1 Product and Company Identification Product name: Material identification: Gurit PVC ; Gurit PVC HT Application of the product: Structural rigid foam Supplier: Gurit Americas Inc. Gurit (USA) Inc. 175, rue Péladeau 115 Broadcommon Road Magog (Québec) J1X 5G9 Bristol, Rhode Island 02809 Canada Tel: 819-847-2182 USA Tel: 401-396-5008 For additional information: Health, Safety and Environment department: Email: regulatory@gurit.com 2 Hazards Identification Emergency overview: Solid combustible material. Hazardous designation: This material is not classified as a hazardous product. This material is defined as a manufactured article and, as such, is exempt from HCS or CPR regulations. Potential health effects: Eyes: Dust from machining operations on the product may cause irritation. Skin: Mechanical abrasion may cause minor irritation. Inhalation: Dust and vapors released from machining operations may cause respiratory tract irritation. Ingestion: Product is not expected to present harmful effects if swallowed. 3 Composition/Information on Ingredients Chemical Characterization: Rigid foam consisting of semi interpenetrating network between Polyvinyl Chloride and aromatic polyureas. Blowing agents: Nitrogen (N 2 ) and Carbon dioxide (CO 2 ). Page 1 of 5
4 First Aid Measures Eye contact: Skin contact: Ingestion: Inhalation: If dust or particles become lodged in eyes, rinse immediately with plenty of water. if symptoms persist, consult a physician. No need for specific measures. In case of persistent symptoms, consult a physician. If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain medical attention. 5 Fire-Fighting Measures Suitable extinguishing media: Special exposure hazards: Protective equipment: Water, foam, carbon dioxide or dry chemical fire extinguishers. Formation of toxic gases will occur during a fire. Combustion byproducts include but are not limited to carbon monoxide, carbon dioxide, hydrogen chloride and hydrogen cyanide.. Wear fully protective suit with self contained breathing apparatus (SCBA) with a face-piece operated in positive pressure mode. 6 Accidental Release Measures No special measures required 7 Handling and Storage Handling: Wear appropriate personal protection when handling. Machining operations which can produce dust should be properly fitted to a dust collection system. Prevent formation of dust that could create explosive atmospheres. Accumulation of static electricity charges may appear during machining operations or handling of the material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up. Static electricity from the material might give an unpleasant sensation but is not a possible source of ignition. Storage: Protect from open flames. This product is a combustible material and should be stored according to the national or local Fire Code. Page 2 of 5
8 Exposure Controls / Personal Protection Exposure limits : Ingredient name CAS# OSHA (PEL) ACGIH Particulates Not otherwise Regulated - 15 mg/m 3 (TWA) 10 mg/m 3 (TLV) Note: Dust from machining operations has non-respirable fraction properties. Engineering measures: Personal protection equipments: Eye protection: Skin protection: Respiratory protection: Provide general and local exhaust ventilation to control airborne contaminant. Wear safety glasses/goggles Wear general purpose gloves and protective work clothing. Wear an approved respirator with organic vapour cartridge if ventilation is not adequate. Breathing protection recommended if excessive dust is generated. General measures: Handle product with good industrial and safety practices. 9 Physical and Chemical Properties Physical state: Solid Color: Varied Odor: Nearly odorless Flash point: Melting point: Not established Decomposition temperature: > 220 o C Density: 30 400 kg/m 3 Solubility in water: Insoluble Page 3 of 5
10 Stability and Reactivity Stability and reactivity: Conditions to avoid: Dangerous reaction: Hazardous decomposition products: This product is stable. Do not overheat to avoid thermal decomposition. No dangerous reactions known. Decomposition products include but are not limited to carbon monoxide, carbon dioxide, hydrogen chloride and hydrogen cyanide. 11 Toxicological Information Toxicological data: Not available Acute effects: Eyes: Dust may cause irritation to eyes. Skin: Abrasive contact may cause minor irritation to skin. Inhalation: Dust and vapor may cause respiratory tract irritation. Chronic effects Sensitization: No sensitizing effects known. Mutagenic effects: Not available Teratogenic effects: Not available Reproduction effects: Not available Carcinogenic effects: Not listed by IARP, NTP, OSHA, EU, ACGIH Additional information: When used and handled according to specifications, the product is not expected to cause any adverse effects. 12 Ecological Information Ecotoxicity data: No data available Persistence and biodegradability: No data available Mobility: Foam particles will float on the water. 13 Disposal Consideration Waste disposal: Product is stable and not hazardous. Waste generator should review local regulations. Toxic gases will be generated if waste product is incinerated. Page 4 of 5
14 Transport Information Regulatory status (UN; IMDG/IATA; DOT/TDG): Not regulated for transport 15 Regulatory Information Regulatory status: This core material is defined as a manufactured article and, as such, is exempt from HCS or CPR regulations. TSCA (USA) & DSL (CAN): All substances are listed U.S. State regulations: WHMIS classification: California Proposition 65: No substance listed 16 Other Information References: ANSI Z400.1, MSDS Standard, 2004; 29CFR 1910.1200 OSHA Hazard Communication Standard; Controlled Products Regulations (DORS/88-66) Canada. Notice to the reader: To the best of our knowledge, the information contained herein is accurate at the date of its publication. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. Page 5 of 5