ARBN 26 008 776 243 PRODUCT INDEX TRAFFIC PAINTS 1. Waterbased Road Marking 201 White 2. Waterbased Road Marking 301 HD White 3. Waterbased Road Marking 401 HD White 4. Waterbased Road Marking RF6040 White 5. Thermoplastic Road Marking Material Thermomark Profile Grade White 6. Thermoplastic High Performance, Road Marking Material - Thermomark - Profile Grade 7. Thermoplastic Road Marking Material Thermomark Extrusion Grade White 8. Thermoplastic High Performance, Road Marking Material - Thermomark - Extrusion Grade 9. Thermoplastic Road Marking Material - Thermomark - Preformed Grade - White 10. Thermoplastic Road Marking Material Spray Application 11. Plasticote Cold Applied Plastic 12. Line Removal Mastic RM 601 May 2014 Version 4.0
ARBN 26 008 776 243 Product Description PRODUCT DATA SHEET Waterbased Road Marking 201 White A high quality, single component water borne solvent free, non toxic road marking paint that dries within 5 minutes, as tested to Australian Standard Test Method AS 1580.401.8. This pure acrylic paint is very hard wearing, with excellent anti-skin properties. The product complies with the requirements of APAS 0041/5 as well as the Australian Standard 4049.3:2005. Product Code SR 201/01 Product Uses A flat, durable, traffic marking paint suitable for use on bitumen, concrete, chipseal and over previous coatings. Surface Preparation Surfaces must be clean, free of surface contaminants and dry. Blow down to ensure removal of loose particles and dust. Use a broom to sweep away leaves and other contaminants. Application Apply by spray direct from the can, and using pedestrian line marking machines, or mobile, truck mounted airless spray units. Notes and Limitations Guidance on use and Application in A.S.4049.3-2005 (Appendix B ). You may request a copy of the relevant appendix from Supalux. Recommended Minimum Conditions for Satisfactory Performance are: a) Air Temperature and pavement temperature should be > 20degC b) Relative Humidity < 70% c) Wind Speed > 10kph. May 2014 Version 4.0
Safety Precautions Refer to the relevant Material Safety Data Sheet (MSDS) Ref SR201MS. Technical Information Colour White. Finish Flat. Volume Solids 62 plus/minus 1%. Flash Point Not applicable. Recommended Application Data Application method: Thinner/Cleaner: W.F.T per coat: D.F.T per coat: Airless, Conventional Spray Water. 375 400 microns. 235 250 microns. Practical Coverage @ 200 microns DFT (allow appropriate loss factor): 3.1 square metres/litre. Drying Time @ 25 C Touch Dry: 5 minutes. Hard Dry: 15 minutes. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. May 2014 Version 4.0
ARBN 26 008 776 243 PRODUCT DATA SHEET Waterbased Road Marking 301 High Build White Product Description A high quality water borne non hazardous road marking paint that dries within 5 minutes, as tested to Australian Standard Test Method AS 1580.401.8. This pure acrylic paint is very hard wearing, with excellent anti-skin properties. Supalux Waterbased Road Marking 301 High Build traffic paint is one of the most durable and reflective waterborne traffic paint systems available. Unlike standard traffic paints, 301 High Build utilizes an acrylic cross-linking emulsion that allows for applications of up to 650 microns wet film build. When cured, 301 High Build remains flexible providing superior durability with varying temperature conditions. 301 High Build s thicker application enables the use of larger glass beads which can improve retro reflectivity. 301 High Build can be applied through virtually all airless spray units. (refer to manufacturer s recommendations). Specifications Met: Australian Standard AS 4049.3:2005 Australian Paint Approval Scheme APAS 0041/5 Product Code SR301/01 Product Uses A flat, durable high build traffic marking paint suitable for use on bitumen, concrete, chipseal and over previous coatings, designed to provide longer term retro reflectivity with a wide range of glass spheres. Surface Preparation Surfaces must be clean, free of surface contaminants and dry. Blow down to ensure removal of loose particles and dust. Use a broom to sweep away leaves and other contaminants. Application Apply by spray direct from the can, and using pedestrian line marking machines, or mobile, truck mounted airless spray units. May 2014 Version 3.0
