec-tronics industry demanding UL94 V-0, suitable for industrial soldering. UL94 listed in file E100211. Parts fulfill RoHS 2002/95/EC, Restriction of Hazardous Substances. WEEE: Parts are not related to "selective recovery" according to Directive 2002/96/EC on waste electrical and electronic equipment. M1933 PA6T/X, GF 30 30 glass fibers, medium viscosity, flame retardant (UL94 V-0 from 0,4 mm), halogen free, free of red phosphorus, RoHS and WEEE conform colors: natural, black IM 10000 Parts for the electric and electronics industry demanding UL94 V-0, suitable for industrial soldering. UL94 listed in file E100211. Parts fulfill RoHS 2002/95/EC, Restriction of Hazardous Substances. WEEE: Parts are not related to "selective recovery" according to Directive 2002/96/EC on waste electrical and electronic equipment. Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 12/24
Main properties of flame retardant VESTAMID grades Properties Test method Unit VESTAMID M1900 M1933 Physical, thermal, mechanical properties, and flammability Density 23 ISO 1183 g/cm³ 1.22 1.46 Melting temperature 2 nd heating DSC ISO 11357 300-315 300-315 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 135 235 275 300 Vicat softening temperature 10 N 50 N ISO 306 295 235 303 Flammability acc. UL94 0.4 mm 0.8 mm IEC 60695 V-0 V-0 V-0 V-0 Water absorption 23, saturation 23, 50 rel. humidity ISO 62 5.8 3.9 Mold shrinkage in flow direction in transverse direction ISO 294-4 1.3 1.6 0.9 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 70 2.0 150 1.8 Tensile modulus ISO 527-1/ -2 MPa 4000 10000 CHARPY impact strength 23-40 ISO 179/1eU 34 C 27 C 35 C 1) 30 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 3 C 3 C 6 C 1) 6 C 1) Electrical properties Electric strength K20 / K20 IEC 60243-1 kv/mm 32 32 Comparative tracking index CTI IEC 60112 550 600 Volume resistivity IEC 60093 Ω cm 10 16 10 16 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 13/24
Rubber bondable reinforced VESTAMID grades VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications R1033 PA6T/X, GF30 30 glass fibers, medium adhesive modified for plastic-rubber composites, high heat resistance colors: black R1133 PA6T/X, GF30 30 glass fibers, medium adhesive modified for plastic-rubber composites especially with EPDM, high heat resistance colors: black R1035 PA6T/X, GF50 50 glass fibers, medium adhesive modified for plastic-rubber composites, high heat resistance colors: black IM 11000 Plastic-rubber composites (K&K): Bonding to rubber without adhesive, e.g., to ACM, FPM, H-NBR; dimension-stable, highly rigid parts for use at high service temperatures IM 10500 Plastic-rubber composites (K&K): Bonding to rubber without adhesive, especially to EPDM, AEM; dimension-stable, highly rigid parts for use at high service temperatures IM 17000 Plastic-rubber composites (K&K): Bonding to rubber without adhesive, e.g., to ACM, FPM, H-NBR; dimension-stable, highly rigid parts for use at high service temperatures Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 14/24
Main properties of rubber bondable reinforced VESTAMID grades Properties Test method Unit VESTAMID R1033 R1133 R1035 Physical, thermal, mechanical properties, and flammability Density 23 ISO 1183 g/cm³ 1.43 1.40 1.64 Melting temperature 2 nd heating DSC ISO 11357 300-315 300-315 300-315 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 290 305 270 295 290 305 Vicat softening temperature Method 10 N ISO 306 305 300 305 Flammability acc. UL94 1.6 mm 3.2 mm IEC 60695 Water absorption 23, saturation 23, 50 rel. humidity ISO 62 5.6 5.0 4.0 Mold shrinkage in flow direction in transverse direction ISO 294-4 0.9 0.9 0.1 0.7 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 180 2 140 1.5 240 2 Tensile modulus ISO 527-1/ -2 MPa 11000 10500 17000 CHARPY impact strength 23-40 ISO 179/1eU 45 C 1) 30 C 1) 29 C 1) 23 C 1) 70 C 1) 50 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 7 C 1) 7 C 1) 6 C 1) 6 C 1) 11 C 1) 11 C 1) 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 15/24
Tribological modified VESTAMID grades VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications M1533 PA6T/X, GF30 30 glass fibers, medium lubricated, low wear, colors: natural, black IM 10500 Tribological loaded parts at high service temperatures, e.g. sliding bearings, pivot bushings, bearing cups, slide rails, sliding parts Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 16/24