Notes and Limitations Guidance on use and Application in A.S.4049.3-2005 (Appendix B ). You may request a copy of the relevant appendix from Supalux. Recommended Minimum Conditions for Satisfactory Performance are: a) Air Temperature and pavement temperature should be > 20degC b) Relative Humidity < 70% c) Wind Speed > 10kph. Safety Precautions Refer to the relevant Material Safety Data Sheet for WATERBASED ROADMARKING 301 HD WHITE. Technical Information Colour White. Finish Flat. Flash Point Not applicable. Recommended Application Data Application method: Thinner/Cleaner: W.F.T per coat: D.F.T per coat: Airless, Conventional Spray Water. 300 650 microns. 186 400 microns. Practical Coverage @ 300 microns DFT (allow appropriate loss factor): 2.06 square metres/litre. Allow appropriate losses in application. Drying Time @ 25 C Touch Dry: Hard Dry: 5 minutes. 15 minutes. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. May 2014 Version 3.0
ARBN 26 008 776 243 PRODUCT DATA SHEET Waterbased Road Marking 401 High Reflectivity, White Product Description A high quality water borne non hazardous road marking paint that dries within 5 minutes, as tested to Australian Standard Test Method AS 1580.401.8. This pure acrylic paint is very fast curing, with excellent wear characteristics and glass bead retention. Supalux Waterbased Road Marking 401 High Build traffic paint is a super fast drying, durable and reflective waterborne traffic paint. Unlike standard traffic paints, 401 HR utilizes a highly specialised acrylic cross-linking emulsion that allows for applications of up to 800 microns wet film build. When cured, 401 HR remains flexible providing superior durability with varying temperature conditions. 401 HR has inbuilt adhesion promotion qualities for retention of retroreflective glass beads. Thicker application enables the use of larger glass beads which can improve retro reflectivity. 401 HR can be applied through virtually all airless spray units. (refer to manufacturer s recommendations). Specifications Met: Australian Standard AS 4049.3:2005 Australian Paint Approval Scheme APAS 0041/5 Product Code SR401/01 Product Uses A flat, durable, high build traffic marking paint suitable for use on bitumen, concrete, chipseal and over previous coatings, designed to provide longer term retro reflectivity with a wide range of glass spheres. April 2014 Version 2.0
Surface Preparation Surfaces must be clean, free of surface contaminants and dry. Blow down to ensure removal of loose particles and dust. Use a broom to sweep away leaves and other contaminants. Application Apply by spray direct from the can, and using pedestrian line marking machines, or mobile, truck mounted airless spray units. Notes and Limitations Guidance on use and Application in A.S.4049.3-2005 (Appendix B ). You may request a copy of the relevant appendix from Supalux. Recommended Minimum Conditions for Satisfactory Performance are: a) Air Temperature and pavement temperature should be > 20degC b) Relative Humidity < 70% c) Wind Speed > 10kph. Safety Precautions Refer to the relevant Material Safety Data Sheet for WATERBASED ROADMARKING 401 HR WHITE. Technical Information Colour White. Finish Flat. Flash Point Not applicable. Recommended Application Data Application method: Airless, Conventional Spray Thinner/Cleaner: Water. W.F.T per coat: 300 800 microns. D.F.T per coat: 186 496 microns. Practical Coverage @ 400 microns DFT (allow appropriate loss factor): 1.55 square metres/litre. Drying Time @ 25 C Touch Dry: <5 minutes. Hard Dry: < 15 minutes. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. April 2014 Version 2.0