Main properties of tribological modified VESTAMID grades Properties Test method Unit VESTAMID M1533 Density 23 ISO 1183 g/cm³ 1.54 Melting temperature 2 nd heating DSC ISO 11357 300-315 Temp. of deflection under load 1.8 MPa ISO 75 290 Flammability acc. UL94 1.6 mm 3.2 mm IEC 60695 Water absorption 23, saturation 23, 50 rel. humidity ISO 62 Mold shrinkage in flow direction in transverse direction ISO 294-4 0,0 0,6 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 160 1.7 Tensile modulus ISO 527-1/ -2 MPa 10500 CHARPY impact strength 23 ISO 179/1eU 35 C 1) CHARPY notched impact strength 23 ISO 179/1eA 10 C 1) 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 17/24
Mineral reinforced VESTAMID grades VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications M10525 M1054 PA6T/X, MD25 25 mineral, medium anisotropic, colors: black PA6T/X, MD40 40 mineral, medium anisotropic, colors: black IM 8600 Dimension-stable, anisotropic technical parts for the and machinery, glossy surface IM 12800 Dimension-stable, anisotropic technical parts for the and machinery, glossy surface M10465 PA6T/X, GMD65 65 mineral and glass fiber, medium viscosity, stabilized, anisotropic, colors: black IM 20800 Dimension-stable, highly rigid and anisotropic technical parts for the use at high service and machiner Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 18/24
Main properties of mineral reinforced VESTAMID grades Properties Test method Unit VESTAMID M10525 M1054 M10465 Physical, thermal, mechanical properties, and flammability Density 23 ISO 1183 g/cm³ 1.41 1.57 1.89 Melting temperature 2 nd heating DSC ISO 11357 300-315 300-315 300-315 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 220 287 240 290 290 307 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 133 2.4 148 1.9 190 1.2 Tensile modulus ISO 527-1/ -2 MPa 8600 12800 20800 CHARPY impact strength 23-40 ISO 179/1eU 34 C 1) 30 C 1) 52 C 1) 37 C 1) 40 C 1) 35 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 3.6 C 1) 2.6 C 1) 3.7 C 1) 3.1 C 1) 5.5 C 1) 5.0 C 1) 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 19/24
Carbon fiber reinforced VESTAMID grades VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications M1063 PA6T/X, CF30 30 carbon fibers, medium antistatic, low wear, conductive; colors: black IM 24000 Dimension-stable, exhibiting high stiffness, highly rigid technical parts for the and machinery Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 20/24
Main properties of carbon fiber reinforced VESTAMID grades Properties Test method Unit VESTAMID M1063 Density 23 ISO 1183 g/cm³ 1.32 Melting temperature 2 nd heating DSC ISO 11357 300-315 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 305 282 Vicat softening temperature Method 10 N ISO 306 Flammability acc. UL94 1.6 mm 3.2 mm IEC 60695 Water absorption 23, saturation 23, 50 rel. humidity ISO 62 Mold shrinkage in flow direction in transverse direction ISO 294-4 0,08 0,43 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 240 1.2 Tensile modulus ISO 527-1/ -2 MPa 24000 CHARPY impact strength 23-40 ISO 179/1eU 45 C 1) 40 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 7 C 1) 6.5 C 1) Electrical properties Surface resistance ROA IEC60093 Ohm 1000 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 21/24
VESTAMID grades for Laser Direct Structuring (LDS) VESTAMID Description acc. ISO 1874-1 Characterization Processing Tensile modulus [MPa] Applications LDS1031 PA6T/X, GF10 10 glass fibers, mineral reinforced, medium qualified for LPKF LDS process, optimized shrinkage, suitable for lead-free solders IM 11500 Three-dimensional interconnect devices in electronical applications, specially adapted for the LDS process. Dimensionstable, glossy surface LDS3031 PA10T/X, GF10 10 glass fibers, mineral reinforced, medium qualified for LPKF LDS process, optimized shrinkage, suitable for lead-free solders. Partly biobased and eco-friendly IM 9500 Three-dimensional interconnect devices in electronical applications, specially adapted for the LDS process. Dimensionstable, glossy surface Abbreviations: IM = Injection molding Evonik Resource Efficiency GmbH VESTAMID Page 22/24