ARBN 26 008 776 243 Product Description PRODUCT DATA SHEET Waterbased Road Marking RF6040 White A high quality, single component water borne solvent free, non toxic road marking paint that dries within 5 minutes, as tested to Australian Standard Test Method AS 1580.401.8. This pure acrylic paint is very hard wearing, with excellent anti-skin properties. The product complies with the requirements of APAS 0041/5 as well as the Australian Standard 4049.3:2005. Product Uses A flat, durable, traffic marking paint suitable for use on bitumen, concrete, chipseal and over previous coatings. Surface Preparation Surfaces must be clean, free of surface contaminants and dry. Blow down to ensure removal of loose particles and dust. Use a broom to sweep away leaves and other contaminants. Application Apply by spray direct from the can, and using pedestrian line marking machines, or mobile, truck mounted airless spray units. Notes and Limitations Guidance on use and Application in A.S.4049.3-2005 (Appendix B ). You may request a copy of the relevant appendix from Supalux. Recommended Minimum Conditions for Satisfactory Performance are: a) Air Temperature and pavement temperature should be > 20degC b) Relative Humidity < 70% c) Wind Speed > 10kph. April 2014 Version 2.0
Safety Precautions Refer to the relevant Material Safety Data Sheet (MSDS) Ref SR103MS. Technical Information Colour White, Yellow and Black only. Finish Flat. Volume Solids 62 plus/minus 1%. Flash Point Not applicable. Recommended Application Data Application method: Thinner/Cleaner: W.F.T per coat: D.F.T per coat: Airless, Conventional Spray Water. 375 400 microns. 235 250 microns. Practical Coverage @ 200 microns DFT (allow appropriate loss factor): 3.1 square metres/litre. Drying Time @ 25 C Touch Dry: 5 minutes. Hard Dry: 15 minutes. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months May 2014 Version 3.0
ARBN 26 008 776 243 PRODUCT DATA SHEET Thermoplastic Road Marking Material Thermomark Profile Grade White Product Description High quality white, granulated, hot melt, material. It is applied to the road surface in molten form. This product provides a long lasting, highly visible road marking. This product is a safety product, which produces an audible warning to motorists when trafficked upon. Specifications met: - Australian Standard AS/NZS 4049.2:2005 and RTA 3357, APAS 0041/4 Product use This product is intended for use as a long life, audible, tactile shape, between 5 to 9 mm profile height. Application Apply directly to a bitumen road surface. Equipment should be designed specifically for this purpose. Refer the manufacturers for further information on suitable equipment. Concrete surfaces must be pre treated with a Tack coat. All surfaces must be clean and dry before application Application method Apply by truck mounted or self propelled pressurised vessel or auger fed extruder Application conditions Apply at when product is between 180 o C and 200 o C. Do not heat above 230 o C. Do not apply when the product temperature is below 175 o C. May 2014 Version 2.0
Technical Information Colour Luminance factor Softening Point Loss (L/F) Skid Resistance (BPN) Flow Resistance Gradation of mineral content Glass bead content Abrasion resistance Flash Point Density White 80 minimum 85 o C minimum 5% maximum 55 minimum 2% maximum 20% (W/W) minimum 20% minimum 0.6g/100 revolutions maximum 230 o C minimum 1.9-2.2 Kg/L Packaging Supplied in 25Kg convenient, meltable bags (no need to remove from bag). Safety Precautions Refer to the relevant Supalux Material Safety Data Sheet. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. May 2014 Version 2.0
ARBN 26 008 776 243 PRODUCT DATA SHEET High Performance, Thermoplastic Road Marking Material Thermomark Profile Grade White Product Description A new generation, high quality white, granulated, hot melt material. It is applied to the road surface in molten form. This product provides a long lasting, highly visible road marking. This product is a safety product, which produces an audible warning to motorists when trafficked upon. This product is capable of up to 10mm profile height and therefore is excellent for wet weather delineation of traffic markings This High Performance Thermoplastic product is manufactured with the highest quality ingredients including titanium dioxide and larger, wet weather, retro reflective, glass beads. It therefore provides the ultimate in long term performance. Specifications met: - Australian Standard AS/NZS 4049.2:2005 and RTA 3357 Product use This product is intended for use as a long life, audible, tactile shape, between 7 to 10 mm profile height. Application Apply directly to a bitumen road surface. Equipment should be designed specifically for this purpose. Refer the manufacturers for further information on suitable equipment. Concrete surfaces must be pre treated with a tack coat. All surfaces must be clean and dry before application. April 2014 Version 1.0