Main properties of VESTAMID grades for Laser Direct Structuring Properties Test method Unit VESTAMID LDS1031 LDS3031 Physical, thermal, mechanical properties, and flammability Density 23 ISO 1183 g/cm³ 1.62 1.53 Melting temperature 2 nd heating DSC ISO 11357 300-315 approx.. 285 Temp. of deflection under load 1.8 MPa 0.45 MPa ISO 75 272 286 259 285 Vicat softening temperature 10 N 50 N ISO 306 302 260 279 243 Flammability acc. UL94 0.4 mm 0.8 mm IEC 60695 no classification no classification Water absorption 23, saturation 23, 50 rel. humidity ISO 62 Mold shrinkage in flow direction in transverse direction ISO 294-4 0.35 0.53 7 0.54 Tensile test Stress at break Strain at break ISO 527-1/ -2 MPa 80 0.8 84 1.1 Tensile modulus ISO 527-1/ -2 MPa 11500 9500 CHARPY impact strength 23-40 ISO 179/1eU 13 C 1) 10 C 1) 15 C 1) 12 C 1) CHARPY notched impact strength 23-40 ISO 179/1eA 1.8 C 1) 1.8 C 1) 2.3 C 1) 2.2 C 1) Electrical properties Electric strength K20 / P50 IEC 60243-1 kv/mm Comparative tracking index CTI IEC 60112 600 - <1 600 - <1 Volume resistivity pd IEC 60093 Ω cm 1.41 E+16 7.79 E+15 1) C = Complete break, incl. hinge break H Evonik Resource Efficiency GmbH VESTODUR Page 23/24
Integrated expertise: direct contacts in every region Contact Country Phone Mobile E-mail Karsten Goldstein Scandinavia +49 2362 999797 +49 171 813 0033 karsten.goldstein@evonik.com Frank Lindner Germany +49 2365 6990758 +49 171 813 0045 frank.lindner@evonik.com Prafulla Toke Andrzej Wolak Austria, Switzerland Czech. Republic, Poland, Slovakia +49 172 4095686 prafulla.toke@evonik.com +48 22 318 1007 +48 60 320 2152 andrzej.wolak@evonik.com Géraud Apchin France +33 1 39 75 79 85 +33 607 24 4714 geraud.apchin@evonik.com Luca Castelli Roberto Sacchi Italy, Spain +39 010 8601925 +39 0371 21 9363 +39 393 1924645 +39 335 684 0731 luca.castelli@evonik.com roberto.sacchi@evonik.com Julia Trufanova Russia +7 495 721 2862 (ext. 566) julia.trufanova@evonik.com Cigdem Kir Turkey +90 2163 959 961 +90 530 280 93 52 cigdem.kir@evonik.com Karel Ogenia UK, Eire, Nordic +31 492 772210 +31 6 51245557 karel.ogenia@evonik.com Peter Colburn USA, Canada +1 203 284 4291 peter.colburn@evonik.com Miguel A. Delgado Mexico +52 55 5483 1023 +52 55 2980 8891 miguel.delgado@evonik.com Haroldo Rodrigues South America +55 11 3146 4150 +55 11 8700 0532 haroldo.rodrigues@evonik.com Sandra Kao Taiwan +88 622175 5259 +88 6955 63 2323 sandra.kao@evonik.com Stanford Tang China +86 21 6119 1402 +86 138 18547434 stanford.tang@evonik.com Hitesh Shah India +91 22 6723 8851 +91 98197 13881 hitesh.shah@evonik.com Mitsunori Naganuma Japan +81 3 5324 6332 +81 90 6122 9653 m.naganuma@daicel-evonik.com David Baek Joonsang Park Korea +82 2 320 4750 +82 325102431 +82 1098830181 david.baek@evonik.com joonsang.park@evonik.com Andrew Windsor Australia +61 3 9703-8889 +61 41 9517 180 sharad.gune@evonik.com VESTAMID is a registered trademark of the Evonik Degussa GmbH This information and any recommendations, technical or otherwise, are presented in good faith and believed to be correct as of the date prepared. Recipients of this information and recommendations must make their own determination as to its suitability for their purposes. In no event shall Evonik assume liability for damages or losses of any kind or nature that result from the use of or reliance upon this information and recommendations. EVONIK EXPRESSLY DISCLAIMS ANY REPRESENTATIONS AND WARRANTIES OF ANY KIND, WHETHER EXPRESS OR IMPLIED, AS TO THE ACCURACY, COMPLETENESS, NON-INFRINGEMENT, MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE (EVEN IF EVONIK IS AWARE OF SUCH PURPOSE) WITH RESPECT TO ANY INFORMATION AND RECOMMENDATIONS PROVIDED. Reference to any trade names used by other companies is neither a recommendation nor an endorsement of the corresponding product, and does not imply that similar products could not be used. Evonik reserves the right to make any changes to the information and/or recommendations at any time, without prior or subsequent notice. Evonik Resource Efficiency GmbH High Performance Polymers, 45764 Marl Phone +49 2365 49-9878, E-mail evonik-hp@evonik.com www.vestamid.com