Application method Apply by truck mounted, self propelled pressurised vessel or auger fed extruder. Application conditions Apply at when product is between 180 o C and 200 o C. Do not heat above 230 o C. Do not apply when the product temperature is below 175 o C. Technical Information Colour Luminance factor Softening Point Loss (L/F) Skid Resistance (BPN) Flow Resistance Gradation of mineral content Glass bead content Abrasion resistance Flash Point Density White 80 minimum 85 o C minimum 5% maximum 55 minimum 2% maximum 20% (W/W) minimum 30% minimum 0.6g/100 revolutions maximum 230 o C minimum 1.9-2.2 Kg/L Packaging Supplied in 25Kg convenient, meltable bags (no need to remove from bag). Safety Precautions Refer to the relevant Supalux Material Safety Data Sheet. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. April 2014 Version 1.0
ARBN 26 008 776 243 PRODUCT DATA SHEET Thermoplastic Road Marking Material Thermomark Extrusion Grade White Product Description A high quality, white, granulated, hot melt, material. It is applied to the road surface in molten form. This product provides a long lasting, highly visible road marking. Specifications met :- Australian Standard AS/NZS 4049.2:2005 and RTA 3357, APAS 0041/4 Product use This product is intended for use as a long life pavement marking. Applied at between 1.5 2.5mm as specified. Theoretical Coverage at 1mm,0.5sqm/kg. Application Ensure surface is clean, dry and dust free. Apply directly to a bitumen road surface. Application method Apply by truck mounted or self propelled pressurised vessel or auger fed extruder. TACK COAT is recommended when applying on concrete surfaces. Please refer to manufacturers in this regard. Application conditions Apply at when product is between 180 o C and 200 o C. Do not heat above 230 o C. Do not apply when the product temperature is below 175 o C. May 2014 Version 2.0
Technical Information Colour Luminance factor Softening Point Loss (L/F) Skid Resistance (BPN) Flow Resistance Gradation of mineral content Glass bead content Abrasion resistance Flash Point Density White 75 minimum 90 o C minimum 5% maximum 55 minimum 10% maximum 20% (W/W) minimum 20% minimum 0.6g/100 revolutions maximum 230 o C minimum 1.9-2.2 Kg/L Packaging Supplied in 25Kg convenient, meltable bags (no need to remove from bag). Safety Precautions Refer to the relevant Supalux Material Safety Data Sheet. Extrusion Grade Thermoplastic white should not be applied to concrete without the use of a tack coat. Refer to manufacturer for further details. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months May 2014 Version 2.0
ABN 26 008 776 243 PRODUCT DATA SHEET High Performance, Thermoplastic Road Marking Material Thermomark Extrusion Grade White Product Description This is a new generation, high performance, extrusion grade of Thermoplastic. It is the ultimate in high quality, white, granulated, hot melt, material. It is applied to the road surface in molten form. This product provides a long lasting, highly visible road marking. This high performance thermoplastic product is manufactured with the highest quality ingredients including titanium dioxide and larger, wet weather, retro reflective, glass beads. It therefore provides the ultimate in long term performance and high retro reflectivity. Specifications met :- Australian Standard AS/NZS 4049.2:2005 and RTA 3357, APAS 0041/4 Product use This product is intended for use as a long life, high retro reflectivity, pavement marking. Applied at between 1.5 2.5mm as specified. Theoretical Coverage at 1mm is 0.5m 2 /kg. Application Ensure surface is clean, dry and dust free. Apply directly to a bitumen road surface. Application method Apply by truck mounted or self propelled pressurised vessel or auger fed extruder. Tack coat is recommended when applying on concrete surfaces. Please refer to manufacturers in this regard. April 2014 Version 1.0
Application conditions Apply at when product is between 180 o C and 200 o C. Do not heat above 230 o C. Do not apply when the product temperature is below 175 o C. Technical Information Colour White Luminance factor 75 minimum Softening Point 90 o C minimum Loss (L/F) 5% maximum Skid Resistance (BPN) 55 minimum Flow Resistance 10% maximum Gradation of mineral content 20% (W/W) minimum Glass bead content 30% minimum Abrasion resistance 0.6g/100 revolutions maximum Flash Point 230 o C minimum Density 1.9-2.2 Kg/L Packaging Supplied in 25Kg convenient, meltable bags (no need to remove from bag). Safety Precautions Refer to the relevant Supalux Material Safety Data Sheet. Extrusion Grade Thermoplastic white should not be applied to concrete without the use of a tack coat. Refer to manufacturer for further details. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. April 2014 Version 1.0
ARBN 26 008 776 243 PRODUCT DATA SHEET Thermoplastic Road Marking Material Thermomark Preformed Grade White Product Description Thermomark Preformed is supplied is easy to use sheet form It is a durable thermoplastic pavement marking used for symbols, transverse markings and legends, horizontal signs, and advanced warning and traffic calming. Supalux has engineered this product to perform in various road and weather conditions. It is an ideal road safety solution for school zones, crosswalks, intersections and any location where long term performance, high retro reflectivity and visibility is critical. Specifications met :- Australian Standard AS/NZS 4049.2:2005 and RTA 3357. Product use This product is intended for use as a long life pavement marking supplied ready for use at between 1.5 2.5mm thickness pre formed shapes as specified. Application method Surface must be clean and dry. Lay out on a bitumen road surface and apply gentle flame / gas burner to melt the supplied preformed sheet onto the road surface. Precautions must be taken not to burn and discolour the material. Retro reflective glass spheres are usually broadcast immediately onto the softened surface for initial, additional, retro reflectivity. A TACK COAT is recommended when applying on concrete surfaces. Please refer to manufacturers in this regard. May 2014 Version 2.0
Technical Information Colour Luminance factor Softening Point Loss (L/F) Skid Resistance (BPN) Flow Resistance Gradation of mineral content Glass bead content Abrasion resistance Flash Point Density White 75 minimum 80 o C minimum 5% maximum 55 minimum 10% maximum 20% (W/W) minimum 20% minimum 0.6g/100 revolutions maximum 230 o C minimum 1.9-2.2 Kg/L Safety Precautions Refer to the relevant Supalux Material Safety Data Sheet. Preformed - White should not be applied to concrete without the use of a tack coat. Refer to manufacturer for further details. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. May 2014 Version 2.0
ARBN 26 008 776 243 PRODUCT DATA SHEET Thermoplastic Road Marking Material Spray Application Product Description A white, granulated, high quality formulation, that when melted, can be spray applied to a road surface to produce a long life, highly visible, reflective road paint. This product complies with Australian Standard AS/NZS 4049.2:2005 and RTA 3357 Product use This product is intended for use as a long life pavement marking and may be applied at film builds between 750 micrometers to 2.5mm Dry build. Coverage Theoretical coverage 0.66m 2 per Kg. Application Ensure the surface is clean and dry and dust free. Apply directly to a bitumen road surface.. Application method Apply by truck mounted or self propelled pressurised spray unit. TACK COAT is recommended in all applications on concrete. Please refer to manufacturers in this regard. Application conditions Apply at when product is between 180 o C and 200 o C. Do not heat above 230 o C. Do not apply when the product temperature is below 175 o C. May 2014 Version 2.0
Technical Information Colour Luminance factor Softening Point Loss (L/F) Skid Resistance (BPN) Flow Resistance Gradation of mineral content Glass bead content Abrasion resistance Flash Point Density White 75 minimum 90 o C minimum 5% maximum 55 minimum 10% maximum 20% (W/W) minimum 20% minimum 0.6g/100 revolutions maximum 230 o C minimum 1.9-2.2 Kg/L Packaging Supplied in 25Kg convenient, meltable bags (no need to remove from bag). Safety Precautions Refer to the relevant Supalux Material Safety Data Sheet. Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. May 2014 Version 2.0
ARBN 26 008 776 243 PRODUCT DATA SHEET Plasticote Cold Applied Plastic Long life road paint Product Description Plasticote is based on proven methyl methacrylate (MMA) technology. MMA is the most durable pavement marking material available anywhere today. Plasticote may be applied as a structured finish, traffic marking system designed for application via a splatter pattern technique. (Specialised equipment is required for this application.) Refer Supalux for details and availability. When the structured finish is applied over a new or bare pavement surface, it creates a solid line effect when viewed by the driver. Additionally, the structured design produces enhanced wet night retro-reflectivity by allowing water to flow off its peaks and valleys. It is applied at approx 1.5-2mm structure height. Features and Recommended uses Plasticote is very resistant to mechanical damage. It is abrasion resistant and therefore very hard wearing. It retains retro reflective glass spheres with a chemical bond of exceptional strength. Plasticote can be screed applied, profiled, extruded, and sprayed at various film thicknesses ranging from 0.5mm to 2mm. It may be applied onto asphalt or concrete roads for both long line as well as transverse markings. General Data Specific Gravity: 1.7 Supplied in: 18Kg pail & 180Kg drums 90% Volume Solids Colour : White, Charcoal, Yellow Curing Time : 10-15 mintues @ 25 degc Trafficable in 20 minutes May 2014 Version 2.0
Application Spray, roller, trowel or specialised equipment for specialised finishes. Coverage Rate Practical coverage @2mm is 0.45m 2 /L 0.26m 2 /Kg or 4.48m 2 per 18Kg pail Thinner Not recommended Clean Up Special Thinners for Plasticote Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. May 2014 Version 2.0
ARBN 26 008 776 243 PRODUCT DATA SHEET Water based High Durability Line Removal Mastic RM601 Product Description A new development in line removal. Line Removal Mastic RM 601 water borne road line mastic meets all the requirements of flexibility, obliteration and durability. A long lasting solution to line removal and reinstatement. This acrylic mastic is very hard wearing and has a rubberized finish with excellent resilient qualities. It can be matched to the existing road surface and has aesthetic appeal. Road trials have proven the superior wear characteristics of this new generation product. RM 601 utilizes a specialised acrylic emulsion that allows for fast curing applications of up to 800 microns wet film build. When cured, RM601 remains flexible and can be applied through virtually all-airless spray truck mounted units. Product Uses Long life obliteration of traffic markings. Reinstatement of new lines and relocation of pavement markings. Surface Preparation Surfaces must be clean, free of surface contaminants and dry. Blow down to ensure removal of loose particles and dust. Use a broom to sweep away leaves and other contaminants. Application Recommended for application by airless spray, computer monitored, truck mounted equipment. For additional Non-Skid qualities on smooth seals, we recommend the broadcasting of iron titanium oxide aggregate (iilmenite) @ 500gm/m 2. Volume solids: 65+-3% Disclaimer The manufacturer warrants that its products have been manufactured under strict control and conforms to its highest standards. The performance of the product will vary according to the nature of the surface to which it is applied and the preparation and mode of application of the product. As the manufacturer cannot supervise the above procedures no warranty as to the fitness of the product for a particular purpose can be given provided that nothing herein shall be deemed to exclude, restrict or modify any condition or warranty expressed or implied by any statute whether State or Federal. With the constant advancement in technology we suggest that the information used in making recommendations from the literature be reviewed every six months. April 2014 Version 1.0